Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Material microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Structural investigation of the temperature-stable relaxor dielectric Ba 0.8 Ca 0.2 TiO 3 -Bi(Mg 0.5 Ti 0.5 )O 3

Aberration corrected scanning transmission electron microscopy (STEM) and electron diffraction have been used to disclose local structure and nano-chemistry in a Ca modified BaTiO 3 -Bi(Mg 0.5 Ti 0.5 )O 3 relax or dielectric ceramic which exhibits high and near-invariant relative permittivity over a wide temperature range. High resolution, synchrotron X-ray diffraction indicated a globally cubic structure ($Pm$$\overline{3}$$m$), but direct atomic-scale imaging by STEM revealed local tetragonal distortions. Nanopolar clusters were identified from B-site atomic displacement vectors measured relative to oxygen ion positions along < 100 > and < 110 > zone axes of integrated differential phase contrast (iDPC) STEM images, highlighting cluster sizes of 2–5 nm. Chemical analysis by STEM-energy dispersive X-ray spectroscopy and full pattern refinements of X-ray powder diffraction data each implied high levels of Bi vacancies within the matrix. The possibility that these A-site vacancies modulate the nanopolar structure and promote flattening of the permittivity-temperature response in this class of dielectric is discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Strongly nonlinear wave propagation in elasto-plastic metamaterials: Low-order dynamic modeling

Nonlinear elastic metamaterials are known to support a variety of dynamic phenomena that enhance our capacity to manipulate elastic waves. Since these properties stem from complex, subwavelength geometry, full-scale dynamic simulations are often prohibitively expensive at scales of interest. Prior studies have therefore utilized low-order effective medium models, such as discrete mass-spring lattices, to capture essential properties in the long-wavelength limit. While models of this type have been successfully implemented for a wide variety of nonlinear elastic systems, they have predominantly considered dynamics depending only on the instantaneous kinematics of the lattice, neglecting history-dependent effects, such as wear and plasticity. Here, to address this limitation, the present study develops a lattice-based modeling framework for nonlinear elastic metamaterials undergoing plastic deformation. Due to the history- and rate-dependent nature of plasticity, the framework generally yields a system of differential-algebraic equations whose computational cost is significantly greater than an elastic system of comparable size. We demonstrate the method using several models inspired by classical lattice dynamics and continuum plasticity theory and explore means to obtain empirical plasticity models for general geometries, thereby gaining insight into the influence of microstructural plasticity on effective material performance, which can be used to improve the design of nonlinear mechanical metamaterials.

Dynamic simulation↗
DOE OSTI2023

A novel design of transitional layer structure between reduced activation ferritic martensitic steels and tungsten for plasma facing materials

Plasma-facing components (PFCs) are among the most critical gaps for fusion energy to establish technical and economic feasibility. Tungsten as a first wall/blanket material in PFCs requires to be integrating with reduced activation ferritic martensitic (RAFM) steels as a structural component. Currently, major drawbacks are the requirement of brazing, the formation of a brittle interface, and a large difference between the coefficients of thermal expansion of tungsten and steel. Here, a novel transitional multilayer structure was designed and investigated to join tungsten and RAFM steels using three interlayers. The composition of each interlayer was selected based on computational thermodynamics and diffusion kinetics to ensure a body-centered cubic (bcc) single-phase structure and prevent the formation of a brittle intermetallic phase region in the temperature range of 600–1150 °C. Although the transitional layer structure was designed for additive manufacturing, spark plasma sintering (SPS) as proof of concept was used to bond the individual layers. Interfaces were investigated using scanning and transmission electron microscopy methods but no layered intermetallic phase was observed. Nanoindentation maps across the interface suggest major hardness differences at the interface between tungsten and the vanadium interlayer, as well as the interface between RAFM steel and the FeCrAl interlayer.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Analysis of position-dependent cavity parameters in irradiated metals to obtain insight on fundamental defect migration phenomena

Motion of point defects is a fundamental process that governs microstructure and properties of materials. Here, we examine the near-surface and grain boundary cavity swelling depth profiles in neutron- and ion-irradiated simple metals (Cu, Ni, and Fe-Cr) and investigate diffusional broadening of implanted Ni ions in Fe-Cr alloys. Vacancy migration energies and radiation-enhanced diffusion were experimentally estimated. Cavity denuded zone widths near planar sinks are shown to be dependent on temperature, damage rate, balance of point defects and sinks, and vacancy migration energies. An enhanced cavity swelling zone adjacent to the void-denuded zone was observed in specimens with low to moderate sink strength and interpreted as evidence of 1D gliding interstitial clusters. Radiation-enhanced diffusional broadening of implanted Ni ions (at 400–550 °C) in Fe and Fe-Cr was up to 250 nm toward the surface, which leads to a much broader near-peak-damage region where cavity swelling is suppressed. Diffusional broadening of implanted ions is calculated to be similarly pronounced for self-ion irradiations, particularly near the peak and higher swelling temperature regimes. Adequately high ion energies (~8–15 MeV) are recommended for ion-irradiation studies to provide a sufficiently broad midrange safe analysis region with minimized surface and injected ion effects.

36 MATERIALS SCIENCE↗
DOE OSTI2023

A new efficient grain growth model using a random Gaussian-sampled mode filter

This paper presents the use of a Gaussian neighborhood mode filter for predicting grain growth in a manner similar to the solutions obtained by a Monte Carlo Potts model. This flexible grain growth model can quickly utilize modern, computationally optimized data science strategies on graphics processing units to simulate grain growth up to 100 times faster than the state-of-the-art, publicly available Monte Carlo Potts model. We show that, given the correct neighborhood, the mode filter can replicate normal grain growth in two or three dimensions. In addition, the paper briefly demonstrates the ability to model limited anisotropic in grain boundary energy and mobility. Anisotropic grain boundary energy is modeled by defining a weighted mode filter operation. Anisotropic grain boundary mobility is modeled by scaling and orienting the Gaussian neighborhood in a particular direction.

Anisotropy↗
DOE OSTI2022

Strain-rate dependent deformation mechanisms in single-layered Cu, Mo, and multilayer Cu/Mo thin films

Here, strain-rate sensitivity and rate-dependent hardness, over a range of 10 -2 to 10 2 s -1 , of sputter-deposited single-layered Cu, Mo, and 5 nm Cu/ 5 nm Mo, and 100 nm Cu/ 100 nm Mo multilayer films with a total film thickness of 5 μm were measured using nanoindentation. The plastic zone underneath the nanoindents was characterized via cross-sectional transmission electron microscopy (XTEM). The multilayer films exhibited enhanced hardness but slightly reduced strain-rate sensitivity with decreasing layer thickness from 100 nm to 5 nm. Only the 5 nm Cu/ 5 nm Mo multilayer film exhibited shear bands underneath the nanoindents, and the size of the shear bands increased with increasing strain rate. In contrast, the 100 nm Cu/ 100 nm Mo multilayer film exhibited material pile-up around the indents and significant nanotwinning within Cu grains. The effect of strain rate and layer thickness on the hardness and strain rate sensitivity of the multilayer thin films is interpreted using a modified confined layer slip (CLS) model. The reduced rate sensitivity at 5 nm as compared to 100 nm correlates with abundant growth nanotwins in the Cu grains in 100 nm and formation of shear bands in 5 nm multilayers. In single layer films, a substructure with a high density of dislocations was observed consistent with the plastic strain gradient in the indent plastic zone. No evidence of deformation twins was noted in any of the samples.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Evolution of microstructure and strength of a high entropy alloy undergoing the strain-induced martensitic transformation

In a recent work, we have reported outstanding strength and work hardening exhibited by a metastable high entropy alloy (HEA), Fe 42 Mn 28 Co 10 Cr 15 Si 5 (in at. %), undergoing the strain-induced martensitic transformation from metastable gamma austenite (γ) to stable epsilon martensite (ε). However, the alloy exhibited poor ductility, which was attributed to the presence of the brittle sigma (σ) phase in its microstructure. The present work reports the evolution of microstructure, strength, and ductility of a similar HEA, Fe 38.5 Mn 20 Co 20 Cr 15 Si 5 Cu 1.5 (in at. %), designed to suppress the formation of σ phase. A cast and then rolled plate of the alloy was processed into four conditions by annealing for 10 and 30 min at 1100 °C and by friction stir processing (FSP) at tool rotation rates of 150 and 400 revolutions per minute (RPM) to facilitate detailed examinations of variable initial grain structures. Neutron diffraction and electron microscopy were employed to characterize the microstructure and texture evolution. The initial materials had variable grain size but nearly 100% γ structure. Diffusionless strain induced γ→ε phase transformation took place under compression with higher rate initially and slower rate at the later stages of deformation, independent on the initial grain size. The transformation facilitated part of plastic strain accommodation and rapid strain hardening owing to a transformation-induced dynamic Hall-Petch-type barrier effect, increase in dislocation density, and texture. Here, the peak strength of nearly 2 GPa was achieved under compression using the structure created by double pass FSP (150 RPM followed by 150 RPM). Remarkably, the tensile elongation exhibited by the alloy was nearly 20% with fracture surfaces featuring a combination of ductile dimples and cleavage.

36 MATERIALS SCIENCE↗
DOE OSTI2026

A fast and robust computational modeling approach for density and shape predictions in powder metallurgy hot isostatic pressing

Powder metallurgy hot isostatic pressing (PM-HIP) is an advanced manufacturing process that produces near-net-shape parts with high material utilization and uniform microstructures. PM-HIP is frequently used for producing small-scale parts with complicated geometries and is potentially economical for producing large-scale parts. However, excessive post-HIP shape distortions can reduce its effectiveness and economic advantage, especially for larger parts. A PM-HIP computational model can predict and help mitigate these distortions. However, due to complex deformation mechanisms and thermo-mechanical coupling present in PM-HIP processes, these non-linear computational models sometimes become numerically unstable. The numerical instabilities in these models can lead to very slow convergence or no convergence at all, which often translates to slow and unreliable models. These limitations are more pronounced in large models with complicated geometries. Hence, in this work, an alternative modeling approach is presented that improves numerical stability and computational performance. The presented approach achieves these improvements through approximating the fully coupled thermo-mechanical PM-HIP model as a decoupled model and adding inertial damping to the model’s mechanical part. In conclusion, a comparison with the fully coupled model indicated a slight dip in prediction accuracy (<5% error) but significant improvements in numerical stability (>20 times larger time step size) and computational performance (5-10 times speed-up with less computational resource usage) when using the presented approach.

Hot isostatic pressing↗
DOE OSTI2020

Effect of oxidation post treatments on TiO 2 coating manufactured using reactive very low-pressure plasma spraying (R-VLPPS)

TiO 2 coatings manufactured using reactive very low-pressure plasma spraying (R-VLPPS) were analyzed in different regions related to their position compared to the plasma flame. For that, a screen was used in order to hide an area of the substrate from the direct plasma flux. The coating morphology changed from quasi lamellar structure to highly vapor structure and coatings exhibited obvious modifications in terms of phases and mechanical properties. The effect of oxidation post treatment on the as sprayed coating was then studied by selecting two methods: in situ oxidation post treatment and classical thermal treatment. The two post treatments provided an increase of the main rutile phase and a decrease of both the size and the contents of porosity simultaneously.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Chapter 15: Summary and Outlook

In the various chapters of this book, numerous characterization techniques are presented that can be applied to thin-film solar cells to determine (micro)structural, compositional, electrical, and optoelectronic properties. What has yet to be more fully elucidated is to what extent these characterization techniques can be combined, in a correlative way, to enhance the information gathered on materials and devices. Indeed, it is valuable to consider combining techniques to verify the relevance of the measured materials properties or to obtain them on different length scales-to compare surface with bulk properties, or to correlate structure and composition of materials with electrical and optoelectronic properties.

41 EE - Solar Energy Technologies Office (EE-4S)↗
DOE OSTI2023

Impact of fabrication methods on binder distribution and charge transport in composite cathodes of all-solid-state batteries

Abstract The manufacturing process of all-solid-state batteries necessitates the use of polymer binders. However, these binders, being ionic insulators by nature, can adversely affect charge transport within composite cathodes, thereby impacting the rate performance of the batteries. In this work, we aim to investigate the impact of fabrication methods, specifically the solvent-free dry process versus the slurry-cast wet process, on binder distribution and charge transport in composite cathodes of solid-state batteries. In the dry process, the binder forms a fibrous network, while the wet process results in binder coverage on the surface of cathode active materials. The difference in microstructure leads to a notable 20-fold increase in ionic conductivity in the dry-processed cathode. Consequently, the cells processed via the dry method exhibit higher capacity retention of 89% and 83% at C/3 and C/2 rates, respectively, in comparison to 68% and 58% for the wet-processed cells at the same rate. These findings provide valuable insights into the influence of fabrication methods on binder distribution and charge transport, contributing to a better understanding of the binder’s role in manufacturing of all-solid-state batteries.

Emley, Benjamin↗
DOE OSTI2022

Understanding the fundamental driver of semiconductor radiation tolerance with experiment and theory

Space is the operating environment of a multitude of systems that our society is heavily reliant on today, however, maintaining operability there necessitates special consideration of the electronic systems' tolerance of space radiation. Electronic systems are critically dependent on the electronic properties of their semiconductor components, which are modified by space radiation with an adverse impact on the space system performance. What innate property allows some semiconductors to sustain little damage while others accumulate defects rapidly with dose is poorly understood, which limits the extent to which radiation tolerance can be implemented as a design criterion. Here, to gain insight into what properties are drivers of semiconductor radiation tolerance, the first step is to generate a dataset of the relative radiation tolerance of a broad sampling of semiconductors. To accomplish this, Rutherford backscatter channeling experiments are used to compare the displaced lattice atom buildup in InAs, InP, GaP, GaN, ZnO, MgO, and Si as a function of stepwise alpha particle dose. With this experimental information on radiation-induced incorporation of interstitial defects in hand, hybrid density functional theory electron densities (and their derived quantities) are calculated and their gradient and Laplacian are evaluated to obtain key fundamental information about the interactions in each material. It is shown that simple, undifferentiated values (which are typically used to describe bond strength) are insufficient to predict radiation tolerance. Instead, the curvature of the electron density at bond critical points provides a measure of radiation tolerance consistent with the experimental results obtained. This curvature and associated forces surrounding bond critical points have the potential to disfavor the localization of displaced lattice atoms at these points, favoring their diffusion toward perfect lattice positions. With this criterion to predict radiation tolerance, simple density functional theory simulations can be conducted on potential new materials to gain insight into how they may operate in demanding high radiation environments.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Niobium hydride formation in superconducting qubit thin films

The formation of nonsuperconducting hydrides in 160–170-nm-thick films of niobium is examined. We identify six elastically distinct orientation relationships ɛ−Nb 4 ⁢H 3 takes within the matrix, solid-solution 𝛼−NbH 𝑥 phase. We employ a phase field model to assess the impact of elastic energy induced by the strain of phase transformation on the morphology and transformation dynamics of ɛ precipitates within a thin film. We consider the dimensions of the thin film, crystallographic growth direction, and diffusion rates to predict the timescale of hydride evolution. Leveraging the finite element method, we predict two-dimensional and three-dimensional equilibrium shapes of ɛ-hydrides within a bulk sample and in a thin film that has a traction-free surface. Our results suggest that niobium hydrides migrate to the free surface of the film. Precipitates which reach the free surface coarsen, while precipitates within the film dissolve. Precipitates in both two dimensions and three dimensions experience a repulsive interaction force at the free surface, that is attractive in the bulk, shown in experiment and theory of previous studies.

36 - MATERIALS SCIENCE↗
DOE OSTI2023

Combining synchrotron X-ray diffraction, mechanistic modeling and machine learning for in situ subsurface temperature quantification during laser melting

Laser melting, such as that encountered during additive manufacturing, produces extreme gradients of temperature in both space and time, which in turn influence microstructural development in the material. Qualification and model validation of the process itself and the resulting material necessitate the ability to characterize these temperature fields. However, well established means to directly probe the material temperature below the surface of an alloy while it is being processed are limited. To address this gap in characterization capabilities, a novel means is presented to extract subsurface temperature-distribution metrics, with uncertainty, from in situ synchrotron X-ray diffraction measurements to provide quantitative temperature evolution data during laser melting. Temperature-distribution metrics are determined using Gaussian process regression supervised machine-learning surrogate models trained with a combination of mechanistic modeling (heat transfer and fluid flow) and X-ray diffraction simulation. The trained surrogate model uncertainties are found to range from 5 to 15% depending on the metric and current temperature. The surrogate models are then applied to experimental data to extract temperature metrics from an Inconel 625 nickel superalloy wall specimen during laser melting. The maximum temperatures of the solid phase in the diffraction volume through melting and cooling are found to reach the solidus temperature as expected, with the mean and minimum temperatures found to be several hundred degrees less. The extracted temperature metrics near melting are determined to be more accurate because of the lower relative levels of mechanical elastic strains. However, uncertainties for temperature metrics during cooling are increased due to the effects of thermomechanical stress.

36 MATERIALS SCIENCE↗
DOE OSTI2022

ExaAM: Metal additive manufacturing simulation at the fidelity of the microstructure

Additive manufacturing (AM), or 3D printing, of metals is transforming the fabrication of components, in part by dramatically expanding the design space, allowing optimization of shape and topology. However, although the physical processes involved in AM are similar to those of welding, a field with decades of experimental, modeling, simulation, and characterization experience, qualification of AM parts remains a challenge. The availability of exascale computational systems, particularly when combined with data-driven approaches such as machine learning, enables topology and shape optimization as well as accelerated qualification by providing process-aware, locally accurate microstructure and mechanical property models. We describe the physics components comprising the Exascale Additive Manufacturing simulation environment and report progress using highly resolved melt pool simulations to inform part-scale finite element thermomechanics simulations, drive microstructure evolution, and determine constitutive mechanical property relationships based on those microstructures using polycrystal plasticity. We report on implementation of these components for exascale computing architectures, as well as the multi-stage simulation workflow that provides a unique high-fidelity model of process–structure–property relationships for AM parts. In addition, we discuss verification and validation through collaboration with efforts such as AM-Bench, a set of benchmark test problems under development by a team led by the National Institute of Standards and Technology.

3D printing↗
DOE OSTI2022

Simulating microgalvanic corrosion in alloys using the PRISMS phase-field framework

In this prospective paper, we first review the existing simulation tools to simulate microgalvanic corrosion during free immersion. Then, we describe a recently developed application that employs PRISMS-PF, an open-source, high-performance phase-field modeling framework. The model employed in the application accounts for the electrochemical reaction at the metal/electrolyte interface and ionic migration in the electrolyte to determine the evolution of the corrosion front. We present the implementation details for the application and discuss its features such as super-linear parallel scaling performance for a sufficiently large system. Finally, we demonstrate the capability of the application by simulating corrosion of the matrix phase of an alloy near a secondary phase particle in two and three dimensions.

36 MATERIALS SCIENCE↗