Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MAGNETRONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42

Metal-ion-controlled growth and nanoindentation response of 3D, bicontinuous Cu–Fe thin films

Bicontinuous, nanocomposite thin film morphologies depend largely on the deposition conditions applied during physical vapor deposition. With the introduction of high power impulse magnetron sputtering (HiPIMS), the range of potential morphologies achieved during deposition has been increased. In this work, we compare the deposition outcomes between traditional direct-current magnetron sputtering (DCMS) and HiPIMS for a thin film co deposit of Cu and Fe. Modular control of the columnarity, porosity and roughness was achieved by varying the Cu and Fe metal ion currents during deposition. The directionality of the nanostructured phase-separated morphology was also controlled as the ion current increased. At zero ion current for both Cu and Fe sputtered species during DCMS, the film exhibited lateral concentration modulations of Cu and Fe. The directionality of the Cu- and Fe-rich phases shifted to vertical concentration modulations at low ion currents of I Fe = 1A and I Cu = 0:1A and to lateral concentration modulations at relatively moderate ion currents of I Fe = 5A and I Cu = 2A: At high ion currents of I Fe = 18A and I Cu = 2A; a more randomized phase domain structure was observed on the nanoscale. This structural shift is rationalized using an interdiffusion model. Here, the role of different kinds of phase separated morphologies, achieved during DCMS deposition, on the mechanical properties has also been studied. Results indicated increase in hardness, indentation modulus and flow strength values with the increase in indentation strain rates. Bicontinuous Cu-Fe nanocomposites are found to be stronger than multilayer Cu-Fe samples.

36 MATERIALS SCIENCE↗

CdS/CdTe Solar Cells Containing Directly-Deposited CdSxTe1-x Alloy Layers

A CdS{sub x}Te{sub 1-x} layer forms by interdiffusion of CdS and CdTe during the fabrication of thin-film CdTe photovoltaic (PV) devices. The CdS{sub x}Te{sub 1-x} layer is thought to be important because it relieves strain at the CdS/CdTe interface that would otherwise exist due to the 10% lattice mismatch between these two materials. Our previous work [1] has indicated that the electrical junction is located in this interdiffused CdS{sub x}Te{sub 1-x} region. Further understanding, however, is essential to predict the role of this CdS{sub x}Te{sub 1-x} layer in the operation of CdS/CdTe devices. In this study, CdS{sub x}Te{sub 1-x} alloy films were deposited by radio-frequency (RF) magnetron sputtering and co-evaporation from CdTe and CdS sources. Both RF-magnetron-sputtered and co-evaporated CdS{sub x}Te{sub 1-x} films of lower S content (x<;0.3) have a cubic zincblende (ZB) structure akin to CdTe, whereas those of higher S content have a hexagonal wurtzite (WZ) structure like that of CdS. Films become less preferentially oriented as a result of a CdCl{sub 2} heat treatment (HT) at {approx}400 C for 5 min. Films sputtered in a 1% O{sub 2}/Ar ambient are amorphous as deposited, but show CdTe ZB, CdS WZ, and CdTe oxide phases after a CdCl{sub 2} HT. Films sputtered in O{sub 2} partial pressure have a much wider bandgap than expected. This may be explained by nanocrystalline size effects seen previously [2] for sputtered oxygenated CdS (CdS:O) films. Initial PV device results show that the introduction of a directly-deposited CdS{sub x}Te{sub 1-x} alloy layer into the device structure produces devices of comparable performance to those without the alloy layer when a CdCl{sub 2} HT is performed. Further investigation is required to determine whether the CdCl{sub 2} heat treatment step can be altered or eliminated through direct deposition of the alloy layer.

14 SOLAR ENERGY↗

Development of a cosputter-evaporation chamber for Fe-Ga films

A new deposition technique involving the dc magnetron sputtering of Fe simultaneously with Ga evaporation has been developed to fabricate thin Fe{sub (1-x)}Ga{sub x} (0<x<0.4) films. Simultaneous sputtering and evaporation has been developed as an alternative to the sputtering of alloy targets, where the need for compositional variation can be hard to address. The new technique allows the freedom of composition that cosputtering would offer, but mitigates the issue of being unable to sputter Ga. The need for the preparation of alloy targets is also avoided. To control the concentration of the Ga in the films, the evaporation rate, the dc magnetron power, and the chamber pressure were varied. The films fabricated were studied to determine their magnetic and microstructural properties. The Fe-Ga films fabricated had magnetostriction constants which had increased by a factor of 5 compared to the same thickness of Fe film.

36 MATERIALS SCIENCE↗

Modeling for calculation of vanadium oxide film composition in reactive-sputtering process

A modified model describing the changing ratio of vanadium to oxide on the target and substrate as a function of oxygen flow is described. Actually, this ratio is extremely sensitive to the deposition conditions during the vanadium oxide (VO{sub x}) reactive magnetron-sputtering process. The method in this article is an extension of a previously presented Berg's model, where only a single stoichiometry compound layer was taken into consideration. This work deals with reactive magnetron sputtering of vanadium oxide films with different oxygen contents from vanadium metal target. The presence of vanadium mixed oxides at both target and substrate surface produced during reactive-sputtering process are included. It shows that the model can be used for the optimization of film composition with respect to oxygen flow in a stable hysteresis-free reactive-sputtering process. A systematic experimental study of deposition rate of VO{sub x} with respect to target ion current was also made. Compared to experimental results, it was verified that the theoretical calculation from modeling is in good agreement with the experimental counterpart.

36 MATERIALS SCIENCE↗

Microstructure and tribological performance of nanocomposite Ti-Si-C-N coatings deposited using hexamethyldisilazane precursor

Thick nanocomposite Ti-Si-C-N coatings (20-30 {mu}m) were deposited on Ti-6Al-4V substrate by magnetron sputtering of Ti in a gas mixture of Ar, N{sub 2}, and hexamethyldisilazane (HMDSN) under various deposition conditions. Microstructure and composition of the coatings were studied using scanning electron microscopy, x-ray diffraction, and energy dispersive x-ray spectroscopy, while the mechanical and tribological properties of these coatings were studied using Rc indentation, and micro- and nanoindentations, solid particle erosion testing, and ball-on-disk wear testing. It has been observed that the Si concentration of these coatings is varied from 0% (TiN) to 15% (Ti-Si-C-N), while the structure of these coatings is similar to the nanocomposite Ti-Si-N coatings and consists of nanocrystalline B1 structured Ti(C,N) in an amorphous matrix of SiC{sub x}N{sub y} with the grain size of 5->100 nm, depending on the coating preparation process. These coatings exhibit excellent adhesion when subjected to Rc indentation tests. The microhardness of these coatings varies from 1200 to 3400 HV25, while the nanohardness varies from 10 to 26 GPa. Both the microhardness and nanohardness are slightly lower than those of similar coatings prepared using trimethylsilane. However, the erosion test using a microsand erosion tester at both 30 deg. and 90 deg. incident angles shows that these coatings have very high erosion resistance and up to a few hundred times of improvement has been observed. These coatings also exhibit very high resistance to sliding wear with a low coefficient of friction of about 0.2 in dry sliding. There are a few advantages of using the HMDSN precursor to prepare the Ti-Si-C-N coatings over conventional magnetron sputtered deposition of Ti-Si-N coatings including composition uniformity, precursor handling safety, and high deposition rate. The coatings can be applied to protect gas turbine compressor blades from solid particle erosion and steam turbine blades from liquid droplet erosion, as well as other mechanical components that experience severe abrasion. These coatings may also be used in areas where both high wear resistance and low friction are required.

36 MATERIALS SCIENCE↗

Effects of temperature and near-substrate plasma density on the structural and electrical properties of dc sputtered germanium thin films

Germanium thin films were deposited by dc reactive magnetron sputtering as a function of substrate temperature and ion flux using an unbalanced magnetron with an external magnetic field. The ion flux and energy distribution were measured using a retarding field energy analyzer (RFEA), a flat probe with a guard ring, and cylindrical Langmuir probes. The RFEA ion flux, the flat probe saturation currents, and the ion densities inferred from the cylindrical probe data are in very good agreement over a wide range of plasma densities, which were varied both by the external coil current and discharge power. The RFEA ion energy distributions are in good agreement with the plasma potentials inferred from the cylindrical probes, and suggest that the nonuniformity of the plasma in the vicinity of the substrate holder should be considered in the interpretation of probe results in these systems. The deposited films were characterized by x-ray diffraction, Raman spectroscopy, optical transmission, resistivity, and Hall effect measurements. Under low ion bombardment conditions, an abrupt onset of the crystalline phase with respect to temperature is observed in the Raman and x-ray diffraction measurements, and the crystal quality increases with increasing temperature above the transition temperature. The transition is also accompanied by a sharp decrease in film resistivity. The microcrystalline films have a strong preferential orientation in the (220) direction, and are p type with carrier densities in the range 10{sup 18} cm{sup -3} and mobilities in the range 15-30 cm{sup 2}/V-s. The structural and electronic properties of the films are sensitive to the ion flux. Near the transition temperature the effects of increasing ion flux can be attributed to the small temperature rise that accompanies the higher plasma density. At higher temperatures the increased ion flux results in a more random crystallographic orientation, with significantly lower carrier concentrations and only slightly lower carrier mobilities, implying either a reduction in acceptor defect density and/or the creation of compensating n-type defects.

36 MATERIALS SCIENCE↗

Interdiffusion in nanometric Fe/Ni multilayer films

[Fe (3.1 nm)/Ni (3.3 nm)]{sub 20} multilayer films were prepared by DC magnetron sputtering onto oxidized Si(100) substrates. The Fe and Ni layers were shown to both be face-centered cubic by x-ray diffraction. Interdiffusion of the Fe and Ni layers in the temperature range of 300–430 °C was studied by x-ray reflectivity. From the decay of the integral intensity of the superlattice peak, the activation energy and the pre-exponential term for the effective interdiffusion coefficient were determined as to 1.06 ± 0.07 eV and 5 × 10{sup −10} cm{sup 2}/s, respectively. The relevance of the measured interdiffusion coefficient to the laboratory timescale synthesis of L1{sub 0} ordered FeNi as a rare-earth free permanent magnet is discussed.

36 MATERIALS SCIENCE↗

Zero added oxygen for high quality sputtered ITO: A data science investigation of reduced Sn-content and added Zr

The authors demonstrate mobilities of >45 cm{sup 2}/V s for sputtered tin-doped indium oxide (ITO) films at zero added oxygen. All films were deposited with 5 wt. % SnO{sub 2}, instead of the more conventional 8–10 wt. %, and had varying ZrO{sub 2} content from 0 to 3 wt. %, with a subsequent reduction in In{sub 2}O{sub 3} content. These films were deposited by radio-frequency magnetron sputtering from nominally stoichiometric targets with varying oxygen partial pressure in the sputter ambient. Anomalous behavior was discovered for films with no Zr-added, where a bimodality of high and low mobilities was discovered for nominally similar growth conditions. However, all films showed the lowest resistivity and highest mobilities when the oxygen partial pressure in the sputter ambient was zero. This result is contrasted with several other reports of ITO transport performance having a maximum for small but nonzero oxygen partial pressure. This result is attributed to the reduced concentration of SnO{sub 2}. The addition of ZrO{sub 2} yielded the highest mobilities at >55 cm{sup 2}/V s and the films showed a modest increase in optical transmission with increasing Zr-content.

36 MATERIALS SCIENCE↗

Real structure of the ZnO epitaxial films on (0001) leucosapphire substrates coated by ultrathin gold layers

The real structure of ZnO films formed by magnetron sputtering on (0001) leucosapphire substrates coated by an ultrathin (less than 0.7 nm) Au buffer layer has been studied by high-resolution microscopy. It is shown that modification of the leucosapphire substrate surface by depositing ultrathin Au layers does not lead to the formation of Au clusters at the film–substrate interface but significantly improves the structural quality of ZnO epitaxial films. It is demonstrated that the simplicity and scalability of the technique used to modify the substrate surface in combination with a high (above 2 nm/s) film growth rate under magnetron sputtering make it possible to obtain high-quality (0001) ZnO epitaxial films with an area of 5–6 cm{sup 2}.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Structure of Diamond-Like Silicon–Carbon Films Alloyed by Vanadium

The structure of diamond-like silicon–carbon films formed on silicon substrates by magnetron and plasmatron codeposition using a closed-field magnetron and a plasmatron activated by tungsten cathode has been studied by transmission electron microscopy. The main feature of the films alloyed by vanadium to concentrations of 12–31 at % was found to be a layered structure of the film cross section. It was established that vanadium alloying leads to the formation of vanadium carbide (VC) nanocrystals; the nanocrystal size increases from 1–2 to 10 nm. At the maximum vanadium content, VC nanocrystals have an anisotropic shape: they are extended in the direction perpendicular to the film–substrate interface.

36 MATERIALS SCIENCE↗

Redistribution of components in the niobium-silicon system under high-temperature proton irradiation

The redistribution of components in the niobium-silicon system during magnetron-assisted sputtering of niobium, vacuum annealing, and high-temperature proton irradiation is studied. It is established that, during magnetron-assisted sputtering followed by vacuum annealing, silicon penetrates through the metal film to the outer boundary of the film. Under high-temperature proton irradiation, the suppression of the diffusion of niobium into silicon is observed. This effect is attributed to the high concentration of radiation vacancies in the region of the Nb/Si interphase boundary.

36 MATERIALS SCIENCE↗

Study of the interaction mechanisms between absorbed NO{sub 2} and por-Si/SnO{sub x} nanocomposite layers

The interaction mechanisms between NO{sub 2} molecules and the surface of por-Si/SnO{sub x} nanocomposites obtained by magnetron deposition and chemical vapor deposition (CVD) are studied by infrared absorption spectroscopy and electron paramagnetic resonance methods. The observed increase in the free carrier concentration in the por-Si/SnO{sub x} nanocomposite layers is explained by a change in the charge state of P{sub b} centers due to the formation of neutral 'surface defect-adsorbed NO{sub 2} molecule' complexes with free carrier generation in the crystallite bulk. In the nanocomposite layers grown by the CVD method, the increase in the free hole concentration during NO{sub 2} adsorption is much less pronounced in comparison with the composite grown by magnetron deposition, which is caused by the competing interaction channel of NO{sub 2} molecules with electrically neutral P{sub b} centers.

36 MATERIALS SCIENCE↗

Electrical Conductivity and Barrier Properties of Lithium Niobate Thin Films

The thin-film structures made of LiNbO{sub 3} and obtained via laser ablation and magnetron sputtering are studied with volt-farad and volt-ampere characteristics. A potential barrier on the Si–LiNbO{sub 3} interface was found for both types of the films with the capacitance-voltage characteristics. The current-voltage characteristics showed that there are several conduction mechanisms in the structures studied. The Poole–Frenkel effect and the currents limited by a space charge mainly contribute to the electrical conductivity in the LiNbO{sub 3} film produced with the laser ablation method. The currents limited by a space charge contribute to the main mechanism in the film heterostructure obtained with the magnetron sputtering method.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Structural and Magnetic Characteristics of Nanogranular Co–Al{sub 2}O{sub 3} Single- and Multilayer Films Formed by the Solid-State Synthesis

The results of structural and magnetic investigations of nanogranular Co–Al{sub 2}O{sub 3} films formed from Co{sub 3}O{sub 4}/Al thin-film layered structures upon vacuum annealing are reported. The Co{sub 3}O{sub 4}/Al films have been obtained by sequential reactive magnetron sputtering of a metallic cobalt target in a medium consisting of the Ar + O{sub 2} gas mixture and magnetron sputtering of an aluminum target in the pure argon atmosphere. It is shown that such a technique makes it possible to obtain nanogranular Co–Al{sub 2}O{sub 3} single- and multilayer thin films with a well-controlled size of magnetic grains and their distribution over the film thickness.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Effect of Material of Metal Sublayer and Deposition Configuration on the Texture Formation in the Piezoactive ZnO Films

Effect of material of metal sublayer (aluminum, vanadium, chromium, iron, cobalt, nickel, and copper) and deposition configuration on the formation of the oblique and straight texture in the ZnO films is studied. The films that are synthesized in a dc magnetron sputtering system. It is shown that the piezoactive ZnO films with oblique texture that can generate shear waves are formed on the Cr and V metal sublayers in the shifted deposition configuration when the substrate is shifted relative to the magnetron axis toward the region of the target erosion. The piezoactive ZnO films with the straight structure that can generate longitudinal waves are formed on a chemically pure Al sublayer in the symmetric deposition configuration when the substrate is centered with respect to the target. Changes of the sublayer material in both deposition configurations or preliminary oxidation of the sublayer lead to the formation of the piezoactive ZnO films with mixed texture that excite shear and longitudinal waves. Chemical etching is used to show that the ZnO films with the oblique and straight textures exhibit piezoactive properties and can generate hypersound at thicknesses of no less than about 0.3 and about 0.9 μm, respectively.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Computation Modeling and Assessment of Nanocoatings for Ultra Supercritical Boilers (Final Report)

Forced outages and boiler unavailability of coal-fired fossil plants is most often caused by fire-side corrosion of boiler waterwalls and tubing. Reliable coatings are required for Ultrasupercritical (USC) application to mitigate corrosion since these boilers will operate at a much higher temperatures and pressures than in supercritical (565° C @ 24 MPa) boilers. Computational modeling efforts have been undertaken to design and assess potential Fe-Cr-Ni-Al systems to produce stable nanocrystalline coatings that form a protective, continuous scale of either Al 2 O 3 or Cr 2 O 3 . The computational modeling results identified a new series of Fe-25Cr-40Ni with or without 10 wt.% Al nanocrystalline coatings that maintain long-term stability by forming a diffusion barrier layer at the coating/substrate interface. The computational modeling predictions of microstructure, formation of continuous Al 2 O 3 scale, inward Al diffusion, grain growth, and sintering behavior were validated with experimental results. Advanced coatings, such as MCrAl (where M is Fe, Ni, or Co) nanocrystalline coatings, have been processed using different magnetron sputtering deposition techniques. Several coating trials were performed and among the processing methods evaluated, the DC pulsed magnetron sputtering technique produced the best quality coating with a minimum number of shallow defects and the results of multiple deposition trials showed that the process is repeatable. The cyclic oxidation test results revealed that the nanocrystalline coatings offer better oxidation resistance, in terms of weight loss, localized oxidation, and formation of mixed oxides in the Al 2 O 3 scale, than widely used MCrAlY coatings. However, the ultra-fine grain structure in these coatings, consistent with the computational model predictions, resulted in accelerated Al diffusion from the coating into the substrate. An effective diffusion barrier interlayer coating was developed to prevent inward Al diffusion. The fire-side corrosion test results showed that the nanocrystalline coatings with a minimum number of defects have a great potential in providing corrosion protection. The coating tested in the most aggressive environment showed no evidence of coating spallation and/or corrosion attack after 1050 hours exposure. In contrast, evidence of coating spallation in isolated areas and corrosion attack of the base metal in the spalled areas were observed after 500 hours. These contrasting results after 500 and 1050 hours exposure suggest that the premature coating spallation in isolated areas may be related to the variation of defects in the coating between the samples. It is suspected that the cauliflower-type defects in the coating were presumably responsible for coating spallation in isolated areas. Thus, a defect free good quality coating is the key for the long-term durability of nanocrystalline coatings in corrosive environments. Thus, additional process optimization work is required to produce defect-free coatings prior to development of a coating application method for production parts.

01 COAL, LIGNITE, AND PEAT↗

CdS/CdTe Solar Cells Containing Directly Deposited CdSxTe1-x Alloy Layers: Preprint

A CdSxTe1-x layer forms by interdiffusion of CdS and CdTe during the fabrication of thin-film CdTe photovoltaic (PV) devices. The CdSxTe1-x layer is thought to be important because it relieves strain at the CdS/CdTe interface that would otherwise exist due to the 10% lattice mismatch between these two materials. Our previous work [1] has indicated that the electrical junction is located in thisinterdiffused CdSxTe1-x region. Further understanding, however, is essential to predict the role of this CdSxTe1-x layer in the operation of CdS/CdTe devices. In this study, CdSxTe1-x alloy films were deposited by radio-frequency (RF) magnetron sputtering and co-evaporation from CdTe and CdS sources. Both RF-magnetron-sputtered and co-evaporated CdSxTe1-x films of lower S content (x<0.3) have acubic zincblende (ZB) structure akin to CdTe, whereas those of higher S content have a hexagonal wurtzite (WZ) structure like that of CdS. Films become less preferentially oriented as a result of a CdCl2 heat treatment (HT) at~400 degrees C for 5 min. Films sputtered in a 1% O2/Ar ambient are amorphous as deposited, but show CdTe ZB, CdS WZ, and CdTe oxide phases after a CdCl2 HT. Filmssputtered in O2 partial pressure have a much wider bandgap than expected. This may be explained by nanocrystalline size effects seen previously [2] for sputtered oxygenated CdS (CdS:O) films. Initial PV device results show that the introduction of a directly-deposited CdSxTe1-x alloy layer into the device structure produces devices of comparable performance to those without the alloy layer whena CdCl2 HT is performed. Further investigation is required to determine whether the CdCl2 heat treatment step can be altered or eliminated through direct deposition of the alloy layer.

14 SOLAR ENERGY↗