Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ACTIVATION ENERGY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42

Kinetic study of polymerization/curing of filament-wound composite epoxy resin systems with aromatic diamines

The kinetics of polymerization/curing of a filament-wound composite epoxy resin consisting of an 80/20 DGEBA/DGEBD blend and an MDA/m-PDA blend (Tonox 60/40) was studied at various temperatures and at amine epoxy ratios between 1.1 and 4.4 by means of Fourier-transform (FT) IR and bulk viscosity measurements. The activation energy for the polymerization/curing reaction using an amine/epoxy ratio of 1.1 was 11.9 kcal/mole, in agreement with a previous value. The FT-IR conversion-time plots were fitted to a kinetic expression containing two rate constants with activation energies of 13.7 and 10.0 kcal/mole. The bulk viscosity followed the Williams et al. (1955) equation, with a Di Benedetto (1965) expression for the glass transition temperature.

Golub, M. A.↗

Study of charge transport properties in a ZnO/CdS/Cu(In,Ga)Se 2 solar cell via admittance spectroscopy

The authors investigate the charge carrier transport properties in a thin-film heterojunction Cu(In,Ga)Se 2 (CIGS) solar cell device via coordinated capacitance-voltage and admittance spectroscopic measurements. The CIGS absorber width was measured using temperature dependent depletion width in the freeze-out regime and its acceptor density extracted from conventional capacitance-voltage analysis in the non-freeze-out regime. The bias-dependent modified dielectric relaxation in the Cu(In,Ga)Se 2 solar cell was exploited to extract the absorber's resistivity, hole mobility, and their temperature dependency, all by admittance spectroscopy. In the temperature range of 133-300 K, the extracted hole mobility in the CIGS device increases from 7.55 x 10 -3 to 4.08 cm 2 /Vs with temperature. The temperature dependent resistivity and mobility show Arrhenius behavior with an activation energy ~120 meV. The thermally activated behavior of mobility is related to the potential fluctuation encountered by the holes during their transport, which enables admittance spectroscopy to directly measure the potential fluctuation in the CIGS polycrystalline material.

14 SOLAR ENERGY↗

A 17 O paramagnetic NMR study of Sm 2 O 3 , Eu 2 O 3 , and Sm/Eu-substituted CeO 2

We report that paramagnetic solid-state NMR of lanthanide ( Ln ) containing materials can be challenging due to the high electron spin states possible for the Ln ƒ electrons, which result in large paramagnetic shifts, and these difficulties are compounded for 17 O due to the low natural abundance and quadrupolar character. In this work, we present examples of 17 O NMR experiments for lanthanide oxides and strategies to overcome these difficulties. In particular, we record and assign the 17 O NMR spectra of monoclinic Sm 2 O 3 and Eu 2 O 3 for the first time, as well as performing density functional theory (DFT) calculations to gain further insight into the spectra. The temperature dependence of the Sm 3+ and Eu 3+ magnetic susceptibilities are investigated by measuring the 17 O shift of the cubic sesquioxides over a wide temperature range, which reveal non-Curie temperature dependence due to the presence of low-lying electronic states. This behaviour is reproduced by calculating the electron spin as a function of temperature, yielding shifts which agree well with the experimental values. Using the understanding of the magnetic behaviour gained from the sesquioxides, we then explore the local oxygen environments in 15 at% Sm- and Eu-substituted CeO 2 , with the 17 O NMR spectrum exhibiting signals due to environments with zero, one and two nearest neighbour Ln ions, as well as further splitting due to oxygen vacancies. Finally, we extract an activation energy for oxygen vacancy motion in these systems of 0.35 ± 0.02 eV from the Arrhenius temperature dependence of the 17 O T1 relaxation constants, which is found to be independent of the Ln ion within error. Finally, the relation of this activation energy to literature values for oxygen diffusion in Ln -substituted CeO 2 is discussed to infer mechanistic information which can be applied to further develop these materials as solid-state oxide-ion conductors.

36 MATERIALS SCIENCE↗

Accelerated life testing effects on CMOS microcircuit characteristics

The 250 C, 200C and 125C accelerated tests are described. The wear-out distributions from the 250 and 200 C tests were used to estimate the activation energy between the two test temperatures. The duration of the 125 C test was not sufficient to bring the test devices into the wear-out region. It was estimated that, for the most complex of the three devices types, the activation energy between 200 C and 125 C should be at least as high as that between 250 C and 200 C. The practicality of the use of high temperature for the accelerated life tests from the point of view of durability of equipment is assessed. Guidlines for the development of accelerated life-test conditions are proposed. The use of the silicon nitride overcoat to improve the high temperature accelerated life-test characteristics of CMOS microcircuits is described.

Source record↗

Role of associated defects in oxygen ion conduction and surface exchange reaction for epitaxial samaria-doped ceria thin films as catalytic coatings

Samaria-doped ceria (SDC) thin films are particularly important for energy and electronic applications such as micro-solid oxide fuel cells, electrolysers, sensors and memristors. In this paper we report a comparative study investigating ionic conductivity and surface reactions for well-grown epitaxial SDC films varying the samaria doping concentration. With increasing doping above 20 mol% of samaria, an enhancement in the defect association was observed by Raman spectroscopy. The role of such defect associates on the films` oxygen ion transport and exchange was investigated by electrochemical impedance spectroscopy and electrochemical strain microscopy (ESM). The measurements reveal that the ionic transport has a sharp maximum in ionic conductivity and drop in its activation energy down to 0.6 eV for 20 mol% doping. Increasing the doping concentration further up to 40 mol%, raises the activation energy substantially by a factor of two. We ascribe the sluggish transport kinetics to the "bulk" ionic-near ordering in case of the heavily doped epitaxial films. Analysis of the ESM first order reversal curve measurements indicate that these associated defects may have a beneficial role by lowering the activation of the oxygen exchange "surface" reaction for heavily doped 40 mol% of samaria. We reveal in a model experiment through a solid solution series of samaria doped ceria epitaxial films that the occurrence of associate defects in the bulk affects the surface charging state of the films to increase the exchange rates. Lastly, the implication of these findings are the design of coatings with tuned oxygen surface exchange by control of bulk associate clusters for future electro-catalytic applications.

36 MATERIALS SCIENCE↗

A comprehensive diffusion mobility database comprising 23 elements for magnesium alloys

We report that reliable experimental diffusion coefficients of 10 key alloying elements in Mg obtained by the present authors together with experimental data in the literature enabled us to perform a systematic test of the reliability of diffusion coefficients obtained from DFT calculations. The computed activation energy values were found to be quite accurate (mostly within 0.2 eV) but the computed pre-factors were less reliable. Such insights allowed us to develop a practical and yet robust strategy to perform diffusion mobility assessments by adopting the computed activation energy while fitting only the pre-factor when available experimental data are limited to a narrow temperature range. The overall good agreement between the DFT data and experimental data also gave us the confidence to employ the computed data for those that were still missing or inaccessible from experimental measurements. A systematic assessment of both the measured and computed diffusion data in hcp Mg was performed using the above holistic approach to yield the most comprehensive open Mg mobility database to date, comprising 23 elements (Mg, Ag, Al, Be, Ca, Cd, Ce, Cu, Fe, Ga, Gd, In, La, Li, Mn, Nd, Ni, Pu, Sb, Sn, U, Y, Zn). This more reliable mobility database will contribute to future development of advanced Mg alloys. The holistic approach developed in this study will be very beneficial to the future establishment of reliable mobility databases for other alloy systems as well.

36 MATERIALS SCIENCE↗

Effects of Measurement Materials and Oxygen Partial Pressure on the Viscosity of synthetic Eastern and Western United States Coal Slags

The viscosity of the molten ash (slag) resulting from the mineral constituents in carbon feedstock used in slagging gasifiers is critical for controlling the gasification process. The viscosity of two synthetic slags with compositions resembling the mineral impurities in average eastern and western coal feedstock was examined at temperatures from 1300–1500 °C using a rotating bob viscometer. A few combinations of atmospheres and experimental materials were investigated with respect to one another to determine slag viscosity. A CO/CO{sub 2} atmosphere (CO/CO{sub 2} = 1.8, corresponding to a P{sub O{sub 2}} = 10–8 atm) is required to sustain ferrous ions in FeO-containing slags, an environment that is oxidizing to most metals. Iron oxide in the slag prevents usage of Fe parts. In unpurified Ar, the Fe metal surface oxidizes. Using purified argon prevents iron measurement components from oxidation; however, the metallic surfaces act as nucleation sites for the reduction of the Fe oxide in the slag into metallic Fe. Dissolution of ceramic materials into the slag, including Al{sub 2}O{sub 3} and ZrO{sub 2}, occurs in both atmospheres. Therefore, evaluating slag properties in the laboratory is challenging. The measured viscosities of two synthetic slags in this study diverged depending upon material selection. This difference is likely attributable to container/spindle-slag interactions. Viscosity measurements of the eastern coal slag using all ceramic parts agreed best with FactSage prediction above 1350 °C, with an average activation energy of 271.2 kJ. For western coal slag, the dissolution of container/spindle materials was substantial during the measurement, with precipitation of crystalline phase noted. The experimental viscosity data of the western coal slag agreed best with Kalmanovitch prediction above 1350 °C. The activation energy changed dramatically for both data sets of western coal slag, likely indicating the Newtonian-to-non-Newtonian transition.

01 COAL, LIGNITE, AND PEAT↗

Structure and Site Evolution of Framework Ni Species in MIL-127 MOFs for Propylene Oligomerization Catalysis

A mixed-valence oxotrimer metal–organic framework (MOF), Ni-MIL-127, with a fully coordinated nickel atom and two iron atoms in the inorganic node, generates a missing linker defect upon thermal treatment in helium (>473 K) to engender an open coordination site on nickel which catalyzes propylene oligomerization devoid of any cocatalysts or initiators. This catalyst is stable for ~20 h on stream at 500 kPa and 473 K, unprecedented for this chemistry. The number of missing linkers on synthesized and activated Ni-MIL-127 MOFs is quantified using temperature-programmed oxidation, 1 H nuclear magnetic resonance spectroscopy, and X-ray absorption spectroscopy to be ~0.7 missing linkers per nickel; thus, a majority of Ni species in the MOF framework catalyze propylene oligomerization. In situ NO titrations under reaction conditions enumerate ~62% of the nickel atoms as catalytically relevant to validate the defect density upon thermal treatment. Propylene oligomerization rates on Ni-MIL-127 measured at steady state have activation energies of 55–67 kJ mol –1 from 448 to 493 K and are first-order in propylene pressures from 5 to 550 kPa. Density functional theory calculations on cluster models of Ni-MIL-127 are employed to validate the plausibility of the missing linker defect and the Cossee–Arlman mechanism for propylene oligomerization through comparisons between apparent activation energies from steady-state kinetics and computation. Here this study illustrates how MOF precatalysts engender defective Ni species which exhibit reactivity and stability characteristics that are distinct and can be engineered to improve catalytic activity for olefin oligomerization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Sorption and Transport of Vapors in ZIF-11: Adsorption, Diffusion, and Linker Flexibility

The adsorption and diffusion of alcohol and hydrocarbon vapors in zeolitic imidazolate frameworks (ZIF)-11 are reported as a function of loading at 308 K. The hydrophobicity of the benzimidazole linkers provides moderate ideal adsorbed solution theory selectivities for adsorptive alcohol/water separations until high relative humidity conditions. Sorbates well beyond the crystallographic pore aperture are admitted into the framework at decreasing diffusivities with increasing molecular size. The diffusion of methane is also observed as a function of temperature, revealing a nonconstant activation energy of diffusion, which is linked to the temperature-dependent flexibility of the ligands comprising the six- and eight-membered aperture rings, as revealed through solid-state NMR. Compared to ZIF-8, ZIF-11 surprisingly demonstrates higher diffusivities and lower activation energies despite the smaller crystallographic aperture size. This phenomenon is explained via molecular dynamics simulations that highlight the greater flexibility of the benzimidazole linker in ZIF-11 relative to the 2-methylimidazolate linker in ZIF-8 and specifies the importance of structural flexibility in identifying diffusionally-selective materials.

36 MATERIALS SCIENCE↗

Quantifying Large Lattice Relaxations in Photovoltaic Devices

Temporal variations of Cu(In,Ga)Se 2 photovoltaic device properties during light exposure at various temperatures and voltage biases for times up to 100 h are analyzed using the kinetic theory of large lattice relaxations. Open-circuit voltage and p-type doping increased with charge injection and decreased with temperature at low injection conditions. Furthermore, lattice relaxation can account for both trends and activation energies extracted from the data are approximately 0.9 and 1.2 eV for devices with lower and higher sodium content, respectively. In these devices, increased sodium content resulted in higher initial p-type doping with greater stability. First-principles calculations providing revised activation energies for the (V Se -V Cu ) complex suggest that this defect does not account for the metastability observed here.

14 SOLAR ENERGY↗

Determining the Parameters of the Jahn–Teller Effect in Impurity Centers from Ultrasonic Experiments: Application to the ZnSe : Ni{sup 2+} Crystal

The earlier developed methodology of ultrasonic investigation for determining the parameters of the Jahn–Teller effect (JTE) in impurity centers in crystals is further developed in application to Ni{sup 2+} impurities in ZnSe : Ni{sup 2+}. For all normal modes propagating along the [110] axis, the temperature dependences of the attenuation of ultrasound are measured in the frequency range 25–165 MHz. At a temperature of about 13 K, for all these modes, attenuation peaks are observed, which indicate the presence of local distortions of both trigonal and tetragonal types. Following the previously developed method, it is shown that these anomalies of attenuation are caused by the relaxation transitions between equivalent local distortions induced by the JTE at the Ni{sup 2+} centers. In the tetrahedral environment of selenium, this ion is in the threefold degenerate ground electron state {sup 3}T{sub 1}, in which three types of the JTE can be realized. The data of ultrasonic experiments indicate the realization of the T ⊗ (e + t{sub 2}) problem, in which the potential energy surface has four equivalent minima of the trigonal type, slightly deformed toward tetragonal saddle points. The trigonal vibronic constants, the stabilization energies of the trigonal minima, and the activation energy of the barriers between them are ev-aluated.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Quantitative nanoscale tracking of oxygen vacancy diffusion inside single ceria grains by in situ transmission electron microscopy

Oxygen vacancy formation and migration in ceria is critical to its electrochemical and catalytic properties in systems for chemical and energy transformation, but its quantification is rather challenging especially at atomic-scale because of disordered distribution. Here we report a rational approach to track oxygen vacancy diffusion in single grains of pure and Sm-doped ceria at -20 °C to 160 °C using in situ (scanning) transmission electron microscopy ((S)TEM). To create a gradient in oxygen vacancy concentration, a small region (~30 nm in diameter) inside a ceria grain is reduced to the C-type CeO 1.68 phase by the ionization or radiolysis effect of a high-energy electron beam. The evolution in oxygen vacancy concentration is then mapped through lattice expansion measurement using scanning nano-beam diffraction or 4D STEM at a spatial resolution better than 2 nm; this allows direct determination of local oxygen vacancy diffusion coefficients in a very small domain inside pure and Sm-doped ceria at different temperatures. Further, the activation energies for oxygen transport are determined to be 0.59, 0.66, 1.12, and 1.27 eV for pure CeO 2 , Ce 0.94 Sm 0.06 O 1.97 , Ce 0.89 Sm 0.11 O 1.945 , and Ce 0.8 Sm 0.2 O 1.9 , respectively, implying that activation energy increases due to impurity scattering. The results are qualitatively supported by density functional theory (DFT) calculations. In addition, our in situ TEM investigation reveals that dislocations impede oxygen vacancy diffusion by absorbing oxygen vacancies from the surrounding areas and pinning them locally. With more oxygen vacancies absorbed, dislocations show extended strain fields with local tensile zone sandwiched between the compressed ones. Therefore, dislocation density should be reduced in order to minimize the resistance to oxygen vacancy diffusion at low temperatures.

36 MATERIALS SCIENCE↗

Hot deformation behavior and flow stress modeling of a Ni-based superalloy

The deformation behavior of a novel Ni-based superalloy was investigated using isothermal compression on a Gleeble system at temperatures between 1050 and 1210 °C with strain rates between 0.001 and 0.1 s –1 . Flow-stress curves and electron backscatter diffraction maps were employed to experimentally identify the various flow mechanisms operative during deformation. Deformation at temperatures below 1130 °C presented strong work hardening with limited restoration during dynamic softening leading to partially recrystallized microstructures. Increasing the deformation temperature to and above 1130°C enhanced the driving force for dislocation and grain boundary mobility thereby enabling dynamic recovery (DRV) and dynamic recrystallization (DRX) mechanisms to better operate. Here, the influence of the strain rate was more evident during deformation at these temperatures. Increasing the strain rate from 0.001 s –1 to 0.1 s –1 resulted in a transition in dominant softening mechanism from DRV to DRX. Flow stress modeling using the Zener-Hollomon parameter was performed to obtain the activation energy and the constitutive equation for hot deformation of the alloy. Strong changes in flow behavior affected the accuracy of the flow stress model, and thus, the model was used alternatively to identify deformation parameters associated with various flow regimes. In doing so, the activation energy and the other equation constants were obtained for each deformation mechanism observed experimentally.

36 MATERIALS SCIENCE↗

Bulk and surface controlled diffusion of fission gas atoms

Fission gas retention and release impact nuclear fuel performance by, e.g., causing fuel swelling leading to mechanical interaction with the clad, increasing the plenum pressure and reducing the gap thermal conductivity. All of these processes are important to understand in order to optimize operating conditions of nuclear reactors and to simulate accident scenarios. Most fission gases have low solubility in the fuel matrix, which is especially pronounced for large fission gas atoms such as Xe and Kr, and as a result there is a significant driving force for segregation of gas atoms to extended defects such as grain boundaries or dislocations and subsequently for nucleation of gas bubbles at these sinks. Several empirical or semi-empirical models have been developed for fission gas release in nuclear fuels, e.g. . One of the most commonly used models in fuel performance codes was published by Massih and Forsberg. This model is similar to the early Booth model in that it applies an equivalent sphere to separate bulk UO 2 from grain boundaries represented by the sphere circumference. Compared to the Booth model, it also captures trapping at grain boundaries, fission gas resolution and it describes release from the boundary by applying timedependent boundary conditions to the circumference. In this work we focus on the step where fission gas atoms diffuse from the grain interior to the grain boundaries. The original Massih-Forsberg model describes this process by applying an effective diffusivity divided into three temperature regimes. In this report we present results from density functional theory calculations (DFT) that are relevant for the high (D 3 ) and intermediate (D 2 ) temperature diffusivities of fission gases. The results are validated by making a quantitative comparison to Turnbull's and Matzke's data. For the intrinsic or high temperature regime we report activation energies for both Xe and Kr diffusion in UO 2±x , which compare favorably to available experiments. This is an extension of previous work. In particular, it applies improved chemistry models for the UO 2±x nonstoichiometry and its impact on the fission gas activation energies. The derivation of these models follows the approach that used in our recent study of uranium vacancy diffusion in UO 2 . Also, based on the calculated DFT data we analyze vacancy enhanced diffusion mechanisms in the intermediate temperature regime. In addition to vacancy enhanced diffusion we investigate species transport on the (111) UO 2 surface. This is motivated by the formation of small voids partially filled with fission gas atoms (bubbles) in UO 2 under irradiation, for which surface diffusion could be the rate-limiting transport step. Diffusion of such bubbles constitutes an alternative mechanism for mass transport in these materials.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Kinetic analyses for solid-state phase transition of metastable amorphous-AlO x (2.5 < x ≤ 3.0) nanostructures into crystalline alumina polymorphs

Solid-solid phase change materials (SS-PCMs) hold promise for energy storage/dissipation in batteries and energetic materials. Yet, phase change kinetics for SS-PCMs undergoing metastable to semi-stable/stable phase transformations remain relatively ill-studied because trapping metastable phases remain challenging. Recently, we demonstrated the kinetic entrapment and stabilization of a highly disordered and amorphous Al-oxide phase m-AlO x @C (x~2.5-3.0) via laser ablation synthesis in solution (LASiS). We report here, to our knowledge, the first chemical kinetics analysis for S-S phase transition of the m-AlO 3 @C nanocomposites (< 5–8 nm sizes) into semi-stable equilibrium alumina phases (θ/γ-Al 2 O 3 ) via disproportionation reaction, while releasing excess trapped gases. Our results indicate the atomic density of the AlO 3 structures to be ~5–10 times less than that of the final Al 2 O 3 phases, which led to the hypothesis of a volume shrinkage process during their phase transition. Temperature-dependent X-ray diffraction studies reveal the high-temperature phase transition for m-AlO 3 → θ/γ-Al 2 O 3 to follow contracting volume kinetics model, thereby validating our earlier hypothesis. Using the geometric volume contraction model, reaction kinetics analyses from Arrhenius plots reveal the activation energy barrier for the phase transition to be ~270±11 kJ/mol. This makes the activation energy barrier nearly identical to the oxidation of micron-sized Al particles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

H 2 Desorption from MgH 2 Surfaces with Steps and Catalyst-Dopants

Light-metal hydrides, like MgH 2 , remain under scrutiny as prototypes for reversible H-storage materials. For MgH 2 , we assess hydrogen desorption/adsorption properties (enthalpy and kinetic barriers) for stepped, catalyst-doped surfaces occurring, e.g., from ball-milling in real samples. Employing density functional theory and simulated annealing in a slab model, we studied initial H 2 desorption from stepped surfaces with(out) titanium (Ti) catalytic dopant. Extensive simulated annealing studies were performed to find the dopant’s site preferences. For the most stable initial and final (possibly magnetic) states, nudged elastic band (NEB) calculations were performed to determine the H 2 -desorption activation energy. We used a moment-transition NEB method to account for the dopant’s transition to the lowest-energy magnetic state at each image along the band. We identify a dopant-related surface-desorption mechanism that reloads via bulk H diffusion. While reproducing the observed bulk enthalpy of desorption, we find a decrease of 0.24 eV (a 14% reduction) in the activation energy on doped stepped surface; together with a 22% reduction on a doped flat surface, this brackets the assessed 18% reduction in kinetic barrier for ball-milled MgH 2 samples with low concentration of Ti from experiment.

36 MATERIALS SCIENCE↗

Low temperature aging in a molecular glass: the case of cis -methyl formate

Glassy films of cis-methyl formate show spontaneous dipole orientation on deposition from the vacuum, the so-called ‘spontelectric effect’, creating surface potentials and electric fields within the films. We follow the decay of these fields, and their accompanying dipole orientation, on the hours timescale at deposition temperatures between 40 K and 55 K. Our data trace the low temperature ‘secondary decay’ mechanism, at tens of degrees below the glass transition temperature of 90 K. We show that secondary decay is due to molecular rotation, with associated activation energies lying between 0.1 and 0.2 eV. Diffusion is absent, as established from published neutron reflectivity data. Using an analytical model for the spontelectric effect, data are placed on a quantitative footing, showing that angular motion in excess of 50° reproduces the observed values of activation energies. Exploitation of the spontelectric effect is new in the study of glass aging and is shown here to give insight into the elusive processes which take place far from the molecular glass transition temperature.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Chemical and Thermal Analysis

Thermal decomposition activation energies have been determined using two methods of Thermogravimetric Analysis (TGA), with good correlation being obtained between the two techniques. Initial heating curves indicated a two-component system for Coflon (i.e. polymer plus placticizer) but a single component system for Tefzel. Two widely differing activation energies were for Coflon supported this view, 15 kcl/mol being associated with plasticizer, and 40 kcal/mol with polymer degradation. With Tefzel, values were 40-45 kcal/mol, the former perhaps being associated with a low molecular weight fraction. Appropriate acceleration factors have been determined. Thermomechanical Analysis (TMA) has shown considerable dimensional change during temperature cycles. For unaged pipe sections heating to 100 C and then holding the temperature resulted in a stable thickness increase of 2%, whereas the Coflon thickness decreased continuously, reaching -4% in 2.7 weeks. Previously strained tensile bars of Tefzel expanded on cooling during TMA. SEM performed on H2S-aged Coflon samples showed significant changes in both physical and chemical nature. The first may have resulted from explosive decompression after part of the aging process. Chemically extensive dehydrofluorination was indicated, and sulfur was present as a result of the aging. These observations indicate that chemical attack of PVDF can occur in some circumstances.

Bulluck, J. W.↗