Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “EQUATIONS OF MOTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Near-wall variable-Prandtl-number turbulence model for compressible flows

A near-wall four-equation turbulence model is developed for the calculation of high-speed compressible turbulent boundary layers. The four equations used are the k-epsilon equations and the theta(exp 2)-epsilon (sub theta) equations. These equations are used to define the turbulent diffusivities for momentum and heat fluxes, thus allowing the assumption of dynamic similarity between momentum and heat transport to be relaxed. The Favre-averaged equations of motion are solved in conjunction with the four transport equations. Calculations are compared with measurements and with another model's predictions where the assumption of the constant turbulent Prandtl number is invoked. Compressible flat plate turbulent boundary layers with both adiabatic and constant temperature wall boundary conditions are considered. Results for the range of low Mach numbers and temperature ratios investigated are essentially the same as those obtained using an identical near-wall k-epsilon model. In general, there are significant improvements in the predictions of mean flow properties at high Mach numbers.

Sommer, T. P.↗
NASA NTRS1993

Non-recursive augmented Lagrangian algorithms for the forward and inverse dynamics of constrained flexible multibodies

A technique is presented for solving the inverse dynamics of flexible planar multibody systems. This technique yields the non-causal joint efforts (inverse dynamics) as well as the internal states (inverse kinematics) that produce a prescribed nominal trajectory of the end effector. A non-recursive global Lagrangian approach is used in formulating the equations for motion as well as in solving the inverse dynamics equations. Contrary to the recursive method previously presented, the proposed method solves the inverse problem in a systematic and direct manner for both open-chain as well as closed-chain configurations. Numerical simulation shows that the proposed procedure provides an excellent tracking of the desired end effector trajectory.

Bayo, Eduardo↗
NASA NTRS1997

Turbulence Modeling Validation, Testing, and Development

The primary objective of this work is to provide accurate numerical solutions for selected flow fields and to compare and evaluate the performance of selected turbulence models with experimental results. Four popular turbulence models have been tested and validated against experimental data often turbulent flows. The models are: (1) the two-equation k-epsilon model of Wilcox, (2) the two-equation k-epsilon model of Launder and Sharma, (3) the two-equation k-omega/k-epsilon SST model of Menter, and (4) the one-equation model of Spalart and Allmaras. The flows investigated are five free shear flows consisting of a mixing layer, a round jet, a plane jet, a plane wake, and a compressible mixing layer; and five boundary layer flows consisting of an incompressible flat plate, a Mach 5 adiabatic flat plate, a separated boundary layer, an axisymmetric shock-wave/boundary layer interaction, and an RAE 2822 transonic airfoil. The experimental data for these flows are well established and have been extensively used in model developments. The results are shown in the following four sections: Part A describes the equations of motion and boundary conditions; Part B describes the model equations, constants, parameters, boundary conditions, and numerical implementation; and Parts C and D describe the experimental data and the performance of the models in the free-shear flows and the boundary layer flows, respectively.

Bardina, J. E.↗
NASA NTRS2002

Preliminary Planar Formation-Flight Dynamics Near Sun-Earth L2 Point

A few space agencies are planning missions to the vicinity of the Sun-Earth L(sub 2) point, some involving a distributed space system of telescope spacecraft, configured in a plane about a hub. An improved understanding is developed of the relative motion of such objects in formation flight. The telescope equations of motion are written relative to the hub, in terms of the hub s distance from L(sub 2), and an analytical solution is developed, useful for performing orbit control analysis. A halo telescope orbit is investigated, with initial conditions selected to avoid resonance excitation. An example case of the resulting solution is presented.

Segerman, Alan M.↗
NASA NTRS1972

Analog analysis of a tracked air-cushion vehicle.

The dynamics of tracked air-cushion vehicles considered for high-speed ground transportation systems are examined using a vehicle model represented by a one-degree-of-freedom system. The respective equations of motion are derived, and the control system is discussed. The equations obtained for the cushion are solved using an analog computer. The computer showed the effect of the control technique on the relative motion between vehicle and guideway.

Leatherwood, J. D.↗
NASA NTRS1973

Dynamic response and stability of a gas-lubricated Rayleigh-step pad

The quasi-static, pressure characteristics of a gas-lubricated thrust bearing with shrouded, Rayleigh-step pads are determined for a time-varying film thickness. The axial response of the thrust bearing to an axial forcing function or an axial rotor disturbance is investigated by treating the gas film as a spring having nonlinear restoring and damping forces. These forces are related to the film thickness by a power relation. The nonlinear equation of motion in the axial mode is solved by the Ritz-Galerkin method as well as the direct, numerical integration. Results of the nonlinear response by both methods are compared with the response based on the linearized equation. Further, the gas-film instability of an infinitely wide Rayleigh step thrust pad is determined by solving the transient Reynolds equation coupled with the equation of the motion of the pad. Results show that the Rayleigh-step geometry is very stable for bearing number A up to 50. The stability threshold is shown to exist only for ultrahigh values of Lambda equal to or greater than 100, where the stability can be achieved by making the mass heavier than the critical mass.

Cheng, C.↗
NASA NTRS1973

A note on relative motion in the general three-body problem.

It is shown that the equations of the general three-body problem take on a very symmetric form when one considers only their relative positions, rather than position vectors relative to some given coordinate system. From these equations one quickly surmises some well known classical properties of the three-body problem, such as the first integrals and the equilateral triangle solutions. Some new Lagrangians with relative coordinates are also obtained. Numerical integration of the new equations of motion is about 10% faster than with barycentric or heliocentric coordinates.

Broucke, R.↗
NASA NTRS1981

Principal stress formulation of continua motion

Principal stress coordinates are formulated for a material without tension, with the equations of motion projected onto a selected coordinate system. The translations are achieved by forming the local basis vector in correspondence with the local stress tensor. The principal stress coordinates are described as orthogonal and curvilinear, and the metric is defined. The kinematics and dynamics of the principal stress coordinates are analyzed, the latter in orthogonal coordinates, and an analytic formulation of the dynamics of a no-tension material is provided. Finally, elastic granular material such as sand, soil, etc., which are more complicated versions of no-tension material, are explored.

Zak, M.↗
NASA NTRS1976

Rocket/launcher structural dynamics

The equations of motion describing the interactions between a rocket and a launcher were derived using Lagrange's Equation. A rocket launching was simulated. The motions of both the rocket and the launcher can be considered in detail. The model contains flexible elements and rigid elements. The rigid elements (masses) were judiciously utilized to simplify the derivation of the equations. The advantages of simultaneous shoe release were illustrated. Also, the loading history of the interstage structure of a boosted configuration was determined. The equations shown in this analysis could be used as a design tool during the modification of old launchers and the design of new launchers.

Ferragut, N. J.↗
NASA NTRSDate not supplied

Progress on Inverse Estimation Technique of Non-Linear Pitch Damping Coefficient Curves Using Free-Flight CFD Generated Trajectories

Characterization of entry vehicle pitch damping coefficient curves is crucial to ensure appropriate re-entry and overall mission success. The pitch damping coefficient (C_(m_q )+C_(m_α ̇ )) is used to encapsulate the oscillatory growth or decay of a body during a trajectory. The inverse estimation technique utilizes an existing Free-Flight CFD (FF-CFD) dataset and wraps a reconstruction algorithm in an optimizer. The reconstruction integrates the planar equations of motion derived by Schoenenberger, Queen [1] using Python’s scipy.integrate.solve_ivp. The optimizer’s objective function is the normalized 𝐿2 residual of the angle of attack peaks between the reconstructed trajectory and the original data produced with FF-CFD. Inclusion of the peak times in this residual calculation allows for simultaneous optimization of the pitch moment coefficient, C_(m_α ). This residual equation is shown below in Eq. 1. The optimizer scipy.optimize.minimize was used with the gradient-based Powell method for the analysis presented, however the differential evolution method was investigated as means of comparison, and was found to produce marginally lower residual values with prohibitively longer run times. Further, the pitch damping curve is found by fitting a cubic interpolation function to a set of (α, (C_(m_q )+C_(m_α ̇ ))) control points, where the α points are held constant and the (C_(m_q )+C_(m_α ̇ )) values are the optimized parameters. The pitch moment curve uses a linear interpolation between the minimum and maximum α in the dataset. FF-CFD generated trajectories using the Dragonfly capsule geometry with the Genesis ballistic range model parameters were simulated and used for this analysis. These FF-CFD trajectories simulate planar motion, as restricted by the reconstructing the equations of motion, of three different cases: 1-DoF (free-to-pitch), 2-DoF (free-to-pitch and heave), and 3-DoF (free-to-pitch, heave, and decelerate). Pitch damping coefficient curves generated using this inverse estimation curve technique with FF-CFD 1-DoF Dragonfly data are found in Fig. 1. Preliminary results reconstructing ballistic range shots using these FF-CFD derived predictions of the pitch damping curve (Fig. 1) are shown in Fig. 2. It should be noted that the ballistic range shot used a Genesis model whereas the FF-CFD data used a Dragonfly geometry, however these geometries are similar.

entry↗
NASA NTRS2007

Slip Validation and Prediction for Mars Exploration Rovers

This paper presents a novel technique to validate and predict the rover slips on Martian surface for NASA's Mars Exploration Rovers. Different from the traditional approach, the proposed method uses the actual velocity profile of the wheels and the digital elevation map (DEM) from the stereo images of the terrain to formulate simplified equations of motion of the rovers. A weighted factor to the wheel-ground speed from the empirical data comprises the velocity equations of the simplified differential-algebraic system of the rover motion. Applying the discretization operator to these equations, the full kinematics state of the rover is then resolved by the configuration kinematics solution in the Robot Sequencing and Visualization Program (RSVP). This method produced accurate simulation of the rover movements compared with these of the earth testing vehicle. Using the telemetry from the onboard Visual Odometry, the simulated rover path also compares well with the actual track of the vehicle. Preliminary results indicated that the proposed computational method is very effective in planning the path of the rovers on the high-slope areas.

Mars Rovers↗
NASA NTRS1986

The development of optimal control laws for orbiting tethered platform systems

A mathematical model of the open and closed loop in-orbit plane dynamics of a space platform-tethered-subsatellite system is developed. The system consists of a rigid platform from which an (assumed massless) tether is deploying (retrieving) a subsatellite from an attachment point which is, in general, offset from the platform's mass center. A Lagrangian formulation yields equations describing platform pitch, subsatellite tether-line swing, and varying tether length motions. These equations are linearized about the nominal station keeping motion. Control can be provided by both modulation of the tether tension level and by a momentum type platform-mounted device; system controllability depends on the presence of both control inputs. Stability criteria are developed in terms of the control law gains, the platform inertia ratio, and tether offset parameter. Control law gains are obtained based on linear quadratic regulator techniques. Typical transient responses of both the state and required control effort are presented.

Bainum, P. M.↗
NASA NTRS2003

Spaceflight Holography Investigation in a Virtual Apparatus

The movement of a particle in a fluid is one of the most fundamental processes in physics and plays an important role in materials science. For example, the physics of crystal growth from a nucleation site in solution can be dominated by movement of the solution over the crystal surface. Gravity usually dominates the equations of motion, but in microgravity other terms can dominate, making the equation much more complex. Until recently, the equations were solved only by numerical methods and/or by neglecting terms. During this study, we discovered an exact solution to the equations, which shows that the usually neglected terms become extremely important in microgravity. We also developed diagnostic recording methods using holography to save all of the particle field data, allowing the experiment to essentially be transferred from space back to earth in what we call the virtual apparatus . We will record holograms of particle distributions in motion in microgravity and bring them back to earth for analysis, allowing the study of the full three-dimensional motion of sets of particles, allowing us to test the new analytical solutions. The experiment will also provide accurate measurements of the quasi-steady acceleration of the space platform and other interesting microgravity and g-jitter effects. This program will produce the flight definition for an experiment in the microgravity environment of space to validate the theoretical model. We will design an experiment with the help of the theoretical model that is optimized for testing the model, measuring g, g-jitter, and other microgravity phenomena.

Source record↗
NASA NTRS1973

Aeroelastic instabilities of hingeless helicopter blades.

In this study the stability boundaries of a hingeless helicopter blade are studied using a system of coupled flap-lag-pitch equations of motion. Divergence and flutter boundaries for the linearized system of equations are presented. Flap-lag, flap-pitch and coupled flap-lag-pitch instabilities in hovering flight are studied. The effect of the torsional degree of freedom on the flap-lag type of instability is investigated. Similarly the effect of lag on the flap pitch type of instability is also considered. Results illustrating these effects, together with the effect of various important blade parameters on blade stability are presented.

Friedmann, P.↗
NASA NTRS1976

The method of Ritz applied to the equation of Hamilton

Without any reference to the theory of differential equations, the initial value problem of the nonlinear, nonconservative double pendulum system is solved by the application of the method of Ritz to the equation of Hamilton. Also shown is an example of the reduction of the traditional eigenvalue problem of linear, homogeneous, differential equations of motion to the solution of a set of nonhomogeneous algebraic equations. No theory of differential equations is used. Solution of the time-space path of the linear oscillator is demonstrated and compared to the exact solution.

Bailey, C. D.↗
NASA NTRS1976

Condensation of water vapor in rarefaction waves. I - Homogeneous nucleation

A detailed theoretical investigation has been made of the condensation of water vapor/carrier gas mixtures in the nonstationary rarefaction wave generated in a shock tube. It is assumed that condensation takes place by homogeneous nucleation. The equations of motion together with the nucleation rate and the droplet growth equations were solved numerically by the method of characteristics and Lax's method of implicit artificial viscosity. It is found that, for the case considered, the condensation wave formed by the collapse of the metastable nonequilibrium state is followed by a shock wave generated by the intersection of characteristics of the same family. The expansion is practically isentropic up to the onset of condensation. The condensation front accelerates in the x,t plane. The results of the computations for a chosen case of water vapor/nitrogen mixture are presented by plotting variations of pressure, nucleation rate, number density of critical clusters, and condensate mass-fraction along three particle paths. Some consideration is given to homogeneous condensation experiments conducted in a shock tube. Although a direct comparison of the present theoretical work and these experiments is not possible, several worthwhile interpretative features have resulted nevertheless.

Sislian, J. P.↗
NASA NTRS1978

Solitary Rossby waves in zonal shear flows and their interactions

Interactions of long-wave solitons propagating in shear flows are described by a coupled pair of Korteweg-de Vries equations. The basic equation of motion for the analysis is the quasi-geostrophic forecast equation, and the interaction of two wave modes is studied. The solution for mode 1-mode 2 interaction of solitary waves in an asymmetric shear flow of a barotropic atmosphere with divergence is constructed. Streamline patterns for certain flows are obtained. An unsteady solitary wave solution for a modified Korteweg-de Vries equation is derived.

Redekopp, L. G.↗