Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “LOW SPEED STABILITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42
All sourcesNASA NTRSDOE OSTI
NASA NTRS1961

Lateral Stability and Control Characteristics of a Four-Propeller Deflected-Slipstream VTOL Model Including the Effects of Ground Proximity

The investigation of the lateral-directional stability and control characteristics of a four-propeller deflected-slipstream VTOL model in the transition speed range was conducted in the 17-foot test section of the Langley 300-MPH 7- by 10-foot tunnel. A large fairing on top of the rear fuselage was needed to eliminate directional instability in the power-off flaps-retracted condition. Even with this fairing some instability at small sideslip angles remained for power-on conditions with low flap deflections. The configuration exhibited a high level of dihedral effect which, coupled with the directional instability, will probably produce an undesirable Dutch roll oscillation.

Kuhn, Richard E.↗
NASA NTRS1949

Preliminary Results of a Free-Flight Investigation of the Static Stability and Aileron Control Characteristics of 1/6 Scale Models of the Bell MX-776

An investigation of the static longitudinal stability, static directional stability, and aileron control characteristics at transonic and supersonic speeds is being made of 1/6 scale rocket-propelled model of the Bell MX-776. A stability investigation has been made of two symmetrical models with controls undeflected and centers of gravity one-half and one-body diameter, respectively, ahead of the equivalent design center-of-gravity location of the full-scale version. Both models developed large normal-force coefficients in both the subsonic and supersonic ranges which indicated longitudinal instability at low angles of attack. The side-force coefficients were small for both models and indicated that the models were directionally stable. A possible tendency toward dynamic directional instability in the transonic region was indicated by short-period oscillations of the side forces. The results showed a partial-span inboard aileron to be ineffective or to cause negative control in the the transonic region when deflected approximately 5 deg but not when deflected 10 deg. An investigation of drag showed it to increase with a rearward movement of the center of gravity. This indicates an increase in the trim angle of attack as could be caused by a decrease in static stability.

Michal, David H.↗
NASA NTRS1947

Wind-Tunnel Tests of the 1/25-Scale Powered Model of the Martin JRM-1 Airplane. IV - Tests with Ground Board and with Modified Wing and Hull - TED No. NACA 232: Tests with Ground Board and with Modified Wing and Hull, TED No. NACA 232 - Part 4

Wind-tunnel tests were made of a 1/25 scale model of the Martin JRM-1 airplane to determine: (1) The longitudinal stability and control characteristics of the JRM-1 model near the water and lateral and directional stability characteristics with power while moving on the surface of the water, the latter being useful for the design of tip floats; (2) The stability and stalling characteristics of the wing with a modified airfoil contour; (3) Stability characteristics of a hull of larger design gross weight; The test results indicated that the elevator was powerful enough to trim the original model in a landing configuration at any lift coefficient within the specified range of centers of gravity. The ground-board tests for evaluating the aerodynamic forces and moments on an airplane in a simulated cross wind indicate a high dihedral effect in the presence of the ground board and, consequently, during low-speed taxying and take-off, large overturning moments would result which would have to be overcome by the tip floats.

Lockwood, Vernard E.↗
NASA NTRS1948

Effect of a Nacelle on the Low-speed Aerodynamic Characteristics of a Swept-back Wing

Wind-tunnel tests of a simplified nacelle on a semispan wing having approximately 35 degrees of sweepback were made at low speeds to evaluate the effects of the nacelle on the aerodynamic characteristics of the wing. Force, moment, and pressure-distribution measurements are presented for the nacelle underslung and centrally mounted on the wing and mounted on a strut below the wing.

WING-NACELLE COMBINATIONS - AIRPLANES↗
NASA NTRS1984

Hover test of a full-scale hingeless rotor

The performance and aeroelastic stability in hover of a 9.8-m diameter, hingeless helicopter rotor system was evaluated. Rotor performance and inplane damping data were obtained for rotor operation between 350 and 425 rpm for thrust coefficients (CT/sigma) between 0.0 and 0.12. At constant rotor thrust, a minimum in rotor inplane damping was measured at 400 rpm. Good agreement is shown between experimental performance data and predicted performance. The influence of different aerodynamic inflow models on predicting damping levels is also shown. The best correlation with experimental stability data was obtained when a dynamic inflow model was used instead of static or quasistatic inflow models. Comparison with other full scale, hingeless rotor data in hover is presented. The hingeless rotor data and data from a full scale, bearingless main rotor test performed on the same general purpose test apparatus were compared. Although the bearingless rotor was more highly damped at design tip speed and 1-g thrust operation, greater sensitivity to operating conditions is shown. At low thrust levels the bearingless main rotor is less damped than the hingeless rotor.

Warmbrodt, W.↗
NASA NTRS1984

Hover test of a full-scale hingeless rotor

The performance and aeroelastic stability in hover of a 9.8-m diameter, hingeless helicopter rotor system was evaluated. Rotor performance and inplane damping data were obtained for rotor operation beteen 350 and 425 rpm for thrust coefficients (CT/sigma) between 0.0 and 0.12. At constant rotor thrust, a minimum in rotor inplane damping was measured at 400 rpm. Good agreement is shown between experimental performance data and predicted performance. The influence of different aerodynamic inflow models on predicting damping levels is also shown. The best correlation with experimental stability data was obtained when a dynamic inflow model was used instead of static or quasistatic inflow models. Comparison with other full scale, hingeless rotor data in hover is presented. The hingeless rotor data and data from a full scale, bearingless main rotor test performed on the same general purpose test apparatus were compared. Although the bearingless rotor was more highly damped at design tip speed and 1-g thrust operation, greater sensitivity to operating conditions is shown. At low thrust levels the bearingless main rotor is less damped than the hingeless rotor.

Warmbrodt, W.↗
DOE OSTI2022

Observational study of the South American low-level jet during the SALLJEX

The South American Low-Level Jet (SALLJ) east of the Andes is a narrow maximum northerly wind present just above the boundary layer. It is an important component of the tropical-extratropical exchange of heat and moisture in South America and favors deep moist convection in Southeastern South America (SESA). In the present study, the SALLJ characteristics during the 2002-2003 summer season are investigated using upper-air measurements collected during the SALLJ Experiment (SALLJEX). At most stations, the highest wind speed was observed below 3000 m between 06 and 12 UTC, mainly in association with a maximization of the northerly component of the wind while the zonal component reached its minimum. Here, an increase in the maximum wind speed from 10°S to Santa Cruz de la Sierra’s latitude and from there a weakening southward was found throughout the SALLJEX network. Additionally, SALLJEX observations allowed to locate SALLJ core purely from observations in a region just east of the Andes in agreement with previous studies. A new localized kinematic classification was developed and applied in this study to analyze the relationship between the SALLJ intensity and the thermodynamic properties of the lower layers of the atmosphere. Weak, moderate, and strong SALLJ categories were defined with a local threshold of the northerly wind speed maximum at each station. The strongest SALLJs were frequently observed at nighttime, while weaker SALLJs were likely to occur at any time of the day. A stabilization of the nocturnal boundary layer was observed between weak and moderate cases whereas a destabilization between moderate and strong cases were found near the time of the wind speed maximum (06 UTC) at Santiago del Estero and Resistencia stations. A deepening of the convective boundary layer and an increase of its mean temperature between weak and strong category during the previous afternoon to nocturnal SALLJs, reveal a possible contribution to the mechanisms that generate the maximum wind speed.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1955

Longitudinal Stability and Control Characteristics as Determined by the Rocket-model Technique for an Inline, Cruciform, Canard Missile Configuration with a Low-aspect-ratio Wing Having Trailing-edge Flap Controls for a Mach Number Range of 0.7 to 1.

Two full-scale models of an inline, cruciform, canard missile configuration having a low-aspect-ratio wing equipped with flap-type controls were flight tested in order to determine the missile's longitudinal aerodynamic characteristics. Stability derivatives and control and drag characteristics are presented for a range of Mach number from 0.7 to 1.8. Nonlinear lift and moment curves were noted for the angle - of-attack range of this test (0 deg to 8 deg). The aerodynamic-center location for angles of attack near 50 remained nearly constant for supersonic speeds at 13.5 percent of the mean aerodynamic chord; whereas for angles of attack near 0 deg, there was a rapid forward movement of the aerodynamic center as the Mach number increased. At a control deflection of 0 deg, the missile's response to the longitudinal control was in an essentially fixed space plane which was not coincident with the pitch plane as a result of the missile rolling. As a consequence, stability characteristics were determined from the resultant of pitch and yaw motions. The damping-in-pitch derivatives for the two angle -of-attack ranges of the test are in close agreement and varied only slightly with Mach number. The horn-balanced trailing-edge flap was effective in producing angle of attack over the Mach number range.

Baber, Hal T , Jr↗
NASA NTRS1955

Longitudinal Stability and Control Characteristics as Determined by the Rocket-Model Technique for an Inline, Cruciform, Canard Missile Configuration with a Low-Aspect-Ratio Wing Having Trailing-Edge Flap Controls for a Mach Number Range of 0.7 to 1.8

Two full-scale models of an inline, cruciform, canard missile configuration having a low-aspect-ratio wing equipped with flap-type controls were flight tested in order to determine the missile's longitudinal aerodynamic characteristics. Stability derivatives and control and drag characteristics are presented for a range of Mach number from 0.7 to 1.8. Nonlinear lift and moment curves were noted for the angle-of-attack range of this test (0 deg to 8 deg ). The aerodynamic-center location for angles of attack near 5 deg remained nearly constant for supersonic speeds at 13.5 percent of the mean aerodynamic chord; whereas for angles of attack near O deg, there was a rapid forward movement of the aerodynamic center as the Mach number increased. At a control deflection of O deg, the missile's response to the longitudinal control was in an essentially fixed space plane which was not coincident with the pitch plane as a result of the missile rolling. As a consequence, stability characteristics were determined from the resultant of pitch and yaw motions. The damping-in-pitch derivatives for the two angle-of-attack ranges of the test are in close agreement and varied only slightly with Mach number. The horn-balanced trailing-edge flap was effective in producing angle of attack over the Mach number range.

Baber, H. T., Jr.↗
NASA NTRS1979

The size and performance effects of high lift system technology on a modern twin engine jet transport

The energy and economic benefits of low-speed aerodynamic system technology applied to a modern 200-passenger, 2000-nmi range, twin engine jet transport are reviewed. Results of a new method to design flap systems at flight Reynolds number are summarized. The study contains the airplane high lift configuration drag characteristics and design selection charts showing the effect of flap technology on the airplane size and performance. The study areas include: wing and flap geometry, climb and descent speed schedules with partial flap deflection, flap system technology, and augmented stability. The results compare the improvements in payload from a hot, high elevation airport.

Sullivan, R. L.↗
NASA NTRS1986

Parametric effects of CFL number and artificial smoothing on numerical solutions using implicit approximate factorization algorithm

An implicit approximate factorization algorithm is employed to quantify the parametric effects of Courant number and artificial smoothing on numerical solutions of the unsteady 3-D Euler equations for a windmilling propeller (low speed) flow field. The results show that propeller global or performance chracteristics vary strongly with Courant number and artificial dissipation parameters, though the variation is such less severe at high Courant numbers. Candidate sets of Courant number and dissipation parameters could result in parameter-dependent solutions. Parameter-independent numerical solutions can be obtained if low values of the dissipation parameter-time step ratio are used in the computations. Furthermore, it is realized that too much artificial damping can degrade numerical stability. Finally, it is demonstrated that highly resolved meshes may, in some cases, delay convergence, thereby suggesting some optimum cell size for a given flow solution. It is suspected that improper boundary treatment may account for the cell size constraint.

Daso, E. O.↗
NASA NTRS1987

Nonlinear lift control at high speed and high angle of attack using vortex flow technology

Nonlinear lift control at subsonic, transonic and low supersonic speeds owes its origin to the separated but organized vortical flows interacting with the wing upper surface. Since most of this flow originates near the wing or control-surface leading edge, a variety of devices has been studied experimentally which interact with and/or control this flow in order to gain a beneficial effect. The benefits (effects) originally studied were associated only with lift enhancement. Whereas, now the studied benefits encompass performance increase, attention to changes in trimmed conditions and longitudinal stability, improvements in lateral stability, and the attendant variation with changing Mach number. For those devices that can be theoretically modeled, state-of-the-art computer codes have been used for device design and/or analysis. Comparisons at design and off-design conditions are presented for validation purposes.

Lamar, John E.↗
NASA NTRS1989

Dynamics of face and annular seals with two-phase flow

A detailed study was made of face and annular seals under conditions where boiling, i.e., phase change of the leaking fluid, occurs within the seal. Many seals operate in this mode because of flashing due to pressure drop and/or heat input from frictional heating. High pressure, water pumps, industrial chemical pumps, and cryogenic pumps are mentioned as a few of many applications. The initial motivation was the LOX-GOX seals for the space shuttle main engine, but the study was expanded to include any face or annular seal where boiling occurs. Some of the distinctive behavior characteristics of two-phase seals were discussed, particularly their axial stability. While two-phase seals probably exhibit instability to disturbances of other degrees of freedom such as wobble, etc., under certain conditions, such analyses are too complex to be treated at present. Since an all liquid seal (with parallel faces) has a neutral axial stiffness curve, and is stabilized axially by convergent coning, other degrees of freedom stability analyses are necessary. However, the axial stability behavior of the two-phase seal is always a consideration no matter how well the seal is aligned and regardless of the speed. Hence, axial stability is thought of as the primary design consideration for two-phase seals and indeed the stability behavior under sub-cooling variations probably overshadows other concerns. The main thrust was the dynamic analysis of axial motion of two-phase face seals, principally the determination of axial stiffness, and the steady behavior of two-phase annular seals. The main conclusions are that seals with two-phase flow may be unstable if improperly balanced. Detailed theoretical analyses of low (laminar) and high (turbulent) leakage seals are presented along with computer codes, parametric studies, and in particular a simplified PC based code that allows for rapid performance prediction. A simplified combined computer code for the performance prediction over the laminar and turbulent ranges of a two-phase seal is described and documented. The analyses, results, and computer codes are summarized.

Hughes, William F.↗
DOE OSTI2024

A Compact, Single Stage, >1 kV Medium-Voltage Line Impedance Stabilization Network

This paper presents the design of a single-phase, single-stage line impedance stabilization network (LISN) for medium-voltage (MV) applications. More than 1 kV rated widebandgap (WBG) power semiconductor switches are increasingly utilized in new, emerging power electronics energy systems to improve power density and efficiency. However, due to inherently fast-switching speeds, WBG switch modules emit considerable electromagnetic interference (EMI) (e.g., common mode (CM) or differential mode (DM)). State-of-the-art offers standardized LISN solutions to validate and certify the new energy system for electromagnetic compatibility (EMC). However, most are for low voltage applications (i.e., < 1 kV). MV LISNs (i.e., > 1 kV) are rare until recently and literature does not provide sufficient guidelines for designing and characterizing such devices. It has been a critical challenge for many scientists and engineers to reliably certify the emerging MV energy systems (e.g., electric ships and aircraft). This paper addresses such a technology gap. Specifically, a CISPR 16-1-2 compliant 50Ω/50μH LISN with 1.5kV, 75A and 30MHz measurement capability has been proposed. Detailed performance study versus non-linear parasitic parameters variations in MV inductors and capacitors have been done. Based on new understandings, novel techniques to intuitively mitigate unwanted parasitic have been proposed to develop the proposed LISN successfully. Thorough characterization of important LISN parameters are presented and factors influencing them are analyzed. A rigorous analysis, experimental tests, and in-depth comparisons over state-of-the-art have been made to validate the effectiveness. This is done through the state-of-the-art 300kVA MV EMI testbed.

42 ENGINEERING↗
NASA NTRS1980

The Space Telescope Observatory

The Space Telescope is an international astronomical observatory which will be placed into a low earth orbit in December 1983. The observatory will provide astronomers the opportunity to use five different instruments (wide field/planetary camera, faint object camera, high-resolution spectrograph, faint-object spectrograph, and high speed photometer), and to do astrometry with the use of the fine guidance sensors used primarily for pointing control. These instruments, the spectral range available above the earth's atmosphere, and the spatial resolution available from the combination of a near-diffraction limited 94-in. primary mirror and the stability provided by the Pointing Control System provide a tremendous potential to the astronomical community.

Bahcall, J. N.↗
NASA NTRS1986

Nonlinear lift control at high speed and high angle of attack using vortex flow technology

Nonlinear lift control at subsonic, transonic and low supersonic speeds owes its origin to the separated but organized vortical flows interacting with the wing upper surface. Since most of this flow originates near the wing or control-surface leading-edge, a variety of devices have been studied experimentally which interact with and/or control this flow in order to gain a beneficial effect. The benefits (effects) originally studied were only associated with lift enhancement. Whereas, now the studied benefits encompass performance increase, attention to changes in trimmed conditions and longitudinal stability, improvements in lateral stability, and the attendant variation with changing Mach number. For those devices that can be theoretically modeled, state-of-the-art computer codes have been used for device design and/or analysis. Comparisons at design and off-design conditions are presented for validation purposes.

Lamar, J. E.↗
NASA NTRS1992

The effectiveness of Coriolis dampening of convection during aircraft high-g arcs

Directional solidification data for metal samples in KC-135 parabolic maneuvers are examined to determine evidence for Coriolis dampening of convection. Microstructural and materials properties data are examined for iron carbon, immiscible, and superalloy systems. By comparison of low-g data and high-g data with those of one-g control samples, it is determined that there is no evidence that Coriolis dampening of convective flow is effective during the 1.8 g KC-135 high-g maneuvers. A first approximation model for the high-g arc is proposed. The model yields a centrifugal radius of 20,480 ft and an angular speed of 0.397 RPM. Comparison to centrifugal solidification experiments (for an equal acceleration) where Coriolis melt growth stabilization is significant indicates that the KC-135 high-g arc is less effective in dampening convection by a factor of 100. This large difference in Coriolis dampening of convection might be taken advantage of for experiments where separation of centrifugal acceeration and Coriolis acceleration is desirable.

Curreri, Peter A.↗