Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STORED”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42

Luminosity issues in 2009 100 GeV polarized proton run

Several luminosity issues are reviewed. Questions remain, which are stated for further investigation. Some suggestions are made for possible luminosity improvement. There are several factors affecting the luminosity in 2009 100 GeV polarized proton run: (1) The highest bunch intensity at RHIC early store (1.5 hour after accramp in this note) in 2009 is 1.25 x 10{sup 11} protons. In 2008 run, it was 1.42 x 10{sup 11} protons, which gives rise to 30% higher luminosity if other conditions are the same. Yellow ramp efficiency is identified as one of the main problem. Meanwhile, the beam-beam induced loss in about 1 hour into collision accounts actually no less than the ramp. (2) The typical transverse emittance at early store is 13 {pi}{micro}m for bunch intensity of 10{sup 11} protons, but it is 17 {pi}{micro} for 1.25 x 10{sup 11} protons. The increase of the emittance implies a 30% difference in luminosity if other conditions are the same. The emittance growth with electron cloud below instability threshold may be partially responsible. Meanwhile, the Booster scraping may also be relevant. (3) The luminosity lifetime in 2009 run is significantly lower than that in 2005, 2006, and 2008 runs. At the beam-beam parameter of 0.01, the typical average luminosity lifetime in early store is 10 hours in 2009, and it is 15 hours in previous runs. Given 8 hours of store time, this implies more than 20% of the difference in integrated luminosity. The 0.7 m betastar adopted in 2009 might be relevant, but the evidence is not fully convincing. On the other hand, the continuing RF voltage ramp in store may be of concern. (4) In the last month of the run, the polarization at RHIC early store is declined from 60% to 55%, a 30% reduction in p{sup 4} factor. It is noted that the Booster scraping is reduced in order to increase bunch intensity at RHIC, and the source polarization is also declined at the same time. Questions regarding these issues are discussed, and some suggestions are made.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Computations of the unsteady flow about a generic wing/pylon/finned-store configuration

An overset grid approach is used to carry out a set of computations of the unsteady flow about a generic wing, pylon, and finned-store configuration. The geometry, discretization procedure, and governing equations are presented. Thin-layer Navier-Stokes solutions are presented for four store separation cases: store in carriage position, store at two different separation positions, and a time-accurate simulation of the forced store separation from the wing pylon carriage. Computational results are compared with wind tunnel data for the three 'static store' cases. Dynamic loads and trajectory data are presented for the forced separation case.

Meakin, Robert L.↗

Optoelectronic associative memory

An associative optical memory including an input spatial light modulator (SLM) in the form of an edge enhanced liquid crystal light valve (LCLV) and a pair of memory SLM's in the form of liquid crystal televisions (LCTV's) forms a matrix array of an input image which is cross correlated with a matrix array of stored images. The correlation product is detected and nonlinearly amplified to illuminate a replica of the stored image array to select the stored image correlating with the input image. The LCLV is edge enhanced by reducing the bias frequency and voltage and rotating its orientation. The edge enhancement and nonlinearity of the photodetection improves the orthogonality of the stored image. The illumination of the replicate stored image provides a clean stored image, uncontaminated by the image comparison process.

Chao, Tien-Hsin↗

Effect of Storage on Performance of Super Nickel-Cadmium Cells

A study was undertaken to examine the capacity maintenance features of SUPER nickel-cadmium cells when stored for extended periods to determine whether the features change when the same kinds of positive plates as that used in nickel-hydrogen cells are used, The cells maintained their capacity when stored at 0 C in the discharged state and at 0 C in the charged state by continuously trickle charging. There was a capacity loss when stored in the open-circuit condition at 28 C. A cycling test at 17% depth of discharge for 2400 cycles using cells stored at various conditions showed that cells maintained good end of discharge voltage regardless of their storage history. However, the EOD voltages of stored cells were lower by 10 mV compared to those of fresh cells. The capacity at the end of the cycling test decreased for the stored cells by 2-7 Ah. The storage related capacity loss is lower for SUPER Ni-Cd cells compared to that of Ni-H2 cells containing a hydrogen precharge. The results suggest the pivotal role of hydrogen pressure in the capacity loss phenomenon.

Vaidyanathan, Hari↗

Forming Aggregations using Virtual Sharding: Lessons Learned from Simple Scalable Storage (S3)

Data aggregation is the ability to combine separate datasets to form a single new logical dataset provides users with a powerful abstraction. The advantage of an aggregate dataset is that the users are freed from having to understand, and incorporate into their workflow, knowledge about the (ad hoc) organization of the constituent datasets. However, aggregating large numbers of files can be computationally complex with data server systems performing many repetitive operations. As part of the authors work on subsetting data stored on Amazon Web Service (AWS) Simple Storage Service (S3), we developed technology to read portions of otherwise monolithic data files. This enables the formation of virtual shards for user in subsetting data stored in HDF5 (hierarchical data format, version 5) files. This same tool can be used to form aggregations that combine data stored in many HDF5 files when those files are stored on S3. The nature of the virtual sharding and the algorithm that exploits it for subsetting is such that it can also be used for aggregation with the need for many of the repetitive operations required by the per file aggregation techniques. We will present timing information that demonstrates the flexibility of this approach. However, the lessons learned is that while this is a useful result in and of itself, these very same techniques can be applied in other contexts where data are stored in services and on media other than S3. For example, this same technique can be applied to data stored on spinning disk. Pushing the envelope for S3 forced a reexamination of our data access techniques which lead to unexpected positive benefits.

Gallagher, James↗

Dynamic graph system for a semantic database

A method and system in a computer system for dynamically providing a graphical representation of a data store of entries via a matrix interface is disclosed. A dynamic graph system provides a matrix interface that exposes to an application program a graphical representation of data stored in a data store such as a semantic database storing triples. To the application program, the matrix interface represents the graph as a sparse adjacency matrix that is stored in compressed form. Each entry of the data store is considered to represent a link between nodes of the graph. Each entry has a first field and a second field identifying the nodes connected by the link and a third field with a value for the link that connects the identified nodes. The first, second, and third fields represent the rows, column, and elements of the adjacency matrix.

97 MATHEMATICS AND COMPUTING↗

Dynamic graph system for a semantic database

A method and system in a computer system for dynamically providing a graphical representation of a data store of entries via a matrix interface is disclosed. A dynamic graph system provides a matrix interface that exposes to an application program a graphical representation of data stored in a data store such as a semantic database storing triples. To the application program, the matrix interface represents the graph as a sparse adjacency matrix that is stored in compressed form. Each entry of the data store is considered to represent a link between nodes of the graph. Each entry has a first field and a second field identifying the nodes connected by the link and a third field with a value for the link that connects the identified nodes. The first, second, and third fields represent the rows, column, and elements of the adjacency matrix.

97 MATHEMATICS AND COMPUTING↗

SEPTUM MAGNET DESIGN FOR THE APS-U

The Advanced Photon Source is in the process of upgrading its storage ring from a double-bend to a multi-bend lattice as part of the APS Upgrade Project (APS-U). A swap-out injection scheme is planned for the APS-U to keep a constant beam current and to enable a small dynamic aperture. A septum magnet with a minimum thickness of 2 mm and an injection field of 1.06 T has been designed, delivering the required total deflecting angle is 89 mrad with a ring energy of 6 GeV. The stored beam chamber has an 8 mm x 6 mm super-ellipsoidal aperture. The magnet is straight; however, it is tilted in yaw, roll, and pitch from the stored beam chamber to meet the on axis swap out injection requirements for the APS-U lattice. In order to minimize the leakage field inside the stored beam chamber, four different techniques were utilized in the design. As a result, the horizontal deflecting angle of the stored beam was held to only 5 µrad, and the integrated skew quadrupole inside the stored beam chamber was held to 0.09 T. The detailed techniques that were applied to the design, field multipoles, and resulting trajectories of the injected and stored beams are reported.

Abliz, M.↗

Augmented Monitoring and Condition Assessment Program for SNF Wet Storage Life Extension - 20489

Approximately 27 MTHM of spent nuclear fuel (SNF) owned and managed by the U.S. Department of Energy, Office of Environmental Management is stored in the L Basin at the Savannah River Site (SRS). This 'DOE SNF' is comprised of approximately 12,000 aluminum-clad, aluminum-based fuel assemblies (∼7 MTHM), and approximately 2000 non-aluminum fuel assemblies (∼20 MTHM). A program is in progress to perform Non-Destructive Examination (NDE) of the fuel and their storage containers to characterize the materials' condition, and to evaluate the effects of service to enable continued safe wet storage of the SNF. The Augmented Monitoring and Condition Assessment Program (AMCAP), a two-part program to develop and implement remote underwater Non-Destructive Examination of the aluminum SNF, and of the containers of the non-aluminum SNF, respectively, is aimed at the characterization and evaluation of corrosion degradation of aluminum fuel and container materials. The predominant design of the aluminum SNF (ASNF) stored in L Basin is the Materials Test Reactor (MTR) equivalent design, a plate fuel design. These SNF are stored in 5'' diameter tubes or 5'' x 5'' squares (called bundles) that are nominally 12' or up to 14' long. The SNF is de-bundled and inspected using a custom-designed MTR Fuel Inspection Table. The inspection table provides for indexed fuel positioning for a video camera examination with controlled lighting. A total of 10 of the SNF originating from foreign research and test reactors were selected for examination based on burnup, enrichment, and prior damage caused by service/storage history. A special inspection campaign of these 10 assemblies is in progress. The observed corrosion damage included minor to moderate attack from general corrosion, pitting, crevice, end grain and galvanic corrosion. Example results from the completed inspections are shown and discussed. The focus is a comparison of the as-received condition versus the as-found current storage condition that will serve to validate Water Chemistry and Corrosion Monitoring Programs. The non-aluminum SNF (NASNF) stored in L Basin are of diverse design that includes various geometries with claddings of stainless steel, Zircaloy, and Hastelloy. The fuel core materials include uranium alloys, oxides/mixed oxides, and carbides. These SNF materials, originating from early experimental and test reactors, are in various physical forms including single fuel elements and cut pieces. The fuel is stored in L Basin in various configurations including in direct bundled storage in aluminum tubes and in isolation cans that are in the bundles or in a larger over-size storage container (OSC). Concern with inside-out corrosion and the potential loss of configuration control and ability to handle the storage containers prompted the development of remote NDE methods that include visual and UT technologies to assess the condition of the containers. Candidate stored materials were selected for a special inspection campaign; the development of the NDE methods for the inspection for galvanic, crevice and sediment-induced corrosion (inside-out) are discussed. A summary of the SNF storage in L Basin at the SRS, and an overview of the AMCAP to enable continued safe storage of DOE SNF are described. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

SLIGHTLY IRRADIATED FUEL (SIF) INTERIM DISPOSITION PROJECT

CH2M HILL Plateau Remediation Company (CH2M HILL PRC) is proud to submit the Slightly Irradiated Fuel (SIF) Interim Disposition Project for consideration by the Project Management Institute as Project of the Year for 2010. The SIF Project was a set of six interrelated sub-projects that delivered unique stand-alone outcomes, which, when integrated, provided a comprehensive and compliant system for storing high risk special nuclear materials. The scope of the six sub-projects included the design, construction, testing, and turnover of the facilities and equipment, which would provide safe, secure, and compliant Special Nuclear Material (SNM) storage capabilities for the SIF material. The project encompassed a broad range of activities, including the following: Five buildings/structures removed, relocated, or built; Two buildings renovated; Structural barriers, fencing, and heavy gates installed; New roadways and parking lots built; Multiple detection and assessment systems installed; New and expanded communication systems developed; Multimedia recording devices added; and A new control room to monitor all materials and systems built. Project challenges were numerous and included the following: An aggressive 17-month schedule to support the high-profile Plutonium Finishing Plant (PFP) decommissioning; Company/contractor changeovers that affected each and every project team member; Project requirements that continually evolved during design and construction due to the performance- and outcome-based nature ofthe security objectives; and Restrictions imposed on all communications due to the sensitive nature of the projects In spite of the significant challenges, the project was delivered on schedule and $2 million under budget, which became a special source of pride that bonded the team. For years, the SIF had been stored at the central Hanford PFP. Because of the weapons-grade piutonium produced and stored there, the PFP had some of the tightest security on the Hanford nuclear reservation. Workers had to pass through metal detectors when they arrived at the plant and materials leaving the plant had to be scanned for security reasons. Whereas other high-security nuclear materials were shipped from the PFP to Savannah River, S.C. as part ofa Department of Energy (DOE) program to consolidate weapons-grade plutonium, it was determined that the SIF should remain onsite pending disposition to a national repository. Nevertheless, the SIF still requires a high level of security that the PFP complex has always provided. With the 60-year PFP mission of producing and storing plutonium concluded, the environmental cleanup plans for Hanford call for the demolition of the 63-building PFP complex. Consequently, if the SIF remained at PFP it not only would have interfered with the environmental cleanup plans, but would have required $100 million in facility upgrades to meet increased national security requirements imposed after the 9/11 terrorist attacks. A new smaller and more cost-effective area was needed to store this material, which led to the SIF Project. Once the SIF project was successfully completed and the SIF was safely removed from PFP, the existing Protected Area at PFP could be removed, and demolition could proceed more quickly without being encumbered by restrictive security requirements that an active Protected Area requires. The lightened PFP security level brought by safely removing and storing the SIF would also yield lowered costs for deactivation and demolition, as well as reduce overall life-cycle costs.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Design of a thermosyphon-based thermal valve for controlled high-temperature heat extraction

Conventional concentrated solar power (CSP) is a reliable alternative energy source that uses the sun’s heat to drive a heat engine to produce electrical power. An advantage of CSP is its ability to store thermal energy for use during off-sun hours which is typically done by storing sensible heat in molten salts. Alternatively, thermal energy may be stored as latent heat in a phase-change material (PCM), which stores large quantities of thermal energy in an isothermal process. On-sun, the PCM melts, storing energy. Off-sun, the latent heat is extracted to produce dispatchable electrical power. Here, this paper presents the design of a thermosyphon-based device with sodium working fluid that is able to extract heat from a source as demand requires. A prototype has been designed to transfer 37 kW of thermal energy from a 600°C molten PCM tank to an array of 9% efficient thermoelectric generators (TEGs) to produce 3 kW of usable electrical energy for 5 h. This “thermal valve” design incorporates a funnel to collect condensate and a central shut-off valve to control condensate gravity return to the evaporator. Three circumferential tubes allow vapour transport up to the condenser. Pressure and a thermal resistance models were developed to predict the performance of the thermal valve. The pressure model predicts that the thermal valve will function as designed. The thermal resistance model predicts a 5500× difference in total thermal resistance between “on” and “off” states. The evaporator and condenser walls comprise 96% of the “on” thermal resistance, while the small parasitic heat transfer in the “off” state is primarily (77%) due to radiation losses. Lastly, this simple and effective technology can have a strong impact on the feasibility, scalability, and dispatchability of CSP latent storage. In addition, other industrial and commercial applications can benefit from this thermal valve concept.

14 SOLAR ENERGY↗

Beam studies at the SPEAR3 synchrotron using a digital optical mask

The 3GeV SPEAR3 synchrotron light source operates in top-up injection mode with up to 500 mA circulating in the storage ring (equivalently 392 nC). Each injection pulse contains 40–80 pC producing a contrast ratio between total stored charge and injected charge of about 6500:1. In order to study transient injected beam dynamics during user operations, it is desirable to optically image the injected pulse in the presence of the bright stored beam. In the present work this is done by imaging the visible component of the synchrotron radiation onto a digital micro-mirror-array device (DMD), which is then used as an optical mask to block out light from the bright central core of the stored beam. The physical masking, together with an asynchronously-gated, ICCD imaging camera, makes it possible to observe the weak injected beam component on a turn-by-turn basis. The DMD optical masking system works similar to a classical solar coronagraph but has some distinct practical advantages: i.e. rapid adaption to changes in the shape of the stored beam, a high extinction ratio for unwanted light and minimum scattering from the primary beam into the secondary optics. In this paper we describe the DMD masking method, features of the high dynamic range point spread function for the SPEAR3 optical beam line and measurements of the injected beam in the presence of the stored beam.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Framework for custom event sample augmentations for ATLAS analysis data

For HEP event processing, data is typically stored in column-wise synchronized containers, such as most prominently ROOT’s TTree, which have been used for several decades to store by now over 1 exabyte. These containers can combine row-wise association capabilities needed by most HEP event processing frameworks (e.g. Athena for ATLAS) with column-wise storage, which typically results in better compression and more efficient support for many analysis use-cases. One disadvantage is that these containers, TTree in the HEP use-case, require to contain the same attributes for each entry/row (representing events), which can make extending the list of attributes very costly in storage, even if those are only required for a small subsample of events. Since the initial design, the ATLAS software framework features powerful navigational infrastructure to allow storing custom data extensions for subsamples of events in separate, but synchronized containers. This allows adding event augmentations to ATLAS standard data products (such as DAOD-PHYS or PHYSLITE) avoiding duplication of those core data products, while limiting their size increase. For this functionality, the framework does not rely on any associations made by the I/O technology (i.e. ROOT), however it supports TTree friends and builds the associated index to allow for analysis outside of the ATLAS framework. A prototype based on the Long-Lived Particle search is implemented and preliminary results with this prototype will be presented. At this point, augmented data are stored within the same file as the core data. Storing them in separate files will be investigated in future, as this could provide more flexibility, e.g. certain sites may only want a subset of several augmentations or augmentations can be archived to tape once their analysis is complete.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Total cost of carbon capture and storage implemented at a regional scale: northeastern and midwestern United States

We model the costs of carbon capture and storage (CCS) in subsurface geological formations for emissions from 138 northeastern and midwestern electricity-generating power plants. The analysis suggests coal-sourced CO 2 emissions can be stored in this region at a cost of $52–$60 ton -1 , whereas the cost to store emission from natural-gas-fired plants ranges from approximately $80 to $90. Storing emissions offshore increases the lowest total costs of CCS to over $60 per ton of CO 2 for coal. Because there apparently is sufficient onshore storage in the northeastern and midwestern United States, offshore storage is not necessary or economical unless there are additional costs or suitability issues associated with the onshore reservoirs. For example, if formation pressures are prohibitive in a large-scale deployment of onshore CCS, or if there is opposition to onshore storage, offshore storage space could probably store emissions at an additional cost of less than $10 ton -1 . Finally, it is likely that more than 8 Gt of total CO 2 emissions from this region can be stored for less $60 ton -1 , slightly more than the $50 ton -1 Section 45Q tax credits incentivizing CCS.

Life Sciences & Biomedicine - Other Topics↗

Multifluid geo-energy systems: Using geologic CO 2 storage for geothermal energy production and grid-scale energy storage in sedimentary basins

We present an approach that uses the huge fluid and thermal storage capacity of the subsurface, together with geologic carbon dioxide (CO 2 ) storage, to harvest, store, and dispatch energy from subsurface (geothermal) and surface (solar, nuclear, fossil) thermal resources, as well as excess energy on electric grids. Captured CO 2 is injected into saline aquifers to store pressure, generate artesian flow of brine, and provide a supplemental working fluid for efficient heat extraction and power conversion. Concentric rings of injection and production wells create a hydraulic mound to store pressure, CO 2 , and thermal energy. This energy storage can take excess power from the grid and excess/waste thermal energy, and dispatch that energy when it is demanded and thus enable higher penetration of variable renewable energy technologies (e.g., wind, solar). CO 2 stored in the subsurface functions as a cushion gas to provide enormous pressure-storage capacity and displace large quantities of brine, some of which can be treated for a variety of beneficial uses. Geothermal power and energy-storage applications may generate enough revenues to compensate for CO 2 capture costs. While our approach can use nitrogen (N 2 ), in addition to CO 2 , as a supplemental fluid, and store thermal energy, this study focuses using CO 2 for geothermal energy production and grid-scale energy storage. We conduct a techno-economic assessment to determine the levelized cost of electricity of using this approach to generate geothermal power. We present a reservoir pressure-management strategy that diverts a small portion of the produced brine for beneficial consumptive use to reduce the pumping cost of fluid recirculation, while reducing the risk of seismicity, caprock fracture, and CO 2 leakage.

15 GEOTHERMAL ENERGY↗

Simulation INsight and Analysis

Sina is a tool set for modern scientific data management that provides flexible, light-weight support of non-bulk data capture for retention in and queries against SQL and noSQL data stores. HPC simulations traditionally maintain their data in files. Extracting data of interest for subsequent analysis then requires the time-consuming process of traversing directories and scraping data from files in a variety of formats. Sina facilitates capturing relevant data during execution or post-processing of simulation runs for retention in and queries from a modern data store. The tools are sufficiently general to allow for the inclusion of new fields as scientists learn more about their data. Libraries, currently in C++ and Python, and a command line interface (CLI) are provided. Sina's flexibility starts with a general schema, in JSON, for the collection of non-bulk simulation data. JSON provides a flexible, human-readable representation of the data that of interest. Sina currently has a C++ library for simulations to write data to and read from a schema-compliant file for subsequent ingestion into one of the supported data stores. However, applications are free to write their data directly into a schema-compliant file. Python packages provide data ingestion, management, query, and export capabilities. A command line interface (CLI) provides simplified access to these features. A common application programming interface (API) is used to maintain and query data in any of the supported data stores, which are currently limited to SQL and Apache Cassandra (a column store). Tutorials, demonstrations, and examples illustrate aspects of the process using scripts and Jupyter notebooks.

Pauli, EstebanT↗

Optimization performance, fidelity, and cost: SIAM VQE

This dataset contains files storing results from classically-simulated quantum subroutines within a dynamical mean-field theory workflow, and jupyter notebooks processing the data in these files to generate plots. The files store: (1) Results from variational quantum eigensolver (VQE) simulations searching for optimal parameters allowing parametrized quantum circuits to prepare approximations to ground states of different Anderson impurity models (AIMs) (2) Results from simulations of a quantum Lanczos algorithm (QLA) estimating the Lanczos coefficients defining the continued-fraction representation of an (AIM) Green’s function Description: Any file named vqe_gs_results* stores approximations to the ground state and energy of a given AIM estimated using three different methods: (1) Numerical diagonalization (2) Ideal VQE simulation (3) VQE simulation with sampling noise For each VQE simulations metadata about the optimization (optimization results plus number of quantum circuits that would have been executed on real hardware) is also stored. Any file named qla_dos_results* estimations for the Lanczos coefficients defining the Green’s function of an AIM. The stored estimations are achieved using different methods: (1) Numerical Lanczos algorithm from initial states obtained from numerical diagonalization (2) Simulated quantum Lanczos algorithm from initial states prepared from parametrized quantum circuits yielded by corresponding ideal and noisy VQE subroutines. The dataset is used and described in M. Karabin et al., "Quantum solver for single-impurity Anderson models with particle-hole symmetry", Phys. Rev. Research 8, 033066 (2026). DOI: https://doi.org/10.1103/7ys3-tl4l

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Methodology and Software for Gross Defect Detection of Spent Nuclear Fuel at the Atucha-I Reactor [Novel Methodology and Software for Spent Fuel Gross Defect Detection at the Atucha-I Reactor]

Here, fuel assemblies in the spent fuel pool are stored by suspending them in two vertically stacked layers at the Atucha Unit 1 nuclear power plant (Atucha-I). This introduces the unique problem of verifying the presence of fuel in either layer without physically moving the fuel assemblies. Given that the facility uses both natural uranium and slightly enriched uranium at 0.85 wt% 235 U and has been in operation since 1974, a wide range of burnups and cooling times can exist in any given pool. A gross defect detection tool, the spent fuel neutron counter (SFNC), has been used at the site to verify the presence of fuel up to burnups of 8000 MWd/t. At higher discharge burnups, the existing signal processing software of the tool was found to fail due to nonlinearity of the source term with burnup.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗