Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SHOCK LAYER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Unsteady separation in sharp fin-induced shock wave/turbulent boundary layer interaction at Mach 5

Fluctuating wall-pressure measurements are made in shock-wave/turbulent-boundary-layer interactions generated by sharp/unswept fins at angles of attack of 16, 18, 20, 22, 24, 26, and 28 degrees at Mach 5. The experiment was conducted under approximately adiabatic wall temperature conditions. The mean and rms pressure distributions can be collapsed in conical coordinates. The wall-pressure signal near separation is intermittent for all angles of attack (16-28 deg) and is qualitatively similar to that measured in unswept flows. However, the shock frequencies are higher - about 5 kHz compared to 0.5-1 kHz. Over the range of sweepbacks examined, from 25-55 deg, the spectral content of the fluctuating pressures does not change. Thus, the increase in separation-shock frequency from 1 to 5 kHz occurs at lower interaction sweepback and is not a continuous process with increasing sweepback. Power spectra at the position of maximum rms in the intermittent region for interactions in different incoming boundary layers have the same center frequency. The maximum rms in the intermittent region correlates with interaction sweepback, not with overall inviscid pressure rise.

Schmisseur, J. D.↗
NASA NTRS1985

Hybrid approach to steady transonic normal shock-compressible laminar boundary layer interactions over airfoils with suction

Transonic airfoil flow is to a large degree affected by viscous-inviscid interactions. Among them a key role is played by the boundary layer interaction with the shock wave embedded in the flow field and the interaction of the boundary layer with the sustained adverse pressure gradients. The effects of these interactions can be controlled or suppressed by introducing surface mass transfer such as suction. This investigation deals strictly with the study of shock-laminar boundary layer interactions including distributed mass transfer. The present calculations agree with experiments on a swept LFC wing at low speeds which indicates that with a suitable choice of the extent of the airfoil surface over which suction is applied and adjustment of the suction velocity, full-chord laminar flow can be maintained and separation can be prevented completely.

Ram, R. B.↗
NASA NTRS1986

Shock wave/turbulent boundary layer interaction in the flow field of a tri-dimension wind tunnel

The first results of a thorough experimental analysis of a strong three-dimensional shock-wave/turbulent boundary-layer interaction occurring in a three dimensional transonic channel are presented. The aim of this experiment is to help in the physical understanding of a complex field, including several separations, and to provide a well documented case to test computational methods. The flowfield has been probed in many points by means of a three-component laser Doppler velocimeter. The results presented relate only to the mean velocity field. They clearly show the formation in the flow of a strong vortical motion resulting from the shock wave interaction.

Benay, R.↗
NASA NTRS1947

Drag Reduction by Suction of the Boundary Layer Separated Behind Shock Wave Formation at High Mach Numbers

With an approach of the velocity of flight of a ship to the velocity of sound, there occurs a considerable increase of the drag. The reason for this must be found in the boundary layer separation caused by formation of shock waves. It will be endeavored to reduce the drag increase by suction of the boundary layer. Experimental results showed that drag increase may be considerably reduced by this method. It was, also, observed that, by suction, the position of shock waves can be altered to a considerable extent.

Regenscheit, B.↗
NASA NTRS1990

A study of the unsteadiness of crossing shock wave turbulent boundary layer interactions

The unsteadiness of crossing shock wave turbulent boundary layer interactions at a nominal Mach number of 3 was examined by measuring wall pressure fluctuations using multiple, high frequency response, pressure transducers. The unsteadiness in the initial part of the interaction for all the interactions is similar to that of single fin interaction as studied by Tran and Bogdonoff (1987). However, for stronger interactions, flow downstream of the inviscid shock crossing position has a significant unsteady characteristic. In this unsteady region of the interaction, mean surface pressure rises significantly over the value obtained from the inviscid shock approximation. The energy spectrum of the fluctuating pressure signal shows a significant increase in the energy level at the higher frequencies.

Poddar, K.↗
NASA NTRS1972

Characteristics of the unsteady shock-induced laminar boundary layer on a flat plate.

The unsteady shock-induced laminar boundary layer on a flat plate is theoretically studied for shock speeds ranging from 1.12 to 9 km/sec. Boundary layer flows for real air, assumed to be in thermochemical equilibrium, are analyzed by extending Lam's work on shock-induced laminar boundary layers to equilibrium dissociated and ionized flows. A complete description of the unsteady nature of the boundary layer is presented in terms of heat transfer and several boundary layer thickness quantities as functions of a single time-position variable. Boundary layer development is considered for two points of view. Time-dependent boundary layer development and approach to steady state for any fixed position on the plate is described, as is the configuration of the boundary layer with position on the plate at any point in time.

Cook, W. J.↗
NASA NTRS1998

Shock Wave Boundary Layer Interactions in High Mach Number Flows: A Critical Survey of Current Numerical Prediction Capabilities

The report assesses the capability for numerical simulation of 2-D and 3-D shock wave laminar and turbulent boundary layer interactions Three fundamental configurations are considered: single fin, double fin, and hollow cylinder flare. Thirteen separate cases were examined by a distinguished international group of researchers using the Reynolds-averaged Navier-Stokes (RANS) equations with a wide range of turbulence models from zero equation to full Reynolds Stress Equation formulations. The report presents an extensive comparison of computations and experimental data, summarizes the results, and makes recommendations for future research.

Doyle D. Knight↗
NASA NTRS1989

An LDA (Laser-Doppler Anemometry) investigation of three-dimensional normal shock wave boundary-layer interactions

Nonintrusive measurements were made of a normal shock wave/boundary layer interaction. Two dimensional measurements were made throughout the interaction region while 3-D measurements were made in the vicinity of the shock wave. The measurements were made in the corner of the test section of a continuous supersonic wind tunnel in which a normal shock wave had been stabilized. Laser Doppler Anemometry, surface pressure measurement and flow visualization techniques were employed for two freestream Mach number test cases: 1.6 and 1.3. The former contained separated flow regions and a system of shock waves. The latter was found to be far less complicated. The results define the flow field structure in detail for each case.

Chriss, R. M.↗
NASA NTRS1993

Flowfield dynamics in blunt fin-induced shock wave/turbulent boundary layer interactions

Fluctuating wall pressure measurements were made on centerline upstream of a blunt fin in a Much 5 turbulent boundary layer. By examining the ensemble average wall pressure distributions for different fixed shock foot positions, it was shown that local fluctuating wall pressure measurements are due to a distinct pressure distribution, P(i), which undergoes a stretching and flattening effect as its upstream boundary translates aperiodically between the upstream influence and separation lines. The locations of the maxima and minima in the centerline wall standard deviation distribution can be accurately predicted using this distribution, providing quantitative confirmation of the model. This model also explains the observed cross-correlations and ensemble average measurements within the interaction. Using the P(i) model, wall pressure signals from under the separated flow region were able to reproduce the position-time history of the separation shock foot. The negative time delay peak in the cross-correlation between the predicted and actual shock foot histories shows that the separated region fluctuations precede shock foot motion.

Brusniak, L.↗
NASA NTRS1994

Flowfield dynamics in blunt fin-induced shock wave/turbulent boundary layer interactions

Fluctuating wall pressure measurements have been made on centerline upstream of a blunt fin in a Mach 5 turbulent boundary layer. By examining the ensemble averaged wall pressure distributions for different separation shock foot positions, it has been shown that local fluctuating wall pressure measurements are due to a distinct pressure distribution, Rho(sub i), which undergoes a stretching and flattening effect as its upstream boundary translates aperiodically between the upstream influence and separation lines. The locations of the maxima and minima in the wall pressure standard deviation can be accurately predicted using this distribution, providing quantitative confirmation of the model. This model also explains the observed cross-correlations and ensemble average measurements within the interaction. Using the Rho(sub i) model, wall pressure signals from under the separated flow region were used to reproduce the position-time history of the separation shock foot. Further, the negative time delay peak in the cross-correlation between the predicted and actual shock foot histories suggests that the separated region fluctuations precede shock foot motion. The unsteady behavior of the primary horseshoe vortex and its relation to the unsteady separation shock are described.

Dolling, David S.↗
DOE OSTI2020

Damage initiation and evolution in Al-Si layered microstructures under shock loading conditions at atomic scales

Designing materials with microstructural features like multiphase interfaces have shown significant promise for usage in the next generation defense and nuclear applications. The dynamic response of these interfaces in extreme environments is observed to vary with the deformability of individual phases, which could subsequently alter the favored damage nucleation sites related to spall failure. Here, we investigate the role of spacing of interfaces in a nanocrystalline layered Aluminum-Silicon system on the shock wave propagation behavior, and microstructural and defect evolution using classical molecular dynamics simulations. The simulations are carried out with different hypothetical Al/Si microstructures including variations in the distribution of Si grains as layers in a nanocrystalline Al matrix. The molecular dynamics simulations suggest that spall failure is preferentially initiated at Al/Si interfaces. In addition, for the same system volume and same concentration of Si, a higher number of layers is marked by an increase in shock wave velocity and reduced resistance to spall failure.

36 MATERIALS SCIENCE↗
NASA NTRS1974

Weak incident shock interactions with Mach 8 laminar boundary layers

Weak shock-wave interactions with boundary layers on a flat plate were investigated experimentally in Mach 8 variable-density tunnel for plate-length Reynolds numbers. The undisturbed boundary layers were laminar over the entire plate length. Pressure and heat-transfer distributions were obtained for wedge-generated incident shock waves that resulted in pressure rises ranging from 1.36 to 4.46 (both nonseparated and separated boundary-layer flows). The resulting heat-transfer amplifications ranged from 1.45 to 14. The distributions followed established trends for nonseparated flows, for incipient separation, and for laminar free-interaction pressure rises. The experimental results corroborated established trends for the extent of the pressure rise and for certain peak heat-transfer correlations.

Kaufman, L. G., II↗
NASA NTRS2015

Experimental Study of Fillets to Reduce Corner Effects in an Oblique Shock-Wave/Boundary Layer Interaction

A test was conducted in the 15 cm x 15 cm supersonic wind tunnel at NASA Glenn Research Center that focused on corner effects of an oblique shock-wave/boundary-layer interaction. In an attempt to control the interaction in the corner region, eight corner fillet configurations were tested. Three parameters were considered for the fillet configurations: the radius, the fillet length, and the taper length from the square corner to the fillet radius. Fillets effectively reduced the boundary-layer thickness in the corner; however, there was an associated penalty in the form of increased boundary-layer thickness at the tunnel centerline. Larger fillet radii caused greater reductions in boundary-layer thickness along the corner bisector. To a lesser, but measureable, extent, shorter fillet lengths resulted in thinner corner boundary layers. Overall, of the configurations tested, the largest radius resulted in the best combination of control in the corner, evidenced by a reduction in boundary-layer thickness, coupled with minimal impacts at the tunnel centerline.

Fillets↗
NASA NTRS1995

Experimental study of the use of vortex generators to reduce fluctuating pressure loads in shock wave turbulent boundary layer interactions

Fluctuating wall pressure measurements have been made in a separated shock wave/turbulent boundary layer interaction produced by an unswept compression corner in a Mach 5 flow. Wheeler doublet vortex generators were placed 15.8 boundary layer thicknesses upstream of the corner to study their effect on the fluctuating pressure loads produced by the translating separation shock. The vortex generators produced significant three-dimensionality in an otherwise two-dimensional interaction. They reduced the upstream influence and the length of the region of shock motion by 60% and 64%, respectively, decreased the maximum wall pressure rms by 23%, and shifted the fluctuations to a higher frequency band. The maximum fraction of energy in the 100-500 Hz frequency band is decreased by 11%. These changes are due to a fuller boundary layer profile, a weaker separation shock, and increased boundary layer turbulence causing increased separation shock jitter.

Barter, John W.↗
NASA NTRS1976

The structure of shock wave-boundary layer interactions in transonic flow

The structure of transonic shock wave-boundary layer interactions is studied using asymptotic analyses, for an oblique shock impinging on a flat plate boundary layer. Solutions for unseparated laminar and turbulent boundary layers are reviewed, and incipient separation of a turbulent boundary layer is considered.

Adamson, T. C., Jr.↗
NASA NTRS1977

Direct measurements of wall shear stress by buried wire gages in a shock-wave boundary-layer interaction region

Detailed measurements of wall shear stress (skin friction) were made with specially developed buried wire gages in the interaction regions of a Mach 2.9 turbulent boundary layer with externally generated shocks. Separation and reattachment points inferred by these measurements support the findings of earlier experiments which used a surface oil flow technique and pitot profile measurements. The measurements further indicate that the boundary layer tends to attain significantly higher skin-friction values downstream of the interaction region as compared to upstream. Comparisons between measured wall shear stress and published results of some theoretical calculation schemes show that the general, but not detailed, behavior is predicted well by such schemes.

Murthy, V. S.↗
NASA NTRS1983

Investigation to optimize the passive shock wave-boundary layer control for supercritical airfoil drag reduction

The optimization of passive shock wave/boundary layer control for supercritical airfoil drag reduction was investigated in a 3 in. x 15.4 in. Transonic Blowdown Wind Tunnel. A 14% thick supercritical airfoil was tested with 0%, 1.42% and 2.8% porosities at Mach numbers of .70 to .83. The 1.42% case incorporated a linear increase in porosity with the flow direction while the 2.8% case was uniform porosity. The static pressure distributions over the airfoil, the wake impact pressure data for determining the profile drag, and the Schlieren photographs for porous surface airfoils are presented and compared with the results for solid-surface airfoils. While the results show that linear 1.42% porosity actually led to a slight increase in drag it was found that the uniform 2.8% porosity can lead to a drag reduction of 46% at M = .81.

Nagamatsu, H. T.↗