Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Hydro”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42

Quantitative Comparison of the Responses of Three Floating Platforms

This report presents a comprehensive dynamic-response analysis of three offshore floating wind turbine concepts. Models were composed of one 5-MW turbine supported on land and three 5-MW turbines located offshore on a tension leg platform, a spar buoy, and a barge. A loads and stability analysis adhering to the procedures of international design standards was performed for each model using the fully coupled time-domain aero-hydro-servo-elastic design code FAST with AeroDyn and HydroDyn. The concepts are compared based on the calculated ultimate loads, fatigue loads, and instabilities. The results of this analysis will help resolve the fundamental design trade-offs between the floating-system concepts.

17 WIND ENERGY↗

Unit Commitment Considering Generation Flexibility and Environmental Constraints

This paper proposes a new framework for power system unit commitment process, which incorporates the generation flexibility requirements and environmental constraints into the existing unit commitment algorithm. The generation flexibility requirements are to address the uncertainties with large amount of intermittent resources as well as with load and traditional generators, which causes real-time balancing requirements to be variable and less predictable. The proposed flexibility requirements include capacity, ramp and ramp duration for both upward and downward balancing reserves. The environmental constraints include emission allowance for fossil fuel-based generators and ecological regulations for hydro power plants. Calculation of emission rates is formulated. Unit commitment under this new framework will be critical to the economic and reliable operation of the power grid and the minimization of its negative environmental impacts, especially when high penetration levels of intermittent resources are being approached, as required by the renewable portfolio standards in many states.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Scalable subsurface inverse modeling of huge data sets with an application to tracer concentration breakthrough data from magnetic resonance imaging

When characterizing subsurface properties is crucial for reliable and cost-effective groundwater supply management and contaminant remediation. With recent advances in sensor technology, large volumes of hydro-geophysical and geochemical data can be obtained to achieve high-resolution images of subsurface properties. However, characterization with such a large amount of information requires prohibitive computational costs associated with “big data” processing and numerous large-scale numerical simulations. To tackle such difficulties, the Principal Component Geostatistical Approach (PCGA) has been proposed as a “Jacobian-free” inversion method that requires much smaller forward simulation runs for each iteration than the number of unknown parameters and measurements needed in the traditional inversion methods. PCGA can be conveniently linked to any multi-physics simulation software with independent parallel executions. In our paper, we extend PCGA to handle a large number of measurements (e.g. 106 or more) by constructing a fast preconditioner whose computational cost scales linearly with the data size. For illustration, we characterize the heterogeneous hydraulic conductivity (K) distribution in a laboratory-scale 3-D sand box using about 6 million transient tracer concentration measurements obtained using magnetic resonance imaging. Since each individual observation has little information on the K distribution, the data was compressed by the zero-th temporal moment of breakthrough curves, which is equivalent to the mean travel time under the experimental setting. Moreover, only about 2,000 forward simulations in total were required to obtain the best estimate with corresponding estimation uncertainty, and the estimated K field captured key patterns of the original packing design, showing the efficiency and effectiveness of the proposed method. This article is protected by copyright. All rights reserved.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Edge Dislocations Induce Improved Photocatalytic Efficiency of Colored TiO2

Titanium oxide is the most widely used material for photocatalytic applications due to its low cost and environmental friendliness. One of the grand challenges to improve its energy conversion efficiency is to utilize more visible light while inhibiting the recombination of photo-generated electrons and holes. We use a one-step hydro-solvothermal method to obtain colored ultra-fine nanowires of rutile and nanoparticles of anatase with edge dislocations, which induced broadened visible solar absorption (400-900 nm) and improved photocatalytic efficiency up to 1.8 times that of rutile or anatase without defects. Enhanced photocatalytic activity of these structures is demonstrated by photodegrading methylene blue measurements under simulated solar light irradiation. Results show the existence of Ti3+, induced by edge dislocations, and subsequent electronic band structure-property relationships. This work highlights a strategy for generating sufficient desired defects in TiO2 nanostructures, leading to broadened visible solar absorption and improved photocatalytic efficiency under visible light irradiation.

Ren, Peng↗

Supercritical Methanol Solvolysis and Catalysis for the Conversion of Delignified Woody Biomass into Light Alcohol Gasoline Bioblendstock

Supercritical methanol (SCM) solvolysis and catalysis has recently emerged as a promising pathway to produce gasoline-range light alcohols from woody biomass through staged depolymerization and hydro-deoxygenation (DHDO). Here, structure-property relationships of Cu"M"AlO x catalysts (M = Mg, Zr, and Ce) are examined for upgrading delignified hybrid poplar via SCM-DHDO. CuCeAlO x displays the highest activity, increasing the C 2 -C 7 alcohol production rate and selectivity by twofold in batch reactions, and >50% in semicontinuous reactions relative to the current state-of-the-art CuMgAlO x . The performance of CuCeAlOx is correlated with its high reducibility and acidity. Cu sintering and biogenic impurity poisoning are identified as possible deactivation mechanisms over 60 h of continuous testing. The gasoline-range SCM-DHDO products are comprised of primarily aliphatic alcohols that result in improved energy density and favorably reduced vapor pressure, relative to ethanol, with the tradeoff of nonsynergistic octane blending with conventional gasoline and lower oxidation stability. Overall, this work highlights the potential to produce suitable light oxygenates by SCM-DHDO processing for gasoline bioblendstock applications.

09 BIOMASS FUELS↗

Palladium/Ferrierite versus Palladium/SSZ‐13 Passive NOx Adsorbers: Adsorbate‐Controlled Location of Atomically Dispersed Palladium(II) in Ferrierite Determines High Activity and Stability**

Abstract Pd‐loaded FER and SSZ‐13 zeolites as low‐temperature passive NOx adsorbers (PNA) are compared under practical conditions. Vehicle cold start exposes the material to CO under a range of concentrations, necessitating a systematic exploration of the effect of CO on the performance of isolated Pd ions in PNA. The NO release temperature of both adsorbers decreases gradually with an increase in CO concentration from a few hundred to a few thousand ppm. This beneficial effect results from local nano‐“hot spot” formation during CO oxidation. Dissimilar to Pd/SSZ‐13, increasing the CO concentration above ≈1000 ppm improves the NOx storage significantly for Pd/FER, which was attributed to the presence of Pd ions in FER sites that are shielded from NOx. CO mobilizes this Pd atom to the NOx accessible position where it becomes active for PNA. This behavior explains the very high resistance of Pd/FER to hydrothermal aging: Pd/FER materials survive hydrothermal aging at 800 °C in 10 % H 2 O vapor for 16 hours with no deterioration in NOx uptake/release behavior. Thus, by allocating Pd ions to the specific microporous pockets in FER, we have produced (hydro)thermally stable and active PNA materials.

Khivantsev, Konstantin↗

Branched Aramid Nanofibers

Interconnectivity of components in three-dimensional networks (3DNs) is essential for stress transfer in hydrogels, aerogels, and composites. Entanglement of nanoscale components in the network relies on weak short-range intermolecular interactions. The intrinsic stiffness and rod-like geometry of nanoscale components limit the cohesive energy of the physical crosslinks in 3DN materials. Nature realizes networked gels differently using components with extensive branching. In this work, branched aramid nanofibers (BANFs) mimicking polymeric components of biological gels were synthesized to produce 3DNs with high efficiency stress transfer. Individual BANFs are flexible, with the number of branches controlled by base strength in the hydrolysis process. The extensive connectivity of the BANFs allows them to form hydro- and aerogel monoliths with an order of magnitude less solid content than rod-like nanocomponents. Branching of nanofibers also leads to improved mechanics of gels and nanocomposites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Palladium/Ferrierite versus Palladium/SSZ-13 Passive NOx Adsorbers: Adsorbate-Controlled Location of Atomically Dispersed Palladium(II) in Ferrierite Determines High Activity and Stability**

Pd-loaded FER and SSZ-13 zeolites as low-temperature passive NOx adsorbers (PNA) are compared under practical conditions. Vehicle cold start exposes the material to CO under a range of concentrations, necessitating a systematic exploration of the effect of CO on the performance of isolated Pd ions in PNA. The NO release temperature of both adsorbers decreases gradually with an increase in CO concentration from a few hundred to a few thousand ppm. This beneficial effect results from local nano-“hot spot” formation during CO oxidation. Dissimilar to Pd/SSZ-13, increasing the CO concentration above ˜1000 ppm improves the NOx storage significantly for Pd/FER, which was attributed to the presence of Pd ions in FER sites that are shielded from NOx. CO mobilizes this Pd atom to the NOx accessible position where it becomes active for PNA. This behavior explains the very high resistance of Pd/FER to hydrothermal aging: Pd/FER materials survive hydrothermal aging at 800°C in 10% H 2 O vapor for 16 hours with no deterioration in NOx uptake/release behavior. Therefore, by allocating Pd ions to the specific microporous pockets in FER, we have produced (hydro)thermally stable and active PNA materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effects of soybean varieties on life-cycle greenhouse gas emissions of biodiesel and renewable diesel

This study presents a life-cycle analysis (LCA) of the greenhouse gas (GHG) emissions of biodiesel (BD) and renewable diesel (RD) produced from soybean varieties with altered oil profiles and meal composition. The varieties evaluated include those with high oleic oil content (78% of oil being oleic oil vs. the current content of 25%), high lipid content (25% vs. the current content of 19%) or high protein content (45% vs. the current content of 35%). The results suggest that high-oleic soybean oil could reduce GHG emissions of RD by 1 g CO 2 e/MJ by reducing hydrogen consumption in the hydro-treating stage of RD production. With the default allocation method (mass-based allocation between oil and meal), changes in lipid and protein contents have negligible impacts on GHG emissions of BD/RD pathways. Since high-protein soybean meal has a higher nutrient value, we employed the market-based allocation for sensitivity analysis. Assuming a market price of $1.17/dry kg and an average of two substitute feeds with similar protein contents (corn gluten and fish meal), the allocation factor for soybean meal increases from 63 to 81%. Compared with the results for the case with commodity soybean using mass allocation, GHG emissions could be 1.9 and 1.8 g CO 2 e/MJ lower for BD and RD, respectively. In addition to product-level LCA, we employed a land-based LCA to evaluate the effect of soybean properties on product slates with the same land area and the associated displacement of conventional products. The results suggest that high-lipid soybeans may offer more GHG savings than other varieties as the higher BD/RD yield replaces more fossil diesel. © 2023 UChicago Argonne, LLC, Operator of Argonne National Laboratory and Northrup, Ag. Biofuels, Bioproducts and Biorefining published by Society of Industrial Chemistry and John Wiley & Sons Ltd.

09 BIOMASS FUELS↗

Hydrotreatment of Nylon 66 and Amide Model Compounds Over Sulfided NiMo Catalysts

Molybdenum sulfide-based catalysts, such as nickel–molybdenum on alumina (NiMoS x /Al 2 O 3 ), are widely used in hydrotreating and have potential for catalyzing waste plastic conversion via hydrogenolysis, yet their performance, such as reaction kinetics and network, for amide-rich polymer feeds is poorly defined. Here we combine Nylon 66 with the amide model compound, N,N-dibutylhexanediamide (DBDAD), to quantify hydrodeoxygenation (HDO) and hydrodenitrogenation (HDN) chemistry in a stirred batch reactor (53 bar H 2 , 280–320°C). DBDAD conversion is near-linear with time, indicating strong adsorption of the substrates on the active sites. Time-resolved product identification indicates parallel C─O first-cleavagedeoxygenation (DO) and C─N first-cleavagedenitrogenation (DN) sequences proceeding through amine and diol intermediates, respectively, to C 4 ─C 6 alkanes. Increasing temperature shifts selectivity toward DN, decreasing the initial r(DO)/r(DN) from 1.38 (280°C) to 0.69 (320°C), with an apparent activation energy of 173 kJ mol −1 for DBDAD conversion. At 300°C, nylon 66 converts faster than DBDAD, producing a complex mixture of oxygen- and nitrogen-containing species and an initial rate ratio r(DO)/r(DN) of 1.6. No heteroaromatic nitrogen products are detected by the method used. These results provide reaction pathways and product signatures relevant to hydro-processing catalysts exposed to polyamide-derived streams.

Nylon 66↗

Uncertainty quantification for evaluating the impacts of fracture zone on pressure build-up and ground surface uplift during geological CO₂ sequestration

A series of numerical test cases reflecting broad and realistic ranges of geological formation and preexisting fault properties was developed to systematically evaluate the impacts of preexisting faults on pressure buildup and ground surface uplift during CO₂ injection. Numerical test cases were conducted using a coupled hydro-geomechanical simulator, eSTOMP (extreme-scale Subsurface Transport over Multiple Phases). For efficient sensitivity analysis and reliable construction of a reduced-order model, a quasi-Monte Carlo sampling method was applied to effectively sample a high-dimensional input parameter space to explore uncertainties associated with hydrologic, geologic, and geomechanical properties. The uncertainty quantification results show that the impacts on geomechanical response from the pre-existing faults mainly depend on reservoir and fault permeability. When the fault permeability is two to three orders of magnitude smaller than the reservoir permeability, the fault can be considered as an impermeable block that resists fluid transport in the reservoir, which causes pressure increase near the fault. When the fault permeability is close to the reservoir permeability, or higher than 10⁻¹⁵ m² in this study, the fault can be considered as a conduit that penetrates the caprock, connecting the fluid flow between the reservoir and the upper rock.

CO₂ geological sequestration↗

Active layer hydrology in an arctic tundra ecosystem: quantifying water sources and cycling using water stable isotopes

Climate change and thawing permafrost in the Arctic will significantly alter landscape hydro-geomorphology and the distribution of soil moisture, which will have cascading effects on climate feedbacks (CO 2 and CH 4 ) and plant and microbial communities. Fundamental processes critical to predicting active layer hydrology are not well understood. This study applied water stable isotope techniques (δ 2 H and δ 18 O) to infer sources and mixing of active layer waters in a polygonal tundra landscape in Barrow, Alaska (USA), in August and September of 2012. Results suggested that winter precipitation did not contribute substantially to surface waters or subsurface active layer pore waters measured in August and September. Summer rain was the main source of water to the active layer, with seasonal ice melt contributing to deeper pore waters later in the season. Surface water evaporation was evident in August from a characteristic isotopic fractionation slope (δ 2 H vs δ 18 O). Freeze-out isotopic fractionation effects in frozen active layer samples and textural permafrost were indistinguishable from evaporation fractionation, emphasizing the importance of considering the most likely processes in water isotope studies, in systems where both evaporation and freeze-out occur in close proximity. The fractionation observed in frozen active layer ice was not observed in liquid active layer pore waters. Such a discrepancy between frozen and liquid active layer samples suggests mixing of meltwater, likely due to slow melting of seasonal ice. In conclusion, this research provides insight into fundamental processes relating to sources and mixing of active layer waters, which should be considered in process-based fine-scale and intermediate-scale hydrologic models.

54 ENVIRONMENTAL SCIENCES↗

Understanding coastal wetland hydrology with a new regional‐scale, process‐based hydrological model

Abstract Coastal wetlands represent an ecotone between ocean and terrestrial ecosystems, providing important services, including flood mitigation, fresh water supply, erosion control, carbon sequestration, and wildlife habitat. The environmental setting of a wetland and the hydrological connectivity between a wetland and adjacent terrestrial and aquatic systems together determine wetland hydrology. Yet little is known about regional‐scale hydrological interactions among uplands, coastal wetlands, and coastal processes, such as tides, sea level rise, and saltwater intrusion, which together control the dynamics of wetland hydrology. This study presents a new regional‐scale, physically based, distributed wetland hydrological model, PIHM‐Wetland, which integrates the surface and subsurface hydrology with coastal processes and accounts for the influence of wetland inundation on energy budgets and evapotranspiration (ET). The model was validated using in situ hydro‐meteorological measurements and Moderate Resolution Imaging Spectroradiometer (MODIS) ET data for a forested and herbaceous wetland in North Carolina, USA, which confirmed that the model accurately represents the major wetland hydrological behaviours. Modelling results indicate that topographic gradient is a primary control of groundwater flow direction in adjacent uplands. However, seasonal climate patterns become the dominant control of groundwater flow at lower coastal plain and land–ocean interface. We found that coastal processes largely influence groundwater table (GWT) dynamics in the coastal zone, 300 to 800 m from the coastline in our study area. Among all the coastal processes, tides are the dominant control on GWT variation. Because of inundation, forested and herbaceous wetlands absorb an additional 6% and 10%, respectively, of shortwave radiation annually, resulting in a significant increase in ET. Inundation alters ET partitioning through canopy evaporation, transpiration, and soil evaporation, the effect of which is stronger in cool seasons than in warm seasons. The PIHM‐Wetland model provides a new tool that improves the understanding of wetland hydrological processes on a regional scale. Insights from this modelling study provide benchmarks for future research on the effects of sea level rise and climate change on coastal wetland functions and services.

Zhang, Yu↗

Efficient co-solution of time step size and independent state in simulations of fluid-driven fracture propagation with embedded meshes

Here we present an efficient time-continuation scheme for fluid-driven fracture propagation problems in the extended finite element method framework. The approach applies a monolithic solution strategy to a fully coupled and implicit approximation of hydro-mechanical systems in conjunction with simultaneous linear elastic propagation of multiple fractures. At the end of each time step, the process ensures that the weakest fracture tip is in an equilibrium propagation regime. Furthermore, the solution process provides an initialization procedure for the newly created fracture spaces and an a priori estimate of the stress intensity factor growth rate, improving simulation robustness, and efficiency. The solution process is validated using the Kristianovich-Geertsma-de Klerk analytical solution under the toughness- and viscosity-dominated regimes. It is also extended to and demonstrated on problems with multiple fractures undergoing simultaneous propagation with stress shadow interactions. Numerical examples demonstrate that the solution process can reduce the required computational cost by one order of magnitude compared to other existing methods.

42 ENGINEERING↗

β-Octabromo- and β-Octakis(trifluoromethyl)isocorroles: New Sterically Constrained Macrocyclic Ligands

Here, we present a study of the acid-induced demetalation of two sterically hindered copper corroles, Cu β-octabromo-meso-triphenylcorrole (Cu[Br 8 TPC]) and β-octakis(trifluoromethyl)-meso-tris(p-methoxyphenyl)corrole (Cu[(CF 3 ) 8 TpOMePC]). Unlike reductive demetalation, which affords the free-base β-octabromocorrole, demetalation of Cu[Br 8 TPC] under non- reductive conditions (CHCl 3 /H 2 SO 4 ) resulted in moderate yields of free-base 5- and 10-hydroxy isocorroles. The isomeric free bases could be complexed to Co II and Ni II , affording stable complexes. Only reductive demetalation was found to work for Cu[(CF 3 ) 8 TpOMePC], affording a highly saddled, hydrated corrole, H 3 [5-OH,10-H-(CF 3 ) 8 TpOMePC], where the elements of water had added across C5 and C10. Interaction of this novel free base with Co II resulted in Co[iso-10-H-[CF 3 ) 8 TpOMePC], a Co II 10-hydro isocorrole. Finally, the new metal complexes were all characterized by single-crystal X-ray diffraction analysis and, despite their sterically hindered nature, were found to exhibit almost perfectly planar isocorrole cores.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Characterization of Free Surface-Bound and Entrapped Water Environments in Poly(N-Isopropyl Acrylamide) Hydrogels via 1H HRMAS PFG NMR Spectroscopy

We found that different water environments in poly(N-isopropyl acrylamide) (PNIPAAm) hydrogels are identified and characterized using 1 H high resolution magic angle spinning (HRMAS) nuclear magnetic resonance (NMR). Local water environments corresponding to a “free” highly mobile species, along with waters showing restricted dynamics are resolved in these swollen hydro-gels. For photo-initiated polymerized PNIPAAm gels, an additional entrapped water species is observed. Spin–spin R 2 relaxation experiments support the argument of reduced mobility in the restricted and entrapped water species. Furthermore, by combining pulse field gradient techniques with HRMAS NMR it is possible to directly measure the self-diffusion rate for these different water environments. The behavior of the heterogeneous water environments through the lower critical solution temperature transition is described.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Safe passage of American Eels through a novel hydropower turbine

Abstract Objective Study the effects of downstream passage through a novel turbine designed for fish safety, the Restoration Hydro Turbine (RHT), on American Eels Anguilla rostrata in a recirculating turbine test facility. Methods A 55‐cm‐diameter RHT was operated under 10 m of hydraulic head and 667 revolutions/min. In total, 131 eels were passed through the turbine and 43 eels were used as experimental controls (length = 33.9–65.5 cm). High‐speed video of passage through the runner region was captured for 89% of turbine‐passed eels, and injury and behavioral effects were recorded immediately before and after passage, as well as after a 48‐h holding period. A subset of 37 eels was additionally examined with X‐ray imaging for internal injuries. Result The 48‐h survival rate for both treatment and control groups was 100%, with no major internal or external injuries present after the holding period. Conclusion This is a substantial improvement over eel survival rates through conventional Kaplan and Francis turbines, which may range from 40% to 95%, and suggests that hydropower turbines designed for safe downstream fish passage could be implemented without major impacts to eels.

59 BASIC BIOLOGICAL SCIENCES↗

Temperature response and brine availability to heated boreholes in bedded salt

Abstract There is a growing need for disposal of high‐level nuclear waste. To reduce uncertainty associated with brine availability to repository excavations in salt formations, a collaboration between Sandia, Los Alamos, and Lawrence Berkeley National Laboratories is performing a series of borehole‐scale coupled process tests. Here, we report on the first round of the Brine Availability Test in Salt (BATS) project, a “shakedown” experiment called Phase 1s. Experimental testing included placing a resistive heater, a 260‐W radiative heater, and a 750‐W radiative heater within previously drilled horizontal boreholes at the Waste Isolation Pilot Plant (WIPP) while monitoring temperature and water inflow. The experiments successfully achieved the targeted temperature of 120 °C when using the 750‐W radiative heater. Simulations using FEHM (Finite Element Heat and Mass transfer code) and TOUGH‐FLAC (Transport Of Unsaturated Groundwater and Heat–Fast Lagrangian Analysis of Continua) were able to accurately predict the coupled thermo–hydro–mechanical–chemical response of salt, matching the observed temperature and brine production. Due to the extremely low permeability of salt, these systems take many years to reach steady state when perturbed by mining activities. Long‐term numerical simulations are used to develop the initial pressure and saturation conditions. The inclusion of a damaged rock zone with higher permeability around the borehole also affects the saturation and pressure distributions and plays an important role in dissipating the potential for thermal pressurization. Knowledge gained from this round of experimentation and simulation will be used to conduct the next BATS project experiment in new boreholes at WIPP.

58 GEOSCIENCES↗