SEARCH · Engineering Papers

Results for “structural modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

All sources NASA NTRS DOE OSTI

NASA NTRS1987

Slew maneuvers on the SCOLE Laboratory Facility

The Spacecraft Control Laboratory Experiment (SCOLE) was conceived to provide a physical test bed for the investigation of control techniques for large flexible spacecraft. The control problems studied are slewing maneuvers and pointing operations. The slew is defined as a minimum time maneuver to bring the antenna line-of-sight (LOS) pointing to within an error limit of the pointing target. The second objective is to rotate about the LOS within the 0.02 degree error limit. The SCOLE problem is defined as two design challenges: control laws for a mathematical model of a large antenna attached to the Space Shuttle by a long flexible mast; and a control scheme on a laboratory representation of the structure modelled on the control laws. Control sensors and actuators are typical of those which the control designer would have to deal with on an actual spacecraft. Computational facilities consist of microcomputer based central processing units with appropriate analog interfaces for implementation of the primary control system, and the attitude estimation algorithm. Preliminary results of some slewing control experiments are given.

Williams, Jeffrey P.↗

NASA NTRS2014

Pressure Sensitive Paint Applied to Flexible Models Project

One gap in current pressure-measurement technology is a high-spatial-resolution method for accurately measuring pressures on spatially and temporally varying wind-tunnel models such as Inflatable Aerodynamic Decelerators (IADs), parachutes, and sails. Conventional pressure taps only provide sparse measurements at discrete points and are difficult to integrate with the model structure without altering structural properties. Pressure Sensitive Paint (PSP) provides pressure measurements with high spatial resolution, but its use has been limited to rigid or semi-rigid models. Extending the use of PSP from rigid surfaces to flexible surfaces would allow direct, high-spatial-resolution measurements of the unsteady surface pressure distribution. Once developed, this new capability will be combined with existing stereo photogrammetry methods to simultaneously measure the shape of a dynamically deforming model in a wind tunnel. Presented here are the results and methodology for using PSP on flexible surfaces.

model deformation↗

NASA NTRS1988

Structural anomalies in undoped Gallium Arsenide observed in high resolution diffraction imaging with monochromatic synchrotron radiation

Novel, streak-like disruption features restricted to the plane of diffraction have recently been observed in images obtained by synchrotron radiation diffraction from undoped, semi-insulating gallium arsenide crystals. These features were identified as ensembles of very thin platelets or interfaces lying in (110) planes, and a structural model consisting of antiphase domain boundaries was proposed. We report here the other principal features observed in high resolution monochromatic synchrotron radiation diffraction images: (quasi) cellular structure; linear, very low-angle subgrain boundaries in (110) directions, and surface stripes in a (110) direction. In addition, we report systematic differences in the acceptance angle for images involving various diffraction vectors. When these observations are considered together, a unifying picture emerges. The presence of ensembles of thin (110) antiphase platelet regions or boundaries is generally consistent not only with the streak-like diffraction features but with the other features reported here as well. For the formation of such regions we propose two mechanisms, operating in parallel, that appear to be consistent with the various defect features observed by a variety of techniques.

Steiner, B.↗

NASA NTRS1989

Flutter of a Low-Aspect-Ratio Rectangular Wing

A flutter test of a low-aspect-ratio rectangular wing was conducted in the Langley Transonic Dynamics Tunnel (TDT). The model used in this flutter test consisted of a rigid wing mounted to the wind-tunnel wall by a flexible, rectangular beam. The flexible support shaft was connected to the wing root and was cantilever mounted to the wind-tunnel wall. The wing had an aspect ratio of 1.5 based on the wing semispan and an NACA 64A010 airfoil shape. The flutter boundary of the model was determined for a Mach number range of 0.5 to 0.97. The shape of the transonic flutter boundary was determined. Actual flutter points were obtained on both the subsonic and supersonic sides of the flutter bucket. The model exhibited a deep transonic flutter bucket over a narrow range of Mach number. At some Mach numbers, the flutter conditions were extrapolated using a subcritical response technique. In addition to the basic configuration, modifications were made to the model structure such that the first bending frequency was changed without significantly affecting the first torsion frequency. The experiment showed that increasing the bending stiffness of the model support shaft through these modifications lowered the flutter dynamic pressure. Flutter analysis was conducted for the basic model as a comparison with the experimental results. This flutter analysis was conducted with subsonic lifting-surface (kernel function) aerodynamics using the k method for the flutter solution.

Cole, Stanley R.↗

NASA NTRS1989

Structural anomalies in undoped gallium arsenide observed in high-resolution diffraction imaging with monochromatic synchrotron radiation

Steiner, B.↗

NASA NTRS1993

Finite element calculations of transonic flutter in cascades

Aeroelastic stability and response of turbomachinery cascades operating in the transonic regime are explored using a new computational approach. The two-dimensional unsteady Euler equations are used to model the transonic cascade flows, and the cascade blades are modeled as thin plates. To minimize the discretization incompatibility, both the fluid and the solid domains are discretized using finite element procedures. The fluid and the structural models are coupled at the element level by introducing a channel theory, which is analogous to a strip theory in the classical sense. The system of space-discretized equations is marched forward in time using an explicit four-stage Runge-Kutta scheme. Results of free vibration analyses of typical blades are presented and compared to published finite element and Rayleigh-Ritz results. Aeroelastic stability and response characteristics of several transonic cascades are investigated using the new quasi-3D model. These results demonstrate the present 3D finite element blade model is capable of capturing aeroelastic instabilities involving higher modes, including (plate-type) camber bending modes.

Hsiao, Chingteng↗

NASA NTRS1997

Wing Weight Optimization Under Aeroelastic Loads Subject to Stress Constraints

A minimum weight optimization of the wing under aeroelastic loads subject to stress constraints is carried out. The loads for the optimization are based on aeroelastic trim. The design variables are the thickness of the wing skins and planform variables. The composite plate structural model incorporates first-order shear deformation theory, the wing deflections are expressed using Chebyshev polynomials and a Rayleigh-Ritz procedure is adopted for the structural formulation. The aerodynamic pressures provided by the aerodynamic code at a discrete number of grid points is represented as a bilinear distribution on the composite plate code to solve for the deflections and stresses in the wing. The lifting-surface aerodynamic code FAST is presently being used to generate the pressure distribution over the wing. The envisioned ENSAERO/Plate is an aeroelastic analysis code which combines ENSAERO version 3.0 (for analysis of wing-body configurations) with the composite plate code.

Kapania, Rakesh K.↗

NASA NTRS2001

Stochastic Modeling and Generation of Partially Polarized or Partially Coherent Electromagnetic Waves

Many new Earth remote-sensing instruments are embracing both the advantages and added complexity that result from interferometric or fully polarimetric operation. To increase instrument understanding and functionality a model of the signals these instruments measure is presented. A stochastic model is used as it recognizes the non-deterministic nature of any real-world measurements while also providing a tractable mathematical framework. A stationary, Gaussian-distributed model structure is proposed. Temporal and spectral correlation measures provide a statistical description of the physical properties of coherence and polarization-state. From this relationship the model is mathematically defined. The model is shown to be unique for any set of physical parameters. A method of realizing the model (necessary for applications such as synthetic calibration-signal generation) is given and computer simulation results are presented. The signals are constructed using the output of a multi-input multi-output linear filter system, driven with white noise.

Davis, Brynmor↗

NASA NTRS2008

External Tank (ET) Foam Thermal/Structural Analysis Project

An independent study was performed to assess the pre-launch thermally induced stresses in the Space Shuttle External Tank Bipod closeout and Ice/Frost ramps (IFRs). Finite element models with various levels of detail were built that included the three types of foam (BX-265, NCFI 24-124, and PDL 1034) and the underlying structure and bracketry. Temperature profiles generated by the thermal analyses were input to the structural models to calculate the stress levels. An area of high stress in the Bipod closeout was found along the aluminum tank wall near the phenolic insulator and along the phenolic insulator itself. This area of high stress might be prone to cracking and possible delamination. There is a small region of slightly increased stress in the NCFI 24-124 foam near its joint with the Bipod closeout BX-265 foam. The calculated stresses in the NCFI 24-124 acreage foam are highest at the NCFI 24-124/PDL 1034/tank wall interface under the LO2 and LH2 IFRs. The highest calculated stresses in the LH2 NCFI 24-124 foam are higher than in similar locations in the LO2 IFR. This finding is consistent with the dissection results of IFRs on ET-120.

Moore, David F.↗

NASA NTRS2014

A Population Pharmacokinetic Model for Disposition in Plasma, Saliva and Urine of Scopolamine after Intranasal Administration to Healthy Human Subjects

An intranasal gel formulation of scopolamine (INSCOP) was developed for the treatment of Space Motion Sickness. The bioavailability and pharmacokinetics (PK) were evaluated under the Food and Drug Administration guidelines for clinical trials with an Investigative New Drug (IND) protocol. The aim of this project was to develop a PK model that can predict the relationship between plasma, saliva and urinary scopolamine concentrations using data collected from the IND clinical trials with INSCOP. Methods: Twelve healthy human subjects were administered three dose levels (0.1, 0.2 and 0.4 mg) of INSCOP. Serial blood, saliva and urine samples were collected between 5 min and 24 h after dosing and scopolamine concentrations were measured by using a validated LC‐MS‐MS assay. Pharmacokinetic Compartmental models, using actual dosing and sampling times, were built using Phoenix (version 1.2). Model selection was based on the likelihood ratio test on the difference of criteria (‐2LL) and comparison of the quality of fit plots. Results: The best structural model for INSCOP (minimal ‐2LL= 502.8) was established. It consisted of one compartment each for plasma, saliva and urine, respectively, which were connected with linear transport processes except the nonlinear PK process from plasma to saliva compartment. The best‐fit estimates of PK parameters from individual PK compartmental analysis and Population PK model analysis were shown in Tables 1 and 2, respectively. Conclusion: A population PK model that could predict population and individual PK of scopolamine in plasma, saliva and urine after dosing was developed and validated. Incorporating a non‐linear transfer from plasma to saliva compartments resulted in a significantly improved model fitting. The model could be used to predict scopolamine plasma concentrations from salivary and urinary drug levels, allowing non‐invasive therapeutic monitoring of scopolamine in space and other remote environments.

Wu, L.↗

NASA NTRS1982

Order reduction for models of space structures using modal cost analysis

Modal cost analysis furnishes a promising methodology for developing dynamical models of space structures for use in control systems analysis. Economy and accuracy can be attained by only retaining vibration modes that contribute significantly to an appropriately defined cost function. Expressions for modal costs (especially simple for 'lightly damped' structures) are derived for attitude control, vibration suppression, and shape control. These techniques are illustrated through application to a high-order finite element model of a large platform-type structure.

Skelton, R. E.↗

NASA NTRS1986

A comparative study of prebiotic and present day translational models

It is generally recognized that the understanding of the molecular basis of primitive translation is a fundamental step in developing a theory of the origin of life. However, even in modern molecular biology, the mechanism for the decoding of messenger RNA triplet codons into an amino acid sequence of a protein on the ribosome is understood incompletely. Most of the proposed models for prebiotic translation lack, not only experimental support, but also a careful theoretical scrutiny of their compatibility with well understood stereochemical and energetic principles of nucleic acid structure, molecular recognition principles, and the chemistry of peptide bond formation. Present studies are concerned with comparative structural modelling and mechanistic simulation of the decoding apparatus ranging from those proposed for prebiotic conditions to the ones involved in modern biology. Any primitive decoding machinery based on nucleic acids and proteins, and most likely the modern day system, has to satisfy certain geometrical constraints. The charged amino acyl and the peptidyl termini of successive adaptors have to be adjacent in space in order to satisfy the stereochemical requirements for amide bond formation. Simultaneously, the same adaptors have to recognize successive codons on the messenger. This translational complex has to be realized by components that obey nucleic acid conformational principles, stabilities, and specificities. This generalized condition greatly restricts the number of acceptable adaptor structures.

Rein, R.↗

NASA NTRS1976

Model for thickness dependence of radiation charging in MOS structures

The model considers charge buildup in MOS structures due to hole trapping in the oxide and the creation of sheet charge at the silicon interface. The contribution of hole trapping causes the flatband voltage to increase with thickness in a manner in which square and cube dependences are limiting cases. Experimental measurements on samples covering a 200 - 1000 A range of oxide thickness are consistent with the model, using independently obtained values of hole-trapping parameters. An important finding of our experimental results is that a negative interface charge contribution due to surface states created during irradiation compensates most of the positive charge in the oxide at flatband. The tendency of the surface states to 'track' the positive charge buildup in the oxide, for all thicknesses, applies both in creation during irradiation and in annihilation during annealing. An explanation is proposed based on the common defect origin of hole traps and potential surface states.

Viswanathan, C. R.↗

NASA NTRS1976

The relativistic equations of stellar structure and evolution. Stars with degenerate neutron cores. 1: Structure of equilibrium models

The general relativistic equations of stellar structure and evolution are reformulated in a notation which makes easy contact with Newtonian theory. Also, a general relativistic version of the mixing-length formalism for convection is presented. Finally, it is argued that in previous work on spherical systems general relativity theorists have identified the wrong quantity as "total mass-energy inside radius r."

Thorne, K. S.↗

NASA NTRS1999

Modeling the Atmospheric Structure and Dynamics of the Martian Atmosphere

Models of the general circulation and climate system of Mars have reached a high level of maturity, but observations to validate them have lacked the kind of global and temporal coverage required. However, we are now on the verge of a new era in Mars exploration as Mars Global Surveyor, and the now enroute Mars Climate Orbiter, will provide daily global coverage of the atmosphere for two Mars years. In the coming years, data from these missions will test the predictions of general circulation models (GCM's) whose results have perhaps become too accepted as truth. This talk will review what GCM's tell us about Mars, what their weaknesses are, and what the latest results imply for their future. Additional information is contained in the original extended abstract.

Haberle, R. M.↗

NASA NTRS1967

Adaptive age replacement.

Loss structure models concerning age replacement policies, discussing mathematical aspects of maintenance with dynamic programming formulation

COST ESTIMATE↗

NASA NTRS1972

Automated preliminary design of simplified wing structures to satisfy strength and flutter requirements

A simple structural model of an aircraft wing is used to show the effects of strength (stress) and flutter requirements on the design of minimum-weight aircraft-wing structures. The wing is idealized as an isotropic sandwich plate with a variable cover thickness distribution and a variable depth between covers. Plate theory is used for the structural analysis, and piston theory is used for the unsteady aerodynamics in the flutter analysis. Mathematical programming techniques are used to find the minimum-weight cover thickness distribution which satisfies flutter, strength, and minimum-gage constraints. The method of solution, some sample results, and the computer program used to obtain these results are presented. The results indicate that the cover thickness distribution obtained when designing for the strength requirement alone may be quite different from the cover thickness distribution obtained when designing for either the flutter requirement alone or for both the strength and flutter requirements concurrently. This conclusion emphasizes the need for designing for both flutter and strength from the outset.

Stroud, W. J.↗

NASA NTRS1990

Behavior of composite/metal aircraft structural elements and components under crash type loads: What are they telling us

Failure behavior results are presented from crash dynamics research using concepts of aircraft elements and substructure not necessarily designed or optimized for energy absorption or crash loading considerations. To achieve desired new designs which incorporate improved energy absorption capabilities often requires an understanding of how more conventional designs behave under crash loadings. Experimental and analytical data are presented which indicate some general trends in the failure behavior of a class of composite structures which include individual fuselage frames, skeleton subfloors with stringers and floor beams but without skin covering, and subfloors with skin added to the frame-stringer arrangement. Although the behavior is complex, a strong similarity in the static and dynamic failure behavior among these structures is illustrated through photographs of the experimental results and through analytical data of generic composite structural models. It is believed that the similarity in behavior is giving the designer and dynamists much information about what to expect in the crash behavior of these structures and can guide designs for improving the energy absorption and crash behavior of such structures.

Carden, Huey D.↗