Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Performance tests”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42

Measurements of Gas Bubble Size Distributions in Flowing Liquid Mercury

ABSTRACT Pressure waves created in liquid mercury pulsed spallation targets have been shown to induce cavitation damage on the target container. One way to mitigate such damage would be to absorb the pressure pulse energy into a dispersed population of small bubbles, however, measuring such a population in mercury is difficult since it is opaque and the mercury is involved in a turbulent flow. Ultrasonic measurements have been attempted on these types of flows, but the flow noise can interfere with the measurement, and the results are unverifiable and often unrealistic. Recently, a flow loop was built and operated at Oak Ridge National Labarotory to assess the capability of various bubbler designs to deliver an adequate population of bubbles to mitigate cavitation damage. The invented diagnostic technique involves flowing the mercury with entrained gas bubbles in a steady state through a horizontal piping section with a glass-window observation port located on the top. The mercury flow is then suddenly stopped and the bubbles are allowed to settle on the glass due to buoyancy. Using a bright-field illumination and a high-speed camera, the arriving bubbles are detected and counted, and then the images can be processed to determine the bubble populations. After using this technique to collect data on each bubbler, bubble size distributions were built for the purpose of quantifying bubbler performance, allowing the selection of the best bubbler options. This paper presents the novel procedure, photographic technique, sample visual results and some example bubble size distributions. The best bubbler options were subsequently used in proton beam irradiation tests performed at the Los Alamos National Laboratory. The cavitation damage results from the irradiated test plates in contact with the mercury are available for correlation with the bubble populations. The most effective mitigating population can now be designed into prototypical geometries for implementation into an actual SNS target.

99 GENERAL AND MISCELLANEOUS↗

Testing and evaluation of the Sandia Smart Pre-concentrator using a vapor generation system

Sandia National Laboratories (SNL) was contracted by the Defense Threat Reduction Agency (DTRA), through KBRwyle to perform testing and evaluation of the SNL Smart Pre-concentrator (SPC) system and a COTS FTIR system procured by DTRA through KBRwyle. Two common chemical warfare agent simulants, dimethyl methylphosphonate and triethyl phosphate were selected as the compounds of interest. SNL tested both systems using a COTS vapor generation system, capable of delivering known concentrations of specific chemical compounds to both detection systems, with Sandia responsible for the SPC system. Both systems were measured against COTS sorbent collection tubes analyzed by SNL via a laboratory GCMS system. Concentrations measured from tubes upstream from the FTIR system differed from the expected concentrations, while downstream tubes were mostly within 20% of the target concentration.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Study on the characteristics of a two gap capillary discharge

The paper presents a new two-gap capillary (TGC) discharge structure. The prominent innovation is the introduction of the middle electrode, which divides the capillary into the trigger gap and the main gap. The discharge circuit of the TGC comprises the trigger circuit and the main circuit. The two circuits are used for the pre-ionization of the trigger gap and providing energy of 450 J for the main gap arc discharging, respectively. When the discharge initiates, the trigger gap is pre-ionized under high voltage pulse produced by trigger circuit, and meanwhile, the weakly ionized plasma is generated. The main circuit then maintains the expansion of the plasma, which is called soft capillary discharge. Afterwards, the main gap is shorted and discharges under a relatively low voltage. With the optimization of the circuit parameter, both the energy deposition ratio in main gap and the degree of plasma ionization are enhanced. The efficiency of the energy deposition is almost twice higher compared with that of the conventional capillary structure. The life performance test indicates that the erosion of the middle electrode and the trigger gap carbonization are the key factors that limit the life performance of the TGC.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

ESTIMATION OF CRACK-ARREST TOUGHNESS TRANSITION AND NDT TEMPERATURES FROM CHARPY FORCE-DISPLACEMENT IMPACT TRACES

A force-displacement trace of a Charpy impact test of a reactor pressure vessel (RPV) steel in the transition range has a characteristic point, the so-called force at the end of unstable crack propagation , Fa. A two-parameter Weibull probability function is used to model the distribution of the Fa in Charpy tests performed at ORNL on different RPV steels in the unirradiated and irradiated conditions. These data have a good replication at a given test temperature, thus, the statistical analysis was applicable. It is shown that when temperature is normalized to TNDT (T-TNDT) or to T100a (T-T100a), the median Fa values of different RPV steels have a tendency to form the same shape of temperature dependence. Depending on normalization temperature, TNDT or T100a, it suggests a universal shape of the temperature dependence of Fa for different RPV steels. The best fits for these temperature dependencies are presented. These dependencies are suggested for use in estimation of NDT or T100a from randomly generated Charpy impact tests. The maximum likelihood methods are used to derive equations to estimate TNDT and T100a from randomly generated Charpy impact tests.

Sokolov, Mikhail A↗

Defining window-boundaries for genomic analyses using smoothing spline techniques

High-density genomic data is often analyzed by combining information over windows of adjacent markers. Interpretation of data grouped in windows versus at individual locations may increase statistical power, simplify computation, reduce sampling noise, and reduce the total number of tests performed. However, use of adjacent marker information can result in over- or under-smoothing, undesirable window boundary specifications, or highly correlated test statistics. We introduce a method for defining windows based on statistically guided breakpoints in the data, as a foundation for the analysis of multiple adjacent data points. This method involves first fitting a cubic smoothing spline to the data and then identifying the inflection points of the fitted spline, which serve as the boundaries of adjacent windows. This technique does not require prior knowledge of linkage disequilibrium, and therefore can be applied to data collected from individual or pooled sequencing experiments. Moreover, in contrast to existing methods, an arbitrary choice of window size is not necessary, since these are determined empirically and allowed to vary along the genome.

59 BASIC BIOLOGICAL SCIENCES↗

Comparison of electromagnetic, thermal and mechanical calculations with rf test results in rf-dipole deflecting/crabbing cavities

The current requirements of higher gradients and strict dimensional constraints in the emerging applications have required the designing of compact deflecting and crabbing rf structures. The superconducting rf-dipole cavity is one of the first novel compact designs with attractive properties such as higher gradients, higher shunt impedance and widely separated higher order modes. The recent tests performed on proof-of-principle designs of the rf-dipole geometry at 4.2 K and 2.0 K in the vertical test area at Jefferson Lab have proven the designs to achieve higher gradients with higher intrinsic quality factors and easily processed multipacting conditions. The cavity characteristics, such as pressure sensitivity and Lorentz force detuning, were studied using ANSYS before the fabrication. These characteristics were measured during the cavity test. The comparison between the simulation and the measurement provides insight how the simulation can be used for design and fabrication of future cavities.

43 PARTICLE ACCELERATORS↗

Sample Results From The Extraction, Scrub, And Strip Test For The Blended NGS Solvent

This report summarizes the results of the extraction, scrub, and strip testing for the September 2013 sampling of the Next Generation Solvent (NGS) Blended solvent from the Modular Caustic Side-Solvent Extraction Unit (MCU) Solvent Hold Tank. MCU is in the process of transitioning from the BOBCalixC6 solvent to the NGS Blend solvent. As part of that transition, MCU has intentionally created a blended solvent to be processed using the Salt Batch program. This sample represents the first sample received from that blended solvent. There were two ESS tests performed where NGS blended solvent performance was assessed using either the Tank 21 material utilized in the Salt Batch 7 analyses or a simulant waste material used in the V-5/V-10 contactor testing. This report tabulates the temperature corrected cesium distribution, or D Cs values, step recovery percentage, and actual temperatures recorded during the experiment. This report also identifies the sample receipt date, preparation method, and analysis performed in the accumulation of the listed values. The calculated extraction D Cs values using the Tank 21H material and simulant are 59.4 and 53.8, respectively. The DCs values for two scrub and three strip processes for the Tank 21 material are 4.58, 2.91, 0.00184, 0.0252, and 0.00575, respectively. The D-values for two scrub and three strip processes for the simulant are 3.47, 2.18, 0.00468, 0.00057, and 0.00572, respectively. These values are similar to previous measurements of Salt Batch 7 feed with lab-prepared blended solvent. These numbers are considered compatible to allow simulant testing to be completed in place of actual waste due to the limited availability of feed material.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Final Report: LAW Glass Testing and VHT Model Assessment, VSL-08R1410-1, Rev 0

This report presents the results from the Low Activity Waste (LAW) glass formulation development and testing performed at the Vitreous State Laboratory (VSL) of the Catholic University of America (CUA) from October 2007 to August 2008. The work focused on certain aspects of qualification of LAW glasses for disposal in the Hanford Integrated Disposal Facility (IDF). One focus area was crystallization of LAW glasses containing less than 13.5 wt% and about 13.5 to 17.0 wt% Na 2 O, and the effect of crystallization on the behavior of these glasses on the Vapor Hydration Test (VHT) and the Product Consistency Test (PCT). Another area of interest was the performance on VHT of LAW glasses containing about 21 wt% or more of alkali oxides, and the variability in the VHT alteration rates. The VHT data were reviewed and analyzed to identify potential new approaches to modeling the relationship between VHT alteration rates and glass compositions.

36 MATERIALS SCIENCE↗

OC6 project Phase IV: validation of numerical models for novel floating offshore wind support structures

Abstract. This paper provides a summary of the work done within Phase IV of the Offshore Code Comparison Collaboration, Continued with Correlation and unCertainty (OC6) project, under International Energy Agency Wind Technology Collaboration Programme Task 30. This phase focused on validating the loading on and motion of a novel floating offshore wind system. Numerical models of a 3.6 MW horizontal-axis wind turbine atop the TetraSpar floating support structure were compared using measurement data from a 1:43-Froude-scale test performed in the University of Maine's Alfond Wind–Wave (W2) Ocean Engineering Laboratory. Participants in the project ran a series of simulations, including system equilibrium, surge offsets, free-decay tests, wind-only conditions, wave-only conditions, and a combination of wind and wave conditions. Validation of the models was performed by comparing the aerodynamic loading, floating support structure motion, tower base loading, mooring line tensions, and keel line tensions. The results show a relatively good estimation of the aerodynamic loading and a reasonable estimation of the platform motion and tower base fore–aft bending moment. However, there is a significant dispersion in the dynamic loading for the upwind mooring line. Very good agreement was observed between most of the numerical models and the experiment for the keel line tensions.

17 WIND ENERGY↗

Laser Powder Bed Fusion Manufactured Alloys 625 and 282 and Properties Relevant to Advanced Nuclear Components

Under the Advanced Materials and Manufacturing Technologies program, two Ni-based alloys fabricated by laser powder bed fusion (LPBF) have been evaluated: γ′-strengthened Haynes 282 and solution-strengthened Inconel 625. Large printing defects were observed in the LPBF 282 alloy fabricated using a Renishaw AM250 machine, likely due to particle spattering during printing. Annealing at 1,180°C for 1 h followed by 4 h at 800°C in a high density of 50 nm γ′-strengthening precipitates as well as partial recrystallization resulted in a bimodal grain distribution. Creep testing performed at 750°C revealed lower creep life and ductility for the LPBF 282 compared with wrought 282. X-ray computed tomography combined with optical and scanning electron microscopy microstructural characterization revealed crack formation during creep testing, initiated either from printing defects or from creep cavitation at grain boundaries. Printing defects were the likely reason for the lower creep performance of LPBF 282 and could be suppressed by optimizing the build configuration. Printing 625 on an EOS M290 machine using the recommended EOS parameters resulted in a very low defect density. Superior creep strength at 725°C was observed for the as-printed LPBF 625 along the build direction when compared with wrought 625. No defect larger than ~50 µm could be detected by X-ray computed tomography in the as-printed conditions and after creep testing for 1,000 h at 725°C and 150 MPa. Small, needle-like δ-phase precipitates were observed after creep testing for 100 h at 725°C and 200 MPa. The rapid formation of the γ phase is directly related to the initial Nb and Mo segregation in the LPBF 625 cell walls, and its effect on the alloy’s high-temperature performance will be evaluated. Solution annealing was carried out at 1,150°C for 1 h and led to full recrystallization of the alloy. A decrease in strength and increase in ductility were observed after solution annealing, and the alloy recrystallization resulted in isotropic tensile properties at room temperature, contrary to what was observed for the as-printed LPBF 625.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Weather aging effects on modified asphalt with rubber-polyethylene composites

Weather aging may cause more severe degradation on asphalt than thermal-oxidative aging due to the synergistic effect among oxygen, heat, ultraviolet (UV) radiation, and moisture. This study aimed to investigate weather aging effects and anti-aging mechanisms on asphalt modified with rubber-polyethylene (PE) composites. The modified binder blends and asphalt mixtures were subjected to outdoor weather aging. Dynamic shear rheometer (DSR), Fourier transform infrared spectroscopy (FTIR), Gel permeation chromatography (GPC), and optical microscopy tests were adopted to characterize the rheological properties, aging resistance, polymer degradation, and anti-aging mechanisms of modified binder blends, respectively. Mixture performance tests including Asphalt Pavement Analyzer (APA) and Ideal-CT tests were used to evaluate rutting and cracking resistance of asphalt mixtures. Results showed that weather aging can cause more severe aging to asphalt binders than pressure aging vessel (PAV) due to the severe degradation of PE particles. Rubber-PE composites alloyed with an extruder proved to stabilize PE particles in asphalt and significantly improve the aging resistance of modified binder blends. Furthermore, the enhanced aging resistance is attributed to the dispersion of PE particles and carbon black released by soluble rubbers.

Aging resistance↗

ASSESSING THE SIGNIFICANCE OF APPARENT CORRELATIONS BETWEEN RADIO AND GAMMA-RAY BLAZAR FLUXES

Whether or not a correlation exists between the radio and gamma-ray flux densities of blazars is a long-standing question, and one that is difficult to answer confidently because of various observational biases, which may either dilute or apparently enhance any intrinsic correlation between radio and gamma-ray luminosities. We introduce a novel method of data randomization to evaluate quantitatively the effect of these biases and to assess the intrinsic significance of an apparent correlation between radio and gamma-ray flux densities of blazars. The novelty of the method lies in a combination of data randomization in luminosity space (to ensure that the randomized data are intrinsically, and not just apparently, uncorrelated) and significance assessment in flux space (to explicitly avoid Malmquist bias and automatically account for the limited dynamical range in both frequencies). The method is applicable even to small samples that are not selected with strict statistical criteria. For larger samples we describe a variation of the method in which the sample is split in redshift bins, and the randomization is applied in each bin individually; this variation is designed to yield the equivalent to luminosity-function sampling of the underlying population in the limit of very large, statistically complete samples. We show that for a smaller number of redshift bins, the method yields a worse significance, and in this way it is conservative: although it may fail to confirm an existing intrinsic correlation in a small sample that cannot be split into many redshift bins, it will not assign a stronger, artificially enhanced significance. We demonstrate how our test performs as a function of number of sources, strength of correlation, and number of redshift bins used, and we show that while our test is robust against common-distance biases and associated false positives for uncorrelated data, it retains the power of other methods in rejecting the null hypothesis of no correlation for correlated data.

79 ASTRONOMY AND ASTROPHYSICS↗

Towards the construction of the Mu2e electromagnetic calorimeter at Fermilab

Mu2e will search for the Charge Lepton Flavor Violating (CLFV) conversion of a muon into an electron in the field of a nucleus. A clean discovery signature is provided by the mono-energetic conversion electron (E e = 104.96 MeV). If no events are observed, Mu2e will set a limit on the ratio between the conversion and the nuclear capture rate below 3 × 10$^{-17}$ (at 90% C.L.). In order to confirm that the observed candidate is an electron, the calorimeter resolution requirements are to provide E res < 10%, T res < 500 ps for 100 MeV electrons while working in vacuum and in a high radiation environment and high magnetic field. The calorimeter is made of two annular aluminum disks, each one filled with 674 pure CsI crystals read out by SiPMs. A sophisticated mechanics and cooling system has been developed to support the crystals and cool the sensors. Radiation hard analog and fast digital electronics have been developed. In this paper the QC tests performed on the produced components and the construction status are reported, as well as the results obtained on the large size prototype with test beam data and at a cosmic ray test stand.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Experimental Studies of Graphene-Coated Polymer Electrolyte Membranes for Direct Methanol Fuel Cells

The two main technical limitations of direct methanol fuel cells (DMFCs) are the slow kinetic reactions of the methanol oxidation reaction (MOR) in the anode and the crossing over of unreacted methanol through the proton exchange membrane (PEM). It is a common practice to use Nafion membranes as PEMs, which have high ion exchange capacity. However, Nafion-based membranes also have high fuel permeability, decreasing fuel utilization, and reducing the potential power density. This article focuses on using graphene-coated (Gr-coated) PEMs to reduce fuel crossover. Protons can permeate across graphene, and thus, it can be employed in various devices as a proton conductive membrane. Here, we report the efficiency of Gr-coated Nafions. We tested performance and crossover at three different temperatures with four different fuel concentrations and compared it to a Nafion PEM that underwent the same test conditions. We found that the adhesion of Gr on to PEMs is insufficient for prolonging fuel cell operation, resulting in Gr delamination at high temperatures and higher fuel crossover values compared to lower temperature testing. Furthermore, the results for 7.5M methanol fuel show a reduction of up to 25% in methanol crossover, translating to a peak power density that increases from 3.9 to 9.5 mW/cm 2 when using a Gr-coated PEM compared to a Nafion PEM at 30 °C.

25 ENERGY STORAGE↗

METAL MEDIA FILTERS, AG-1 SECTION FI

One application of metal media filters is in various nuclear air cleaning processes including applications for protecting workers, the public and the environment from hazardous and radioactive particles. To support this application the development of the ASME AG-1 FI Standard on Metal Media has been under way for more than ten years. Development of the proposed section has required resolving several difficult issues associated with operating conditions (media velocity, pressure drop, etc.), qualification testing, and quality acceptance testing. Performance characteristics of metal media are dramatically different than the glass fiber media with respect to parameters like differential pressures, operating temperatures, media strength, etc. These differences make existing data for a glass fiber media inadequate for qualifying a metal media filter for AG-1. In the past much work has been conducted on metal media filters at facilities such as Lawrence Livermore National Laboratory (LLNL) and Savannah River National Laboratory (SRNL) to qualify the media as High Efficiency Particulate Air (HEPA) Filters. Particle retention testing has been conducted at Oak Ridge Filter Test Facility and at Air Techniques International (ATI) to prove that the metal media meets or exceeds the 99.97% particle retention required for a HEPA Filter. Even with his testing, data was lacking to complete an AG-1 FI Standard on metal media. With funding secured by Mississippi State University (MSU) from National Nuclear Security Administration (NNSA), a research test stand is being designed and fabricated at MSU's Institute for Clean Energy Technology (ICET) Facility to obtain qualification data on metal media. This in turn will support required data needed for the FI Standard. The paper will discuss in detail how the test stand at MSU will obtain the necessary data to complete the FI Standard.

42 ENGINEERING↗

High-Surface-Area Inorganic Membrane for Process Water Removal: Application to Ethanol Fuel Production

This report summarizes process research results about concept development of thin flat sheet water-selective molecular sieve membrane – a breakthrough membrane product technology for separation of water from ethanol-enriched process streams. The studies include 1) membrane separation performance testing with real-world feeds sampled from Pacific Ethanol Inc’s ethanol plant at Boardman, Oregon and 2) process design and simulation of membrane separation implementation into a corn ethanol plant. The separation tests were conducted on a laboratory-bench testing apparatus in a batch operation mode with small membrane samples (about 1-inch diameter) but under practical conditions, while the process simulation was performed using ASPEN and USDA models. A two-stage membrane separation system is proposed to conduct ethanol enrichment and purification by replacing respective distillation and adsorption process. More than 90% energy saving can be obtained using the membrane separation. It is estimated that the membrane unit for a 40 million gal/year of ethanol plant can be fairly compact - about the sizes of a plate heat exchanger due to high flux of the new membrane. The cost and lifetime of this new membrane product are critical factors to lower the capital cost. This membrane technology is promising for upgrading of existing corn ethanol plants and for building of new cellulosic ethanol plants in the future as well. The results obtained in this work warrant further development of membrane module prototypes and demonstration of their long-term operation stability with slip streams at ethanol plants, which is necessary to move the technology toward commercialization.

09 BIOMASS FUELS↗

Sensor Qualification for the Development of Advanced Reactors

A temperature sensor qualification device is undergoing development and testing in order to qualify temperature sensors for advanced reactor metrology applications. This device will provide National Institute of Standards and Technology (NIST) traceable performance testing of temperature sensors while under the high radiation environments experienced while in-core. This is completed by utilizing retractable sensors which transfer the measurements from ex-core to in-core sensors. A detailed discussion of the uncertainty propagation associated with this comparative process is provided. Experimental testing of the temperature distribution occurring in the device has begun and is reported on. It is pertinent to minimize this temperature distribution to prevent variation in sensor measurements. This variation will be indistinguishable from sensor drift for in-pile applications and would result in unnecessarily conservative uncertainty bounds.

46 - INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AN↗