Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “AFTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Some recent applications of the suction analogy to vortex-lift estimates

An extension of the suction analogy for the estimation of vortex lift along the side edge of wings is reviewed along with the concept of an augmented vortex lift to account for the effect of the leading-edge vortex passing downstream over an aft part of the model. Applications of these extensions have resulted in an improved estimating capability for a wide range of isolated sharp-edge planforms and also for multiple lifting surfaces. Hence, the suction analogy concept can now have wider applicability at both subsonic and supersonic speeds, especially in the preliminary design cycle.

Lamar, J. E.↗
NASA NTRS1976

Heat-Transfer Characteristics of Partially Film Cooled Plug Nozzle on a J-85 Afterburning Turbojet Engine

Plug nozzle film cooling data were obtained downstream of a slot located at 42 percent of the total plug length on a J-85 engine. Film cooling reduced the aft end wall temperature as much as 150 K, reduced total pressure loss in the upstream convection cooling passages by 50 percent, and reduced estimated compressor bleed flow requirement by 14 percent compared to an all convectively cooled nozzle. Shock waves along the plug surface strongly influenced temperature distributions on both convection and film cooled portions. The effect was most severe at nozzle pressure ratios below 10 where adverse pressure gradients were most severe.

Nosek, S. M.↗
NASA NTRS1976

An analytical study of turbulence responses, including horizontal-tail loads, of a control-configured vehicle with relaxed static stability

A static stability augmentation system (SSAS) with angle-of-attack, pitch-rate, and forward-speed feedback is used to stabilize control-configured rigid vehicles with relaxed static stability. Airplane configurations include a baseline configuration and two representative control-configured vehicle configurations. The first statically unstable configuration has baseline geometry and an aft center of gravity; the second statically unstable configuration has reduced tail length and area and a forward neutral point. Stability, flying-qualities, and maneuverability requirements are imposed on the airplane-SSAS systems. Turbulence responses of the rigid airframe and tail loads are examined in terms of configuration changes for a given control law and in terms of control law changes for a given configuration.

Perry, B., III↗
NASA NTRS1976

An investigation of drag reduction fairings on the space shuttle vehicle 5 configuration (model 74-OTS) in the MSFC 14 inch trisonic wind tunnel (FA14)

An experimental investigation was conducted in the MSFC 14-inch TWT (FA14, TWT 600) to determine the static stability and drag on a 0.004 scale model of the shuttle ascent configuration. The primary objective was to study the possibility of reducing the launch vehicle drag by using Orbiter/ET/SRB fairings, streamlined orbiter fore and aft attach structures, SRB and ET alternative nose configurations, and devices for modifying the flow between the orbiter and ET. The secondary objective was to determine the longitudinal and directional characteristics of the ascent configuration with the most promising of the drag reduction devices installed. Data were obtained for a Mach number range of 0.6 through 4.96 and angles of attack from -5 through 5 degrees at zero degrees side slip angle.

Ramsey, P. E.↗
NASA NTRS1976

Noise suppression by an acoustically treated three-ring inlet on a TF-34 engine

Acoustic performance tests were conducted with a three-ring inlet noise suppressor designed for a TF-34 engine. For all tests the aft noise sources were highly suppressed. The measured inlet suppression was large, reaching levels greater than 30 db at the peak. Comparisons of the data and the performance predictions were in reasonably good agreement. The frequency of peak attenuation was well predicted; the magnitude and spectral shape were reasonably well predicted. Agreement was best when the distribution of sound energy across the inlet was taken into account in the performance predictions. Tests in which the length of treatment was varied showed an orderly progression of attenuation with length; performance predictions for the different lengths also showed an orderly progression with length. At the highest speed of the engine, multiple pure tones were present throughout the spectrum in the source noise signature. These tones were effectively suppressed by the inlet liner, even at low frequencies, although the liner was designed to work best at the blade-passing frequency.

Minner, G. L.↗
NASA NTRS1976

Transonic airfoil design using Cartesian coordinates

A numerical technique for designing transonic airfoils having a prescribed pressure distribution (the inverse problem) is presented. The method employs the basic features of Jameson's iterative solution for the full potential equation, except that inverse boundary conditions and Cartesian coordinates are used. The method is a direct-inverse approach that controls trailing-edge closure. Examples show the application of the method to design aft-cambered and other airfoils specifically for transonic flight.

Carlson, L. A.↗
NASA NTRS1975

Phase 2 program on ground test of refanned JT8D turbofan engines and nacelles for the 727 airplane. Volume 3: Ground tests

The NASA Refan Program included full-scale performance and noise ground tests of both a current production (JT8D-15) and a refanned (JT8D-115) engine. A description of the two ground tests including detailed propulsion, noise, and structural test results is presented. The primary objectives of the total test program were comparison of JT8D-15 and JT8D-115 overall propulsion system performance and noise characteristics and determination of incremental component noise levels. Other objectives of the test program included: (1) determination of acoustic treatment effectiveness; (2) measurement of internal sound pressure levels; (3) measurement of inlet and exhaust hardware performance; (4) determination of center-engine surge margin; and (5) evaluation of certain structural characteristics associated with the 727 refan center-engine inlet duct and JT8D refan engine exhaust system. The JT8D-15 and -115 tests were conducted during September 1974 and January to March 1975, respectively. Analyses of the test data indicated that the JT8D-115, as compared to the JT8D-15, demonstrates a 12.5 percent to 13.2 percent reduction in static specific fuel consumption, and a reduction of 6 to 7 PNdB in a weighted average value of static tone corrected perceived noise level. Separated into noise components, a significant reduction was shown for the inlet fan, aft fan, exhaust duct flow, turbine, and jet noises. However, core noise was increased. Photographs of test stands and test equipment are shown.

Source record↗
NASA NTRS1976

Unsteady aerodynamic flow field analysis of the space shuttle configuration. Part 4: 747/orbiter aeroelastic stability

A quasi-steady analysis of the aeroelastic stability of the lateral (antisymmetric) modes of the 747/orbiter vehicle was accomplished. The interference effect of the orbiter wake on the 747 tail furnishes an aerodynamic undamping contribution to the elastic modes. Likewise, the upstream influence of the 747 tail and aft fuselage on the orbiter beaver-tail rail fairing also is undamping. Fortunately these undamping effects cannot overpower the large damping contribution of the 747 tail and the modes are damped for the configurations analyzed. However, significant interference effects of the orbiter on the 747 tail have been observed in the pitch plane. The high response of the 747 vertical tail in the orbiter wave was also considered. Wind tunnel data points to flapping of the OMS pod wakes as the source of the wake resonance phenomenon.

Reding, J. P.↗
NASA NTRS1975

Analysis of effect of internal and operating variables on performance of SVDS constraint model (ABIND)

An examination of the factors which modify the simulation of a constraint in the motion of the aft attach points of the orbiter and external tank during separation has been made. The factors considered were both internal (spring and damper constants) and external (friction coefficient and dynamic pressure). The results show that an acceptable choice of spring/damper constant combinations exist over the expected range of the external factors and that the choice is consistent with a practical integration interval. The constraint model is shown to produce about a 10 percent increase in the relative body pitch angles over the unconstrained case whereas the MDC-STL constraint model is shown to produce about a 38 percent increase.

Pendergrass, J. R.↗
NASA NTRS1976

Timeline analysis program (TLA-1), appendices

Appendices for the Timeline Analysis Program (TLA-1) were given. The appendices contain the Atlanta terminal area scenarios, the task catalog and the control and display configurations for the forward and aft flight decks of the NASA 515 aircraft, and the event/procedure, phase, mission, and subsystem catalogs.

Miller, K. H.↗
NASA NTRS1976

Validation of scramjet exhaust simulation technique

Scramjet/airframe integration design philosophy for hypersonic aircraft results in configurations having lower aft surfaces that serve as exhaust nozzles. There is a strong coupling between the exhaust plume and the aerodynamics of the vehicle, making accurate simulation of the engine exhaust mandatory. The experimental verification of the simulation procedure is described. The detonation tube simulator was used to produce an exact simulation of the scramjet exhaust for a Mach 8 flight condition. The pressure distributions produced by the exact exhaust flow were then duplicated by a cool mixture Argon and Freon 13B1. Such a substitute gas mixture validated by the detonation tube technique could be used in conventional wind tunnel tests. The results presented show the substitute gas simulation technique to be valid for shockless expansions.

Hopkins, H. B.↗
NASA NTRS1976

Ground simulation and tunnel blockage for a jet-flapped, basic STOL model tested to very high lift coefficients

Ground effects experiments and large/small-tunnel interference studies were carried out on a model with a 20-inch (50.8 cm) span wing. The wing, which includes a highly deflected knee-blown flap can be fitted with unflapped tips and slats. A low-mounted tailplane can be fitted to the aft fuselage. Three-component balance meaurements, made with a fixed ground equipped with a single boundary-layer blowing slot, were compared with datum, moving-ground results. Good comparisons were obtained up to model blowing momentum coefficients of approximately two, after which the particular floor blowing settings used proved insufficient to prevent floor separation in the vicinity of the model. Skin friction measurements, taken routinely along the floor centerline, proved invaluable during the analysis of results, and their use is recommended as input to determination of floor BLC setting. A careful investigation was made of pitching moments, including tail-on, close-to-ground cases, with favorable results. Drag proved the most sensitive to the change from a moving to the boundary-layer controlled ground.

Hackett, J. E.↗
NASA NTRS1976

Single stage, low noise, advanced technology fan. Volume 5: Fan acoustics. Section 1: Results and analysis

The acoustic tests and data analysis for a 0.508-scale fan vehicle of a 111,300 newton (25,000 pound) thrust, full-size engine, which would have application on an advanced transport aircraft, is described. The single-stage advanced technology fan was designed to a pressure ratio of 1.8 at a tip speed of 503 m/sec (1,650 ft/sec) to achieve the desired pressure ratio in a single-stage fan with low radius ratio (0.38), and to maintain adequate stall margin. The fan has 44 tip-shrouded rotor blades and 90 outlet guide vanes. The two basic approaches taken in the acoustic design were: (1) minimization of noise at the source, and (2) suppression of the generated noise in the inlet and bypass exhaust duct. Suppression of the generated noise was accomplished in the inlet through use of the hybrid concept (wall acoustic treatment plus airflow acceleration suppression) and in the exhaust duct with extensive acoustic treatment including a splitter. The goal of the design was attainment of twenty effective perceived noise decibels (20 EPNdB) below current Federal Air Regulation noise standards for a full-scale fan at the takeoff, cutback, and approach conditions. The suppression goal of FAR 36-20 was not reached, but improvements in the technology of both front and aft fan-noise suppression were realized. The suppressed fan noise was shown to be consistent with the proposed federal regulation on aircraft noise.

Jutras, R. R.↗
NASA NTRS1976

Molecular beam mass spectrometer development

An analytical model, based on the kinetics theory of a drifting Maxwellian gas is used to determine the nonequilibrium molecular density distribution within a hemispherical shell open aft with its axis parallel to its velocity. The concept of a molecular shield in terrestrial orbit above 200 km is also analyzed using the kinetic theory of a drifting Maxwellian gas. Data are presented for the components of the gas density within the shield due to the free stream atmosphere, outgassing from the shield and enclosed experiments, and atmospheric gas scattered off a shield orbiter system. A description is given of a FORTRAN program for computating the three dimensional transition flow regime past the space shuttle orbiter that employs the Monte Carlo simulation method to model real flow by some thousands of simulated molecules.

Brock, F. J.↗
NASA NTRS1976

Use of active control technology to improve ride qualities of large transport aircraft

Analyses, construction and flight testing of two systems: Beta-vane and Modal Suppression Augmentation System (MSAS), which were developed to suppress gust induced lateral accelerations of large aircraft, are described. The 747 transport was used as the test vehicle. The purpose of the Beta-vane system is to reduce acceleration levels at the dutch roll frequency whereas the function of the MSAS system is to reduce accelerations due to flexible body motions caused by turbulence. Data from flight test, with both systems engaged shows a 50 to 70 percent reduction in lateral aft body acceleration levels. Furthermore, it is suggested that present day techniques used for developing dynamic equations of motion in the flexible mode region are limited.

Cohen, G. C.↗
NASA NTRS1976

Theoretical analysis of the density within an orbiting molecular shield

An analytical model based on the kinetic theory of a drifting Maxwellian gas is used to determine the nonequilibrium molecular density distribution within a hemispherical shell open aft with its axis parallel to its velocity. Separate numerical results are presented for the primary and secondary density distribution components due to the drifting Maxwellian gas for speed ratios between 2.5 and 10. An analysis is also made of the density component due to gas desorbed from the wall of the hemisphere, and numerical results are presented for the density distribution. It is shown that the adsorption process may be completely ignored. The results are applicable to orbital trajectories in any planet-atmosphere system and interplanetary transfer trajectories. Application to the earth's atmosphere is mentioned briefly.

Hueser, J. E.↗
NASA NTRS1976

Flight effects on JT8D engine jet noise as measured in the NASA Ames 40-by 80-foot wind tunnel

A JT8D-17 turbofan engine was tested in a 40 x 80 ft wind tunnel to determine flight effects on jet noise. The engine was configured as a baseline with conical nozzle, a quiet nacelle 20-lobe ejector/suppressor, and an internal mixer with conical nozzle. Tunnel-off and tunnel-on noise tests were conducted over a range of nozzle pressure ratios (1.2 to 2.1), primary jet velocities (275 to 550 m/s), and tunnel velocities up to 100 m/s. Aft quadrant noise data were measured by a pair of traversing microphones located on a 3-m sideline relative to the engine centerline. Unique correlations and analysis procedures were developed in order to define far-field flight effects from the relatively near-field noise measurements. The ejector/suppressor experienced a significant loss of suppression relative to static measurements during flight while the internal mixer indicated a slight gain in suppression. It is concluded that the wind tunnel is a viable method for studying flight effects on engine jet noise.

Strout, F. G.↗
NASA NTRS1977

Aircraft aerodynamics at high angles of attack

AEROX program estimates aircraft aerodynamics to high angles of attack (up to sixty degrees). It estimates coefficients of lift, induced drag, and pitching moment for wings and wing body combinations with or without aft horizontal tail. Both trimmed and untrimmed characters are calculated.

Axelson, J. A.↗