Results for “Performance benchmark” — Page 42

NASA NTRS2003

Comment on 'Modeling of Convective-Stratiform Precipitation Processes: Sensitivity to Partitioning Methods' by Matthias Steiner

Despite the obvious notion that the presence of hail or graupel is a good indication of convection, the model results show this does not provide an objective benchmark partly due to the unrealistic presence of small amounts of hail or graupel throughout the anvil in the model but mainly because of the significant amounts of hail or graupel, especially in the tropical TOGA COARE simulation, in the transition zone. Without use of a "transition" category, it is open to debate as how this region should best be defined, as stratiform or as convective. So, the presence of significant hail or graupel contents in this zone significantly degrades its use an objective benchmark for convection. The separation algorithm comparison was done in the context of a cloud-resolving model. These models are widely used and serve a variety of purposes especially with regard to retrieving information that cannot be directly measured by providing synthetic data sets that are consistent and complete. Separation algorithms are regularly applied in these models. However, as with any modeling system, these types 'of models are constantly being improved to overcome any known deficiencies and make them more accurate representations of observed systems. The presence of hail and graupel in the anvil and the bias towards heavy rainfall rates are two such examples of areas that need improvement. Since, both of these can effect the perceived performance of the separation algorithms, the Lang et al. (2003) study did not want to overstate the relative performance of any specific algorithms.

Lang, Steve↗

NASA NTRSDate not supplied

Benchmark Problem for Autonomous Urban Air Mobility

This paper introduces a Community Benchmark Problem (CBP) for Intelligent Contingency Management (ICM) for Urban Air Mobility (UAM) aircraft. The CBP aims to provide a common framework for measuring and comparing the progress of autonomy solutions for UAM aircraft in handling emergency situations. The paper proposes a methodology for defining and quantifying five measures of complexity that capture the challenges and requirements of ICM for UAM: Mission, Environmental, Autonomy, Decision-Making, and Mission Fault. In addition, it proposes a methodology for defining and quantifying mission risk acceptability with the same goals: Contingency Management, Mission Success, Operational, Mission Redefinition, and Environmental. We describe how to use these measures to track progress of the development of ICM capability, as well as to create scenarios and evaluate the performance of different autonomy solutions.

autonomy↗

NASA NTRSDate not supplied

Community Benchmark Problem for Intelligent Contingency Management

This paper introduces a Community Benchmark Problem (CBP) for Intelligent Contingency Management (ICM) for Urban Air Mobility (UAM) aircraft. The CBP aims to provide a common framework for measuring and comparing the progress of autonomy solutions for UAM aircraft in handling emergency situations. The paper proposes a methodology for defining and quantifying five measures of complexity that capture the challenges and requirements of ICM for UAM: Mission, Environmental, Autonomy, Decision-Making, and Mission Fault. In addition, it proposes a methodology for defining and quantifying mission risk acceptability with the same goals: Contingency Management, Mission Success, Operational, Mission Redefinition, and Environmental. We describe how to use these measures to track progress of the development of ICM capability, as well as to create scenarios and evaluate the performance of different autonomy solutions.

autonomy↗

NASA NTRSDate not supplied

Traffic Prediction for Uncommunicative Aircraft in Terminal Airspace: Development Framework and Performance Evaluations

This paper presents an air traffic prediction algorithm that takes observations of an aircraft and classifies aircraft type, estimates the aircraft's intent to and method of joining an airport traffic pattern, and predicts the aircaft's future trajectory. To develop algorithms that enable autonomous aircraft to safely insert into un-towered traffic patterns, several challenges need to be addressed. These challenges range from traffic detection to sensor fusion to own-ship trajectory replanning. Critical to a trajectory replanning algorithm is information regarding the future behavior of all traffic aircraft in the operational environment. The presented traffic prediction algorithm generates this information using regular measurements of traffic aircraft position and velocity to classify the aircraft by speed-class, estimate how the aircraft will approach the runway, and construct a predicted trajectory to the runway including future positions and velocities at specific times. The predictions of the presented algorithm are the necessary inputs for any downstream traffic pattern sequencing and own-ship trajectory planning routines. The presented algorithm is benchmarked using approximately 300 randomized traffic trajectories, spanning four vehicle weight classes and eight traffic entry types. While the algorithm can process multiple traffic vehicles in the terminal area, there is no prediction of traffic-on-traffic interaction. Each traffic vehicle is processed separately.

John D McMinn↗

NASA NTRS2005

Cold Flow Plume Entrainment Test Final Report NTF Test Number 2456

As part of the Space Shuttle Return to Flight (RTF) program, Marshall Space Flight Center (MSFC) performed computational fluid dynamics (CFD) analysis to define the velocity flowfields around the Shuttle stack at liftoff. These CFD predicted velocity flowfields were used in debris transport analysis (DTA). High speed flows such as plumes induce or 'entrain' mass from the surrounding environment. Previous work had shown that CFD analysis over-predicts plume induced flows. Therefore, the DTA would tend to 1) predict more debris impacts, and 2) the debris velocity (and kinetic energy) of those impacts would be too high. At a November, 2004 peer-review it was recommended that the Liftoff DTA team quantify the uncertainty in the DTA caused by the CFD's over prediction of plume induced flow. To do so, the Liftoff DTA team needed benchmark quality data for plume induced flow to quantify the CFD accuracy and its effect on the DTA. MSFC's Nozzle Test Facility (NTF) conducted the "Nozzle Induced Flows test, P#2456" to obtain experimental data for plume induced flows for nozzle flow exhausting into q quiescent freestream. Planning for the test began in December, 2004 and the experimental data was obtained in February and March of 2005. The funding for this test was provided by MSFC's Space Shuttle Propulsion Systems Integration and Engineering office.

Ruf, Joseph H.↗

NASA NTRS1983

Aerothermal modeling, phase 1. Volume 1: Model assessment

Phase 1 was conducted as part of the overall NASA Hot Section Technology (HOST) Program. The purpose of this effort was to determine the predictive accuracy of and the deficiencies within the various analytical modules comprising the overall combustor aerothermal model used at General Electric, as well as to formulate recommendations for improvement where needed. This effort involved the assembly of a benchmark quality data base from selected available literature, and from General Electric engine and combustor component test data. This data base was supplemented with additional definitive data obtained from an experimental test program conducted as part of the Phase 1 effort. Using selections from this data base, assessment studies were conducted to evaluate the various modules. Assessment of the internal flow module was conducted using 2-D parabolic and ellipitic, as well as 3-D elliptic internal flow calculations of definitive test data selected from the assembled data base. The 2-D assessment provided methodical examination of the mathematical techniques and the physical submodules, while the 3-D assessment focused on usefulness as a design tool. Calculations of combustor linear metal temperatures, pressure loss performance, and airflow distribution were performed using aerothermal modules which were in general use for many years at General Electric. The results of these assessment provided for the identification of deficiencies within the modules. The deficiencies were addressed in some detail providing a foundation on which to formulate a prioritized list of recommendations for improvement.

Kenworthy, M. J.↗

NASA NTRS1999

Transonic Flutter Suppression Control Law Design Using Classical and Optimal Techniques with Wind-Tunnel Results

The benchmark active controls technology and wind tunnel test program at NASA Langley Research Center was started with the objective to investigate the nonlinear, unsteady aerodynamics and active flutter suppression of wings in transonic flow. The paper will present the flutter suppression control law design process, numerical nonlinear simulation and wind tunnel test results for the NACA 0012 benchmark active control wing model. The flutter suppression control law design processes using (1) classical, (2) linear quadratic Gaussian (LQG), and (3) minimax techniques are described. A unified general formulation and solution for the LQG and minimax approaches, based on the steady state differential game theory is presented. Design considerations for improving the control law robustness and digital implementation are outlined. It was shown that simple control laws when properly designed based on physical principles, can suppress flutter with limited control power even in the presence of transonic shocks and flow separation. In wind tunnel tests in air and heavy gas medium, the closed-loop flutter dynamic pressure was increased to the tunnel upper limit of 200 psf. The control law robustness and performance predictions were verified in highly nonlinear flow conditions, gain and phase perturbations, and spoiler deployment. A non-design plunge instability condition was also successfully suppressed.

Mukhopadhyay, Vivek↗

NASA NTRS1999

Transonic Flutter Suppression Control Law Design, Analysis and Wind Tunnel Results

The benchmark active controls technology and wind tunnel test program at NASA Langley Research Center was started with the objective to investigate the nonlinear, unsteady aerodynamics and active flutter suppression of wings in transonic flow. The paper will present the flutter suppression control law design process, numerical nonlinear simulation and wind tunnel test results for the NACA 0012 benchmark active control wing model. The flutter suppression control law design processes using (1) classical, (2) linear quadratic Gaussian (LQG), and (3) minimax techniques are described. A unified general formulation and solution for the LQG and minimax approaches, based on the steady state differential game theory is presented. Design considerations for improving the control law robustness and digital implementation are outlined. It was shown that simple control laws when properly designed based on physical principles, can suppress flutter with limited control power even in the presence of transonic shocks and flow separation. In wind tunnel tests in air and heavy gas medium, the closed-loop flutter dynamic pressure was increased to the tunnel upper limit of 200 psf The control law robustness and performance predictions were verified in highly nonlinear flow conditions, gain and phase perturbations, and spoiler deployment. A non-design plunge instability condition was also successfully suppressed.

Mukhopadhyay, Vivek↗

NASA NTRS1999

Transonic Flutter Suppression Control Law Design, Analysis and Wind-Tunnel Results

The benchmark active controls technology and wind tunnel test program at NASA Langley Research Center was started with the objective to investigate the nonlinear, unsteady aerodynamics and active flutter suppression of wings in transonic flow. The paper will present the flutter suppression control law design process, numerical nonlinear simulation and wind tunnel test results for the NACA 0012 benchmark active control wing model. The flutter suppression control law design processes using (1) classical, (2) linear quadratic Gaussian (LQG), and (3) minimax techniques are described. A unified general formulation and solution for the LQG and minimax approaches, based on the steady state differential game theory is presented. Design considerations for improving the control law robustness and digital implementation are outlined. It was shown that simple control laws when properly designed based on physical principles, can suppress flutter with limited control power even in the presence of transonic shocks and flow separation. In wind tunnel tests in air and heavy gas medium, the closed-loop flutter dynamic pressure was increased to the tunnel upper limit of 200 psf. The control law robustness and performance predictions were verified in highly nonlinear flow conditions, gain and phase perturbations, and spoiler deployment. A non-design plunge instability condition was also successfully suppressed.

Mukhopadhyay, Vivek↗

NASA NTRS1999

Transonic Flutter Suppression Control Law Design Using Classical and Optimal Techniques with Wind-Tunnel Results

The benchmark active controls technology and wind tunnel test program at NASA Langley Research Center was started with the objective to investigate the nonlinear, unsteady aerodynamics and active flutter suppression of wings in transonic flow. The paper will present the flutter suppression control law design process, numerical nonlinear simulation and wind tunnel test results for the NACA 0012 benchmark active control wing model. The flutter suppression control law design processes using (1) classical, (2) linear quadratic Gaussian (LQG), and (3) minimax techniques are described. A unified general formulation and solution for the LQG and minimax approaches, based on the steady state differential game theory is presented. Design considerations for improving the control law robustness and digital implementation are outlined. It was shown that simple control laws when properly designed based on physical principles, can suppress flutter with limited control power even in the presence of transonic shocks and flow separation. In wind tunnel tests in air and heavy gas medium, the closed-loop flutter dynamic pressure was increased to the tunnel upper limit of 200 psf. The control law robustness and performance predictions were verified in highly nonlinear flow conditions, gain and phase perturbations, and spoiler deployment. A non-design plunge instability condition was also successfully suppressed.

Mukhopadhyay, Vivek↗

NASA NTRSDate not supplied

ANALYSIS OF THE MSL/MEDLI ENTRY DATA WITH COUPLED CFD AND MATERIAL RESPONSE.

The Mars Science Laboratory (MSL) was protected during its atmospheric entry by an instrumented heat-shield using NASA's Phenolic Impregnated Carbon Ablator (PICA) material. PICA is a lightweight carbon fiber/polymeric resin material that offers out-standing performances for protecting probes during planetary entry. The Mars Entry Descent and Landing Instrument (MEDLI) suite on MSL offers unique in-flight validation data for models of material response and atmospheric entry. MEDLI recorded, among other things, time-resolved in-depth temperature data of PICA using thermocouple sensors assembled in the MEDLI Integrated Sensor Plugs (MISP). The objective of this work is to showcase and analyze the coupling between the material response and the aerothermal environment. As shown in Figure 1, the workflow is divided into the following steps. First, the aerothermal properties are computed in the Data Parallel Line Relaxation (DPLR) code [3] and used with the Nonequilibrium air radiation (NEQAIR) program [8] to compute radiative heating. Second, the thermal response inside the material is computed in the Porous material Analysis Toolbox based on Open-FOAM (PATO) using a fixed blowing correction parameter. Third, the pyrolysis gases computed in PATO are used as inputs to a blowing boundary condition within DPLR. Fourth, the new environment properties from DPLR are used in NEQAIR to provide an updated solution, then both the updated aerothermal environment and radiative heating are used in PATO without blowing correction. The third and fourth steps are then repeated until convergence in surface temperature is obtained. Convergence in the radiative heating is generally achieved before surface temperature, at which point the radiative heating is no longer updated. Char mass loss rates are forced to zero to produce a non-receding surface condition. For early time points in the trajectory, where flow around the MSL aeroshell is rarefied, the Direct Simulation Monte Carlo (DSMC) code, SPARTA, is used to compute the aerothermal environment. Iteration between PATO and SPARTA is not performed due to the computational cost of DSMC simulations. Preliminary results of the coupling between PATO and DPLR for the MSL heatshield atmospheric entry model are presented in Figures 2-4 at 65 seconds after entry interface. Figure 2 shows the surface temperature results from an uncoupled simulation in PATO with the blowing correction parameter applied (left) along with the coupled surface temperature after iteration (right). Figure 3 shows the surface temperature along the centerline from windward to leeward for easier comparison. Figure 4 shows the coupled and uncoupled pyrolysis gas blowing rate. Mars 2020 used a similar heatshield consisting of PICA for thermal protection during entry, descent, and landing. In preparation for Mars 2020 post-flight analysis, the predictive material response capability is benchmarked against flight data from MEDLI. This work represents an important milestone toward the development of validated predictive capabilities for designing thermal protection systems for planetary probes.

Mars Science Laboratory↗

NASA NTRSDate not supplied

Analysis of MSL/MEDLI Entry Data with Coupled CFD and Material Response

The Mars Science Laboratory (MSL) was protected during its atmospheric entry by an instrumented heatshield using NASA's Phenolic Impregnated Carbon Ablator (PICA) material [1]. PICA is a lightweight carbon fiber/polymeric resin material that offers outstanding performances for protecting probes during planetary entry. The Mars Entry Descent and Landing Instrument (MEDLI) suite on MSL offers unique in-flight validation data for models of material response and atmospheric entry. MEDLI recorded, among other things, time-resolved in-depth temperature data of PICA using thermocouple sensors assembled in the MEDLI Integrated Sensor Plugs (MISP) [2]. The objective of this work is to showcase and analyze the coupling between the material response and the aerothermal environment. As shown in Figure 1, the workflow is divided into the following steps. First, the aerothermal properties are computed in the Data Parallel Line Relaxation (DPLR) code [3] and used with the Nonequilibrium air radiation (NEQAIR) program [8] to compute radiative heating. Second, the thermal response inside the material is computed in the Porous material Analysis Toolbox based on OpenFOAM (PATO) [4,5,6] using a fixed blowing correction parameter. Third, the pyrolysis gases computed in PATO are used as inputs to a blowing boundary condition within DPLR. Fourth, the new environment properties from DPLR are used in NEQAIR to provide an updated solution, then both the updated aerothermal environment and radiative heating are used in PATO without blowing correction. The third and fourth steps are then repeated until convergence in surface temperature is obtained. Convergence in the radiative heating is generally achieved before surface temperature, at which point the radiative heating is no longer updated. Char mass loss rates are forced to zero to produce a non-receding surface condition. For early time points in the trajectory, where flow around the MSL aeroshell is rarefied, the Direct Simulation Monte Carlo (DSMC) code, SPARTA [7], is used to compute the aerothermal environment. Iteration between PATO and SPARTA is not performed due to the computational cost of DSMC simulations. Preliminary results of the coupling between PATO and DPLR for the MSL heatshield atmospheric entry model are presented in Figures 2-4 at 65 seconds after entry interface. Figure 2 shows the surface temperature results from an uncoupled simulation in PATO with the blowing correction parameter applied (left) along with the coupled surface temperature after iteration (right). Figure 3 shows the surface temperature along the centerline from windward to leeward for easier comparison. Figure 4 shows the coupled and uncoupled pyrolysis gas blowing rate. Mars 2020 used a similar heatshield consisting of PICA for thermal protection during entry, descent, and landing. In preparation for Mars 2020 post-flight analysis, the predictive material response capability is benchmarked against flight data from MEDLI. This work represents an important milestone toward the development of validated predictive capabilities for designing thermal protection systems for planetary probes.

Thermal Protection Systems↗

NASA NTRS1995

Application of essentially nonoscillatory methods to aeroacoustic flow problems

A finite-difference essentially nonoscillatory (ENO) method has been applied to several of the problems prescribed for the workshop sponsored jointly by the Institute for Computer Applications in Science and Engineering and by NASA Langley Research Center entitled 'Benchmark Problems in Computational Aeroacoustics'. The workshop focused on computational challenges specific to aeroacoustics. Among these are long-distance propagation of a short-wavelength disturbance, propagation of small-amplitude disturbances, and nonreflective boundary conditions. The shock capturing-capability inherent to the ENO method effectively eliminates oscillations near shock waves without the need to add and tune dissipation or filter terms. The method-of-lines approach allows the temporal and spatial operators to be chosen separately in accordance with the demands of a particular problem. The ENO method was robust and accurate for all problems in which the propagating wave was resolved with 8 or more points per wavelength. The finite-wave-model boundary condition, a local nonlinear acoustic boundary condition, performed well for the one-dimensional problems. The buffer-domain approach performed well for the two-dimensional test problem. The amplitude of nonphysical reflections were less than 1 percent of the exiting wave's amplitude.

Atkins, Harold L.↗

NASA NTRS1993

Numerical analysis of base flowfield at high altitude for a four-engine clustered nozzle configuration

The objective of this study is to benchmark a four-engine clustered nozzle base flowfield with a computational fluid dynamics (CFD) model. The CFD model is a pressure based, viscous flow formulation. An adaptive upwind scheme is employed for the spatial discretization. The upwind scheme is based on second and fourth order central differencing with adaptive artificial dissipation. Qualitative base flow features such as the reverse jet, wall jet, recompression shock, and plume-plume impingement have been captured. The computed quantitative flow properties such as the radial base pressure distribution, model centerline Mach number and static pressure variation, and base pressure characteristic curve agreed reasonably well with those of the measurement. Parametric study on the effect of grid resolution, turbulence model, inlet boundary condition and difference scheme on convective terms has been performed. The results showed that grid resolution and turbulence model are two primary factors that influence the accuracy of the base flowfield prediction.

Wang, Ten-See↗

NASA NTRS2005

Supporting Development for the Stirling Radioisotope Generator and Advanced Stirling Technology Development at NASA Glenn Research Center

A high-efficiency, 110-We (watts electric) Stirling Radioisotope Generator (SRG110) for possible use on future NASA Space Science missions is being developed by the Department of Energy, Lockheed Martin, Stirling Technology Company (STC), and NASA Glenn Research Center (GRC). Potential mission use includes providing spacecraft onboard electric power for deep space missions and power for unmanned Mars rovers. GRC is conducting an in-house supporting technology project to assist in SRG110 development. One-, three-, and six-month heater head structural benchmark tests have been completed in support of a heater head life assessment. Testing is underway to evaluate the key epoxy bond of the permanent magnets to the linear alternator stator lamination stack. GRC has completed over 10,000 hours of extended duration testing of the Stirling convertors for the SRG110, and a three-year test of two Stirling convertors in a thermal vacuum environment will be starting shortly. GRC is also developing advanced technology for Stirling convertors, aimed at substantially improving the specific power and efficiency of the convertor and the overall generator. Sunpower, Inc. has begun the development of a lightweight Stirling convertor, under a NASA Research Announcement (NRA) award, that has the potential to double the system specific power to about 8 We/kg. GRC has performed random vibration testing of a lower-power version of this convertor to evaluate robustness for surviving launch vibrations. STC has also completed the initial design of a lightweight convertor. Status of the development of a multi-dimensional computational fluid dynamics code and high-temperature materials work on advanced superalloys, refractory metal alloys, and ceramics are also discussed.

Thieme, Lanny G.↗

NASA NTRS2019

Response Versus Scan-Angle Assessment of MODIS Reflective Solar Bands in Collection 6.1 Calibration

The Moderate Resolution Imaging Spectroradiometer (MODIS) instruments onboard the Aqua and Terra satellites have been operated for nearly two decades, producing high-quality earth observation data sets suitable for a broad range of scientific studies regarding the earth’s land, ocean, and atmospheric processes. The high radiometric accuracy of MODIS reflective solar band (RSB) calibration has also served as benchmark measurements for on-orbit cross-calibration studies. As the two MODIS instruments have operated well beyond their design lifespan of six years, the measurements from the onboard calibrators alone become inadequate to characterize the sensor’s response at all scan angles, as evinced by long-term drifts observed at certain scan positions of the Aqua-MODIS 0.64- and 0.86-μm bands in Collection 6 (C6) data set. The latest MODIS Level 1B C6.1 data set incorporates earth-view response trending from invariant desert sites as supplemental inputs to characterize the scan-angle calibration dependencies for all RSB. This article presents a deep convective cloud (DCC)-based calibration approach for an independent evaluation of the MODIS RSB response versus scan-angle (RVS) performance in C6.1. The long-term calibration stability and RVS differences in C6.1 have been significantly improved for Aqua-MODIS RSB. The observed RVS differences of more than 2% in Aqua-MODIS C6 bands 1 and 2 have been reduced to within 1% in C6.1. Some RSBs of Terra-MODIS have suffered temporal drifts up to ~2% and calibration shifts up to 3%, particularly around 2016 when the Terra satellite entered into safe mode. The DCC approach has been found very effective in tracking the on-orbit RVS changes over time.

Clouds and the Earth’s Radiant Energy System (CERE↗

NASA NTRS2022

Evaluating Network Performance of Containerized Test Framework for Distributed Space Systems

Distributed space systems are a mission architecture consisting of multiple spacecraft as a cohesive system which provide multipoint sampling, increased mission coverage, or improved sample resolution, while reducing mission risk through redundancy. To fully realize the potential of these systems, eventually scaling to hundreds or thousands of spacecraft, distributed space systems need to be operated as a single entity, which will enable a variety of novel scientific space missions. The Distributed Spacecraft Autonomy (DSA) project is a software project which aims to mature the technology needed for those systems, namely autonomous decision-making and swarm networking. The DSA project leverages a containerized swarm test framework to simulate spacecraft software, which can identify emergent behavior early in development. Container virtualization allows distributed spacecraft systems to be simulated entirely in software on a single computer, avoiding the overhead associated with conventional approaches like hardware facsimiles and virtual machines. For this approach to be effective, the simulated system behavior must not be artificially influenced by the swarm test framework itself. To address this, we present a series of benchmarks to quantify virtual network bandwidth available on a single-host computer and contextualize this against the network and application behavior of the DSA swarm test framework.

Distributed Spacecraft Autonomy↗

NASA NTRS2021

Online Photometric Calibration of Automatic Gain Thermal Infrared Cameras

Thermal infrared cameras are increasingly being used in various applications such as robot vision, industrial inspection and medical imaging, thanks to their improved resolution and portability. However, the performance of traditional computer vision techniques developed for electro-optical imagery does not directly translate to the thermal domain due to two major reasons: these algorithms require photometric assumptions to hold, and methods for photometric calibration of RGB cameras cannot be applied to thermal-infrared cameras due to difference in data acquisition and sensor phenomenology. In this paper, we take a step in this direction, and introduce a novel algorithm for online photometric calibration of thermalinfrared cameras. Our proposed method does not require any specific driver/hardware support and hence can be applied to any commercial off-the-shelf thermal IR camera. We present this in the context of visual odometry and SLAM algorithms, and demonstrate the efficacy of our proposed system through extensive experiments for both standard benchmark datasets, and real-world field tests with a thermal-infrared camera in natural outdoor environments.

Daftry, Shreyansh↗