Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Copper”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42

Effect of copper on the recombination activity of extended defects in silicon

The effect of copper atoms introduced by high-temperature diffusion on the recombination properties of dislocations and dislocation trails in p-type single-crystal silicon is studied by the electron-beam-induced current technique. It is shown that, in contrast to dislocations, dislocation trails exhibit an increase in recombination activity after the introduction of copper. Bright contrast appearance in the vicinity of dislocation trails is detected after the diffusion of copper and quenching of the samples. The contrast depends on the defect density in these trails.

36 MATERIALS SCIENCE↗

Interstitial carbon formation in irradiated copper-doped silicon

The influence of a copper impurity on the spectrum of defects induced in p-Si crystals containing a low oxygen concentration by irradiation with electrons with an energy of 5 MeV at room temperature is studied by deep-level transient spectroscopy. It is found that interstitial carbon atoms (C{sub i}) which are the dominant defects in irradiated samples free of copper are unobservable immediately after irradiation, if the concentration of mobile interstitial copper atoms (Cu{sub i}) is higher than the concentration of radiation defects. This phenomenon is attributed to the formation of (Cu{sub i}, C{sub i}) complexes, which do not introduce levels into the lower half of the band gap. It is shown that these complexes dissociate upon annealing at temperatures of 300–340 K and, thus, bring about the appearance of interstitial carbon.

36 MATERIALS SCIENCE↗

Numerical Simulation of Thermodynamic Parameters of High-Porosity Copper

We propose that a modified equation of state be used for calculating the thermodynamically equilibrium TEC2 model for improving the reliability of description of thermodynamic parameters of shock loading of pure materials and heterogeneous mixtures of various porosities. For copper, the parameters of a thermally consistent equation of state have been determined. A reliable description of shock-wave loading of copper has been obtained using a small number of fitting parameters determined from the concordance with experimental data. Thermodynamic parameters have been simulated for copper with various porosities; the compression ratio and the temperature along the shock adiabat have been determined, and the value of heat capacity along the normal isobar has been calculated. The results of calculations are compared with available experimental results obtained by different authors.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

ATS (Advanced Terrestrial Simulator) integrated hydrology and reactive transport model output in Copper Creek, Colorado

This dataset is generated using the ATS (Advanced Terrestrial Simulator) model at Copper Creek, Colorado, the largest catchment in the East River watershed. ATS is an integrated hydrology and reactive transport model to simulate the Concentration-Discharge (C-Q) relationship, and is used to quantify the geochemical export and understand how watersheds respond to climate disturbances. Key hydrogeochemical variables, including discharge, precipitation, evapotranspiration, and geochemical concentrations, were simulated and output at a daily frequency at the Copper Creek outlet. A group of hydrology and geochemical model variables over the spatial domain are output at a bi-monthly frequency. The model used 1-km resolution daily frequency Daymet meteorological forcing, and mineral composition from previous studies. The simulations are performed on NERSC. The datasets include the input files for running the ATS (Advanced Terrestrial Simulator) simulation, including the mesh file, input script and geochemical model files. The output files from the ATS (Advanced Terrestrial Simulator) are the daily time-series discharge and geochemical concentration simulated at the outlet of Copper Creek, and the bi-monthly spatial output over the simulation domain.

54 ENVIRONMENTAL SCIENCES↗

Copper coating specification for the RHIC arcs

Copper coating specifications for the RHIC arcs are given. Various upgrade scenarios are considered and calculations of resistive wall losses in the arcs are used to constrain the necessary quality and surface thickness of a copper coating. We find that 10 {mu}m of high purity copper will suffice.

43 PARTICLE ACCELERATORS↗

Modelling off Hugoniot Loading Using Ramp Compression in Single Crystal Copper

The application of a ramp load to a sample is a method by which the thermodynamic variables of the high pressure state can be controlled. The faster the loading rate, the higher the entropy and higher the temperature. This paper describes moleculer dynamics (MD) simulations with 25 million atoms which investigate ramp loading of single crystal copper. The simulations followed the propagation of a 300ps ramp load to 3Mbar along the [100] direction copper. The simulations were long enough to allow the wave front to steepen into a shock, at which point the simulated copper sample shock melted.

36 MATERIALS SCIENCE↗

Microbial Competition for Copper: Impacts on Carbon and Nitrogen Cycling

Activities from this DOE sponsored project focused on two general questions: (1) how does competition between microbes for copper affect emissions of greenhouse gasses, especially methane and nitrous oxide? and (2) how does a novel copper-binding compound (methanobactin) made by some methane-oxidizing bacteria bind and reduce metals, as well as what are the regulatory elements involved in controlling methanobactin synthesis? From these efforts, we have conclusively shown that microbial competition for copper does indeed exert significant control on microbial community composition, as well as affects how microbes produce and consume nitrous oxide. We have also developed much better insights into the basis for methanobactin activity, as well as how methanotrophs control its production.

54 ENVIRONMENTAL SCIENCES↗

Upstream Extraction of Tellurium from Copper Concentrates

A major barrier to increasing CdTe PV module production is the availability of tellurium (Te), an element necessary to manufacture CdTe PV cells that currently has a very limited supply. Most Te is obtained from ore extracted for copper mining, but the current processing methods only extract 3-4% of the available Te in this ore, with the rest being discarded during other processing steps. This project aims to increase Te supply by developing an innovative extraction method that will recover more Te from the copper ore earlier in the process. This method will also extract toxic elements like antimony and arsenic, making the copper mining process more environmentally friendly.

14 SOLAR ENERGY↗

Vacuum Bellows, Vacuum Piping, Cryogenic Break, and Copper Joint Failure Rate Estimates for ITER Design Use

The ITER international project design teams are working to produce an engineering design in preparation for construction of the International Thermonuclear Experimental Reactor (ITER) tokamak. During the course of this work, questions have arisen in regard to safety barriers and equipment reliability as important facets of system design. The vacuum system designers have asked several questions about the reliability of vacuum bellows and vacuum piping. The vessel design team has asked about the reliability of electrical breaks and copper-copper joints used in cryogenic piping. Research into operating experiences of similar equipment has been performed to determine representative failure rates for these components. The following chapters give the research results and the findings for vacuum system bellows, power plant stainless steel piping (amended to represent vacuum system piping), cryogenic system electrical insulating breaks, and copper joints.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Liquid Copper and Iron Production from Chalcopyrite, in the Absence of Oxygen

Clean energy infrastructure depends on chalcopyrite: the mineral that contains 70% of the world’s copper reserves, as well as a range of precious and critical metals. Smelting is the only commercially viable route to process chalcopyrite, where the oxygen-rich environment dictates the distribution of impurities and numerous upstream and downstream unit operations to manage noxious gases and by-products. However, unique opportunities to address urgent challenges faced by the copper industry arise by excluding oxygen and processing chalcopyrite in the native sulfide regime. Through electrochemical experiments and thermodynamic analysis, gaseous sulfur and electrochemical reduction in a molten sulfide electrolyte are shown to be effective levers to selectively extract the elements in chalcopyrite for the first time. We present a new process flow to supply the increasing demand for copper and byproduct metals using electricity and an inert anode, while decoupling metal production from fugitive gas emissions and oxidized by-products.

36 MATERIALS SCIENCE↗

Neutron yields for reactions induced by 120 GeV protons on thick copper target

We developed an experimental method to measure neutron energy spectrum for 120-GeV protons on a thick copper target at Fermilab Test Beam Facility (FTBF). The spectrum in the energy range from 16 to 1600 MeV was obtained for 60-cm long copper target by time-of-flight technique with an NE213 scintillator and 5.5-m flight path. Energy spectra of neutrons generated from an interaction with beam and materials are important to design shielding structure of high energy accelerators. Until now, the energy spectra for the incident energy up to 3 GeV have been measured by several groups, Ishibashi et al., Amian et al., and Leray et al. In the energy region above 3 GeV, few experimental data are available because of small number of facilities for neutron experiment. On the other hand, concerning simulation codes, theoretical models for particle generation and transportation are switched from intermediate to high energy one around this energy. The spectra calculated by the codes have not been examined using experimental data. In shielding experiments using 120 GeV hadron beam, experimental data shows systematic differences from calculations. Hagiwara et al. have measured leakage neutron spectra behind iron and concrete shield from 120 GeV proton on target at anti-proton target station in Fermilab by using Bonner Spheres with unfolding technique. In CERN, Nakao et al reported experimental results of neutron spectra behind iron and concrete wall from 120 GeV/c proton and pion mixed beam on copper by using NE213 liquid scintillators with unfolding technique. Both of the results reported systematic discrepancies between experimental and calculation results. Therefore, experimental data are highly required to verify neutron production part of calculations. In this study, we developed an experimental method to measure neutron energy spectrum for 120 GeV proton on target. The neutron energy was determined using time-of-flight technique. We used the Fermilab Test Beam Facility (FTBF) in Fermilab that provided 120 GeV proton beam with intensity of 2 x 10{sup 5}/4 sec in every minute. The point of this study was determination of experimental configuration to satisfy enough statistic and energy resolution of neutrons.

43 PARTICLE ACCELERATORS↗

Unraveling the Active Site in Copper-ceria Systems for the Water Gas Shift Reaction: In-situ Characterization of an Inverse Powder CeO2-x/CuO-Cu Catalyst

An inverse powder system composed of CeO{sub 2} nanoparticles dispersed over a CuO-Cu matrix is proposed as a novel catalyst for the water-gas shift reaction. This inverse CeO{sub 2}/CuO-Cu catalyst exhibits a higher activity than standard Cu/CeO{sub 2} catalysts. In situ synchrotron characterization techniques were employed to follow the structural changes of CeO{sub 2}/CuO-Cu under reaction conditions. Time-resolved X-ray diffraction experiments showed the transformation of CuO to metallic Cu via a Cu{sub 2}O intermediate. Short-order structural changes were followed by pair distribution function analysis and corroborated the results obtained by diffraction. Moreover, X-ray absorption spectroscopy also revealed oxidation state changes from Cu{sup 2+} to Cu{sup 0} and the partial reduction of CeOx nanoparticles. The activity data obtained by mass spectrometry revealed that hydrogen production starts once the copper has been fully reduced. The strong interaction of ceria and copper boosted the catalytic performance of the sample. The inverse catalyst was active at low temperatures, stable to several reaction runs and to redox cycles. These characteristics are highly valuable for mobile fuel cell applications. The active phases of the inverse CeO{sub 2}/CuO-Cu catalyst are partially reduced ceria nanoparticles strongly interacting with metallic copper. The nature and structure of the ceria nanoparticles are of critical importance because they are involved in processes related to water dissociation over the catalyst surface.

08 HYDROGEN↗

Wave speeds in single and polycrystalline copper

A novel technique was used to determine shock speeds in polycrystalline and single crystal copper that makes use of the ready availability of multiple velocimetry channels. Making use of a “top hat” design and five points of photonic Doppler velocimetry (PDV), which allows for accurate timing to determine wave arrival times, shock impacts were executed on [100], [110], and [111] single crystal copper, as well as polycrystalline copper at impact velocities ranging from 300 to 600 m/s. The data show that at these low velocities the [111] and [110] single crystal orientations have different shock speeds than the polycrystalline and [100] single crystal, but those differences may be within the apparent accuracy of the experimental technique.

36 MATERIALS SCIENCE↗

Development of Surface Grain Relief on Self-Ion Irradiated Copper

The development of surface grain relief has been observed on self-ion irradiated pure polycrystalline copper. However, the mechanistic origin of this feature has yet to be determined. Two possible mechanisms, anisotropic creep relaxation of void swelling induced stresses and crystallographic orientation-dependent sputtering rate differences, are being investigated as the cause of this evolution. This work focuses on characterizing the surface development and investigating the mechanism of orientation-dependent sputtering. Based on the conditions under which these specimens were irradiated, preferential sputtering is not likely to be the cause of the observed grain relief. Surface grain relief can greatly influence the ability to non-destructively detect irradiation-induced effects in polycrystalline metals. Determining the origin of grain relief development is necessary before this surface feature can be used an indicator of irradiation-induced effects in pure copper and other alloys. The development of surface grain relief has been observed on self-ion irradiated pure polycrystalline copper irradiated to 100 dpa. This surface feature was first noted by measuring samples using transient grating spectroscopy and later confirmed using scanning electron microscopy. Calculations of single-crystal sputtering rates show that the difference in sputtering yields between a randomly-oriented solid and a low-index plane is not sufficient to account for the observed height difference. SEM images appear to show a maximum step-height difference of around 100 nm and differential sputtering can only account for differences on the order of 10 nm at most. This determination indicates that anisotropic creep relaxation may be the mechanistic origin of the observed surface features. If this is the case, which will be confirmed by future work, then TG spectroscopy may be an effective tool for the determination of the onset of certain radiation-damage evolution. For example, if the onset of creep relaxation is strongly correlated to a specific level of void swelling and if the surface features present as a result of creep relaxation can be observed using TG spectroscopy, then accurate determinations of particular levels of void swelling may be made. (authors)

36 MATERIALS SCIENCE↗

Large discrete resistance jump at grain boundary in copper nanowire

Copper is the current interconnect metal of choice in integrated circuits. As interconnect dimensions decrease, the resistivity of copper increases dramatically because of electron scattering from surfaces, impurities, and grain boundaries (GBs), and threatens to stymie continued device scaling. Lacking direct measurements of individual scattering sources, understanding of the relative importance of these scattering mechanisms has largely been relied on semi-empirical modeling. Here we present the first attempt to measure and calculate individual GB resistances in copper nanowires with a one-to-one correspondence to the GB structure. Four-probe scanning tunneling microscope measurements show discrete resistance jumps across high-angle random GBs and negligibly small resistances across coincidence boundaries. The latter is substantiated by first-principles calculations, while the former is consistent with the prediction of an intrinsic high resistance for random boundaries from a free-electron boundary scattering model. Such a big difference between these GBs provides vital information for nanoscale interconnect technology.

36 MATERIALS SCIENCE↗

Copper complexes: cytotoxicity and transport possibilities

A copper complex with N-(5,6-dihydro-4H-1,3-thiazin-2-yl)benzamide was synthesized for the first time and characterized by {sup 1}H NMR spectroscopy, LETDY mass spectrometry, and elemental analysis. A comparative study of the obtained complex and copper 2-aminopyrimidine complex was performed by flow cytometry on normal lymphocytes and Jurkat cells. Complexes with radionuclides {sup 64,67}Cu (with and wihout a carrier) were prepared, and distribution of the labeled complexes in the organs of mice was considered. Packing in carboxymethylcellulose-based microgels was proposed as a transport form for the complexes. The results show a promise of the obtained materials as potential radiopharmaceutical agents.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Homochiral frameworks derived from magnesium, zinc and copper salts of L-tartaric acid

Five metal-organic frameworks derived from L-tartarate (L-tart=C{sub 4}H{sub 4}O{sub 6}) and the divalent metal ions magnesium, zinc or copper have been prepared and structurally characterized. The frameworks were prepared from the reaction of potassium L-tartrate [KC{sub 4}H{sub 5}O{sub 6}] with the appropriate metal salt in water solutions. The magnesium compound [Mg(L-tart)(H{sub 2}O) contains 1.5H{sub 2}O], 1, crystallizes as a two-dimensional 6{sup 3} sheet structure. The addition of the divergent linker molecules 4,4'-bipyridine (bipy) or trans-1,2-bispyridylethylene (bpe) to systems involving Zn{sup 2+} and Cu{sup 2+} results in the formation of the homochiral three-dimensional structures [Zn{sub 2}(L-tart)2(biyp)(H{sub 2}O) contains 5.25H{sub 2}O], 2, [Cu(L-tart)(bipy) contains 2.33H{sub 2}O], 3, and [Cu(L-tart)(bpe) contains 8H{sub 2}O], 5. Removal of solvent water molecules from 3 resulted in [Cu(L-tart)(bipy) contains 0.2H{sub 2}O], 4. Similar experiments on 2 and 5 resulted in breakdown of the frameworks, illustrating the dependence of the stability of these structures on the guest water molecules. This study reports the structures of two new topological types of binodal nets. - Five metal-organic frameworks derived from L-tartarate and the divalent metal ions magnesium, zinc or copper have been prepared and structurally characterized. Significant structural diversity is displayed within this set of complexes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Copper(II) cyanido-bridged bimetallic nitroprusside-based complexes: Syntheses, X-ray structures, magnetic properties, {sup 57}Fe Moessbauer spectroscopy and thermal studies

Three heterobimetallic cyanido-bridged copper(II) nitroprusside-based complexes of the compositions [Cu(tet)Fe(CN){sub 5}NO].H{sub 2}O (1), where tet=N,N'-bis(3-aminopropyl)ethylenediamine, [Cu(hto)Fe(CN){sub 5}NO].2H{sub 2}O (2), where hto=1,3,6,9,11,14-hexaazatricyclo[12.2.1.1{sup 6,9}]octadecane and [Cu(nme){sub 2}Fe(CN){sub 5}NO].H{sub 2}O (3), where nme=N-methylethylenediamine, were synthesized and characterized by elemental analyses, {sup 57}Fe Moessbauer and FTIR spectroscopies, thermal analysis, magnetic measurements and single-crystal X-ray analysis. The products of thermal degradation processes of 2 and 3 were studied by XRD, {sup 57}Fe Moessbauer spectroscopy, SEM and EDS, and they were identified as mixtures of CuFe{sub 2}O{sub 4} and CuO. - Three heterobimetallic cyano-bridged copper(II) nitroprusside-based complexes of the general compositions of [Cu(L)Fe(CN){sub 5}NO].xH{sub 2}O, where L=N,N'-bis(3-aminopropyl)ethylenediamine (complex 1), 1,3,6,9,11,14-hexaazatricyclo[12.2.1.1{sup 6,9}]-octadecane (complex 2) and N-methylethylenediamine (complex 3), were synthesized, and fully structurally and magnetically characterized. SEM, EDS, XRD and {sup 57}Fe Moessbauer experiments were used for characterization of thermal decomposition products of complexes 2 and 3.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗