Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Frequency control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42
All sourcesNASA NTRSDOE OSTI
NASA NTRS2007

Development of Aeroservoelastic Analytical Models and Gust Load Alleviation Control Laws of a SensorCraft Wind-Tunnel Model Using Measured Data

Aeroservoelastic (ASE) analytical models of a SensorCraft wind-tunnel model are generated using measured data. The data was acquired during the ASE wind-tunnel test of the HiLDA (High Lift-to-Drag Active) Wing model, tested in the NASA Langley Transonic Dynamics Tunnel (TDT) in late 2004. Two time-domain system identification techniques are applied to the development of the ASE analytical models: impulse response (IR) method and the Generalized Predictive Control (GPC) method. Using measured control surface inputs (frequency sweeps) and associated sensor responses, the IR method is used to extract corresponding input/output impulse response pairs. These impulse responses are then transformed into state-space models for use in ASE analyses. Similarly, the GPC method transforms measured random control surface inputs and associated sensor responses into an AutoRegressive with eXogenous input (ARX) model. The ARX model is then used to develop the gust load alleviation (GLA) control law. For the IR method, comparison of measured with simulated responses are presented to investigate the accuracy of the ASE analytical models developed. For the GPC method, comparison of simulated open-loop and closed-loop (GLA) time histories are presented.

Walter A. Silva↗
NASA NTRS1974

Traffic control system and method

Frequency of carrier received by aircraft is measured and compared with reference to indicate magnitude of Doppler shift. One Doppler frequency range is selected and indicated by digital signal. Difference between frequency is offset of apparent carrier frequency transmitted by aircraft.

Laughlin, C. R.↗
DOE OSTI2020

A variable X-ray chopper system for phase-sensitive detection in synchrotron X-ray scanning tunneling microscopy

An ultra-high-vacuum compatible X-ray chopper system has been designed, constructed and integrated into the XTIP beamline at the Advanced Photon Source at Argonne National Laboratory. The XTIP beamline can operate at soft X-ray energies from 400 eV to 1900 eV while providing a focused beam down to about 10 µm × 10 µm into the synchrotron X-ray scanning tunneling microscopy (SX-STM) endstation instrument. The X-ray chopper is a critical component for separating topographic information from chemical information in SX-STM through phase-sensitive current detection. Depending on the experimental needs, the modulation frequency can be controlled from 100 Hz to 10 kHz. In addition, the chopper system is fully bakeable and can achieve a base pressure of 10 -10 mbar. Facilities for active water cooling have been designed, but passive cooling through copper braids has been shown to be sufficient at standard chopping frequencies. Using an Fe/Al 2 O 3 /CoAl(111) sample, the separation of the SX-STM current into a chemical component and a stable feedback signal is demonstrated.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2022

Decentralized Distribution System Restoration with Grid-Forming/Following Inverter-Based Resources

The high penetration of distributed energy resources (DERs) in active distribution systems has posed challenges to the centralized distribution system restoration (DSR) strategies in current practice. On the other hand, the advancement in smart inverter technologies enables the bottom-up restoration capability. This paper is motivated to develop a 3-layered hierarchical framework for decentralized DSR, based on the grid-forming (GFM) and grid-following (GFL) grid-edge inverters. The first layer presents the tertiary control, which determines the load pickup schedule and generation dispatch of DERs, using the alternating direction method of the multipliers algorithm. The second layer consists of two control functions: GFM control, which regulates voltage and frequency, establishing a stable grid for GFL inverters to follow; and GFL control, which regulates the real and reactive power. In the third layer, the primary control is proposed to regulate the inverter voltage and current, which is developed based on the virtual oscillator control (VOC). Furthermore, the developed framework is tested in the modified IEEE 13-node test feeder. Two scenarios of grid-connected and islanded operating modes are designed, and simulation results demonstrate the effectiveness of decentralized DSR strategies for controlling grid-edge inverters to enhance the distribution system resilience.

24 POWER TRANSMISSION AND DISTRIBUTION↗
NASA NTRS1982

Controller design for flexible, distributed parameter mechanical arms via combined state space and frequency domain techniques

The potential benefits of the ability to control more flexible mechanical arms are discussed. A justification is made in terms of speed of movement. A new controller design procedure is then developed to provide this capability. It uses both a frequency domain representation and a state variable representation of the arm model. The frequency domain model is used to update the modal state variable model to insure decoupled states. The technique is applied to a simple example with encouraging results.

Book, W. J.↗
NASA NTRS1998

Sensor/Actuator Selection for Gust and Turbulence Control

From aircraft fuselages and space stations to vacuum cleaners and automobiles, active control of noise and/or vibration has come of age. Determining the number of active control devices (e.g. actuators) to be placed and where they are to be placed is the prototypical location problem. However, unlike typical location problems, where the customer is readily identified and is actively engaged in the assessment of the performance of the chosen locations, the customers that active control devices serve are not so easily identified and their impact on system performance issues may be unclear. For example, consider the problem of where to locate actuators to attenuate cabin noise in a propeller driven aircraft. Clearly, the ultimate customers are the passengers who will travel in these aircraft. But to decide whether one set of actuator locations is better than another it is unlikely we will ask passengers to fly in the aircraft and fill out a questionnaire about noise levels. Instead a set of sensors (pseudo-customers) are placed and the system performance of the actuators, as measured by these sensors, is recorded. Hence, we have yet another location problem. How many sensors should there be and where should they be located? In many instances collocation of sensors and actuators is the answer but in other instances it is not. A variety of approaches have been taken to address these sensor/actuator location problems. With regard to damping vibrations in truss structures (space station prototypes) it was formulated a new noxious location problem and generated high-quality solutions with a combination of LP-relaxations and heuristic search procedures. Other related efforts are summarized the actuator location problem for a single frequency interior noise control problem was examined for an idealized aircraft cabin. A tabu search procedure was shown to generate better locations for the actuators than a modal decomposition approach. The model was extended to include multi-frequency information. The sensor location problem is addressed. In the latter article a reactive tabu search scheme was shown to dominate a static tabu search approach. Our focus here is to determine locations to control and/or sense vibrations on a truss structure. However, instead of using one of the earlier optimization models referenced in the above paragraph we adopt an experimental design approach.

Kincaid, Rex K.↗
NASA NTRS1979

Alternatives for jet engine control

The research is classified in two categories: (1) the use of modern multivariable frequency domain methods for control of engine models in the neighborhood of a set-point, and (2) the use of nonlinear modelling and optimization techniques for control of engine models over a more extensive part of the flight envelope. Progress in the first category included the extension of CARDIAD (Complex Acceptability Region for Diagonal Dominance) methods developed with the help of the grant to the case of engine models with four inputs and four outputs. A suitable bounding procedure for the dominance function was determined. Progress in the second category had its principal focus on automatic nonlinear model generation. Simulations of models produced satisfactory results where compared with the NASA DYNGEN digital engine deck.

Sain, M. K.↗
NASA NTRS1991

A simulation evaluation of a four-engine jet transport using engine thrust modulation for flightpath control

The use of throttle control laws to provide adequate flying qualities for flight path control in the event of a total loss of conventional flight control surface use was evaluated. The results are based on a simulation evaluation by transport research pilots of a B-720 transport with visual display. Throttle augmentation control laws can provide flight path control capable of landing a transport-type aircraft with up to moderate levels of turbulence. The throttle augmentation mode dramatically improves the pilots' ability to control flight path for the approach and landing flight condition using only throttle modulation. For light turbulence, the average Cooper-Harper pilot rating improved from unacceptable to acceptable (a pilot rating improvement of 4.5) in going from manual to augmented control. The low frequency response characteristics of the engines require a considerably different piloting technique. The various techniques used by the pilot resulted in considerable scatter in data. Many pilots readily adapted to a good piloting technique while some had difficulty. A new viable approach is shown to provide independent means of redundancy of transport aircraft flight path control.

Gilyard, Glenn B.↗
NASA NTRS2013

Wireless Chalcogenide Nanoionic-Based Radio-Frequency Switch

A new nonvolatile nanoionic switch is powered and controlled through wireless radio-frequency (RF) transmission. A thin layer of chalcogenide glass doped with a metal ion, such as silver, comprises the operational portion of the switch. For the switch to function, an oxidizable electrode is made positive (anode) with respect to an opposing electrode (cathode) when sufficient bias, typically on the order of a few tenths of a volt or more, is applied. This action causes the metal ions to flow toward the cathode through a coordinated hopping mechanism. At the cathode, a reduction reaction occurs to form a metal deposit. This metal deposit creates a conductive path that bridges the gap between electrodes to turn the switch on. Once this conductive path is formed, no further power is required to maintain it. To reverse this process, the metal deposit is made positive with respect to the original oxidizable electrode, causing the dissolution of the metal bridge thereby turning the switch off. Once the metal deposit has been completely dissolved, the process self-terminates. This switching process features the following attributes. It requires very little to change states (i.e., on and off). Furthermore, no power is required to maintain the states; hence, the state of the switch is nonvolatile. Because of these attributes the integration of a rectenna to provide the necessary power and control is unique to this embodiment. A rectenna, or rectifying antenna, generates DC power from an incident RF signal. The low voltages and power required for the nanoionic switch control are easily generated from this system and provide the switch with a novel capability to be operated and powered from an external wireless device. In one realization, an RF signal of a specific frequency can be used to set the switch into an off state, while another frequency can be used to set the switch to an on state. The wireless, miniaturized, and nomoving- part features of this switch make it suitable for applications such as integration into garments, RFID (radio-frequency identification) tags, and conformal structures (e.g., aircraft wings, sounding rockets contours, etc). In the case of RFID tags the innovation will provide countermeasures to attempts for identity theft and other uninvited attempts for retrieval of information. It could also be applicable to the automotive industry as well as the aerospace industry for collision avoidance and phased array radar systems, respectively

Nessel, James↗
NASA NTRS1992

Frequency monitoring a LIDAR transmitter for pulse-by-pulse analysis and control

An electronic technique is described whereby the heterodyne mixing frequency of a pulsed LIDAR transmitter is displayed on a color-coded linear bar graph. The technique is of great utility for manually fine tuning the laser output frequency when the use of conventional frequency counters and spectrum analyzers is impractical in a rapidly firing system.

Esproles, Carlos↗
NASA NTRS1995

Experimental evaluation of open-loop UpLink Power Control using ACTS

The present investigation deals with the implementation of open-loop up-link power control using a beacon signal in the down-link frequency band as the control parameter. A power control system was developed and tested using the ACTS satellite. ACTS carries beacon signals in both up- and down-link bands with which the relationship between the up- and down-link fading can be established. A power controlled carrier was transmitted to the ACTS satellite from a NASA operated ground station and the transponded signal was received at COMSAT Laboratories using a terminal that was routinely used to monitor the two ACTS beacon signals. The experiment ran for a period of approximately six months and the collected data were used to evaluate the performance of the power control system. A brief review of propagation factors involved in estimating the up-link fade using a beacon signal in the down-link band are presented. The power controller design and the experiment configuration are discussed. Results of the experiment are discussed.

Dissanayake, Asoka↗
NASA NTRS2006

Influence of Space Flight Factors on the Genetic Properties of Streptomyces Lividans 66 (PIJ702)

Gram-positive Streptomyces bacteria display genetic instability in response to external factors. Strain S. lividans 66 harbors the multicopy plasmid pIJ702 with selective and differential marker genes for antibiotic thiostrepton resistance and melanin production. Culture plates of modified ISP agar medium with and without thiostrepton were flown on Foton-M2. Suboptimal flight temperatures, which were simulated for asynchronous ground controls, resulted in slow growth and failure to differentiate and sporulate. Flight samples and asynchronous controls showed a high frequency of failing to express plasmid markers compared to laboratory controls. This was associated with loss of plasmid DNA and likely resulted from suboptimal temperatures for flight cultures and controls. Neither restriction fragment length polymorphism, nor polymerase chain reaction amplification coupled with denaturing gradient gel electrophoresis, revealed differences between pIJ702 DNA from flight vs. control clones. Mutations of the plasmid marker genes resulting from specific spaceflight factors, e.g., microgravity and radiation, were not detected.

Tabakov, V. Yu.↗