SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Single-event gate rupture (SEGR)in vertical power MOSFETs is induced by charge deposited in the epitaxial region (below the gate oxide) in concert with the weakening of the oxide, both are a result of the ion passage.
Single-event-effect test results for hi-rel total-dose-hardened power MOSFETs are presented in this report. TheSCF9550 from Semicoa and the IRHM57260SE from International Rectifier were tested to NASA test condition/standards and requirements.The IRHM57260SE performed much better when compared to previous testing. These initial results confirm that parts from the Temecula line are marginally comparable to the El Segundo line. The SCF9550 from Semicoa was also tested and represents the initial parts offering from this vendor. Both parts experienced single-event gate rupture (SEGR) and single-event burnout (SEB). All of the SEGR was from gate to drain.
Radiation encountered in space environments can be damaging to microelectronics and potentially cause spacecraft failure. Single event effects (SEE) are a type of radiation effect that occur when an ion strikes a device. Single event gate rupture (SEGR) is a type of SEE that can cause failure in power transistors. Unlike other SEE rates in which a constant linear energy transfer (LET) can be used, SEGR rates sometimes require a non-uniform LET to be used to be accurate. A recent analysis shows that SEGR rates are most easily calculated when the environment is described as a stopping rate per unit volume for each ion species. Stopping rates in silicon for pertinent ions were calculated using the Stopping and Range of Ions in Matter (SRIM) software and CREME-MC software. A reference table was generated and can be used by others to calculate SEGR rates for a candidate device. Additionally, lasers can be used to simulate SEEs, providing more control and information at lower cost than heavy ion testing. The electron/hole pair generation rate from a laser pulse in a semiconductor can be related to the LET of an ion. MATLAB was used to generate a plot to easily make this comparison.
The higher energy content (265 Wh/kg, 725 Wh/L) of the newer cell designs from LG, Panasonic, and Samsung have made them susceptible to side wall ruptures (SWR) during thermal runaway, rather than venting through the intended vent path in the cell header. This is also due to higher reaction kinetics of the electrochemistry, thinner can walls, tight crimp enclosure of the cell header, and inadequate flow rate through the header vent. This effort determined that bottom vents and thicker cell can walls both are necessary for reducing the risk of SWR. Compelling evidence was obtained using novel test methods that included an on-demand internal short circuit device, high speed X-ray videography, and cell thermal runaway calorimetry.
This study was undertaken to examine how well the 0.05 inch/min loading rate typically used to develop allowables for open hole compression strength of carbon/epoxy laminates represents structures that may experience a much lower loading rate (such as civil engineering structures) or a much higher loading rate (such as a rocket interstage at liftoff). The Composite Materials Handbook-17 (CMH-17) suggests developing strength allowables at the coupon level (lowest level of the “building block” approach) and using a rigorous statistical analysis to arrive at a strength allowable upon which the structure is to be further designed at higher levels of the building block pyramid. But do these coupon level tests truly represent meaningful stresses at which the composite in the final structure can withstand considering the effects of loading rate? Open hole compression (OHC) strength was chosen for this study since most structures are designed to some damage tolerance criteria and OHC strength testing is rather simple to perform. A quasi-isotropic lay-up was chosen since this is a very common lay-up sequence. The results show that for structures that experience a very small loading rate (0.0005 in/min) the allowables developed at the standard 0.05 in/min loading rate are higher than what the composite can withstand at this lower loading rate. Conversely, at a high loading rate of 10 in/min the strength values found at the standard test rate of 0.05 in/min are slightly lower and not “in family” using the statistics suggested in CMH-17. These results question if standardized test rates are reliable, at least to the fidelity of being “in family” per CMH-17. Some creep rupture tests were also performed to demonstrate that OHC strength values could be lower than the slowest test speed used in this study (0.0005 in/min).
This document presents the results of a series of studies performed to develop data-driven rupture limit equations and ballistic limit equations for composite overwrapped pressure vessels. These equations can be used to differentiate between impact conditions that would result in only a small hole or crack from those that would cause catastrophic tank failure. This information would be useful in selecting tank materials to avoid catastrophic tank failure in the event of a perforating on-orbit micrometeoroid or orbital debris particle impact.
This memorandum formally documents the completion of the Level 3 milestone M3AT-22IN0604055 titled, “Continue effort to improve Alloy 800H weldment creep rupture performance,” by the transmittal of this deliverable document, entitled, “Issue memo ‘Preliminary assessment of UTP A 2133 Mn as a matching filler metal for Alloy 800H in Section III Division 5 applications.’” The deadline for this milestone is August 27, 2022. This milestone is part of the ART GCR work package AT-22IN060405, “Long-Term Very-High Temperature Reactor (VHTR) Material Qualification – INL.”
Abstract Gas evolution from high‐nickel layered oxide cathodes (>90% Ni) remains a major issue for their practical application. Gaseous species, such as CO 2 , O 2 , and CO, that are evolved at high states of charge (SOC) worsen the overall safety of batteries, as pressure build‐up within the cell may lead to cell rupture. Since these gasses are produced during cathode degradation, tracking the formation of gasses is also important in diagnosing cathode failure. Online electrochemical mass spectrometry (OEMS) is a powerful in situ technique to study gas evolution from the cathode during high‐voltage charge. However, the differences in the OEMS experimental setups between different groups make it challenging to compare results between groups. In this perspective, the various factors that influence gas evolution based on the OEMS results collected in this group are presented. The focus is on the conditions that lead to gas release, with a particular emphasis on reactive oxygen formation and subsequent chemical reactions with the electrolyte. Promising strategies, such as electrolytes, compositional tuning, and surface coatings that are effective at suppressing gas evolution from the cathode are highlighted. Critical insights into mitigating cathode degradation and gas evolution are provided to guide the development of safer, high‐energy batteries.
Abstract Mechanistic studies of substrate insertion into dimeric [(NHC)CuH] 2 (NHC=N‐heterocyclic carbene) complexes with two bridging hydrides have been shown to require dimer dissociation to generate transient, highly reactive (NHC)Cu−H monomers in solution. Using single‐crystal to single‐crystal (SC‐SC) transformations, we discovered a new pathway of stepwise insertion of CO 2 into [(NHC)CuH] 2 without complete dissociation of the dimer. The first CO 2 insertion into dimeric [(IPr*OMe)CuH] 2 (IPr*OMe=N,N′‐bis(2,6‐bis(diphenylmethyl)‐4‐methoxy‐phenyl)imidazole‐2‐ylidene) produced a dicopper formate hydride [(IPr*OMe)Cu] 2 (μ‐1,3‐O 2 CH)(μ‐H). A second CO 2 insertion produced a dicopper bis(formate), [(IPr*OMe)Cu] 2 (μ‐1,3‐O 2 CH)(μ‐1,1‐O 2 CH), containing two different bonding modes of the bridging formate. These dicopper formate complexes are inaccessible from solution reactions since the dicopper core cleanly ruptures to monomeric complexes when dissolved in a solvent.
Abstract The question of when a chemical bond can be said to be broken is of fundamental chemical interest but has not been widely studied. Herein we propose that the maxima of static polarizability along bond dissociation coordinates naturally define cutoff points for bond rupture, as they represent the onset of localization of shared electron density into constituent fragments. Examples of computed polarizability maxima over the course of bond cleavage in main‐group and transition metal compounds are provided, across covalent, dative and charge‐shift bonds. The behavior along reaction paths is also considered. Overall, the static polarizability is found to be a sensitive reporter of electronic structure reorganization associated with bond stretching, and thus can serve as a metric for describing bond cleavage (or diagnose the absence of a chemical bond).
Abstract The continuous rupturing and rebuilding of unstable solid electrolyte interphase (SEI) layer during cycling would block Na + diffusion and induce Na dendrite formation, ultimately limiting the practical application of high‐energy‐density sodium metal batteries. Herein, a hybrid SEI layer containing Li‐species is dexterously constructed on the surface of sodium metal anode. Li‐containing inorganic components (Li 3 N, LiF, and Li 2 CO 3 ) are introduced to stabilize the Na/electrolyte interface and enhance the mechanical and diffusion kinetic properties of the SEI layer, which can reduce the side reactions and gas generation, regulate Na + flux during cycling and promote rapid Na + migration for uniform dendrite‐free Na deposition. As a result, the constructed Na symmetric cells achieve low overpotential and long cycle life of 5900, 1800, and 500 h at current densities of 3, 10, and 30 mA cm −2 , respectively. Furthermore, the full cells paired with the Na₃V₂(PO₄)₃ cathode demonstrate high specific capacity and excellent cycle stability, even at an ultra‐high cathode loading of 39.3 mg cm −2 and a low N/P ratio (negative/positive electrode capacity ratio of 1.21).
Abstract Mechanistic studies of substrate insertion into dimeric [(NHC)CuH] 2 (NHC=N‐heterocyclic carbene) complexes with two bridging hydrides have been shown to require dimer dissociation to generate transient, highly reactive (NHC)Cu−H monomers in solution. Using single‐crystal to single‐crystal (SC‐SC) transformations, we discovered a new pathway of stepwise insertion of CO 2 into [(NHC)CuH] 2 without complete dissociation of the dimer. The first CO 2 insertion into dimeric [(IPr*OMe)CuH] 2 (IPr*OMe=N,N′‐bis(2,6‐bis(diphenylmethyl)‐4‐methoxy‐phenyl)imidazole‐2‐ylidene) produced a dicopper formate hydride [(IPr*OMe)Cu] 2 (μ‐1,3‐O 2 CH)(μ‐H). A second CO 2 insertion produced a dicopper bis(formate), [(IPr*OMe)Cu] 2 (μ‐1,3‐O 2 CH)(μ‐1,1‐O 2 CH), containing two different bonding modes of the bridging formate. These dicopper formate complexes are inaccessible from solution reactions since the dicopper core cleanly ruptures to monomeric complexes when dissolved in a solvent.
Abstract The question of when a chemical bond can be said to be broken is of fundamental chemical interest but has not been widely studied. Herein we propose that the maxima of static polarizability along bond dissociation coordinates naturally define cutoff points for bond rupture, as they represent the onset of localization of shared electron density into constituent fragments. Examples of computed polarizability maxima over the course of bond cleavage in main‐group and transition metal compounds are provided, across covalent, dative and charge‐shift bonds. The behavior along reaction paths is also considered. Overall, the static polarizability is found to be a sensitive reporter of electronic structure reorganization associated with bond stretching, and thus can serve as a metric for describing bond cleavage (or diagnose the absence of a chemical bond).
The continuous rupturing and rebuilding of unstable solid electrolyte interphase (SEI) layer during cycling would block Na + diffusion and induce Na dendrite formation, ultimately limiting the practical application of high-energy-density sodium metal batteries. Herein, a hybrid SEI layer containing Li-species is dexterously constructed on the surface of sodium metal anode. Li-containing inorganic components (Li 3 N, LiF, and Li 2 CO 3 ) are introduced to stabilize the Na/electrolyte interface and enhance the mechanical and diffusion kinetic properties of the SEI layer, which can reduce the side reactions and gas generation, regulate Na + flux during cycling and promote rapid Na + migration for uniform dendrite-free Na deposition. As a result, the constructed Na symmetric cells achieve low overpotential and long cycle life of 5900, 1800, and 500 h at current densities of 3, 10, and 30 mA cm −2 , respectively. Furthermore, the full cells paired with the Na₃V₂(PO₄)₃ cathode demonstrate high specific capacity and excellent cycle stability, even at an ultra-high cathode loading of 39.3 mg cm −2 and a low N/P ratio (negative/positive electrode capacity ratio of 1.21).
Ground-motion simulations generated from physics-based wave propagation models are gaining increasing interest in the engineering community for their potential to inform the performance-based design and assessment of infrastructure residing in active seismic areas. A key prerequisite before the ground-motion simulations can be used with confidence for application in engineering domains is their comprehensive and rigorous investigation and validation. This article provides a four-step methodology and acceptance criteria to assess the reliability of simulated ground motions of not historical events, which includes (1) the selection of a population of real records consistent with the simulated scenarios, (2) the comparison of the distribution of Intensity Measures (IMs) from the simulated records, real records, and Ground-Motion Prediction Equations (GMPEs), (3) the comparison of the distribution of simple proxies for building response, and (4) the comparison of the distribution of Engineering Demand Parameters (EDPs) for a realistic model of a structure. Specific focus is laid on near-field ground motions (<10km) from large earthquakes (M w 7), for which the database of real records for potential use in engineering applications is severely limited. The methodology is demonstrated through comparison of (2490) near-field synthetic records with 5 Hz resolution generated from the Pitarka et al (2019) kinematic rupture model with a population of (38) pulse-like near-field real records from multiple events and, when applicable, with NGA-W2 GMPEs. Lastly, the proposed procedure provides an effective method for informing and advancing the science needed to generate realistic ground-motion simulations, and for building confidence in their use in engineering domains.
Understanding the initiation and arrest of earthquakes is one of the long-standing challenges of seismology. Here we report on direct observations of borehole displacement by a meter-sized shear rupture induced by pressurization of metamorphic rock at 1.5 km depth. We observed the acceleration of sliding, followed by fast co-seismic slip and transient afterslip. Total displacements were about 7, 5.5 and 9.5 micrometers, respectively for the observed pre-slip, co-seismic slip and afterslip. The observed pre-slip lasted about 0.4 seconds. Co-seismic slip was recorded by the 1 kHz displacement recording and a 12-component array of 3-C accelerometers sampled at 100 kHz. The observed afterslip is consistent with analytical models of arrest in a velocity-strengthening region and subsequent stress relaxation. < p >The observed slip vector agrees with the activation of a bedding plane within the phyllite, which is corroborated by relocated seismic events that were observed during the later stages of the injection experiment.
Growing interest in offshore geologic carbon sequestration (GCS) motivates risk assessment of large-scale subsea CO 2 well blowouts or pipeline ruptures. For major leaks of CO 2 from wells or pipelines, significant fluxes of CO 2 may occur from the sea surface depending on water depth. In the context of risk assessment of human health and safety, we have used previously simulated coupled well-reservoir and water column model results as a source term for dense gas dispersion of CO 2 above the sea surface. The models are linked together by one-way coupling, that is, output of one model is used as input to the next model. These first-of-their-kind coupled flow results are applicable to assessing the hazard of CO 2 to people at and downwind of the sea surface location of emission. Hazard is quantified by plotting the downwind dispersion length (DDL), which we define in the study as the distances from the emission source to the point at which the emitted CO 2 has been diluted to 5% and 1.5% in air by volume. Here results suggest that large-scale blowouts in shallow water (10 m) may cause hazardous CO 2 plumes extending on the order of several hundred meters downwind. Details of the modeling show DDL has a maximum for windspeed (at an elevation of 10 m) of approximately 5 m/s, with smaller DDL for both weaker and stronger winds. This is explained by the fact that wind favors transport but also causes dispersion; therefore there is a certain wind speed that maximizes DDL.
Post traumatic osteoarthritis (PTOA) is a form of secondary osteoarthritis (OA) that develops in ~50% of cases of severe articular joint injuries and leads to chronic and progressive degradation of articular cartilage and other joint tissues. PTOA progression can be exacerbated by repeated injury and systemic inflammation. Few studies have examined approaches for blunting or slowing down PTOA progression with emphasis on systemic inflammation; most arthritis studies focused on the immune system have been in the context of rheumatoid arthritis. To examine how the gut microbiome affects systemic inflammation during PTOA development, we used a chronic antibiotic treatment regimen starting at weaning for 6 weeks before anterior cruciate ligament (ACL) rupture in STR/ort mice combined with lipopolysaccharide (LPS)-induced systemic inflammation. STR/ort mice develop spontaneous OA as well as a more severe PTOA phenotype than C57Bl/6J mice. By 6 weeks post injury, histological examination showed a more robust cartilage staining in the antibiotic-treated (AB) STR/ort mice than in the untreated STR/ort controls. Furthermore, we also examined the effects of AB treatment on systemic inflammation and found that the effects of LPS administration before injury are also blunted by AB treatment in STR/ort mice. The AB- or AB+LPS-treated STR/ort injured joints more closely resembled the C57Bl/6J VEH OA phenotypes than the vehicle- or LPS-treated STR/ort, suggesting that antibiotic treatment has the potential to slow disease progression and should be further explored therapeutically as prophylactic post injury.