Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “OPTICAL REFLECTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42

Experiment M0003-4: Advanced solar cell and coverglass analysis, an overview

The experiment consists of 51 coverglass samples and 12 solar cell strings. Sixteen of the coverglass samples were on the leading edge and 16 on the trailing edge. An additional 16 samples were used as control samples and were not flown. The scenario for analysis was established for the coverglass. A photographic and Namarski survey were taken. Selected sites were then analyzed using surface analysis techniques. The coverglass samples are analyzed in their dirty condition for optical transmission, reflectance, and absorbance. The solar cells were visually inspected and photographed. Tape recorder data is analyzed and selected cell strings are evaluated for their electrical properties.

Trumble, Terry M.↗

Determination of the in-flight spectral and radiometric characteristics of the Airborne Visible/Infrared Imaging Spectrometer (AVIRIS)

AVIRIS is a science research imaging spectrometer that measures radiance in 224 channels between 400 to 2450 nm in the electromagnetic spectrum. To determine the inflight spectral and radiometric characteristics of AVIRIS a validation and calibration experiment was performed. Five data sets were acquired over a calibration site on the homogeneous playa of Rogers Dry Lake, California, U.S. Surface reflectance, atmospheric optical depths, and atmospheric water vapor measurements were acquired concurrently with the overflights. These in situ measurements were used to constrain the LOWTRAN 7 radiative transfer code to predict the total spectral radiance incident at the AVIRIS aperture. These predicted radiances and the AVIRIS measured radiances were analyzed to validate the inflight characteristics. Inflight spectral channel positions and response functions over the AVIRIS spectral range were derived. Radiometric calibration coefficients were calculated for each channel as well as radiometric accuracy, intraflight stability, and noise equivalent delta radiance.

Green, Robert O.↗

Spatial heterogeneity in vegetation canopies and remote sensing of absorbed photosynthetically active radiation - A modeling study

A 3D radiative transfer model is used to investigate the relationship between spectral indices and fraction of absorbed photosynthetically active radiation (PAR) in horizontally heterogeneous vegetation canopies. Canopy reflection at optical wavelengths and PAR absorption are simulated. Data obtained indicate that the leaf area index of a canopy is less of an instructive parameter than the ground cover and clump leaf area index for these canopies. It is found that the relationship between the normalized difference vegetation index and fraction of absorbed PAR is almost linear and independent of spatial heterogeneity.

Asrar, G.↗

Erosion rates for polymers measured on LDEF

The summary and viewgraphs of work presented at the Long Duration Exposure Facility (LDEF) materials workshop are given. Experimental data for erosion depths and rates for polymers measured on LDEF are given. In general, agreement is reasonably good between erosion rates from the University of Alabama in Huntsville (UAH) LDEF experiment and prior data obtained at much lower mission fluences. Agreement is particularly satisfying in the case of Kapton where the prior data base is large. In spite of the known presence of silicaceous contamination on LDEF surfaces, the erosion rates of the highly erodible materials are hardly affected, if at all. Graphs showing changes in optical properties (reflectance and transmittance) of metal films are included.

Gregory, John C.↗

Moderate Resolution Imaging Spectrometer-Tilt (MODIS-T) baseline concept

There will be several state of the art spectrometers in operation on the NASA Polar Orbiting Platform (NPOP-1) as part of the Earth Observing System (EOS). The Moderate Resolution Imaging Spectrometer (MODIS) will consist of two imaging spectroradiometric instruments, one nadir viewing (MODIS-N) and the other tiltable (MODIS-T) for ocean observation and land bidirectional reflectance studies. The Moderate Resolution Imaging Spectrometer-Tilt (MODIS-T) instrument is presently being constructed for flight on the EOS. It is an imaging spectrometer utilizing a grating type, reflecting Schmidt optical design that must provide a 1.1 kilometer spatial resolution at nadir from a spacecraft altitude of 705 kilometers with a 1500 kilometer cross-track swath and a +/- 50 degree forward and aft tilt capability. The instrument is required to cover the wavelength range from 400 to 880 nanometers in approximately 15 nanometer steps with less than 2.3 percent instrument induced polarization. The absolute radiometric accuracy must be at least 5 percent over the full dynamic range of the instrument.

Magner, Thomas J.↗

Origin of the Bandgap Bowing in ZNSe(1-x)Te(x) Alloys

Photomodulated reflection and optical absorption spectroscopies were used to measure the composition and hydrostatic pressure dependencies of interband optical transitions in ZnSe(1-x)Te(x) alloys. On the Te-rich side, the bandgap reduction and the reduction in the pressure dependence of the bandgap are well explained by the band anticrossing interaction between the ZnTe conduction band states and the Se localized state located at 2.85 eV above the valence band top of ZnTe. On the Se-rich side, an interaction between the degenerate Gamma valence bands of ZnSe and the localized Te state located at 0.1 eV above the valence band top of ZnSe is proposed to generate the bandgap reduction and the rapid increase of the spin-orbit splitting with increasing Te concentration. A linear interpolation between these two models accounts for the composition and pressure dependencies of the bandgap in the entire composition range.

Walukiewicz, W.↗

The X-ray Reflectors in the Nucleus of the Seyfert Galaxy NGC 1068

Based on observations of the Seyfert nucleus in NGC 1068 with ASCA, RXTE and BeppoSAX, we report the discovery of a flare (increase in flux by a factor of approximately 1.6) in the 6.7 keV Fe K line component between observations obtained four months apart, with no significant change in the other (6.21, 6.4, and 6.97 keV) Fe Kalpha line components. During this time, the continuum flux decreased by approximately 20%. The RXTE spectrum requires an Fe K absorption edge near 8.6 keV (Fe XXIII- XXV). The spectral data indicate that the 2-10 keV continuum emission is dominated (approximately 2/3 of the luminosity) by reflection from a previously unidentified region of warm, ionized gas located approximately or less than 0.2 pc from the AGN. The remaining approximately 1/3 of the observed X-ray emission is reflected from optically thick, neutral gas. The coronal gas in the inner Narrow-Line Region (NLR) and/or the cold gas at the inner surface of the obscuring 'torus' are possible cold reflectors. The inferred properties of the warm reflector are: size (diameter) approximately or less than 0.2 pc, gas density n approximately or greater than 10(exp 5.5)/cu cm, ionization parameter xi is approximately 10(exp 3.5) erg cm s(exp -1), and covering fraction 0.003 (L(sub 0)/ 10(exp 43.5) erg s(exp -1)(exp -1) less than (omega/4pi) less than 0.024 (L(sub 0)/ 10(exp 43.5) erg s(exp -1) (exp -1) where L(sub 0) is the intrinsic 2-10 keV X-ray luminosity of the AGN. We suggest that the warm reflector gas is the source of the (variable) 6.7 keV Fe line emission, and the 6.97 keV Fe line emission. The 6.7 keV line flare is assumed to be due to an increase in the emissivity of the warm reflector gas from a decrease (by 20-30%) in L(sub 0). The properties of the warm reflector are most consistent with an intrinsically X-ray weak AGN with L(sub 0) approximately equals 10(exp 43.0) erg s(exp -1). The optical and UV emission that scatters from the warm reflector into our line of sight is required to suffer strong extinction, which can be reconciled if the line-of-sight skims the outer surface of the torus. Thermal bremsstrahlung radio emission from the warm reflector may be detectable in VLBA radio maps of the NGC 1068 nucleus.

Colbert, Edward J. M.↗

Estimating the Average Diameter of a Population of Spheres from Observed Diameters of Random Two-Dimensional Sections

Size distributions of chondrules, volcanic fire-fountain or impact glass spherules, or of immiscible globules in silicate melts (e.g., in basaltic mesostasis, agglutinitic glass, impact melt sheets) are imperfectly known because the spherical objects are usually so strongly embedded in the bulk samples that they are nearly impossible to separate. Hence, measurements are confined to two-dimensional sections, e.g. polished thin sections that are commonly examined under reflected light optical or backscattered electron microscopy. Three kinds of approaches exist in the geologic literature for estimating the mean real diameter of a population of 3D spheres from 2D observations: (1) a stereological approach with complicated calculations; (2) an empirical approach in which independent 3D size measurements of a population of spheres separated from their parent sample and their 2D cross sectional diameters in thin sections have produced an array of somewhat contested conversion equations; and (3) measuring pairs of 2D diameters of upper and lower surfaces of cross sections each sphere in thin sections using transmitted light microscopy. We describe an entirely probabilistic approach and propose a simple factor of 4/x (approximately equal to 1.27) to convert the 2D mean size to 3D mean size.

Kong, Maiying↗

VIIRS ZEMAX and FORTRAN Polarization Models

The Visible/Infrared Imager/Radiometer Suite (VIIRS) collects visible/infrared imagery and radiometric data. The radiometric requirements are such that the instrument's polarization sensitivity must be very well understood. This paper presents the ZEMAX and FORTRAN polarization ray trace models of the instrument's visible light path. This will include the measured optical surface reflectance data, the bandpass shapes and a comparison of the results of the two models.

Waluschka, Eugene↗

LISA Laser Development in the US

Lowering phase noise: 1) optimize optical cavity reflectivity slope to strong feedback to low noise. 2) optimize gain chip for low loss to low noise. 3) select gain chip for lowest 1/f noise.

External Cavity Laser↗

Simulating response versus scan angle characterization on OCI for the upcoming PACE mission

The Plankton, Aerosol, Cloud ocean Ecosystem (PACE) mission Ocean Color Instrument (OCI) is the next generation ocean color sensor following on from the SeaWiFS and VIIRS designs, to be launched into low Earth orbit in 2022. Like those heritage sensors, OCI has cross track scanning fore-optics, the reflectivity of which (referred to here as the response versus scan angle or RVS) must be characterized prior to launch. The expected test setup, component reflectivity measurements, instrument model, and heritage sensor testing were used to generate simulated RVS data. This simulated data set was then used to verify the functionality of the analysis software in preparation for the upcoming ground test campaign. The analysis software is designed to characterize the RVS for all OCI bands over the full range of scan angles to be measured on orbit as well as verify compliance with the sensor design requirements in near real-time.

PACE↗

Optical enhancing durable anti-reflective coating

Disclosed herein are polysilsesquioxane based anti-reflective coating (ARC) compositions, methods of preparation, and methods of deposition on a substrate. In embodiments, the polysilsesquioxane of this disclosure is prepared in a two-step process of acid catalyzed hydrolysis of organoalkoxysilane followed by addition of tetralkoxysilane that generates silicone polymers with >40 mol % silanol based on Si-NMR. These high silanol siloxane polymers are stable and have a long shelf-life in the polar organic solvents at room temperature. Also disclosed are low refractive index ARC made from these compositions with and without additives such as porogens, templates, Si--OH condensation catalyst and/or nanofillers. Also disclosed are methods and apparatus for applying coatings to flat substrates including substrate pre-treatment processes, coating processes including flow coating and roll coating, and coating curing processes including skin-curing using hot-air knives. Also disclosed are coating compositions and formulations for highly tunable, durable, highly abrasion-resistant functionalized anti-reflective coatings.

36 MATERIALS SCIENCE↗

Methods for the synthesis of arrays of DNA probes

The synthesis of arrays of DNA probes sequences, polypeptides, and the like is carried out using a patterning process on an active surface of a substrate. An image is projected onto the active surface of the substrate utilizing reflective projection optics. The projection optics project a light image onto the active surface of the substrate to deprotect linker molecules thereon. A first level of bases may then be applied to the substrate, followed by development steps, and subsequent exposure of the substrate utilizing a different light image, with further repeats until the elements of a two dimensional array on the substrate surface have an appropriate base bound thereto.

59 BASIC BIOLOGICAL SCIENCES↗

On-PIC Light Source Integration & Micro-dispensing of Solder Paste for Flip Chip Application

To reach the next level benefits of photonic integrated circuits (PICs), the Integrated Photonic Systems Roadmap-International describes the necessity of either heterogeneous or hybrid integration of light sources [1]. A new approach for hybrid integration is Photonic Wire Bonding where 3D nanolithography is used to pattern a polymer waveguide that connects light sources to PIC waveguides. The waveguides resemble electrical wire bonds and essentially do the same as their electrical counterpart for packaging photonic chips together. In order to reap the full benefits of a photonic wire bonds, the light source must be carefully packaged. In this work I seek to expand RIT’s photonic packaging capability by establishing a packaging process to integrate light sources, specifically an Indium Phosphide distributed feedback lasers and a reflective semiconductor optical amplifiers, directly onto a photonic integrated circuits. Another necessary requirement for PIC packaging is densely integrated electrical connectivity. In this thesis I developed a fine pitch flip chip interconnect technique demonstrated using gold stud bumps in conjunction with micro-dispensed solder paste. This work opens the door to high density photonic flip chip applications. The micro-dispensed solder paste dots having diameters 50-125 µm are currently being tested at a pitch of 150 µm . The gold stud bumps are formed with 1mil gold wire creating bumps with a diameter of 40-60 µm depending on specific parameter values. These capabilities will allow RIT to assemble and test novel photonic integrated devices, cutting down on the time and cost associated with third party assembly and tests facilities. Thereby keeping RIT at the forefront of photonic research.

Wongk, Nicole↗