Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “shear”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

Wind Shear and Wind Veer Effects on Wind Turbines

This chapter highlights key contributions to the scientific literature on the sources of wind shear and wind veer in the atmospheric boundary layer, observations of shear and veer, and the effects of shear and veer on wind turbine power production, wind turbine wake evolution, and wind turbine loads. As wind turbines have grown larger, they encounter deeper and more complicated regions of the atmosphere. Over this height, profiles of wind speed shear and wind direction veer play a quantifiable role. Changes in the wind speed and wind direction across the vertical extent of a wind turbine rotor disk modify the inflow vector on the blades of the turbine, thereby affecting the magnitude and orientation of the lift and drag forces of the blade's airfoil. These changes can affect the power production and loads on large modern turbines, as well as the evolution of the wake that could affect a downwind turbine.

atmospheric stability↗

X-ray Scattering Measurements of Particle Orientation in a Sheared Polymer/Clay Dispersion

We report steady and transient measurements of particle orientation in a clay dispersion subjected to shear flow. An organically modified clay is dispersed in a Newtonian polymer matrix at a volume fraction of 0.02, using methods previously reported by Mobuchon et al. (Rheol Acta 46: 1045, 2007). In accord with prior studies, mechanical rheometry shows yield stress-like behavior in steady shear, while time dependent growth of modulus is observed following flow cessation. Measurements of flow-induced orientation in the flow-gradient plane of simple shear flow using small-angle and wide-angle X-ray scattering (SAXS and WAXS) are reported. Both SAXS and WAXS reveal increasing particle orientation as shear rate is increased. Partial relaxation of nanoparticle orientation upon flow cessation is well correlated with time-dependent changes in complex modulus. SAXS and WAXS data provide qualitatively similar results; however, some quantitative differences are attributed to differences in the length scales probed by these techniques.

36 MATERIALS SCIENCE↗

Study on Texture Evolution and Shear Behavior of an Al/Ni/Cu Composite

The microstructure, texture, and mechanical properties of the Al/Ni/Cu composite during various accumulative roll bonding (ARB) cycles were studied using optical microscopy, scanning electron microscopy, x-ray diffraction, shear punch test, and hardness test. In addition, ImageJ software and Rietveld software were used in order to study microstructure and dislocation density variations, respectively. It was found that Ni and Cu layers were fractured and distributed in the Al matrix due to differences in their mechanical properties. Fracture and distribution of Cu and Ni particles after cycle five led to the alteration of the composite structure from a layered to a particle-reinforced structure. ARB process leads to the formation of strong orientation along the β-fiber and also to pronounced copper and dillamore components in both Al and Cu phases. Furthermore, the shear yield stress and ultimate shear strength of the composite increased as the ARB process advanced; however, shear elongation presented a non-uniform variation. Investigation of the fracture surfaces revealed that the mechanical properties of the composite are affected not only by the strain hardening of the Cu layer, but also by the structural change in the composite during the initial ARB cycles. During the last stages of the process, however, changes in mechanical properties were mostly governed by reinforcement particles serving as strain concentration zones and the strain hardening of the Al matrix.

36 MATERIALS SCIENCE↗

Microstructure and Mechanical Properties of the AA7075 Tube Fabricated using Shear Assisted Processing and Extrusion (ShAPE)

Shear Assisted Processing and Extrusion (ShAPE) experimental setup and tooling were adopted for extruding thin-walled AA7075 aluminum tube from as-cast non-homogenized billet material in a single run. The mechanical and microstructural characterizations were performed on the extrudate in the as-extruded condition without subsequent heat treating. It was shown that the ShAPE process developed a significantly refined microstructure with uniform and almost equiaxed grain structure on both hoop and axial cross-sections of the extrudate as well as through the thickness of the material. The pole figures and inverse pole figures of the EBSD data showed an strong shear texture development, and it was found out that axial shear is the dominant deformation mechanism in the regions near the inner surface of the tube, while combined axial and torsional shears are the two dominant modes of deformation near the outer surface of the extrudate. As for the mechanical properties, there was an increase of 150% and 73% in the yield and ultimate strengths of the tube produced using ShAPE process, respectively, and a 18% decrease in maximum uniform plastic elongation compared to the conventionally extruded AA7075-O tube.

Shear Assisted Processing and Extrusion, Friction ↗

Studies of Shear Band Velocity Using Spatially and Temporally Resolved Measurements of Strain During Quasistatic Compression of Bulk Metallic Glass

We have made measurements of the temporal and spatial features of the evolution of strain during the serrated flow of Pd{sub 40}Ni{sub 40}P{sub 20} bulk metallic glass tested under quasistatic, room temperature, uniaxial compression. Strain and load data were acquired at rates of up to 400 kHz using strain gages affixed to all four sides of the specimen and a piezoelectric load cell located near the specimen. Calculation of the displacement rate requires an assumption about the nature of the shear displacement. If one assumes that the entire shear plane displaces simultaneously, the displacement rate is approximately 0.002 m/s. If instead one assumes that the displacement occurs as a localized propagating front, the velocity of the front is approximately 2.8 m/s. In either case, the velocity is orders of magnitude less than the shear wave speed ({approx}2000 m/s). The significance of these measurements for estimates of heating in shear bands is discussed.

36 MATERIALS SCIENCE↗

Adiabatic shear localization in the CrMnFeCoNi high-entropy alloy

The mechanical behavior of the single phase (fcc) CrMnFeCoNi high-entropy alloy (HEA) is examined in the dynamic regime. Here a series of experiments by dynamic-loading hat-shaped specimens using stopper rings to control the displacement are performed, and the alloy resists adiabatic shear-band formation up to a very large imposed shear strain of ~7. It is proposed that the combination of the excellent strain-hardening ability and moderate thermal-softening effect retard shear localization. Recrystallized ultrafine-grained grains (diameters of 100–300 nm) with twins are revealed inside the shear band. Their formation is explained by the rotational dynamic recrystallization mechanism. The stability of the structure at high strain rates strongly suggests a high ballistic resistance for this class of alloys.

36 MATERIALS SCIENCE↗

Intermetallic particle heterogeneity controls shear localization in high-strength nanostructured Al alloys

The mechanical behavior of two nanocrystalline Al alloys, Al-Mg-Y and Al-Fe-Y, is investigated with in-situ micropillar compression testing. Both alloys were strengthened by a hierarchical microstructure including grain boundary segregation, nanometer-thick amorphous complexions, carbide nanorod precipitates with sizes of a few nanometers, and submicron-scale intermetallic particles. The maximum yield strength of the Al-Mg-Y system is measured to be 950 MPa, exceeding that of the Al-Fe-Y system (680 MPa), primarily due to a combination of more carbide nanorods and more amorphous complexions. Both alloys exhibited yield strengths much higher than those of commercial Al alloys, and therefore have great potential for structural applications. However, some micropillar specimens were observed to plastically soften through shear banding. Post-mortem investigation revealed that intermetallic-free deformation pathways of a few micrometers in length were responsible for this failure. Further characterization showed significant grain growth within the shear band. The coarsened grains maintained the same orientation with each other, pointing to grain boundary mechanisms for plastic flow, specifically grain rotation and/or grain boundary migration. Here, the presence of intermetallic particles makes it difficult for both matrix and intermetallic grains to rotate into the same orientation due to the different lattice parameters and slip systems. Therefore, we are able to conclude that a uniform distribution of intermetallic particles with an average spacing less than the percolation length of shear localization can effectively prevent the maturation of shear bands, offering a design strategy for high-strength nanocrystalline Al alloys with both high strength and stable plastic flow.

36 MATERIALS SCIENCE↗

Benchmark study of a new simplified DFN model for shearing of intersecting fractures and faults

It is challenging to quantitatively predict shearing of intersecting fractures/faults because of dynamic frictional contacts accompanied by possible nonlinear rock deformation. To address such challenges, a new conceptual model—the simplified DFN model—was proposed and validated by Hu et al. 46 to use major paths (MPs) to represent complicated DFNs for calculation of shearing. In this work, we conducted a benchmark study for three examples that involve different levels of complexity of intersecting fractures, and correspondingly different numbers of MPs. The codes and software that were used in the benchmark cover a range of continuum, discontinuum and hybrid numerical methods: NMM (LBNL), FLAC3D (LBNL), GBDEM (KIGAM), FRACOD (DynaFrax), and CASRock (CAS). The general consistency between DFN and MP cases as predicted by all the codes/software demonstrates that major paths can be used to simplify the geometry of DFNs in a wide range of software. Disagreement in results made by some software and potential future improvements are discussed. We show that (1) shearing of one or multiple major fractures can be reduced if there are multiple smaller intersecting fractures in that area, which is a useful basis for understanding and controlling induced seismicity and merits further analysis, and (2) the agreement achieved in the benchmark examples provide confidence that the simplified DFN model is a promising conceptual model that can be used for different types of numerical approaches and software for simplifying the analysis of the shearing of intersecting fractures and faults.

58 GEOSCIENCES↗

A study of adhesive bonding in metal–metal, metal–CFRP, and CFRP–CFRP material combinations under shear deformation: Fracture morphologies and damage mechanisms

Safe design of adhesive joining in multi-materials in engineered structures requires the accumulation of numerous experimental data on the failure behavior of various adhesively-bonded material combinations under different loading conditions. The deep understanding of mechanical performance, fracturing morphologies, and main damage mechanisms is also quintessential for accelerating the development of proper physics-based and multi-scale models for assisting the design. Towards this goal, this work presents a comprehensive characterization of the failure behavior of adhesively-bonded metal–metal, metal–CFRP, and CFRP–CFRP material combinations under global shear deformation via single lap shear testing. Thanks to a synergistic combination of measurement methods by using Digital Imaging Correlation (DIC) and 3D optical profilometry, adhesive features on the adherend after failure were quantified and the main progressive damage mechanisms were identified. The characterization performed in this work provides quantitative data that contributes to a better understanding of shear failure in adhesive bonding across different bi-material combinations. Finally, the obtained results have practical implications, including the potential to enhance adhesive bonding design, identify failure causes in adhesive joints, and develop or validate computational models capable of capturing the observed behavior in various adhesively-bonded materials under global shear deformation.

36 MATERIALS SCIENCE↗

Numerical modeling of injection, stress and permeability enhancement during shear stimulation at the Desert Peak Enhanced Geothermal System

Creation of an Enhanced Geothermal System relies on stimulation of fracture permeability through self-propping shear failure that creates a complex fracture network with high surface area for efficient heat transfer. In 2010, shear stimulation was carried out in well 27-15 at Desert Peak geothermal field, Nevada, by injecting cold water at pressure less than the minimum principal stress. An order-of-magnitude improvement in well injectivity was recorded. In this work, we describe a numerical model that accounts for injection-induced stress changes and permeability enhancement during this stimulation. We use the coupled thermo-hydrological–mechanical simulator FEHM to (i) construct a wellbore model for non-steady bottom-hole temperature and pressure conditions during the injection, and (ii) apply these pressures and temperatures as a source term in a numerical model of the stimulation. A Mohr–Coulomb failure criterion and empirical fracture permeability is developed to describe permeability evolution of the fractured rock. The numerical model is calibrated using laboratory measurements of material properties on representative core samples and wellhead records of injection pressure and mass flow during the shear stimulation. The model captures both the absence of stimulation at low wellhead pressure (WHP ≤1.7 and ≤2.4 MPa) as well as the timing and magnitude of injectivity rise at medium WHP (3.1 MPa). Results indicate that thermoelastic effects near the wellbore and the associated non-local stresses further from the well combine to propagate a failure front away from the injection well. Elevated WHP promotes failure, increases the injection rate, and cools the wellbore; however, as the overpressure drops off with distance, thermal and non-local stresses play an ongoing role in promoting shear failure at increasing distance from the well.

15 GEOTHERMAL ENERGY↗

Mass transport in a highly immiscible alloy on extended shear deformation

Forced mixing to a single phase or supersaturated solid solution (SSS) and its prerequisite microstructure evolution in immiscible systems has been a focus of research for both fundamental science and a variety of applications. Controlling the formation of SSS by shear deformation assisted processing could enable a material design beyond conventional equilibrium microstructure in immiscible systems. Here, a highly immiscible (mixing enthalpy of ~ 20 kJ·mol -1 ) Cu-50 at. % Cr binary alloy was employed to investigate the microstructure evolution and localized tendencies of SSS during severe shear deformation. The present results demonstrate distinctive microstructure refinement process in each phase and how they lead to localized SSS as a function of shear strain. Preferential dynamic recrystallization occurs in the softer Cu phase due to strain localization, leading to substantial grain refinement. The refinement of Cr phase in the top-most layer, however, is enabled by the progressive evolution of grain lamination, splitting, and fragmentation as a function of shear strain. The eventual SSS is found to be strongly dependent on the local environments that affect the dislocation activity, including the level of microstructure refinement, the interfacial orientation relationship, hardness difference, and supposed stability of oxidation. Ab initio simulations comfirm that it is more favorable to oxidize Cr than Cu at incoherent Cu/Cr interfaces which then limits the mass transport on an incoherent boundary. Our results shed light on the underpinning mechanism for non-equilibrium mass transport in immiscible systems upon severe deformation that can be applicable to a variety of processing techniques aimed at producing immiscible alloys with superior mechanical properties.

36 MATERIALS SCIENCE↗

Microstructural evolution in adiabatic shear bands of copper at high strain rates: Electron backscatter diffraction characterization

The microstructural evolution of adiabatic shear bands in annealed copper with different large strains at high strain rates has been investigated by electron backscatter diffraction. The results show that mechanical twinning can occur with minimal contribution to shear localization under dynamic loading. Elongated ultrafine grains with widths of 100-300 nm are observed during the evolution of the adiabatic shear bands. A rotational dynamic recrystallization mechanism is proposed to explain the formation of the elongated ultrafine grains. - Highlights: Black-Right-Pointing-Pointer The microstructural evolution of ASB is studied by electron backscatter diffraction. Black-Right-Pointing-Pointer Twinning can occur in ASB while the contribution to shear localization is slight. Black-Right-Pointing-Pointer Elongated ultrafine grains are observed during the evolution process of ASB. Black-Right-Pointing-Pointer A possible mechanism is proposed to explain the microstructure evolution of ASB.

36 MATERIALS SCIENCE↗

Micromechanical and in situ shear testing of Al–SiC nanolaminate composites in a transmission electron microscope (TEM)

Nanolaminate composites show promise as high strength and toughness materials. Still, due to the limited volume of these materials, micron scale mechanical testing methods must be used to determine the properties of these films. To this end, a novel approach combining a double notch shear testing geometry and compression with a flat punch in a nanoindenter was developed to determine the mechanical properties of these films under shear loading. To further elucidate the failure mechanisms under shear loading, in situ TEM experiments were performed using a double notch geometry cut into the TEM foil. Aluminum layer thicknesses of 50nm and 100nm were used to show the effect of constraint on the deformation. Higher shear strength was observed in the 50 nm sample (690±54 MPa) compared to the 100 nm sample (423±28.7 MPa). Additionally, failure occurred along the Al-SiC interface in the 50 nm sample as opposed to failure within the Al layer in the 100 nm sample.

36 MATERIALS SCIENCE↗

Collisionless instability of thin current sheets in the presence of sheared parallel flows

The first results of an ongoing investigation of the influence of sheared parallel flows on the onset of collisionless magnetic reconnection in thin current sheets are reported. In particular, an exact kinetic equilibrium that incorporates flow with a symmetric profile into the well-known Harris model is proposed and its linear stability is described. The complete linearized Vlasov-Maxwell system is solved using a numerical approach that introduces no approximations regarding the shape of the particle orbits or relative magnitude of the different components of the electromagnetic potentials. Thus accurate results are obtained in a difficult, but practically important limit where the characteristic length scales for the variation of the equilibrium magnetic field and flow are comparable to the ion kinetic length scales. In particular, the dispersion relation for an instability that produces magnetic reconnection is traced as a function of the flow speed V{sub 0} at the center of the sheet, starting with the collisionless tearing mode at V{sub 0}=0. The effects of the sheared flow are shown to qualitatively depend on the thickness of the current sheet. In relatively thick sheets the characteristic features of the dispersion relation depend mostly on the value of the flow shear. In this regime there exist regions of the parameter space where the flow is destabilizing. However, the growth rate of the instability never significantly exceeds that of the collisionless tearing mode and the mode is always stabilized at high enough values of V{sub 0}. When the sheet is thinner than the ion gyroradius in the asymptotic magnetic field, the flow shear introduces strong non-Maxwellian features into the equilibrium distribution function. In this regime, the flow is purely stabilizing for the equilibrium considered. The instability produces magnetic reconnection in all the parameter regimes considered. Finally, the results of the linear analysis are verified using large-scale particle-in-cell simulations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Statistical analysis of the turbulent Reynolds stress and its link to the shear flow generation in a cylindrical laboratory plasma device

The statistical properties of the turbulent Reynolds stress arising from collisional drift turbulence in a magnetized plasma column are studied and a physical picture of turbulent driven shear flow generation is discussed. The Reynolds stress peaks near the maximal density gradient region, and is governed by the turbulence amplitude and cross-phase between the turbulent radial and azimuthal velocity fields. The amplitude probability distribution function (PDF) of the turbulent Reynolds stress is non-Gaussian and positively skewed at the density gradient maximum. The turbulent ion-saturation (Isat) current PDF shows that the region where the bursty Isat events are born coincides with the positively skewed non-Gaussian Reynolds stress PDF, which suggests that the bursts of particle transport appear to be associated with bursts of momentum transport as well. At the shear layer the density fluctuation radial correlation length has a strong minimum ({approx}4-6 mm{approx}0.5C{sub s}/{omega}{sub ci}, where C{sub s} is the ion acoustic speed and {omega}{sub ci} is the ion gyrofrequency), while the azimuthal turbulence correlation length is nearly constant across the shear layer. The results link the behavior of the Reynolds stress, its statistical properties, generation of bursty radially going azimuthal momentum transport events, and the formation of the large-scale shear layer.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Effects of toroidal rotation shear on toroidicity-induced Alfven eigenmodes in the National Spherical Torus Experiment

The effects of a sheared toroidal rotation on the dynamics of bursting toroidicity-induced Alfven eigenmodes are investigated in neutral beam heated plasmas on the National Spherical Torus Experiment (NSTX) [M. Ono et al., Nucl. Fusion 40, 557 (2000)]. The modes have a global character, extending over most of the minor radius. A toroidal rotation shear layer is measured at the location of maximum drive for the modes. Contrary to results from other devices, no clear evidence of decorrelation of the modes by the sheared rotation is found. Instead, experiments with simultaneous neutral beam and radio-frequency auxiliary heating show a strong correlation between the dynamics of the modes and the instability drive. It is argued that kinetic effects involving changes in the mode drive and damping mechanisms other than rotation shear, such as continuum damping, are mostly responsible for the bursting dynamics of the modes on NSTX.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Evolution of symmetric reconnection layer in the presence of parallel shear flow

The development of the structure of symmetric reconnection layer in the presence of a shear flow parallel to the antiparallel magnetic field component is studied by using a set of one-dimensional (1D) magnetohydrodynamic (MHD) equations. The Riemann problem is simulated through a second-order conservative TVD (total variation diminishing) scheme, in conjunction with Roe's averages for the Riemann problem. The simulation results indicate that besides the MHD shocks and expansion waves, there exist some new small-scale structures in the reconnection layer. For the case of zero initial guide magnetic field (i.e., B{sub y0} = 0), a pair of intermediate shock and slow shock (SS) is formed in the presence of the parallel shear flow. The critical velocity of initial shear flow V{sub zc} is just the Alfven velocity in the inflow region. As V{sub z{infinity}} increases to the value larger than V{sub zc}, a new slow expansion wave appears in the position of SS in the case V{sub z{infinity}} < V{sub zc}, and one of the current densities drops to zero. As plasma {beta} increases, the out-flow region is widened. For B{sub y0} {ne} 0, a pair of SSs and an additional pair of time-dependent intermediate shocks (TDISs) are found to be present. Similar to the case of B{sub y0} = 0, there exists a critical velocity of initial shear flow V{sub zc}. The value of V{sub zc} is, however, smaller than the Alfven velocity of the inflow region. As plasma {beta} increases, the velocities of SS and TDIS increase, and the out-flow region is widened. However, the velocity of downstream SS increases even faster, making the distance between SS and TDIS smaller. Consequently, the interaction between SS and TDIS in the case of high plasma {beta} influences the property of direction rotation of magnetic field across TDIS. Thereby, a wedge in the hodogram of tangential magnetic field comes into being. When {beta}{yields}{infinity}, TDISs disappear and the guide magnetic field becomes constant.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

The dynamics of ion with electrostatic waves in a sheared magnetic field

The interaction between an ion and multiple electrostatic waves propagating perpendicularly to an ambient magnetic field with shear is investigated. Based on the Lie transformation method, with the wave amplitude and the magnetic shear both as the perturbation parameters, the analytical formulas for the reduced Hamiltonian is derived and results are compared with numerical calculations of the complete equations of motion for the case of two on-resonance waves and the case of two off-resonance waves, respectively. It is found that the effect of magnetic shear drastically prevents the acceleration of an ion in both cases. This result will help us to understand the behaviors of ions in a magnetic sheared device, such as tokamak.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗