Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CELLULOSE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42

In Situ Synthesized Hydroxyapatite—Cellulose Nanofibrils as Biosorbents for Heavy Metal Ions Removal

The synthesis of hydroxyapatite (HAp) in the presence of cellulose nanofibrils (CNF) or TEMPO-oxidized CNF (TCNF) was performed in situ by wet chemical precipitation process, using chemical precursors, to hybrid a low-cost biosorbents for removal of Co{sup 2+} as a model heavy metal ion. The removal is investigated by batch adsorption method depending on the pH value, the dosage of adsorbent, initial Co{sup 2+} concentration and the contact time of adsorption. The removal of Co{sup 2+} reached the maximum (87%) at pH 6 by using a dosage of 0.5 g L{sup −1}. The TCNFs is shown to increase the nucleation and growth of the HAp synthesized, providing higher surface area (138 m{sup 2} g{sup −1}) with lower pore diameter (11.89 nm), compared to the CNFs based hybrid (135 m{sup 2} g{sup −1}, 14.42 nm) or pure HAp (118 m{sup 2} g{sup −1}, 13.32 nm), however, both resulting to a higher adsorption capacity (25 mg g{sup −1}) of Co{sup 2+} compared to HAp or TCNF (20–22 mg g{sup −1}). The adsorption is follows primarily by pseudo-first and Elovic order kinetic models which is due to the physisorption of Co{sup 2+} and surface ionic interactions with available negative phosphate (from HAp) and/or carboxylic (from TCNF) groups, fitting well with the Freundlich adsorption isotherm, and secondly due to the ion-exchange mechanism of Co{sup 2+} with Ca{sup 2+} from HAp. Both hybrid adsorbents show good adsorption (≥40%) capacity even after third reusing cycle, and high temperature stability (weight loss of 14%) up to 1000 °C, however, the CNF-HAp hybrid represent a high-value alternative to relatively costly TCNF.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Hempseed cell wall polysaccharides are dominated by linear xylans and cellulose: Comprehensive structural profiling of ten cultivars of industrial hemp, Cannabis sativa L .

Hempseed is a rich source of dietary fiber; however, there has been limited research on the variability of carbohydrate composition in hempseed cell walls. The primary aim of this study was to conduct a comprehensive chemical and structural analysis of the cell wall polysaccharides in ten hempseed cultivars. Water-soluble polysaccharides (WSP) and water-insoluble residues (WIR) were isolated and subsequently analyzed for their monosaccharide composition using HPAEC-PAD, glycosyl linkage analysis using GC–MS, and structural characterization via NMR spectroscopy. All hempseed cultivars contained a high proportion of insoluble fibers and smaller amounts of soluble polysaccharides. Glucose and xylose were the most abundant components of the WIR fractions, while the WSP fractions contained abundant amounts of galactose, galacturonic acid, arabinose, rhamnose, and mannose. The results of linkage and spectroscopic analysis were consistent with the compositional analysis, identifying cellulose and acetylated linear xylans as primary components of WIR, and arabinogalactans, rhamnogalacturonans, heteromannans, xyloglucans, and arabinan as predominant in WSP. Altogether, the study revealed a comparable cell wall structure among the analyzed hemp seed varieties. The high fiber content of whole hempseed-based ingredients presents significant potential for food manufacturers seeking to develop products with enhanced dietary fiber content, offering both functional and nutritional benefits for consumers.

59 BASIC BIOLOGICAL SCIENCES↗

Towards the scale-up production of cellulose nanocomposites using melt processing: A critical review on structure-processing-property relationships

Cellulose nanomaterials (CNMs) naturally exist in plant biomass. The success of extraction of CNMs opened up a new era of using plant biomass for innovative industrial applications. Because CNMs are abundant, renewable, biodegradable, transparent, light weight and low in cost, they are ideal materials for large volume applications such as packaging, automotive, building and infrastructure. In many potential application areas, CNM-enable products appear in a composite form, mostly polymer composites. Additionally, the industrial-scale manufacturing of CNM/thermoplastic composites remains as a set of unsolved problems for academia and industry. A prime challenge in applications is the nanoscale dispersion of CNMs in thermoplastic matrices during melt processing. Both bench-scale and pilot-scale studies have been conducted to solve the dispersion issue of CNMs. In this article, research related to the dispersion of CNMs in thermoplastic matrices during melt processing were critically reviewed. All research papers were classified into three groups: chemically-aided dispersion, physically-aided dispersion and mechanically-aided dispersion. Numerous factors affect the CNM dispersion and the mechanical performance of its nanocomposites. There are material-related factors, including CNM types and forms, polymer matrices, surface modification, coupling agents, etc. Furthermore, extrusion processing parameters also play a significant role, covering screw rotation speed, extrusion barrel temperature settings and screw design. In addition, the material-related factors interact with the processing-related factors. Understanding all factors and their interactions are important for moving CNM nanocomposites research a step further towards industrial-relevant production, which is the final ambitious goal of this manuscript.

42 ENGINEERING↗

Investigation of the alkaline hydrogen peroxide pretreatment: From cellulose saccharification to lignin isolation

Alkaline hydrogen peroxide (AHP) pretreatment, a green and effective technology for biomass fractionation, was studied to overcome the recalcitrance of bamboo for lignin isolation and facilitating enzymatic saccharification. In order to explore the impact of AHP pretreatment on the cellulose saccharification of bamboo, the glucan/xylan recovery, lignin removal, and structural properties of solid substrate were investigated in this research. AHP pretreatment at 90 °C for 60 min with 3.0 % H 2 O 2 resulted in the maximum glucan/xylan hydrolysis yield reaching 90.62 % and 88.30 %, respectively. Specially, for the first time, the recovered lignin from the AHP liquid possesses up to 59.84/100Ar of β-O-4 linkages, abundant ferulic acid (FA), and p-coumarate (pCE) structures, as well as a homogeneous molecular structure with high purity (84.04%-96.20%) and preferable antioxidant activities (IC50: 0.015–0.018 mg/mL). Finally, these results provided theoretical support for the comprehensive valorization of lignocellulose, which is favorable for achieving viable biorefineries.

09 BIOMASS FUELS↗

Heterogeneous Diels–Alder tandem catalysis for converting cellulose and polyethylene into BTX

Producing biomass-derived aromatic hydrocarbons via controllable Diels–Alder reactions is a promising approach to recover energy and chemicals from waste streams. A tandem Diels–Alder catalysis consisting of SAPO-34 and Fe/HZSM-5 (stacked catalysis or mixed catalysis) was evaluated for thermochemical conversion of cellulose and polyethylene blends into benzene, toluene, and xylenes (BTX). Aromatization catalyst type significantly affected the activity of tandem catalysis, and the BTX obtained from the HZSM-5 stacked catalysis was ~2.3 times higher than that of the USY stacked one. An introduction of Fe active promoters into HZSM-5 increased the Lewis to Brønsted acid sites molar ratio (L/B) from 0.4 to 4.1. The comparison between Fe/HZSM-5 stacked catalysis and parent HZSM-5 single catalysis indicated that the former was more effective for BTX production, obtaining a nearly two-fold increase in yield with a high selectivity of 82.8%. A close proximity between Fe/HZSM-5 and SAPO-34 in the mixed catalysis increased the BTX enhancement to 1.8. A synergistic effect was provided by the coordination of Lewis and Brønsted acid sites in the Fe/HZSM-5 mixed catalysts for facilitating BTX generation, achieving a maximum of 25.9% at a Fe/HZSM-5 to SAPO-34 mass ratio of 1:1 with a theoretical L/B of 7.2. Finally, this work provides a sustainable strategy to produce biomass-derived aromatic hydrocarbons.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Evolution of weld metal microstructure in shielded metal arc welding of X70 HSLA steel with cellulosic electrodes: A case study

The microstructure of weld joint in X70 line pipe steel resulted from shielded metal arc welding with E6010 cellulosic electrodes is characterized using optical and electron microscopy. A range of ferritic morphologies have been identified ranging from polygonal inter- and intra-prior austenite grains allotriomorphic, idiomorphic ferrites to Widmanstätten, acicular and bainitic ferrites. Electron Backscatter Diffraction (EBSD) analysis using Image Quality (IQ) and Inverse Pole Figure (IPF) maps through superimposition of IQ and IPF maps and measurement of percentages of high and low angle grain boundaries was identified to assist in differentiation of acicular ferrite from Widmanstätten and bainitic ferrite morphologies. In addition two types of pearlitic structures were identified. There was no martensite detected in this weld structure. The morphology, size and chemistry of non-metallic inclusions are also discussed briefly. - Highlights: • Application of EBSD reveals orientation relationships in a range of phases for shielded metal arc welding of HSLA steel. • Nucleation sites of various ferrite morphologies identified • Formation of upper and lower bainite and their morphologies.

36 MATERIALS SCIENCE↗

Hydroxy propyl cellulose capped silver nanoparticles produced by simple dialysis process

Silver (Ag) nanoparticles ({approx}6 nm) were synthesized using a novel dialysis process. Silver nitrate was used as a starting precursor, ethylene glycol as solvent and hydroxy propyl cellulose (HPC) introduced as a capping agent. Different batches of reaction mixtures were prepared with different concentrations of silver nitrate (AgNO{sub 3}). After the reduction and aging, these solutions were subjected to ultra-violet visible spectroscopy (UVS). Optimized solution, containing 250 mg AgNO{sub 3} revealed strong plasmon resonance peak at {approx}410 nm in the spectrum indicating good colloidal state of Ag nanoparticles in the diluted solution. The optimized solution was subjected to dialysis process to remove any unreacted solvent. UVS of the optimized solution after dialysis showed the plasmon resonance peak shifting to {approx}440 nm indicating the reduction of Ag ions into zero-valent Ag. This solution was dried at 80 {sup o}C and the resultant HPC capped Ag (HPC/Ag) nanoparticles were studied using transmission electron microscopy (TEM) for their particle size and morphology. The particle size distribution (PSD) analysis of these nanoparticles showed skewed distribution plot with particle size ranging from 3 to 18 nm. The nanoparticles were characterized for phase composition using X-ray diffractrometry (XRD) and Fourier transform infrared spectroscopy (FT-IR).

36 MATERIALS SCIENCE↗

Preparation and dielectric properties of SiC nanowires self-sacrificially templated by carbonated bacterial cellulose

Graphical abstract: Display Omitted Highlights: ► A new material – CBC is introduced as a template to prepare SiC nanowires. ► SiC nanowires are synthesized by the infiltration process of reactive vapor Si. ► The highest ε″ of β-SiC nanowires is obtained at 1400 °C. -- Abstract: SiC nanowires were synthesized by the infiltration process of reactive vapor Si in Ar atmosphere at 1350–1450 °C, using carbonated bacterial cellulose (CBC) as carbon template and a reactant. Scanning electron microscopy (SEM), powder X-ray diffraction (XRD), transmission electron microscopy (TEM), high-resolution TEM (HRTEM), and vector network analyzer were employed to characterize the samples. The diameter of the resulting β-SiC nanowires changes with calcination temperatures, specifically, 35–60 nm for 1350 °C, 40–80 nm for 1400 °C, and 30–60 nm for 1450 °C. The β-SiC nanowires obtained at 1400 °C possess the highest ε″ of complex permittivity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Multifunctional polymer composite coatings and adhesives by incorporating cellulose nanomaterials

Regardless of their applications, polymers are still considered mechanically weak and functionally insufficient for certain demanding coating and adhesive uses. To address those issues, nanomaterials have been extensively studied as reinforcing fillers, which have been proven to effectively promote the performance of polymer coatings/adhesives. However, conventional nanofillers are expensive and non-biodegradable. Meanwhile, cellulose nanomaterials (CNMs), a class of nanomaterials produced from biomass feedstocks, can circumvent the drawbacks of conventional nanofillers. Here, this review paper first focuses on the multi-functionalities CNMs bring to polymer coatings, including mechanical reinforcement (wear resistance and hardness enhancement), gas barrier, flame resistance, corrosion resistance, self-healing (controlled-release), optical regulation, self-cleaning/antifouling, and antimicrobial characteristics. Then we discuss the benefits of CNM addition to polymer adhesives, such as mechanical enhancement, curing promotion, volatile organic compound (VOC) suppression, and electrical conductivity. Finally, we provide insights into future research efforts with CNMs. The goal of this paper is to promote the pilot-scale study and commercial use of CNMs as multifunctional additives in green and sustainable polymer composite coating and adhesive formulations.

36 MATERIALS SCIENCE↗

Realistic application of short-lived fission product delayed neutron, gamma-ray analysis for simultaneous nondestructive trace quantification of U, Pu mixtures on cellulose swipes

Detection and characterization of fissile traces are of interest to the international nuclear nonproliferation community, including the International Atomic Energy Agency. Pre-inspection check samples are analyzed by neutron activation analysis at the High Flux Isotope Reactor operated by the Oak Ridge National Laboratory under the umbrella of the IAEA Network of Analytical Laboratories. The simultaneous quantification of U and Pu mixtures was accomplished using the combined delayed neutron (DN) delayed gamma-ray (DG) method to analyze cellulose swipes with actinide loading <1ng in a blind field trial. The total fissile quantity was measured by the DN counts and the relative proportions of U, Pu were determined by calibration of the 104 Tc / 141 Ba fission product count ratio using known mixtures. The DNDG method demonstrated high accuracy in flagging the presence of 239 Pu in uranium down to <100 pg mass loading. In conclusion, peak significance tests helped to control false positive Pu flagging and simultaneous quantification of U and Pu loading was accomplished on samples that passed the significance tests.

36 MATERIALS SCIENCE↗

Compression behavior of microcrystalline cellulose spheres: Single particle compression and confined bulk compression across regimes

Particle characteristics can drastically influence the process-structure-property-performance aspects of granular materials in compression. In this study, we aim to computationally simulate the mechanical processes of stress redistribution in compacts including the kinematics of particle rearrangement during densification and particle deformation leading to fragmentation. Confined compression experiments are conducted with three sets of commercial microcrystalline cellulose particles nearly spherical in shape with different mean particle size. Experimentally measured compression curves from tall powder columns are fitted with the Kenkre et al. (J. of American Chemical Society, Vol. 79, No. 12) model. This model provides a basis to derive several common two-parameter literature models and as a framework to incorporate statistical representations of critical particle behaviors. We focus on the low-stress compression data and the model comparisons typically not discussed in the literature. Furthermore, additional single particle compressions report fracture strength with particle size for comparison to the apparent particle strength extracted from bulk compression data.

42 ENGINEERING↗

Characterization of cellulosic wastes and gasification products from chicken farms

Highlights: Black-Right-Pointing-Pointer The gas chromatography indicated the variable quality of the producer gas. Black-Right-Pointing-Pointer The char had appreciable NPK values, and can be used as a fertiliser. Black-Right-Pointing-Pointer The bio-oil produced was of poor quality, having high moisture content and low pH. Black-Right-Pointing-Pointer Mass and energy balances showed inadequate level energy recovery from the process. Black-Right-Pointing-Pointer Future work includes changing the operating parameters of the gasification unit. - Abstract: The current article focuses on gasification as a primary disposal solution for cellulosic wastes derived from chicken farms, and the possibility to recover energy from this process. Wood shavings and chicken litter were characterized with a view to establishing their thermal parameters, compositional natures and calorific values. The main products obtained from the gasification of chicken litter, namely, producer gas, bio-oil and char, were also analysed in order to establish their potential as energy sources. The experimental protocol included bomb calorimetry, pyrolysis combustion flow calorimetry (PCFC), thermo-gravimetric analyses (TGA), differential scanning calorimetry (DSC), Fourier transform infrared (FT-IR) spectroscopy, Raman spectroscopy, elemental analyses, X-ray diffraction (XRD), mineral content analyses and gas chromatography. The mass and energy balances of the gasification unit were also estimated. The results obtained confirmed that gasification is a viable method of chicken litter disposal. In addition to this, it is also possible to recover some energy from the process. However, energy content in the gas-phase was relatively low. This might be due to the low energy efficiency (19.6%) of the gasification unit, which could be improved by changing the operation parameters.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Characterizing the Range of Extracellular Protein Post-Translational Modifications in a Cellulose-Degrading Bacteria Using a Multiple Proteolyic Digestion/Peptide Fragmentation Approach

Post-translational modifications (PTMs) are known to play a significant role in many biological functions. The focus of this study is to characterize the post-translational modifications of the cellulosome protein complex used by the bacterium Clostridium thermocellum to better understand how this protein machine is tuned for enzymatic cellulose solubilization. To enhance comprehensive characterization, the extracellular cellulosome proteins were analyzed using multiple proteolytic digests (trypsin, Lys-C, Glu-C) and multiple fragmentation techniques (collisionally-activated dissociation, electron transfer dissociation, decision tree). As expected, peptide and protein identifications were increased by utilizing alternate proteases and fragmentation methods, in addition to the increase in protein sequence coverage. The complementarity of these experiments also allowed for a global exploration of PTMs associated with the cellulosome based upon a set of defined PTMs that included methylation, oxidation, acetylation, phosphorylation, and signal peptide cleavage. In these experiments, 85 modified peptides corresponding to 28 cellulosome proteins were identified. Many of these modifications were located in active cellulolytic or structural domains of the cellulosome proteins, suggesting a level of possible regulatory control of protein function in various cellulotyic conditions. The use of multiple enzymes and fragmentation technologies allowed for independent verification of PTMs in different experiments, thus leading to increased confidence in PTM identifications.

Dykstra, Andrew B↗

Review on Nonconventional Fibrillation Methods of Producing Cellulose Nanofibrils and Their Applications

The production of cellulose nanofibrils (CNFs) continues to receive considerable attention because of their desirable material characteristics for a variety of consumer applications. There are, however, challenges that remain in transitioning CNFs from research to widespread adoption in the industrial sectors, including production cost and material performance. Here, we cover CNFs produced from nonconventional fibrillation methods as a potential alternative solution. Pretreating biomass by biological, chemical, mechanical, or physical means can render plant feedstocks more facile for processing and thus lower energy requirements to produce CNFs. CNFs from nonconventional fibrillation methods have been investigated for various applications, including films, composites, aerogels, and Pickering emulsifiers. Continued research is needed to develop protocols to standardize the characterization (e.g., degree of fibrillation) of the lignocellulosic fibrillation processes and resulting CNF products to make them more attractive to the industry for specific product applications.

54 ENVIRONMENTAL SCIENCES↗

Enabling Ambient Stability of LiNiO 2 Lithium-Ion Battery Cathode Materials via Graphene–Cellulose Composite Coatings

Nickel-rich layered oxides are widely used as cathode materials for energy-dense lithium-ion batteries. These chemistries, based on the parent compound LiNiO 2 (LNO), are highly sensitive to ambient environments and are known to readily react with moisture and carbon dioxide. As a result, impurities such as lithium hydroxides and lithium carbonates are formed at the LNO surface, compromising electrochemical behavior. Here, we address this issue by coating LNO cathode particles with a hydrophobic barrier layer composed of graphene and ethyl cellulose (GrEC). This coating limits contact between atmospheric moisture and the LNO surface, which minimizes the generation of lithium impurities. This scheme is evaluated by exposing coated LNO to humidified CO 2 for 24 h as an accelerated ambient degradation test. Subsequent spectroscopy, microscopy, and electrochemical characterization show no detectable signatures of carbonates on the LNO surface, thus verifying that the GrEC coating prevents ambient degradation. In conclusion, by demonstrating this methodology for the ultimate nickel-rich chemistry, this approach can likely be generalized to a wide range of ambient-sensitive battery materials.

25 ENERGY STORAGE↗

Theoretical Insights on the Fragmentation of Cellulosic Oligomers to Form Hydroxyacetone and Hydroxyacetaldehyde

The presence of heavy unknown oligomeric sugar products in bio-oil is evidenced in experimental results reported in the literature. In this paper, we study the fragmentation reactions yielding acetol and glycolaldehyde from oligomeric sugars following previous work on dehydration reactions to propose structures of these oligomers. Acetol and glycolaldehyde are primary products of cellulose fast pyrolysis but the fragmentation reaction mechanism of these compounds from oligomers merits further study. The density functional theory (DFT) approach was employed to study this reaction. Results revealed that acetol and glycolaldehyde fragments are favorably removed from the non-reducing end based on their thermodynamic stabilities. Theoretical FTIR and NMR spectra were calculated to aid in understanding the structures of the oligomeric sugars. Also, the thermodynamics and physical properties of these compounds were estimated using the Group Contribution Method (GCM). In conclusion, these properties are essential in the design of processing technologies and the upgrading of products.

10 SYNTHETIC FUELS↗

Effect of Graft Molecular Weight and Density on the Mechanical Properties of Polystyrene-Grafted Cellulose Nanocrystal Films

In this work, polymer-grafted nanoparticle (PGN) films were prepared from polystyrene (PS) grafted to rodlike cellulose nanocrystals (MxG-CNC-g-PS) with a controllable grafting density (0.03–0.25 chains/nm 2 ) and molecular weight (5–60 kg/mol). These nanorod-based PGNs are solution- and melt-processible, permitting access to one-component composite films with high nanofiller loadings (with up to 55 wt %). The impact of both grafted polymer density and molecular weight on the mechanical properties of the films was investigated and related to the polymer brush conformation: concentrated polymer brush (CPB), semidilute polymer brush (SDPB), or CPB core with SDPB corona (CPB/SDPB). The rubbery regime storage modulus (above $T_g$) showed 2 orders of magnitude increase, maximizing at a low degree of polymerization (N) and low grafting density (σ). Fracture toughness was maximized in samples with the grafted polymer in the SDPB or CPD/SDPB (higher N and relatively low σ) regime and showed enhancement relative to PS of molecular weight similar to the graft. In line with prior computation predictions, optimizing for both rubbery modulus and fracture toughness in such nanorod-based PGN films requires the polymers in the SDPB regime and CNC loading levels (ca. 50–60 wt %) that are difficult to attain in more traditional two-component CNC composites.

36 MATERIALS SCIENCE↗

Understanding the Mechanistic Behavior of Highly Charged Cellulose Nanofibers in Aqueous Systems

Mechanistic behavior and flow properties of cellulose nanofibers (CNFs) in aqueous systems can be described by the crowding factor and the concept of contact points, which are functions of the aspect ratio and concentration of CNF in the suspension. In the study reported herein, CNFs with a range of aspect ratio and surface charge density (380–1360 μmol/g) were used to demonstrate this methodology. It was shown that the critical networking point of the CNF suspension, determined by rheological measurements, was consistent with the gel crowding factor, which was 16. Correlated to the crowding factor, both viscosity and modulus of the systems were found to decrease by increasing the charge density of CNF, which also affected the flocculation behavior. Interestingly, an anomalous rheological behavior was observed near the overlap concentration (0.05 wt %) of CNF, at which the crowding factor was below the gel crowding factor, and the storage modulus (G') decreased dramatically at a given frequency threshold. This behavior is discussed in relation to the breakup of the entangled flocs and network in the suspension. The analysis of the mechanistic behavior of CNF aqueous suspensions by the crowding factor provides useful insight for fabricating high-performance nanocellulose-based materials.

36 MATERIALS SCIENCE↗