Results for “Experiment Optimization” — Page 42

NASA NTRS2005

"Layers in the Equatorial Mesosphere, Motions and Aerosol Rocket and Radar Study (LEMMA)"

Our role in the LEMMA rocket and radar measurement program had several components corresponding to the various phases of the research effort. Our initial efforts focused on definition of the experimental configuration and measurement requirements following the decision to move the experiment to Kwajalein. At this stage of the research, the PI of this subtask consulted with the project PI, Dr. Gerald Lehmacher, and other participants in defining the atmospheric conditions that would allow optimal measurements and the radar modes that would best characterize the structures we hoped to observe. This proved to be a challenge, as the ALTAIR radar, despite its substantial capabilities, did not have a representative suite of software control and analysis capabilities. Once the experiment and timing were defined, our role shifted to numerical characterization of potential radar backscatter and in situ turbulence signatures accompanying various dynamical processes. Following completion of the measurement program, we supported the analysis and interpretation of the experimental data.

Fritts, D. C.↗

NASA NTRS1984

Experiments with phase transitions at very high pressure

A diamond anvil cell is described which was developed for studying hydrogen and other materials to pressure above 100 PGa, including measurements at low temperature. The benefits of X-ray diffraction using synchrotron radiation and using a fixed anode source are examined as well as the optimization of X-ray diffraction at low temperature. A Ge diode detector was incorporated into apparatus for measuring optical absorption, reflectance, and fluorescence in order to enable luminescence studies and Raman spectra were obtained. Results of experiments on Si, Ge, GaP, InAs, hydrogen, benzene, nitrogen, graphite, and the superconductor CeCu2Si2 are given.

Spain, I. L.↗

NASA NTRS1973

Two concepts for the reduction of payload attitude slewing times.

The concepts presented are particularly valuable in sounding rocket applications, where experiment data-gathering time above the atmosphere is measured in minutes per flight. One concept is a practical nonlinear control law for slewing a payload in one axis, with performance that approaches time-optimal as the uncertainty in angular acceleration approaches zero. The second concept is a practical transformation-of-coordinates system allowing slewing about an axis not coincident with any of the three control axes of the payload, so that the payload experiment axis may move along the great circle arc containing the initial and terminal target points. Implementation of both concepts is facilitated by the availability of variable-thrust cold-gas thrustors. Both concepts can result in significant reductions in slewing times compared with more conventional systems.

Riley, D. C.↗

NASA NTRS1974

AAFE man-made noise experiment project. Volume 2: Project and experiment discussions

An experiment for the acquisition and processing of man-made noise interference data on earth orbital altitudes is discussed. The objectives of the project are to confirm the results of analytical studies concerning radio frequency man-made noise in space. It is stated that the measurements of the amounts and types of noise in frequency bands of interest could allow the allocation and utilization of frequencies to be optimized and would also contribute to the engineering objective of optimizing flight receiving systems. A second objective of the project was to design and fabricate a noise measuring receiver which would demonstrate the feasibility of the experiment design under the project. The procedures for acquiring and processing the electromagnetic radiation data are discussed.

Source record↗

NASA NTRS1990

Containerless experiments in fluid physics in microgravity

The physical phenomena associated with the behavior of liquid samples freely suspended in low gravity must be thoroughly understood prior to undertaking detailed scientific studies of the materials under scrutiny. The characteristics of molten specimens under the action of containerless positioning stresses must be identified and separated from the specific phenomena relating to the absence of an overwhelming gravitational field. The strategy designed to optimize the scientific return of reliable experimental data from infrequent microgravity investigations should include the gradual and logical phasing of more sophisticated studies building on the accumulated results from previous flight experiments. Lower temperature fluid physics experiments using model materials can provide a great deal of information that can be useful in analyzing the behavior of high temperature melts. The phasing of the experimental capabilities should, therefore, also include a gradual build-up of more intricate and specialized diagnostic instrumentation and environmental control and monitoring capabilities. Basic physical investigations should also be distinguished from specific materials technology issues. The latter investigations require very specific high temperature (and high vacuum) devices that must be thoroughly mastered on the ground prior to implementing them in space.

Trinh, E. H.↗

NASA NTRS1976

Overall evaluation of LANDSAT (ERTS) follow-on imagery for cartographic application

The author has identified the following significant results. The NASA/Cousteau experiment showed that under suitable conditions and with calibration data, the bottom of clear tropical seas can be mapped with LANDSAT to a depth of 22 meters with a root-mean-square error of about 10 percent. This application required the high gain setting of band 4 of the MSS. The experiment also confirmed that a somewhat lower waveband than band 4 would increase the water penetration capability of future LANDSATS. Other experiments illustrated by the reprinting of upper Chesapeake Bay indicate that the original LANDSAT signals must be modulated and optimized for the photographic and lithographic processes. Work by the Canadian mapping agency indicates significant improvements in the control identification and geometric accuracy of LANDSAT cartographic applications.

Colvocoresses, A. P.↗

NASA NTRS1976

Mass spectrometry of aerospace materials

Mass spectrometry is used for chemical analysis of aerospace materials and contaminants. Years of analytical aerospace experience have resulted in the development of specialized techniques of sampling and analysis which are required in order to optimize results. This work has resulted in the evolution of a hybrid method of indexing mass spectra which include both the largest peaks and the structurally significant peaks in a concise format. With this system, a library of mass spectra of aerospace materials was assembled, including the materials responsible for 80 to 90 percent of the contamination problems at Goddard Space Flight Center during the past several years.

Colony, J. A.↗

NASA NTRS1983

Space Station and the life sciences

Previous fundamental research in space life sciences is examined, and consideration is devoted to studies relevant to Space Station activities. Microgravity causes weight loss, hemoconcentration, and orthostatic intolerance when astronauts returns to earth. Losses in bone density, bone calcium, and muscle nitrogen have also been observed, together with cardiovascular deconditioning, fluid-electrolyte metabolism alteration, and space sickness. Experiments have been performed with plants, bacteria, fungi, protozoa, tissue cultures, invertebrate species, and with nonhuman vertebrates, showing little effect on simple cell functions. The Spacelab first flight will feature seven life science experiments and the second flight, two. Further studies will be performed on later flights. Continued life science studies to optimize human performance in space are necessary for the efficient operation of a Space Station and the assembly of large space structures, particularly in interaction with automated machinery.

White, R. J.↗

NASA NTRS1986

Broadcasting satellite service synthesis using gradient and cyclic coordinate search procedures

Two search techniques are considered for solving satellite synthesis problems. Neither is likely to find a globally optimal solution. In order to determine which method performs better and what factors affect their performance, we design an experiment and solve the same problem under a variety of starting solution configuration-algorithm combinations. Since there is no randomization in the experiment, we present results of practical, rather than statistical, significance. Our implementation of a cyclic coordinate search procedure clearly finds better synthesis solutions than our implementation of a gradient search procedure does with our objective of maximizing the minimum C/I ratio computed at test points on the perimeters of the intended service areas. The length of the available orbital arc and the configuration of the starting solution are shown to affect the quality of the solutions found.

Reilly, C. H.↗

NASA NTRS1994

Design and aerodynamic performance evaluation of a high-work mixed flow turbine stage

As axial and radial turbine designs have been pushed to their aerothermodynamic and mechanical limits, the mixed-flow turbine (MFT) concept has been projected to offer performance and durability improvements, especially when ceramic materials are considered. The objective of this NASA/U.S. Army sponsored mixed-flow turbine (AMFT) program was to determine the level of performance attainable with MFT technology within the mechanical constraints of 1997 projected ceramic material properties. The MFT geometry is similar to a radial turbine, exhibiting a large radius change from inlet to exit, but differing in that the inlet flowpath is not purely radial, nor axial, but mixed; it is the inlet geometry that gives rise to the name 'mixed-flow'. The 'mixed' orientation of the turbine inlet offers several advantages over radial designs by allowing a nonzero inlet blade angle yet maintaining radial-element blades. The oblique inlet not only improves the particle-impact survivability of the design, but improves the aerodynamic performance by reducing the incidence at the blade inlet. The difficulty, however, of using mixed-flow geometry lies in the scarcity of detailed data and documented design experience. This paper reports the design of a MFT stage designed with the intent to maximize aerodynamic performance by optimizing design parameters such as stage reaction, rotor incidence, flowpath shape, blade shape, vane geometry, and airfoil counts using 2-D, 3-D inviscid, and 3-D viscous computational fluid dynamics code. The aerodynamic optimization was accomplished while maintaining mechanical integrity with respect to vibration and stress levels in the rotor. A full-scale cold-flow rig test was performed with metallic hardware fabricated to the specifications of the hot ceramic geometry to evaluate the stage performance.

Neri, Remo N.↗

NASA NTRS1994

Evaluation of sensor placement algorithms for on-orbit identification of space platforms

Anticipating the construction of the international space station, on-orbit modal identification of space platforms through optimally placed accelerometers is an area of recent activity. Unwanted vibrations in the platform could affect the results of experiments which are planned. Therefore, it is important that sensors (accelerometers) be strategically placed to identify the amount and extent of these unwanted vibrations, and to validate the mathematical models used to predict the loads and dynamic response. Due to cost, installation, and data management issues, only a limited number of sensors will be available for placement. This work evaluates and compares four representative sensor placement algorithms for modal identification. Most of the sensor placement work to date has employed only numerical simulations for comparison. This work uses experimental data from a fully-instrumented truss structure which was one of a series of structures designed for research in dynamic scale model ground testing of large space structures at NASA Langley Research Center. Results from this comparison show that for this cantilevered structure, the algorithm based on Guyan reduction is rated slightly better than that based on Effective Independence.

Glassburn, Robin S.↗

NASA NTRS1998

Distributed Control with Collective Intelligence

We consider systems of interacting reinforcement learning (RL) algorithms that do not work at cross purposes , in that their collective behavior maximizes a global utility function. We call such systems COllective INtelligences (COINs). We present the theory of designing COINs. Then we present experiments validating that theory in the context of two distributed control problems: We show that COINs perform near-optimally in a difficult variant of Arthur's bar problem [Arthur] (and in particular avoid the tragedy of the commons for that problem), and we also illustrate optimal performance in the master-slave problem.

Wolpert, David H.↗

NASA NTRS2000

Performance characterization of an automated system for robot configuration synthesis

We describe the results of several experiments aimed at understanding the performance, behavior, and limitations of Darwin2K, an automated system for robot configuration synthesis and optimization.

evolutionary design automated synthesis robotics↗

NASA NTRS2012

Identification of Robust Terminal-Area Routes in Convective Weather

Convective weather is responsible for large delays and widespread disruptions in the U.S. National Airspace System, especially during summer. Traffic flow management algorithms require reliable forecasts of route blockage to schedule and route traffic. This paper demonstrates how raw convective weather forecasts, which provide deterministic predictions of the vertically integrated liquid (the precipitation content in a column of airspace) can be translated into probabilistic forecasts of whether or not a terminal area route will be blocked. Given a flight route through the terminal area, we apply techniques from machine learning to determine the likelihood that the route will be open in actual weather. The likelihood is then used to optimize terminalarea operations by dynamically moving arrival and departure routes to maximize the expected capacity of the terminal area. Experiments using real weather scenarios on stormy days show that our algorithms recommend that a terminal-area route be modified 30% of the time, opening up 13% more available routes that were forecast to be blocked during these scenarios. The error rate is low, with only 5% of cases corresponding to a modified route being blocked in reality, whereas the original route is in fact open. In addition, for routes predicted to be open with probability 0.95 or greater by our method, 96% of these routes (on average over time horizon) are indeed open in the weather that materializes

Pfeil, Diana Michalek↗

NASA NTRS2000

Modeling of dense reactive granular flows

Because of the lack of fundamental knowledge of both the fluid mechanical and thermal behavior of multiphase flow systems, the design of these processes has been necessarily based on empirical correlations and experiments performed in laboratory or pilot scale units. Detailed models and simulations of these systems would allow for the optimization of the processes and their scaling, without the need for expensive and time consuming testing. In this paper, we present the proposed hydrodynamic model in detail.

granular↗

NASA NTRSDate not supplied

Scaled Aeroelastic Wind Tunnel Model Design with Topology Optimization

The goal of this work is to use numerical aeroelastic topology optimization to design flutter models to be tested in the Transonic Dynamics Tunnel, as part of an envisioned validation experiment for transonic flutter. The topological design develops the structural details of a variable-thickness aluminum plate located at the camber line of a scaled transport aircraft model, in order to satisfy the various conflicting design requirements, including a prescribed flutter boundary, flutter frequency, and static stress levels. Four designs are demonstrated here, where it is shown that the simultaneous design of a cylindrical tip store can help ease the conflict between low stiffness (to allow a wing to flutter in the tunnel envelope) and high strength (to ensure safe structural response). The tip store complicates the geometrical features of the wing, however, and is generally undesirable from the vantage point of a validation experiment.

Aeroelasticity↗

NASA NTRSDate not supplied

Hazards of Lunar Surface Exploration: Determining the Immunogenicity/Allergenicity of Lunar Dust

Although infrequent, there have been Apollo program reports of lunar dust (LD) exposure leading to notable upper respiratory symptoms in select crewmembers. Possible mechanisms include particulate irritation, oxidization and release of noxious gas, or legitimate adaptive immune-mediated response. Although sterile non-protein matter would not be expected to be an allergen, one Apollo flight surgeon reported increasing symptoms upon repeated exposure with associated eosinophilia, indicative of allergy (*Acta Astronautica. 2008 63 (7–10): 980–987). Many ISS crews display a pattern of persistent immune system dysregulation and latent virus reactivation (NPJ Microgravity. 2015 Sep 3; 1:15013; NPJ Microgravity. 2017 Apr 12; 3:11). Some ISS crews manifest atypical respiratory and/or dermatitis symptoms which could have an allergic pathogenesis (J Allergy Clin. Immunol. Pract. 2016 Jul-Aug; 4(4):759-762.e8). It is logical to anticipate crew immune dysregulation would worsen during prolonged deep space missions. Planetary surface hazards will only complicate crew health risks. This study with investigate if LD exposure will elicit an IgE mediated allergic response either to the LD itself or concomitant antigen exposure during spaceflight. Allergic reactivity could adversely increase clinical and operational impacts for long-duration lunar astronauts and affect countermeasure requirements for surface vehicles. Specific aims for this study are to answer two questions: (1) Does in vitro LD exposure result in increased histamine from human peripheral blood basophils? (2) Can LD impact the capacity of CD4+ T helper and/or CD19+ B-cell mediated IgE production? To address these questions, after the proposal and selection by NASA, our laboratory has separately requested and been approved for receipt of actual LD samples from the Apollo 16 mission. These samples will be used during the study to complete the proposed set of in vitro cell culture experiments (short and long term), using human peripheral blood mononuclear cells (PBMC) and basophils from both atopic and non-atopic individuals. Cells will be co-cultured with cellular mitogens, common recall antigens (Der p1), fine ground silica quartz (as a possible allergenic component of LD), or LD, to study whether LD exposure for varying time intervals will alter the generation of selective immune responses associated with clinical allergic reactions. Measured outputs include supernatant-derived IgE, tryptase, histamine, and selected cytokine levels. Cellular activation will be monitored by assessing activation markers via flow cytometry. EM/x-ray analysis will be used to determine cellular interactions with dust particles. A series of validation experiments was initiated in FY22 once the delivery of LD was received. Based on initial experimental findings, we are optimizing the culture conditions, LD concentrations, and refining our other protocol stimuli.

Audrie A. Colorado↗

NASA NTRSDate not supplied

Hazards of Lunar Surface Exploration: Determining the Immunogenicity/Allergenicity of Lunar Dust

Although infrequent, there have been Apollo program reports of lunar dust (LD) exposure leading to notable upper respiratory symptoms in select crewmembers. Possible mechanisms include particulate irritation, oxidization and release of noxious gas, or legitimate adaptive immune-mediated response. Although sterile non-protein matter would not be expected to be an allergen, one Apollo flight surgeon reported increasing symptoms upon repeated exposure with associated eosinophilia, indicative of allergy (*Acta Astronautica. 2008 63 (7–10): 980–987). Many ISS crews display a pattern of persistent immune system dysregulation and latent virus reactivation (NPJ Microgravity. 2015 Sep 3; 1:15013; NPJ Microgravity. 2017 Apr 12; 3:11). Some ISS crews manifest atypical respiratory and/or dermatitis symptoms which could have an allergic pathogenesis (J Allergy Clin. Immunol. Pract. 2016 Jul-Aug; 4(4):759-762.e8). It is logical to anticipate crew immune dysregulation would worsen during prolonged deep space missions. Planetary surface hazards will only complicate crew health risks. This study with investigate if LD exposure will elicit an IgE mediated allergic response either to the LD itself or concomitant antigen exposure during spaceflight. Allergic reactivity could adversely increase clinical and operational impacts for long-duration lunar astronauts and affect countermeasure requirements for surface vehicles. Specific aims for this study are to answer two questions: (1) Does in vitro LD exposure result in increased histamine from human peripheral blood basophils? (2) Can LD impact the capacity of CD4+ T helper and/or CD19+ B-cell mediated IgE production? To address these questions, after the proposal and selection by NASA, our laboratory has separately requested and been approved for receipt of actual LD samples from the Apollo 16 mission. These samples will be used during the study to complete the proposed set of in vitro cell culture experiments (short and long term), using human peripheral blood mononuclear cells (PBMC) and basophils from both atopic and non-atopic individuals. Cells will be co-cultured with cellular mitogens, common recall antigens (Der p1), fine ground silica quartz (as a possible allergenic component of LD), or LD, to study whether LD exposure for varying time intervals will alter the generation of selective immune responses associated with clinical allergic reactions. Measured outputs include supernatant-derived IgE, tryptase, histamine, and selected cytokine levels. Cellular activation will be monitored by assessing activation markers via flow cytometry. EM/x-ray analysis will be used to determine cellular interactions with dust particles. A series of validation experiments was initiated in FY22 once the delivery of LD was received. Based on initial experimental findings, we are optimizing the culture conditions, LD concentrations, and refining our other protocol stimuli.

immunology↗