SEARCH · Engineering Papers

Results for “thermal dynamics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

All sources NASA NTRS DOE OSTI

NASA NTRS2014

Dissertation Defense Computational Fluid Dynamics Uncertainty Analysis for Payload Fairing Spacecraft Environmental Control Systems

Spacecraft thermal protection systems are at risk of being damaged due to airflow produced from Environmental Control Systems. There are inherent uncertainties and errors associated with using Computational Fluid Dynamics to predict the airflow field around a spacecraft from the Environmental Control System. This paper describes an approach to quantify the uncertainty in using Computational Fluid Dynamics to predict airflow speeds around an encapsulated spacecraft without the use of test data. Quantifying the uncertainty in analytical predictions is imperative to the success of any simulation-based product. The method could provide an alternative to traditional "validation by test only" mentality. This method could be extended to other disciplines and has potential to provide uncertainty for any numerical simulation, thus lowering the cost of performing these verifications while increasing the confidence in those predictions. Spacecraft requirements can include a maximum airflow speed to protect delicate instruments during ground processing. Computational Fluid Dynamics can be used to verify these requirements; however, the model must be validated by test data. This research includes the following three objectives and methods. Objective one is develop, model, and perform a Computational Fluid Dynamics analysis of three (3) generic, non-proprietary, environmental control systems and spacecraft configurations. Several commercially available and open source solvers have the capability to model the turbulent, highly three-dimensional, incompressible flow regime. The proposed method uses FLUENT, STARCCM+, and OPENFOAM. Objective two is to perform an uncertainty analysis of the Computational Fluid Dynamics model using the methodology found in "Comprehensive Approach to Verification and Validation of Computational Fluid Dynamics Simulations". This method requires three separate grids and solutions, which quantify the error bars around Computational Fluid Dynamics predictions. The method accounts for all uncertainty terms from both numerical and input variables. Objective three is to compile a table of uncertainty parameters that could be used to estimate the error in a Computational Fluid Dynamics model of the Environmental Control System /spacecraft system. Previous studies have looked at the uncertainty in a Computational Fluid Dynamics model for a single output variable at a single point, for example the re-attachment length of a backward facing step. For the flow regime being analyzed (turbulent, three-dimensional, incompressible), the error at a single point can propagate into the solution both via flow physics and numerical methods. Calculating the uncertainty in using Computational Fluid Dynamics to accurately predict airflow speeds around encapsulated spacecraft in is imperative to the success of future missions.

CFD↗

NASA NTRS2014

Dissertation Defense: Computational Fluid Dynamics Uncertainty Analysis for Payload Fairing Spacecraft Environmental Control Systems

Spacecraft thermal protection systems are at risk of being damaged due to airflow produced from Environmental Control Systems. There are inherent uncertainties and errors associated with using Computational Fluid Dynamics to predict the airflow field around a spacecraft from the Environmental Control System. This paper describes an approach to quantify the uncertainty in using Computational Fluid Dynamics to predict airflow speeds around an encapsulated spacecraft without the use of test data. Quantifying the uncertainty in analytical predictions is imperative to the success of any simulation-based product. The method could provide an alternative to traditional validation by test only mentality. This method could be extended to other disciplines and has potential to provide uncertainty for any numerical simulation, thus lowering the cost of performing these verifications while increasing the confidence in those predictions.Spacecraft requirements can include a maximum airflow speed to protect delicate instruments during ground processing. Computational Fluid Dynamics can be used to verify these requirements; however, the model must be validated by test data. This research includes the following three objectives and methods. Objective one is develop, model, and perform a Computational Fluid Dynamics analysis of three (3) generic, non-proprietary, environmental control systems and spacecraft configurations. Several commercially available and open source solvers have the capability to model the turbulent, highly three-dimensional, incompressible flow regime. The proposed method uses FLUENT, STARCCM+, and OPENFOAM. Objective two is to perform an uncertainty analysis of the Computational Fluid Dynamics model using the methodology found in Comprehensive Approach to Verification and Validation of Computational Fluid Dynamics Simulations. This method requires three separate grids and solutions, which quantify the error bars around Computational Fluid Dynamics predictions. The method accounts for all uncertainty terms from both numerical and input variables. Objective three is to compile a table of uncertainty parameters that could be used to estimate the error in a Computational Fluid Dynamics model of the Environmental Control System spacecraft system.Previous studies have looked at the uncertainty in a Computational Fluid Dynamics model for a single output variable at a single point, for example the re-attachment length of a backward facing step. For the flow regime being analyzed (turbulent, three-dimensional, incompressible), the error at a single point can propagate into the solution both via flow physics and numerical methods. Calculating the uncertainty in using Computational Fluid Dynamics to accurately predict airflow speeds around encapsulated spacecraft in is imperative to the success of future missions.

Fluid Dynamics↗

NASA NTRS2020

Electrical Modeling and Thermal Analysis Toolbox (EMTAT) User’s Guide

A simulation toolbox has been developed to model the electrical portions of Electrified Aircraft Propulsion (EAP) systems, including self-heating of electrical systems. Dynamic models of EAP systems often include turbomachinery, an electrical power system, and a thermal management system. These portions of the propulsion system can operate on timescales covering six orders of magnitude, which poses a challenging modeling task. Assumptions and approximations are made in an effort to capture the dynamics relevant to engine, electrical system, and thermal system interactions, while still allowing for fast simulations. These assumptions and approximations enable the electrical component models to run at the time scale of the turbomachinery, neglecting the very high frequency electrical dynamics, while demonstrating representative behavior of the end-to-end system. Thus the models execute in an acceptable time frame for what would otherwise be an extremely stiff simulation. The resulting simulations of EAP systems are appropriate for system-level control design and analysis. The objective of this User's Guide is to present an overview of the usage of the Electrical Modeling and Thermal Analysis Toolbox (EMTAT). It will describe some of the approximations made to accommodate rapid execution, and some of the design tools that allow matching the model to component specifications. This paper will describe the basic usage of the software toolbox, and also provide an example of EAP system modeling using EMTAT.

Mark E. Bell↗

NASA NTRS2011

Lattice Thermal Conductivity of Ultra High Temperature Ceramics (UHTC) ZrB2 and HfB2 from Atomistic Simulations

Ultra high temperature ceramics (UHTC) including ZrB2 and HfB2 are candidate materials for applications in extreme environments because of their high melting point, good mechanical properties and reasonable oxidation resistance. Unlike many ceramics, these materials have high thermal conductivity which can be advantageous, for example, to reduce thermal shock. Recently, we developed Tersoff style interatomic potentials for both ZrB2 and HfB2 appropriate for atomistic simulations. As an application, Green-Kubo molecular dynamics simulations were performed to evaluate the lattice thermal conductivity for single crystals of ZrB2 and HfB2. The atomic mass difference in these binary compounds leads to oscillations in the time correlation function of the heat current. Results at room temperature and at elevated temperatures will be reported.

Lawson, JOhn W.↗

NASA NTRS1989

Particle dynamics and gamma-ray emission in the magnetospheres of neutron stars with accretion disks

Whether the existence of cold accretion disks around isolated, magnetized neutron stars might result in a distinct observational signature due to the Compton drag interaction between the electrostatically accelerated changes and the thermal radiation emitted by these disks. The particle dynamics resulting from the combined effects of electrostatic acceleration and the Compton drag interaction are determined. In the course of their deceleration, the charged particles boost the thermal disk radiation to gamma-ray energies, which may result in a significant spectral component. Cold disks are too underluminous to significantly retard the flow, and if such disks are present in pulsars, only a small fraction of the particle energy is transferred to the radiation field. The results also indicate that steady, unidirectional particle acceleration is unlikely to be the mechanism operating in gamma-ray burst sources.

Melia, Fulvio↗

NASA NTRS2020

An Electrical Modeling and Thermal Analysis Toolbox for Electrified Aircraft Propulsion Simulation

A simulation toolbox has been developed to model the electrical portions of Electrified Aircraft Propulsion (EAP) systems, including self-heating of electrical systems. Dynamic models of EAP systems often include turbomachinery, an electrical power system, and a thermal management system. These portions of the propulsion system can operate on timescales covering six orders of magnitude, which poses a challenging modeling task. Assumptions and approximations are made in an effort to capture the dynamics relevant to engine, electrical system, and thermal system interactions, while still allowing for fast simulations. These assumptions and approximations enable the electrical component models to run at the time scale of the turbomachinery, neglecting the very high frequency electrical dynamics, while demonstrating representative behavior of the end-to-end system. Thus the models execute in an acceptable time frame for what would otherwise be an extremely stiff simulation. The resulting simulations of EAP systems are appropriate for system-level control design and analysis. The objective of this paper is to present an overview of the Electrical Modeling and Thermal Analysis Toolbox (EMTAT). It will describe some of the approximations made to accommodate rapid execution, and some of the design tools that allow matching the model to component specifications. This paper will also provide some examples of EAP system modeling using EMTAT.

Mark E Bell↗

NASA NTRS2020

An Electrical Modeling and Thermal Analysis Toolbox for Electrified Aircraft Propulsion Simulation

A simulation toolbox has been developed to model the electrical portions of Electrified Aircraft Propulsion (EAP) systems, including self-heating of electrical systems. Dynamic models of EAP systems often include turbomachinery, an electrical power system, and a thermal management system. These portions of the propulsion system can operate on timescales covering six orders of magnitude, which poses a challenging modeling task. Assumptions and approximations are made in an effort to capture the dynamics relevant to engine, electrical system, and thermal system interactions, while still allowing for fast simulations. These assumptions and approximations enable the electrical component models to run at the time scale of the turbomachinery, neglecting the very high frequency electrical dynamics, while demonstrating representative behavior of the end-to-end system. Thus the models execute in an acceptable time frame for what would otherwise be an extremely stiff simulation. The resulting simulations of EAP systems are appropriate for system-level control design and analysis. The objective of this paper is to present an overview of the Electrical Modeling and Thermal Analysis Toolbox (EMTAT). It will describe some of the approximations made to accommodate rapid execution, and some of the design tools that allow matching the model to component specifications. This paper will also provide some examples of EAP system modeling using EMTAT.

Mark E Bell↗

NASA NTRS1986

Magnetized thermal conduction fronts

The evolution of planar thermal conduction fronts in the presence of a dynamically weak, but otherwise self-consistent, magnetic field is considered. The field is assumed to be connected and untangled. In the diffusion limit for the thermal conductivity, these fronts exhibit self-similar behavior, even in the presence of a field. The role of the field is restricted to channeling the heat flux along its lines of force, and it enters into the problem as a dimensionless angle variable. 'Combing' (or opening) of insulating field lines by the evaporative flow is explicitly demonstrated. Unless the field is nearly perpendicular to the front normal in the hot gas, insulating effects are not profound. Self-similarity breaks down if the front becomes saturated, and under certain conditions magnetized saturated conduction fronts cannot propagate: the solution characteristics of the wave equation form caustics. The physical resolution is the advent of two-fluid (nonlocal) heating. Such Coulomb-heated fronts are expected to be relatively rare in typical astrophysical systems. The large-scale effects of a magnetic field on cloud evaporation in the interstellar medium are briefly discussed, and it is suggested that these fields preclude the presence of time-independent evaporative solutions. Thermal interfaces may then continue to evolve until radiative cooling halts their development; large tracts of warm 10,000 K gas may result.

Balbus, S. A.↗

NASA NTRS2006

Analysis of a Cylindrical Specimen Heated by an Impinging Hot Hydrogen Jet

A computational conjugate heat transfer methodology was developed, as a first step towards an efficient and accurate multiphysics, thermo-fluid computational methodology to predict environments for hypothetical solid-core, nuclear thermal engine thrust chamber and components. A solid conduction heat transfer procedure was implemented onto a pressure-based, multidimensional, finite-volume, turbulent, chemically reacting, thermally radiating, and unstructured grid computational fluid dynamics formulation. The conjugate heat transfer of a cylindrical material specimen heated by an impinging hot hydrogen jet inside an enclosed test fixture was simulated and analyzed. The solid conduction heat transfer procedure was anchored with a standard solid heat transfer code. Transient analyses were then performed with ,variable thermal conductivities representing three composites of a material utilized as flow element in a legacy engine test. It was found that material thermal conductivity strongly influences the transient heat conduction characteristics. In addition, it was observed that high thermal gradient occur inside the cylindrical specimen during an impulsive or a 10 s ramp start sequence, but not during steady-state operations.

Wang, Ten-See↗

NASA NTRS2005

Evaluation of Microbolometer-Based Thermography for Gossamer Space Structures

In August 2003, NASA's In-Space Propulsion Program contracted with our team to develop a prototype on-board Optical Diagnostics System (ODS) for solar sail flight tests. The ODS is intended to monitor sail deployment as well as structural and thermal behavior, and to validate computational models for use in designing future solar sail missions. This paper focuses on the thermography aspects of the ODS. A thermal model was developed to predict local sail temperature variations as a function of sail tilt to the sun, billow depth, and spectral optical properties of front and back sail surfaces. Temperature variations as small as 0.5 C can induce significant thermal strains that compare in magnitude to mechanical strains. These thermally induced strains may result in changes in shape and dynamics. The model also gave insight into the range and sensitivity required for in-flight thermal measurements and supported the development of an ABAQUS-coupled thermo-structural model. The paper also discusses three kinds of tests conducted to 1) determine the optical properties of candidate materials; 2) evaluate uncooled microbolometer-type infrared imagers; and 3) operate a prototype imager with the ODS baseline configuration. (Uncooled bolometers are less sensitive than cooled ones, but may be necessary because of restrictive ODS mass and power limits.) The team measured the spectral properties of several coated polymer samples at various angles of incidence. Two commercially available uncooled microbolometer imagers were compared, and it was found that reliable temperature measurements are feasible for both coated and uncoated sides of typical sail membrane materials.

Miles, Jonathan J.↗

NASA NTRS1987

The role of ring current O(+) in the formation of stable auroral red arcs

Observations of thermal and energetic ion populations by the Dynamics Explorer 1 satellite in the magnetospheric energy source region as well as nearly simultaneous Langmuir probe measurements of enhanced electron temperatures by Dynamics Explorer 2 within the stable auroral red (SAR) arc at F region heights are used to examine the role of heavy ions in the formation of SAR arcs. It is found that sufficient energy is transferred to the electron gas at high altitudes via Coulomb collisions between the observed ring current ions and thermal electrons to support the enhanced F region electron temperatures measured on these field lines. The latitudinal variation in the electron heating rates calculated using observed ion populations is consistent with the observed variation in electron temperature across the SAR arc. In all cases, ring current O(+) is the major source of energy for the SAR arcs.

Kozyra, J. U.↗

NASA NTRS2008

Rescue Shuttle Flight Re-Entry: Controlling Astronaut Thermal Exposure

A rescue mission for the STS-125 Hubble Telescope Repair Mission requires reentry from space with 11 crew members aboard, exceeding past cabin thermal load experience and risking crew thermal stress potentially causing cognitive performance and physiological decrements. The space shuttle crew cabin air revitalization system (ARS) was designed to support a nominal crew complement of 4 to 7 crew and 10 persons in emergencies, all in a shirt-sleeve environment. Subsequent to the addition of full pressure suits with individual cooling units, the ARS cannot maintain a stable temperature in the crew cabin during reentry thermal loads. Bulk cabin thermal models, used for rescue mission planning and analysis of crew cabin air, were unable to accurately represent crew workstation values of air flow, carbon dioxide, and heat content for the middeck. Crew temperature models suggested significantly elevated core temperatures. Planning for an STS-400 potential rescue of seven stranded crew utilized computational fluid dynamics (CFD) models to demonstrate inhomogeneous cabin thermal properties and improve analysis compared to bulk models. In the absence of monitoring of crew temperature, heart rate, metabolic rate and incomplete engineering data on the performance of the integrated cooling garment/cooling unit (ICG/CU) at cabin temperatures above 75 degrees F, related systems & models were reevaluated and tests conducted with humans in the loop. Changes to the cabin ventilation, ICU placement, crew reentry suit-donning procedures, Orbiter Program wave-off policy and post-landing power down and crew extraction were adopted. A second CFD and core temperature model incorporated the proposed changes and confirmed satisfactory cabin temperature, improved air distribution, and estimated core temperatures within safe limits. CONCLUSIONS: These changes in equipment, in-flight and post-landing procedures, and policy were implemented for the STS-400 rescue shuttle & will be implemented in any future rescue flights from the International Space Station of stranded shuttle crews.

Gillis, David B.↗

NASA NTRS1989

The thermal catastrophe model of substorms

Equations are presented for the physical mechanisms involved in the resonant absorption of Alfven waves in the plasma sheet boundary layer. It is shown that energy absorbed by the plasma-sheet particles is a function of the central plasma sheet temperature. The heating curve, when coupled with convective transport, yielded an equation of state for the steady state plasma sheet, whose solution has the form of a mathematical catastrophe. The master equation includes dynamic terms describing the transition across the thermal catastrophe, making it possible to evaluate the time scale for the catastrophe to occur.

Goertz, C. K.↗

NASA NTRS1975

Two dimensional thermal and charge mapping of power thyristors

The two dimensional static and dynamic current density distributions within the junction of semiconductor power switching devices and in particular the thyristors were obtained. A method for mapping the thermal profile of the device junctions with fine resolution using an infrared beam and measuring the attenuation through the device as a function of temperature were developed. The results obtained are useful in the design and quality control of high power semiconductor switching devices.

Hu, S. P.↗

NASA NTRS2003

Relative Motion of Two Spacecraft Near the Sun-Earth L2 Point

Over the next two decades international space agencies including the National Aeronautics and Space Administration and the European Space Agency are proposing space missions which employ distributed spacecraft technologies to enable vast improvements in remote sensing performance as compared to fundamental performance limitations associated with fairing sizes of even the largest launch vehicles. These missions will require numerous advanced technologies to enable some extreme scientific goals. However, on the critical path to developing many of those technologies, understanding realistic achievable performance, and formulating such missions involving formation flying spacecraft, is the detailed understanding of the vehicle relative motion in the appropriate dynamic environment. Due to the appealing gravitational and thermal environment, the Sun-Earth L(sub 2) point is a strong candidate for placement of many of these missions. Henceforth, this paper begins to unravel the dynamics of relative motion near L(sub 2), with particular consideration given to the ultimate requirements for flying space- craft in precise formation. This work is meant to be a predecessor to detailed formation flying mission analysis efforts in the areas of formation design, formation control, and relative navigation.

Collange, Guillaume↗

NASA NTRS1979

Martian meteorology

Viking mission results concerning the structure and dynamics of the Martian atmosphere are reviewed. The large-scale variability of pressure, temperature, and zonally averaged wind at the Lander sites is described, and small-scale phenomena involving the boundary layer and internal gravity waves are discussed. Observational evidence for the existence of transient planetary-scale waves, forced quasi-stationary waves, and thermal tides on Mars is examined. Atmospheric dynamics and properties of dust storms are considered, with emphasis on dust properties and distribution, the time evolution of planetwide dust storms, and dust-storm genesis and decay. Attention is also given to the nature of past Martian climates, the sizes and composition of volatile reservoirs, and volatile escape from the atmosphere.

Leovy, C. B.↗

NASA NTRS2019

Dynamic RPS Path to Flight

NASA Glenn Research Center has been pursuing the development of dynamic power conversion for several decades. Candidate NASA missions involve mutli-year travel to far away destinations, or to extreme environments where sunlight does not exist. Human-base mission studies also show that power needs would be beyond the capabilities of solar energy conversion, and instead would require nuclear reactor energy sources, for which the thermal energy must be converted to electricity. Dynamic power conversion technology has developed sufficiently to make a sound engineering argument that it is suitable for these NASA missions. Dynamic conversion power sources have yet to be flown in space, and thus suffer a disadvantage owing to their lack of heritage data on flight missions. One of the largest obstacles for adoption is the uncertainty in reliability of a device with moving parts. However, significant progress has been made toward demonstrating the technology capable in all relevant environments, with the necessary long life. Another hurdle for adoption is the lack of mission, which would drive specific requirements, and provide a solid timeline for technology development endpoint. Until a mission is identified, an alternative approach is necessary to advance a dynamic power conversion system towards flight.

Oriti, Sal↗

NASA NTRS2019

Dynamic RPS Path to Flight - Nuclear and Emerging Technologies for Space

Oriti, Salvatore↗