Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STEELS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42

Electrochemical Behavior of Steel in Concrete Under Wet and Dry Condition with NaCl Solution

The corrosion of steel and environmental factors in concrete under the wet and dry condition were examined by using electrochemical impedance spectroscopy (EIS) and microelectrode sensors. The concentration of chloride ion (CL) was detected by Ag/AgCl microelectrode, and the pH was monitored by W/WO{sub x} one. The CL increased step by step according to the wet and dry condition. Besides, the cathodic current of the oxygen (I{sub O{sub 2}}) was increased just after the immersion of concrete sample in wet process. These behaviors were thought to promote the corrosion of steel. From EIS, the rust was formed and destroyed on the surface of steel in concrete under the wet and dry condition. It was quantitatively demonstrated by monitoring that the corrosion of steel started when CL exceeded the threshold value in concrete under the wet and dry condition.

36 MATERIALS SCIENCE↗

Microstructure and Properties of AlCoCrFeNiTi High-Entropy Alloy Coating on AISI1045 Steel Fabricated by Laser Cladding

AISI1045 steel is widely used in mechanical engineering. In spite of the favorable toughness and strength, the surface properties of AISI1045 steel, such as hardness, wear resistance and corrosion resistance, are not ideal. Therefore, surface modification of AISI1045 is necessary, especially for the parts suffering severe work condition. Laser cladding is a promising surface modification technology. In this work, the AlCoCrFeNiTi high-entropy alloy (HEA) coatings were prepared on the AISI1045 steel to improve its surface properties. Metallurgical bonding is obtained between the coating and the substrate. The microstructure and surface properties of the coating were characterized by scanning electron microscope, energy-dispersive spectrometry, x-ray diffraction, electrochemical workstation, microhardness tester and pin-on-ring wear tester. The microstructure of the coating produced by laser cladding is dendritic. The AlCoCrFeNiTi HEA coating is mainly composed of disordered body-centered cubic phase (Fe-Cr), ordered B2 phase (AlNi) and intermetallic phase (Ti-rich). The coating shows excellent abrasion resistance and corrosion resistance in comparison with the substrate. The maximum microhardness of the coating reaches approximately 865 HV, which is 4.5 times of AISI1045 steel.

36 MATERIALS SCIENCE↗

Effect of Tempering Temperature on the Precipitation Behavior and Mechanical Properties of a Martensite Ferritic Steel

In this investigation, the precipitation of boron-containing M{sub 23}C{sub 6} in the CB2 steel during tempering was investigated. Scanning electron microscopy, energy-dispersive x-ray spectroscopy, transmission electron microscopy and differential scanning calorimetry were used to analyze the influence of temperature on the microstructure and properties of CB2-tempered martensite ferritic steel. The steel was normalized at 1100 °C for 2 h and then tempered at six different temperatures between 690 and 790 °C for 2 h. During air-cooling following austenitization, the precipitation of M{sub 3}C particles occurred in flakes forming with their diameter and thickness of 100 and 20 nm, respectively. The boron-containing M{sub 23}C{sub 6} was formed on the lath boundary after the dissolution of M{sub 3}C within the boundary. When the tempering temperature increased from 690 to 790 °C, the average diameter of boron-containing M{sub 23}C{sub 6} increased from 132 to 198 nm. Owing to the rapid growth of the precipitates, the phenomenon of lath widening as well as the recovery of microstructure would take place at high temperature. With an increase in the temperature, the tensile and yield strengths decreased gradually, while the plasticity increased and the boron-containing M{sub 23}C{sub 6} grew rapidly. Furthermore, when the tempering temperature exceeded 750 °C, the plasticity of CB2 steel was significantly improved.

36 MATERIALS SCIENCE↗

Characterization of a Cast Duplex Stainless Steel with 3.0%Cu and Modeling of Precipitation Hardening

Duplex stainless steels (DSSs) are corrosion-resistant alloys extensively used in aggressive environments. Cast DSSs may be selected for pipes, valves and pumps in chemical, petrochemical and nuclear industries. The grade steel ASTM A890 1B is an example of cast DSS with 2.7-3.3%Cu addition. Copper increases the resistance to many types of corrosion, especially in non-oxidizing environments. When the copper content is higher than 2%, the steel can be precipitation-hardened. In this work, the precipitation hardening of a DSS ASTM A890 1B steel with 3.0%Cu was studied and modeled for aging temperatures in the 450-600 °C range. Copper precipitates in the ferrite phase, but remains in solid solution in the austenite. The age hardening curves were modeled by ΔH = K(t){sup n} model, where ΔH is the increase in hardness, t is the aging time, and K and n are constants to be determined. The microstructure and substructure were investigated by scanning electron and transmission electron microscopes.

36 MATERIALS SCIENCE↗

Effect of Tempering Mode on the Microstructure and Mechanical Properties of a Lean Alloy Martensitic Steel: Conventional Reheating Versus Induction Reheating

The present study elucidates the effect of the reheating rate and tempering temperature on the type, size, and distribution of carbides/cementite formed within martensite (M)/lower bainite (LB) during the tempering of a high-strength low-alloy (HSLA) steel. A comparison is made between conventional reheating and induction reheating. All the experimental samples were quenched from the austenitization temperature of 920 °C for 30 min. An ultra-high yield strength of 1180 MPa and a good toughness of 94 J at 0 °C were obtained after tempering at 400 °C for 15 min by induction reheating (~ 100 °C/s), while in the case of conventional reheating (~ 2 °C/s) and tempering at 400 °C for 15 min, the steel had a high strength of 1159 MPa, but a poor toughness of 47 J at 0 °C. After induction reheating to 500 °C and tempering for 15 min, a higher toughness was obtained (91 J at 0 °C), but the strength was decreased to 967 MPa. Microstructural characterization revealed that fine needle-like carbides (ε-Fe{sub 2.4}C) were obtained by induction reheating to 400 °C and tempering for 15 min. However, samples tempered at 400 °C by conventional reheating and 500 °C by induction reheating both precipitated coarse θ-Fe{sub 3}C. In the former, θ-Fe{sub 3}C precipitated at locations that were previously austenite grain boundaries and led to tempered martensite embrittlement (TME). In the latter, Ostwald ripening occurred, and the precipitates could not maintain high strength. The excellent mechanical properties of induction reheated steel (400 °C, 15 min) are attributed to the following aspects: (a) The selection of appropriate tempering temperature did not lead to decarburization and ensured high strength, and (b) a high reheating rate promoted carbide dispersion and avoided TME in steel.

36 MATERIALS SCIENCE↗

Effects of Ce Addition on Grain Boundary Character Distribution, Corrosion Behavior and Impact Toughness of AISI 204Cu Stainless Steel

In this study, the effects of Ce addition on grain boundary character distribution, corrosion behavior and impact toughness of AISI 204Cu stainless steel were investigated. The results revealed that rare earth Ce affected the characteristics and size of inclusions, and the change in the austenite grain size was attributable to Ce multi-phase inclusions as the core of heterogeneous nucleation in stainless steel. The high adjacent probability of γ-fiber textures comprising {111} 〈110〉 and {111} 〈112〉 components was available for more ∑3{sup n} boundaries with increasing Ce contents, which was believed to have a contribution to the enhancement of corrosion resistance. Meanwhile, the austenite grain refinement and ∑3{sup n} boundaries increment were beneficial for the impact toughness improvement of Ce-added steel by increasing the difficulty of crack initiation and propagation. Adding excessive Ce caused a decline in the corrosion behavior and impact toughness of 204Cu stainless steel.

36 MATERIALS SCIENCE↗

Strain-Hardening Behavior of Dual-Phase Steel under Multistress States

The complexity and nonuniformity of microdeformation in high-strength dual-phase (DP) steels make it difficult to accurately predict the deformation processes in stamping. Here, in situ experiments under three kinds of stress states and a crystal plasticity finite element (CPFE) model were used to predict the strain-hardening behavior of DP steel. The microdeformation in various deformation stages was extracted from metallographs captured during in situ experiments to calculate the strain partitioning functions of each phase. Then, the multistress state mechanical behavior of DP steel was calculated based on the CPFE model combined with the strain partitioning functions of ferrite and martensite. The calculation results showed that (1) the CPFE model could accurately describe the load–stroke curves of the three experiments and that (2) the stress state had a significant effect on the strain partition ratio and the initial critical resolved shear stress of the material. In addition, the stress–strain curves of DP800 steel were predicted under six stress states; these curves did not coincide and had obvious deviations. Finally, the activity of the grain slip systems and the dislocation evolution were analyzed and discussed to predict the microdeformation and stress state effects on strain-hardening behavior.

36 MATERIALS SCIENCE↗

Interfacial Strength Evaluation of Oxide Films on Carbon Steel by Using the Laser Shock Adhesion Test

We investigate the adhesion strength (interfacial strength) of the oxide film formed on a carbon steel substrate by using a laser shock adhesion test (LaSAT). A rolled carbon steel (SS400) plate is first heated at high temperature (700 °C) under the atmosphere (heat treatment) to cause the formation of oxide films about 20-50 μm thick on the steel surface. The film consisted of multiple layers, including wustite (FeO), magnetite (Fe{sub 3}O{sub 4}), and hematite (Fe{sub 2}O{sub 3}). Next, the x-ray diffraction method was used to measure the residual stress in the film. We find that compression stress develops in the film because of a mismatch of thermal strain in between the film and substrate after the heat treatment. With LaSAT, strong elastic wave generates by a pulsed laser ablation of the substrate backside, and results in interfacial fractures in the oxide films. To monitor the normal (out-of-plane) displacement of the top surface film, a laser ultrasonic interferometer is simultaneously utilized, such that we detect film delamination and determine the critical laser energy for interfacial fracture to obtain the critical stress (interfacial strength). Furthermore, additional pulsed laser irradiation is conducted against a pre-delaminated specimen in order to examine the growth of delamination area and evaluate the interfacial fracture toughness. Finally, elastic wave propagation in the sample is computed using the finite element method (FEM) in order to evaluate the interfacial stress field, accurately. For the FEM, multiple layers in the oxide film are modeled, and the residual stress due to thermal strain mismatch is introduced. The FEM computations reveal the stress distribution around the interface and evaluate the critical stress and critical stress intensity factor for delamination. We thus quantitatively evaluate the interfacial strength and interfacial fracture toughness of the oxide film formed on carbon steel. The mechanism of interfacial fracture is also discussed on the basis of microstructures in a film with multiple layers. This result may be useful for understanding the adhesion quality of oxide film during the hot-rolling process.

36 MATERIALS SCIENCE↗

Cu Interlayer-Induced High-Strength Laser-Welded AISI 304 Steel-Niobium Joint

Joining niobium to austenitic stainless steel is necessary for the fabrication of particle accelerators. However, the brittle iron-niobium intermetallics formed in the joint significantly reduce the joint strength. Copper was used as an interlayer to prevent the brittle phase formation while joining niobium to AISI 304 steel. The laser beam was first focused on the Cu-steel faying surface and then on the Cu-Nb faying surface. The tensile strength of the joint is greater than that of the Nb. The weld microstructure consists of austenite with Cu-rich precipitates along with the austenitic grain boundaries and Cu-rich phase embedded with Nb-rich particles and dendrites. Solid solution strengthening of Cu by Fe and second-phase strengthening of Cu by Nb play a critical role in improving the mechanical properties of the joint. These results highlight new possibilities for the joining of niobium to steel.

36 MATERIALS SCIENCE↗

Improved Mechanical Properties of Structural Steel via Developing Bimodal Grain Size Distribution and Intercritical Heat Treatment

Intercritical annealing and tempering heat treatment combined with cold rolling were applied for improvement of tensile properties and strain-hardening rate of structural steel. Coarse dual-phase (DP) microstructure was processed via intercritical heat treatment of the ferritic–pearlitic sheet, which resulted in the increase in tensile strength and disappearance of the yield point phenomenon. However, the tensile toughness was not effectively enhanced, which is indicative of unaltered strength–ductility trade-off. A bimodal-sized ferrite structure was obtained by cold rolling of the DP microstructure followed by subcritical annealing (tempering), where its characteristic features are high yield stress and relatively poor work-hardening response. Afterward, the intercritical annealing of the bimodal steel resulted in the development of fine DP steel with excellent work-hardening capacity and pronounced enhancement of tensile toughness. Conclusively, this work demonstrates the possibility of controlling the tensile properties and work-hardening behavior of conventional steels by simple heat treatment routes with the aid of cold rolling.

36 MATERIALS SCIENCE↗

Comparative Corrosion Behavior of Five Different Microstructures of Rebar Steels in Simulated Concrete Pore Solution with and Without Chloride Addition

The present work discusses the effect of five different microstructures, coarse, fine and very fine ferrite–pearlite, martensite and tempered martensite, made by furnace cooling, air cooling, forced air-cooling, water quenching and tempering, respectively, of a rebar steel on its corrosion performance in freely aerated with and without chloride-contaminated simulated concrete pore solution using the dynamic polarization and electrochemical impedance spectroscopy. The corrosion performance of the steels with five different microstructures relates to the polarization resistance, protective ability of rusts and the extent of the galvanic attack. The corrosion rate of the steels has been found to be comparable in the simulated concrete pore (SCP) solution. However, in chloride-containing SCP solution, corrosion rate has been found to increase in the following sequence: forced air-cooled–air-cooled–quenched–furnace-cooled–tempered steels.

36 MATERIALS SCIENCE↗

Enhancement of Wear and Corrosion Resistance in Medium Carbon Steel by Plasma Electrolytic Nitriding and Polishing

The effect of plasma electrolytic polishing on the characteristics of medium carbon steel after anodic nitriding in a nitrate–chloride electrolyte was investigated. The structure, morphology, and phase composition of the layers were studied using an x-ray diffractometer and a metallographic microscope. Nitrided and polished specimens were tested under dry friction conditions with a counter-body made of bearing steel. Corrosion studies were performed using potentiodynamic polarization curves in 3% sodium chloride solution. Nitriding in a nitrate–chloride electrolyte was determined to increase the surface hardness up to 1040 HV due to the formation of a nitride–martensite layer with an outer oxide layer. After polishing of the nitrided surface, the loose outer part of the oxide layer containing microcracks and pores was removed. The reduction in the corrosion current density of 2.27 times of nitrided steel by plasma polishing without changing the structure of the diffusion layers was shown. The wear rate of the samples decreased from 560 μg/(N m) for untreated steel to 60 μg/(N m) as a result of nitriding and dropped to 8 μg/(N m) after plasma electrolytic polishing.

36 MATERIALS SCIENCE↗

Study of Rare Earth Additions Effect on the Solidification and Properties of 4130 Steel

This paper covers a set of experiments where two different rare earth additions were made to 4130 steel. A thermal analysis system was employed to measure solidification reactions and determine whether changes from the baseline occurred. Keel block castings were also poured and then machined into tensile bars. Mechanical testing found an increase in strength. Electron microscopy found RE oxysulfides had formed in the steel. Examination of the cooling rate curves noted the formation of additional phases during the solidification of the RE treated steels. The peritectic and solidus temperatures of the treated steels increased, indicating that the RE inclusions acted as heterogeneous nuclei for austenite during freezing.

36 MATERIALS SCIENCE↗

Effects of Heat Treatment Parameters on the Microstructure and Properties of Bainitic Steel

The results obtained in the present study demonstrate the effects of various types of heat treatment processes on the microstructure and hardness of new trip-assisted carbide-free bainitic steel. The steel was subjected to three variants of heat treatment processing with an isothermal bainitic transformation temperature in a range from 350 to 480 °C. Changes of temperature and time of isothermal holding caused changes in the values of retained austenite (RA) volume fraction and carbon content. Reduction in the isothermal holding temperature resulted in the increased concentration of carbon in austenite. Also, the investigations of the microstructure showed that size and morphology of the austenite evolved during heat treatment. The SEM observations revealed that the steel subjected to heat treatment is composed of the carbide-free bainite with ferrite plates and a high volume fraction of retained austenite in the form of thin layers or islands. With the lower isothermal holding temperature and the higher degree of bainitic transformation, the more the RA morphology changed from island to layer type. The application of the lowest isothermal temperature resulted in a significant refinement of the microstructure components: the bainitic ferrite plates and the RA layers. Also, the mechanical properties obtained from the tensile testing and hardness measurements were correlated to the microstructure of the investigated steel after different isothermal holdings.

36 MATERIALS SCIENCE↗

Development of Low-Alloy Steels with High Strength and Good Ductility with the Aid of Nanoscale Troostite

We aimed to design nanoscale troositic microstructures in medium-carbon low-alloyed steel by using annealing plus quenching–partitioning–tempering processes to simultaneously obtain high strength and good ductility. The troositic microstructure and the related mechanical properties of the studied steel were studied systematically. After quenching to 200 °C in 5 s and then holding at various partitioning temperatures for 60 s and subsequently tempering at 400 °C for 1800 s, the steel held at the partitioning temperature of 200 °C for 60 s exhibited a high tensile strength (σ{sub TS}) of 1620 ± 10 MPa and a yield strength (σ{sub y}) of 1220 ± 10 MPa, together with a good ɛ{sub f} of 25% at a strain rate of 1 × 10{sup −3} s{sup −1}. Both σ{sub TS} and σ{sub y} values were two times higher than the values for the coarse-grained counterpart with identical chemical composition. The key strengthening factor is associated with the nanoscale troostite phase. The mechanical properties of the steel with an average thickness of troositic lamellae at 200 ± 15 nm are consistent with the line predicted by the H–P relationship.

36 MATERIALS SCIENCE↗

Effect of Cu Interlayer on the Microstructure and Strength for Brazing of Tungsten/316L Steel

Brazing is an effective technique for joining tungsten and steel. However, the high residual stresses are produced due to the different coefficients of thermal expansions between tungsten and steel. Compared with the direct brazing with BNi-2 foil filler, BNi-2/Cu/ BNi-2 multiple interlayer was used as filler to minimize the residual stresses between tungsten and 316L steel. The brazing experiments were conducted at 1050 °C for 25 min using Cu foils with different thickness. The results show that tungsten and 316L steel have been successfully joined by brazing. The intermetallic compound of NiW formed at the W/BNi-2 interface, which was detrimental to the strength of the joint. The microhardness of different diffusion zones is higher than that of the substrates owing to the formation of intermetallic compound and solid solution. All specimens of shear testing fractured at the W/BNi-2 interface close to W substrate, and the average strength of joints was 197, 275 and 268 MPa with multiple interlayer thickness of 0.2 , 0.1 and 0.05 mm copper foil, respectively, while the average strength of joints was 143 MPa with BNi-2 foil filler. The significant increase in the joint shear strength can be ascribed to the Cu foil in the multiple interlayer because of with excellent plasticity and toughness.

36 MATERIALS SCIENCE↗

Laser spot welding of additive manufactured 304L stainless steel

Here, the goal of this work is to understand if an additively manufactured 304L stainless steel exhibits similar spot-welding behavior as wrought 304L stainless steel. Due to the many differences between an additively manufactured component and wrought product, it is important to determine how the material interacts with the laser and how it affects the weld bead morphology. In this paper, the laser coupling efficiency, weld size, and solidification of spot welds produced in wrought and additively manufactured 304L stainless steel were investigated. The coupling efficiency of wrought and additively manufactured 304L stainless steel of similar surface condition were approximately the same over a range of applied laser energies. Laser welding of the untreated (rougher) surface of additively manufactured 304L, however, showed improved coupling efficiency ranging between 3.3 and 100%. The rougher surface traps the incoming light and increases the coupling efficiency at lower laser energies, while at higher energy, the absorption efficiency is dominated by intrinsic absorption from the keyhole formation rather than surface roughness. The resulting spot weld microstructures differed from welds made in wrought 304L and additively manufactured 304L. Welds made in wrought 304L were fully austenitic containing what is suspected to be massive austenite, which suggests that these welds solidified as primary ferrite. Welds made in additively manufactured 304L were also fully austenitic and contained both cellular austenite and what is suspected to be massive austenite. These observations mean that welds made in additively manufactured 304L solidified as primary ferrite and primary austenite. The differences in weld microstructures made in wrought and AM 304L can be attributed to differences in the composition and solidification rate.

304L stainless steel↗

An in-situ high-energy X-ray diffraction study of micromechanical behavior of multiple phases in advanced high-strength steels

For multiphase advanced high-strength steels, the different mechanical behavior of constituent phases may lead to a non-uniform partitioning of stresses among different phases. In addition, the grain-orientation-dependent elastic/plastic anisotropy in each phase may cause the grain-to-grain interactions, which further modify further the microscopic load partitioning. In the current work, the micromechanical behavior of high-strength steels with multiple phases was characterized by using the in-situ high-energy X-ray diffraction (HEXRD) technique. For the investigated materials, the {200} lattice strains of the constituent phases (the ferrite, bainite, and martensite) with similar crystal structures were determined through separating their overlapped diffraction peaks and, then, examining the respective changes of peak positions during deformation. Based on those experimental data, the anisotropic elastic and plastic properties of the steels were simulated using a Self-Consistent (SC) model for predicting the grain-to-grain and phase-to-phase interactions. The constitutive laws for describing the elastic and plastic behavior of each constituent phase were directly obtained through comparing the predicted lattice- strain distributions with the measured ones. The transmission-electron-microscopy (TEM) observations of the microstructure developments of microstructures also verified the partitioning of plastic strains among different phases. The present investigations provide a good fundamental understanding of the micromechanical behavior, with an emphasis on the stress partitioning of soft and hard phases, and different work-hardening rates, of the studied steels during tensile loading.

36 MATERIALS SCIENCE↗