SEARCH · Engineering Papers

Results for “standardized data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

All sources NASA NTRS DOE OSTI

NASA NTRS1983

Comparison of low-altitude wind-shear statistics derived from measured and proposed standard wind profiles

Wind shear statistics were calculated for a simulated set of wind profiles based on a proposed standard wind field data base. Wind shears were grouped in altitude in altitude bands of 100 ft between 100 and 1400 ft and in wind shear increments of 0.025 knot/ft. Frequency distributions, means, and standard deviations for each altitude band were derived for the total sample were derived for both sets. It was found that frequency distributions in each altitude band for the simulated data set were more dispersed below 800 ft and less dispersed above 900 ft than those for the measured data set. Total sample frequency of occurrence for the two data sets was about equal for wind shear values between +0.075 knot/ft, but the simulated data set had significantly larger values for all wind shears outside these boundaries. It is shown that normal distribution in both data sets neither data set was normally distributed; similar results are observed from the cumulative frequency distributions.

Usry, J. W.↗

NASA NTRSDate not supplied

High Speed Data Investigation of an LOX/LNG Combustor Assisted by Non-linear Acoustic Simulations

During testing of a regenerative cooled liquid oxygen/liquid natural gas combustor large amplitude combustion instabilities were observed in half of the series conducted. These instabilities produced an unsteady pressure Root Mean Square (RMS) value greater than the chamber steady state pressure. Quick look investigations of the test data presented some standard indications of non-linear tangential instability such as a non-sinusoidal time series, and larger peaks than trough. Also observed in the data quick look were some atypical findings including a first harmonic amplitude larger than the fundamental, and numerous side bands on the fundamental and subsequent harmonics. A simplified model of the combustor was created using a commercially available finite element software. The first tangential acoustic mode was then simulated using a non-linear wave equation in conjunction with a time explicit discontinuous Gelarkin flow solver. Numerous simulations were evaluated providing valuable insight and reproducing the atypical findings in the data. Side bands were created through non-linear signal modulation like an AM radio. This happens due to the non-linear steepening and relaxing that occurs in large amplitude oscillations. The simulation was also able to reproduce a signal with a first harmonic amplitude larger than the fundamental. Investigating the pressure signal at multiple locations across the chamber head end revealed radial dependent frequency content. A literature review of the topic revealed corroboration of these effect in idealized geometries.

Combustion Stability↗

NASA NTRSDate not supplied

High Speed Data Investigation of an LOX/LNG Combustor Assisted by Non-linear Acoustic Simulations

Combustion Stability↗

NASA NTRS2001

Non-Deterministic, Non-Traditional Methods (NDNTM)

The review effort identified research opportunities related to the use of nondeterministic, nontraditional methods to support aerospace design. The scope of the study was restricted to structural design rather than other areas such as control system design. Thus, the observations and conclusions are limited by that scope. The review identified a number of key results. The results include the potential for NASA/AF collaboration in the area of a design environment for advanced space access vehicles. The following key points set the context and delineate the key results. The Principal Investigator's (PI's) context for this study derived from participation as a Panel Member in the Air Force Scientific Advisory Board (AF/SAB) Summer Study Panel on 'Whither Hypersonics?' A key message from the Summer Study effort was a perceived need for a national program for a space access vehicle whose operating characteristics of cost, availability, deployability, and reliability most closely match the NASA 3rd Generation Reusable Launch Vehicle (RLV). The Panel urged the AF to make a significant joint commitment to such a program just as soon as the AF defined specific requirements for space access consistent with the AF Aerospace Vision 2020. The review brought home a concurrent need for a national vehicle design environment. Engineering design system technology is at a time point from which a revolution as significant as that brought about by the finite element method is possible, this one focusing on information integration on a scale that far surpasses current design environments. The study therefore fully supported the concept, if not some of the details of the Intelligent Synthesis Environment (ISE). It became abundantly clear during this study that the government (AF, NASA) and industry are not moving in the same direction in this regard, in fact each is moving in its own direction. NASA/ISE is not yet in an effective leadership position in this regard. However, NASA does have complementary software interoperability efforts that should be a part of any major ISE program. Software standards that assure interoperability of data systems and modeling representations are enabling for the proposed research advocated herein and should be a major element in the ISE initiative. The international standard for data interchange is known by the acronym 'STEP.' The NASA participation and lead for that effort is at the Goddard Space Flight Center. NASA/GRC is leading an effort to define CAD geometry standards through the Object Management Group (OMG). To enable the design environment so necessary to the above national vision for a unique space vehicle will require an integrating software environment with interoperability standards that allow the development and widespread deployment of tools and toolsets, rather than traditional "shrink-wrapped" software used by engineers today.

Cruse, Thomas A.↗

NASA NTRS2000

BOREAS RSS-14 Level -3 Gridded Radiometer and Satellite Surface Radiation Images

The BOREAS RSS-14 team collected and processed GOES-7 and -8 images of the BOREAS region as part of its effort to characterize the incoming, reflected, and emitted radiation at regional scales. This data set contains surface radiation parameters, such as net radiation and net solar radiation, that have been interpolated from GOES-7 images and AMS data onto the standard BOREAS mapping grid at a resolution of 5 km N-S and E-W. While some parameters are taken directly from the AMS data set, others have been corrected according to calibrations carried out during IFC-2 in 1994. The corrected values as well as the uncorrected values are included. For example, two values of net radiation are provided: an uncorrected value (Rn), and a value that has been corrected according to the calibrations (Rn-COR). The data are provided in binary image format data files. Some of the data files on the BOREAS CD-ROMs have been compressed using the Gzip program. See section 8.2 for details. The data files are available on a CD-ROM (see document number 20010000884), or from the Oak Ridge National Laboratory (ORNL) Distributed Active Archive Center (DAAC).

Hall, Forrest G.↗

NASA NTRS2016

CSW Best Practices

During the development of the CMR (Common Metadata Repository) (CMR) for the Earth Observing System Data and Information System (EOSDIS), CSW (Catalog Service for the Web) a number of best practices came to light. Given that the ESIP (Earth Science Information Partners) Discovery Cluster is committed to interoperability and standards in earth data discovery this seemed like a convenient moment to provide Best Practices to the organization in the same way we did for OpenSearch for this widely-used standard.

CMR↗

NASA NTRS2012

Correlation of Helium Solubility in Liquid Nitrogen

A correlation has been developed for the equilibrium mole fraction of soluble gaseous helium in liquid nitrogen as a function of temperature and pressure. Experimental solubility data was compiled and provided by National Institute of Standards and Technology (NIST). Data from six sources was used to develop a correlation within the range of 0.5 to 9.9 MPa and 72.0 to 119.6 K. The relative standard deviation of the correlation is 6.9 percent.

VanDresar, Neil T.↗

NASA NTRS1993

Standards in the architectural effort

The NASA Scientific and Technical Information (STI) Project Architecture Group was established to build a framework for modernization, provide guidance and direction for standardization and integration efforts, and to develop a set of concepts, interfaces, and entities to specifiy standards. The STI data processing architecture is a set of diagrams and descriptions that characterize the principal functions and services as well as hardware and software components. The use of standards promotes scalability and interchangeability.

Markham, Howard↗

NASA NTRSDate not supplied

Improving Sim-to-Real Transfer in Vision-Based Robot Navigation Via Instance-Level GAN-Based Data Augmentation

Achieving robust vision-based robotic tasks requires large amounts of data, which are often difficult to obtain in real-world scenarios. Simulators and synthetic data offer a cost-effective alternative, but the visual gap between simulation and reality hinders the performance of models when deployed in real-world environments. In this paper, we present a data augmentation pipeline that integrates a foundation model (Segment Anything Model) with an unsupervised image-to-image translation model (CycleGAN) for instance-level domain transfer from simulation to reality. This pipeline enables the generation of realistic labeled data from synthetic images for training supervised machine learning models in vision-based navigation tasks. We evaluate our approach on real-world data for ego-vehicle pose estimation, a critical autonomous navigation task involving the prediction of cross-track position and heading angle relative to road center line markings. The results of our tests show that our GAN-based data augmentation pipeline significantly outperforms models trained solely on simulation data or on data processed with standard image augmentation methods for sim-to-real transfer, enhancing model robustness and generalizability in real-world scenarios. Our method provides a scalable and flexible data augmentation tool for leveraging large synthetic datasets to enhance vision-based robotic navigation tasks.

artificial intelligence↗

NASA NTRS1981

RAWINPROC: Computer program for decommutating, interpreting, and interpolating Rawinsonde meteorological balloon sounding data

The FORTRAN computer program RAWINPROC accepts output from NASA Wallops computer program METPASS1; and produces input for NASA computer program 3.0.0700 (ECC-PRD). The three parts together form a software system for the completely automatic reduction of standard RAWINSONDE sounding data. RAWINPROC pre-edits the 0.1-second data, including time-of-day, azimuth, elevation, and sonde-modulated tone frequency, condenses the data according to successive dwells of the tone frequency, decommutates the condensed data into the proper channels (temperature, relative humidity, high and low references), determines the running baroswitch contact number and computes the associated pressure altitudes, and interpolates the data appropriate for input to ACC-PRD.

Staffanson, F. L.↗

NASA NTRS1977

Necessity to adapt land use and land cover classification systems to readily accept radar data

A hierarchial, four level, standardized system for classifying land use/land cover primarily from remote-sensor data (USGS system) is described. The USGS system was developed for nonmicrowave imaging sensors such as camera systems and line scanners. The USGS system is not compatible with the land use/land cover classifications at different levels that can be made from radar imagery, and particularly from synthetic-aperture radar (SAR) imagery. The use of radar imagery for classifying land use/land cover at different levels is discussed, and a possible revision of the USGS system to more readily accept land use/land cover classifications from radar imagery is proposed.

Drake, B.↗

NASA NTRS1996

BATSE Observations of Gamma-Ray Burst Spectra: Low-Energy Behavior of Time-Averaged Spectra - Part 3

We analyze time-averaged spectra from 86 bright gamma-ray bursts from the first 5 years of the Burst And Transient Source Experiment (BATSE) on board the Compton Gamma Ray Observatory to determine whether the lowest energy data are consistent with a standard spectra form fit to the data at all energies. The BATSE Spectroscopy Detectors have the capability to observe photons as low as 5 keV. Using the gamma-ray burst locations obtained with the BATSE Large Area Detectors, the Spectroscopy Detectors' low-energy response can be modeled accurately. This, together with a postlaunch calibration of the lowest energy Spectroscopy Detector discriminator channel, which can lie in the range 5-20 keV, allows spectral deconvolution over a broad energy range, approx. 5 keV to 2 MeV. The additional coverage allows us to search for evidence of excess emission, or for a deficit, below 20 keV. While no burst has a significant (greater than or equal to 3 sigma) deficit relative to a standard spectra model, we find that 12 bursts have excess low-energy emission, ranging between 1.2 and 5.8 times the model flux, that exceeds 5 sigma in significance. This is evidence for an additional low-energy spectral component in at least some bursts, or for deviations from the power-law spectral form typically used to model gamma-ray bursts at energies below 100 keV.

Preece, R. D.↗

NASA NTRS1984

Some methods of computing platform transmitter terminal location estimates

A position estimation algorithm was developed to track a humpback whale tagged with an ARGOS platform after a transmitter deployment failure and the whale's diving behavior precluded standard methods. The algorithm is especially useful where a transmitter location program exists; it determines the classical keplarian elements from the ARGOS spacecraft position vectors included with the probationary file messages. A minimum of three distinct messages are required. Once the spacecraft orbit is determined, the whale is located using standard least squares regression techniques. Experience suggests that in instances where circumstances inherent in the experiment yield message data unsuitable for the standard ARGOS reduction, (message data may be too sparse, span an insufficient period, or include variable-length messages). System ARGOS can still provide much valuable location information if the user is willing to accept the increased location uncertainties.

Hoisington, C. M.↗

NASA NTRS1991

Space Station Freedom coupling tasks: An evaluation of their space operational compatibility

The development of the Space Station Freedom tasks that are compatible with both telerobotic as well as extravehicular activity is a necessary redundancy in order to insure successful day to day operation. One task to be routinely performed aboard Freedom will be the changeout of various quick disconnect fluid connectors. In an attempt to resolve these potentially contradictory issues of compatibility, mock-ups of couplings suitable to both extravehicular as well as telerobotic activity were designed and built. An evaluation performed at the Remote Operator Interaction Laboratory at NASA's Johnson Space Center is discussed, which assessed the prototype couplings as well as three standard coupling designs. Data collected during manual and telerobotic manipulation of the couplings indicated that the custom coupling was in fact shown to be faster to operate and generally preferred over the standard coupling designs.

Sampaio, Carlos E.↗

NASA NTRS1994

Amazon Rain Forest Classification Using J-ERS-1 SAR Data

The Amazon rain forest is a region of the earth that is undergoing rapid change. Man-made disturbance, such as clear cutting for agriculture or mining, is altering the rain forest ecosystem. For many parts of the rain forest, seasonal changes from the wet to the dry season are also significant. Changes in the seasonal cycle of flooding and draining can cause significant alterations in the forest ecosystem.Because much of the Amazon basin is regularly covered by thick clouds, optical and infrared coverage from the LANDSAT and SPOT satellites is sporadic. Imaging radar offers a much better potential for regular monitoring of changes in this region. In particular, the J-ERS-1 satellite carries an L-band HH SAR system, which via an on-board tape recorder, can collect data from almost anywhere on the globe at any time of year.In this paper, we show how J-ERS-1 radar images can be used to accurately classify different forest types (i.e., forest, hill forest, flooded forest), disturbed areas such as clear cuts and urban areas, and river courses in the Amazon basin. J-ERS-1 data has also shown significant differences between the dry and wet season, indicating a strong potential for monitoring seasonal change. The algorithm used to classify J-ERS-1 data is a standard maximum-likelihood classifier, using the radar image local mean and standard deviation of texture as input. Rivers and clear cuts are detected using edge detection and region-growing algorithms. Since this classifier is intended to operate successfully on data taken over the entire Amazon, several options are available to enable the user to modify the algorithm to suit a particular image.

J-ERS-1↗

NASA NTRS2015

Thermal Testing and Model Correlation of the Magnetospheric Multiscale (MMS) Observatories

International Conference on Envronmental Systems (ICES), Seattle WA NCTS 20964-15. The Magnetospheric Multiscale (MMS) mission is a Solar Terrestrial Probes mission comprising four identically instrumented spacecraft that will use Earths magnetosphere as a laboratory tostudy the microphysics of three fundamental plasma processes: magnetic reconnection, energetic particle acceleration, and turbulence. This paper presents the complete thermal balance (TB) test performed on the first of four observatories to go through thermal vacuum (TV) and the minibalance testing that was performed on the subsequent observatories to provide a comparison of all four. The TV and TB tests were conducted in a thermal vacuum chamber at the Naval Research Laboratory (NRL) in Washington, D.C. with the vacuum level higher than 1.3 x 10-4 Pa (10-6 torr)and the surrounding temperature achieving -180 C. Three TB test cases were performed that included hot operational science, cold operational science and a cold survival case. In addition to the three balance cases a two hour eclipse and a four hour eclipse simulation was performed during the TV test to provide additional transient data points that represent the orbit in eclipse (or Earth's shadow) The goal was to perform testing such that the flight orbital environments could be simulated as closely as possible. A thermal model correlation between the thermal analysis and the test results was completed. Over 400 1-Wire temperature sensors, 200 thermocouples and 125 flight thermistor temperature sensors recorded data during TV and TB testing. These temperatureversus time profiles and their agreements with the analytical results obtained using Thermal Desktop and SINDAFLUINT are discussed. The model correlation for the thermal mathematical model (TMM) is conducted based on the numerical analysis results and the test data. The philosophy of model correlation was to correlate the model to within 3 C of the test data using the standard deviation and mean deviation error calculation. Individual temperature error goal is to be within 5 C and the heater power goal is to be within 5 of test data. The results of the model correlation are discussed and the effect of some material and interface parameters on the temperature profiles are presented.

Thermal↗

NASA NTRS1998

Statistical Treatment of Earth Observing System Pyroshock Separation Test Data

The Earth Observing System (EOS) AM-1 spacecraft for NASA's Mission to Planet Earth is scheduled to be launched on an Atlas IIAS vehicle in June of 1998. One concern is that the instruments on the EOS spacecraft are sensitive to the shock-induced vibration produced when the spacecraft separates from the launch vehicle. By employing unique statistical analysis to the available ground test shock data, the NASA Lewis Research Center found that shock-induced vibrations would not be as great as the previously specified levels of Lockheed Martin. The EOS pyroshock separation testing, which was completed in 1997, produced a large quantity of accelerometer data to characterize the shock response levels at the launch vehicle/spacecraft interface. Thirteen pyroshock separation firings of the EOS and payload adapter configuration yielded 78 total measurements at the interface. The multiple firings were necessary to qualify the newly developed Lockheed Martin six-hardpoint separation system. Because of the unusually large amount of data acquired, Lewis developed a statistical methodology to predict the maximum expected shock levels at the interface between the EOS spacecraft and the launch vehicle. Then, this methodology, which is based on six shear plate accelerometer measurements per test firing at the spacecraft/launch vehicle interface, was used to determine the shock endurance specification for EOS. Each pyroshock separation test of the EOS spacecraft simulator produced its own set of interface accelerometer data. Probability distributions, histograms, the median, and higher order moments (skew and kurtosis) were analyzed. The data were found to be lognormally distributed, which is consistent with NASA pyroshock standards. Each set of lognormally transformed test data produced was analyzed to determine if the data should be combined statistically. Statistical testing of the data's standard deviations and means (F and t testing, respectively) determined if data sets were significantly different at a 95-percent confidence level. If two data sets were found to be significantly different, these families of data were not combined for statistical purposes. This methodology produced three separate statistical data families of shear plate data. For each population, a P99.1/50 (probability/confidence) per-separation-nut firing level was calculated. By using the binomial distribution, Lewis researchers determined that this pernut firing level was equivalent to a P95/50 per-flight confidence level. The overall envelope of the per-flight P95/50 levels led to Lewis' recommended EOS interface shock endurance specification. A similar methodology was used to develop Lewis' recommended EOS mission assurance levels. The available test data for the EOS mission are significantly larger than for a normal mission, thus increasing the confidence level in the calculated expected shock environment. Lewis significantly affected the EOS mission by properly employing statistical analysis to the data. This analysis prevented a costly requalification of the spacecraft's instruments, which otherwise would have been exposed to significantly higher test levels.

McNelis, Anne M.↗

NASA NTRS1978

Preliminary design for a standard 10 sup 7 bit Solid State Memory (SSM)

A modular concept with three separate modules roughly separating bubble domain technology, control logic technology, and power supply technology was employed. These modules were respectively the standard memory module (SMM), the data control unit (DCU), and power supply module (PSM). The storage medium was provided by bubble domain chips organized into memory cells. These cells and the circuitry for parallel data access to the cells make up the SMM. The DCU provides a flexible serial data interface to the SMM. The PSM provides adequate power to enable one DCU and one SMM to operate simultaneously at the maximum data rate. The SSM was designed to handle asynchronous data rates from dc to 1.024 Mbs with a bit error rate less than 1 error in 10 to the eight power bits. Two versions of the SSM, a serial data memory and a dual parallel data memory were specified using the standard modules. The SSM specification includes requirements for radiation hardness, temperature and mechanical environments, dc magnetic field emission and susceptibility, electromagnetic compatibility, and reliability.

Hayes, P. J.↗