SEARCH · Engineering Papers

Results for “radar methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

All sources NASA NTRS DOE OSTI

NASA NTRS1987

Shuttle Imaging Radar B (SIR-B) Weddell Sea ice observations - A comparison of SIR-B and scanning multichannel microwave radiometer ice concentrations

Ice concentrations over the Weddell Sea were studied using SIR-B data obtained during the October 1984 mission, with special attention given to the effect of ocean waves on the radar return at the ice edge. Sea ice concentrations were derived from the SIR-B data using two image processing methods: the classification scheme at JPL and the manual classification method at Scott Polar Research Institute (SPRI), England. The SIR ice concentrations were compared with coincident concentrations from the Nimbus-7 SMMR. For concentrations greater than 40 percent, which was the smallest concentration observed jointly by SIR-B and the SMMR, the mean difference between the two data sets for 12 points was 2 percent. A comparison between the JPL and the SPRI SIR-B algorithms showed that the algorithms agree to within 1 percent in the interior ice pack, but the JPL algorithm gives slightly greater concentrations at the ice edge (due to the fact that the algorithm is affected by the wind waves in these areas).

Martin, Seelye↗

NASA NTRS1988

Design considerations for advanced multi-polarisation SAR

System design and verification of an airborne imaging radar (AIR) system are discussed. Issues of importance to multipolarization systems (e.g., mutual coherence and amplitude balance between channels) are emphasized. Methods of detecting and correcting channel imbalances are discussed, and AIR test results are presented.

Klein, J. D.↗

NASA NTRS1991

Probability matched Z-R relations for hurricanes from aircraft observations

Methods are developed to establish the relationship between the equivalent reflectivity factor, Z(e) and rain rate, R, for an airborne radar in a hurricane environment. The PDFs of Z(e) as measured by the radar are matched to those of R as measured by a Knollenberg probe on the same aircraft. The resulting Z(e)-R relation does not depend on an absolute calibration of the radar; it implicitly incorporates all the effects resulting from the way in which the beam averages the 3D reflectivity distribution, and also includes the effects of attenuation on average. Good estimates of the rainfall over a suitable space-time domain can thus be made. The techniques developed apply to any type of storm provided the data are stratified by storm type.

Marks, Frank D., Jr.↗

NASA NTRS2002

Lidar Remote Sensing

The laser radar, or lidar (for light detection and ranging) is an important tool for atmospheric studies. Lidar provides a unique and powerful method for unobtrusively profiling aerosols, wind, water vapor, temperature, and other atmospheric parameters. This brief overview of lidar remote sensing is focused on atmospheric applications involving pulsed lasers. The level of technical detail is aimed at the educated non-lidar expert and references are provided for further investigation of specific topics. The article is divided into three main sections. The first describes atmospheric scattering processes and the physics behind laser-atmosphere interactions. The second section highlights some of the primary lidar applications, with brief descriptions of each measurement capability. The third section describes the practical aspects of lidar operation, including the governing equation and operational considerations.

McGill, Matthew J.↗

NASA NTRS2004

NASA Tech Briefs, November 2004

Topics include: Multifunction Imaging and Spectroscopic Instrument; Position-Finding Instrument Built Around a Magnetometer; Improved Measurement of Dispersion in an Optical Fiber; Probe for Sampling of Interstitial Fluid From Bone; Neuropsychological Testing of Astronauts; Method of Calibration for a Large Cathetometer System; Four-Channel PC/104 MIL-STD-1553 Circuit Board; Improved Method of Locating Defects in Wiring Insulation; Strobe Traffic Lights Warn of Approaching Emergency Vehicles; Improved Timing Scheme for Spaceborne Precipitation Radar; Concept for Multiple-Access Free-Space Laser Communications; Variable Shadow Screens for Imaging Optical Devices; Verifying Diagnostic Software; Initial Processing of Infrared Spectral Data; Activity-Centric Approach to Distributed Programming; Controlling Distributed Planning; New Material for Surface-Enhanced Raman Spectroscopy; Treated Carbon Nanofibers for Storing Energy in Aqueous KOH; Advanced Infant Car Seat Would Increase Highway Safety; Development of Biomorphic Flyers; Second-Generation Six-Limbed Experimental Robot; Miniature Linear Actuator for Small Spacecraft; Process for Making Single-Domain Magnetite Crystals; A New Process for Fabricating Random Silicon Nanotips; Resin-Transfer-Molding of a Tool Face; Improved Phase-Mask Fabrication of Fiber Bragg Gratings; Tool for Insertion of a Fiber-Optic Terminus in a Connector; Nanofluidic Size-Exclusion Chromatograph; Lightweight, Low-CTE Tubes Made From Biaxially Oriented LCPs; Using Redundancy To Reduce Errors in Magnetometer Readings; Compact Instrument for Measuring Profile of a Light Beam; Multilayer Dielectric Transmissive Optical Phase Modulator; Second-Generation Multi-Angle Imaging Spectroradiometer; Real-Time Adaptive Color Segmentation by Neural Networks; Research and Development in Optical Communications; Tests of Multibeam Scintillation Mitigation on Laser Uplinks; and Spaceborne Infrared Atmospheric Sounder.

Source record↗

NASA NTRS2012

Global 3-D Ionospheric Electron Density Reanalysis Based on Multisource Data Assimilation

We report preliminary results of a global 3-D ionospheric electron density reanalysis demonstration study during 2002-2011 based on multisource data assimilation. The monthly global ionospheric electron density reanalysis has been done by assimilating the quiet days ionospheric data into a data assimilation model constructed using the International Reference Ionosphere (IRI) 2007 model and a Kalman filter technique. These data include global navigation satellite system (GNSS) observations of ionospheric total electron content (TEC) from ground-based stations, ionospheric radio occultations by CHAMP, GRACE, COSMIC, SAC-C, Metop-A, and the TerraSAR-X satellites, and Jason-1 and 2 altimeter TEC measurements. The output of the reanalysis are 3-D gridded ionospheric electron densities with temporal and spatial resolutions of 1 h in universal time, 5deg in latitude, 10deg in longitude, and approx.30 km in altitude. The climatological features of the reanalysis results, such as solar activity dependence, seasonal variations, and the global morphology of the ionosphere, agree well with those in the empirical models and observations. The global electron content derived from the international GNSS service global ionospheric maps, the observed electron density profiles from the Poker Flat Incoherent Scatter Radar during 2007-2010, and foF2 observed by the global ionosonde network during 2002-2011 are used to validate the reanalysis method. All comparisons show that the reanalysis have smaller deviations and biases than the IRI-2007 predictions. Especially after April 2006 when the six COSMIC satellites were launched, the reanalysis shows significant improvement over the IRI predictions. The obvious overestimation of the low-latitude ionospheric F region densities by the IRI model during the 23/24 solar minimum is corrected well by the reanalysis. The potential application and improvements of the reanalysis are also discussed.

Xinan Yue↗

NASA NTRS2015

Global Precipitation Measurement Cold Season Precipitation Experiment (GCPEx): For Measurement Sake Let it Snow

As a component of the Earth's hydrologic cycle, and especially at higher latitudes,falling snow creates snow pack accumulation that in turn provides a large proportion of the fresh water resources required by many communities throughout the world. To assess the relationships between remotely sensed snow measurements with in situ measurements, a winter field project, termed the Global Precipitation Measurement (GPM) mission Cold Season Precipitation Experiment (GCPEx), was carried out in the winter of 2011-2012 in Ontario, Canada. Its goal was to provide information on the precipitation microphysics and processes associated with cold season precipitation to support GPM snowfall retrieval algorithms that make use of a dual-frequency precipitation radar and a passive microwave imager on board the GPM core satellite,and radiometers on constellation member satellites. Multi-parameter methods are required to be able to relate changes in the microphysical character of the snow to measureable parameters from which precipitation detection and estimation can be based. The data collection strategy was coordinated, stacked, high-altitude and in-situ cloud aircraft missions with three research aircraft sampling within a broader surface network of five ground sites taking in-situ and volumetric observations. During the field campaign 25 events were identified and classified according to their varied precipitation type, synoptic context, and precipitation amount. Herein, the GCPEx fieldcampaign is described and three illustrative cases detailed.

GCPEx↗

NASA NTRS2016

Optical and Physical Methods for Mapping Flooding with Satellite Imagery

Flood and surface water mapping is becoming increasingly necessary, as extreme flooding events worldwide can damage crop yields and contribute to billions of dollars economic damages as well as social effects including fatalities and destroyed communities (Xaio et al. 2004; Kwak et al. 2015; Mueller et al. 2016).Utilizing earth observing satellite data to map standing water from space is indispensable to flood mapping for disaster response, mitigation, prevention, and warning (McFeeters 1996; Brakenridge and Anderson 2006). Since the early 1970s(Landsat, USGS 2013), researchers have been able to remotely sense surface processes such as extreme flood events to help offset some of these problems. Researchers have demonstrated countless methods and modifications of those methods to help increase knowledge of areas at risk and areas that are flooded using remote sensing data from optical and radar systems, as well as free publically available and costly commercial datasets.

satellite imagery↗

NASA NTRS2022

Measurement of Surface Deformation Related to the December 2018 Mt. Etna Eruption Using Time-Series Interferometry and Magma Modeling for Hazard Zone Mapping

Mount Etna has erupted several times since it was first formed. Recently, Mount Etna began erupting again over 24–27 December 2018. Because it erupts frequently, Mount Etna should be observed on a frequent basis. From June 2018 to October 2019, 34 and 56 interferometric synthetic aperture radar (InSAR) images were acquired from the ascending and descending tracks of the Sentinel-1 satellite, respectively. We employed the Stanford Method for Persistent Scatterers (StaMPS) and a refined small baseline subset (SBAS) InSAR method to produce a surface deformation time-series map. In the time-series analysis, the phase signal remained unaltered with time. The Okada model was then applied to the result to generate a modeled interferogram, and the Q-LavHA program was run to generate a lava flow prediction model. A direct comparison of the results showed that Persistent Scatterers Interferometry (PSI)-StaMPS and the refined SBAS technique were comparable in terms of the displacement pattern, with slightly different velocity values obtained for individual points. In particular, a velocity range of −25 to 21 cm/yr was obtained from PSI-StaMPS, whereas a range of −30 to 25 cm/yr was obtained from the refined SBAS method. Upon computation of the vertical and east-west displacement components based on ascending and descending track data using both methods, deformation velocities of 51.5 and 52.5 cm/yr in the westerly direction on the western flank of Mount Etna were obtained from PSI-StaMPS and the refined SBAS method, respectively, whereas on the eastern flank, deformation toward the east was estimated to occur at a velocity of 50.1 or 54.2 cm/yr, respectively. PSIStaMPS estimated a vertical deformation velocity of −5.3 to 18.3 cm/yr, whereas the refined SBAS method produced a velocity range of approximately −7 to 19 cm/yr. The interferogram obtained via Okada modeling showed two fault sources in the 2018 Mount Etna eruption and a total volume change of approximately 12.39 × 10 6 m 3 . From the modeling results, a lava flow prediction model was generated using the Q-LavHA program. The approaches described in this study can be used by government officials, authorities, and other decision-makers to monitor and assess the risk of volcanic activity in the region.

Suci Ramayanti↗

NASA NTRS1992

Venus topography and kilometer-scale slopes

During the first 8 months of the Magellan mission, the radar altimeter has made some three million measurements of the surface of Venus covering the latitude range from 85 deg N to 80 deg S. Methods involving range correlation, Doppler filtering, multiburst summation, and range migration are used to focus the observations and to achieve high surface resolution. Results are presented as maps of the global distribution of topography, meter-scale roughness, and power reflection coefficient. The results are similar to those reported in previous experiments (surface heights exhibit a unimodal distribution with more than 80 percent of the surface lying within 1 km of the 6051.84-km mean radius) but the higher resolution of the Magellan altimeter has disclosed several surprisingly steep features, e.g., the southwest face of the Maxwell Montes, the southern face of the Danu Montes, and the chasmata to the east of Thetis Regio, where average kilometer-scale slopes of greater than 30 deg are not uncommon. This conclusion is corroborated by close inspection of synthetic aperture radar imagery.

Ford, Peter G.↗

NASA NTRS1979

Mapping of sea ice and measurement of its drift using aircraft synthetic aperture radar images

Side-looking radar images of Arctic sea ice were obtained as part of the Arctic Ice Dynamics Joint Experiment. Repetitive coverages of a test site in the Arctic were used to measure sea ice drift, employing single images and blocks of overlapping radar image strips; the images were used in conjunction with data from the aircraft inertial navigation and altimeter. Also, independently measured, accurate positions of a number of ground control points were available. Initial tests of the method were carried out with repeated coverages of a land area on the Alaska coast (Prudhoe). Absolute accuracies achieved were essentially limited by the accuracy of the inertial navigation data. Errors of drift measurements were found to be about + or - 2.5 km. Relative accuracy is higher; its limits are set by the radar image geometry and the definition of identical features in sequential images. The drift of adjacent ice features with respect to one another could be determined with errors of less than + or - 0.2 km.

Leberl, F.↗

NASA NTRS1979

Evaluation of SLAR and thematic mapper MSS data for forest cover mapping using computer-aided analysis techniques

A literature review on radar and spectral band information was conducted and a NC-130 mission was flown carrying the NS001 scanner system which basically corresponds to the channel configuration of the proposed thematic mapper. Aerial photography and other reference data were obtained for the study site, an area approximately 290 sq miles in north central South Carolina. A cover type map was prepared and methods were devised for reformatting and geometrically correcting MSS CRT data. Arrangements were made to obtain LANDSAT data for dates approximating the NC-130 mission. Because of the waveband employed to obtain SEASAT radar data, it was decided to determine if X-band (2.40 cm to 3.75 cm wavelength) imagery is available.

Hoffer, R. M.↗

NASA NTRS2007

Ice Cloud Properties in Ice-Over-Water Cloud Systems Using TRMM VIRS and TMI Data

A multi-layered cloud retrieval system (MCRS) is updated and used to estimate ice water path in maritime ice-over-water clouds using Visible and Infrared Scanner (VIRS) and TRMM Microwave Imager (TMI) measurements from the Tropical Rainfall Measuring Mission spacecraft between January and August 1998. Lookup tables of top-of-atmosphere 0.65- m reflectance are developed for ice-over-water cloud systems using radiative transfer calculations with various combinations of ice-over-water cloud layers. The liquid and ice water paths, LWP and IWP, respectively, are determined with the MCRS using these lookup tables with a combination of microwave (MW), visible (VIS), and infrared (IR) data. LWP, determined directly from the TMI MW data, is used to define the lower-level cloud properties to select the proper lookup table. The properties of the upper-level ice clouds, such as optical depth and effective size, are then derived using the Visible Infrared Solar-infrared Split-window Technique (VISST), which matches the VIRS IR, 3.9- m, and VIS data to the multilayer-cloud lookup table reflectances and a set of emittance parameterizations. Initial comparisons with surface-based radar retrievals suggest that this enhanced MCRS can significantly improve the accuracy and decrease the IWP in overlapped clouds by 42% and 13% compared to using the single-layer VISST and an earlier simplified MW-VIS-IR (MVI) differencing method, respectively, for ice-over-water cloud systems. The tropical distribution of ice-over-water clouds is the same as derived earlier from combined TMI and VIRS data, but the new values of IWP and optical depth are slightly larger than the older MVI values, and exceed those of single-layered layered clouds by 7% and 11%, respectively. The mean IWP from the MCRS is 8-14% greater than that retrieved from radar retrievals of overlapped clouds over two surface sites and the standard deviations of the differences are similar to those for single-layered clouds. Examples of a method for applying the MCRS over land without microwave data yield similar differences with the surface retrievals. By combining the MCRS with other techniques that focus primarily on optically thin cirrus over low water clouds, it will be possible to more fully assess the IWP in all conditions over ocean except for precipitating systems.

Minnis, Patrick↗

NASA NTRS2012

Achieving Accuracy Requirements for Forest Biomass Mapping: A Spaceborne Data Fusion Method for Estimating Forest Biomass and Lidar Sampling Error

The synergistic use of active and passive remote sensing (i.e., data fusion) demonstrates the ability of spaceborne light detection and ranging (LiDAR), synthetic aperture radar (SAR) and multispectral imagery for achieving the accuracy requirements of a global forest biomass mapping mission (+/-20 Mg/ha or 20%, the greater of the two, for at least 80% of grid cells). A data fusion approach also provides a means to extend 3D information from discrete spaceborne LiDAR measurements of forest structure across scales much larger than that of the LiDAR footprint. For estimating biomass, these measurements mix a number of errors including those associated with LiDAR footprint sampling over regional-global extents. A general framework for mapping above ground live forest biomass density (AGB) with a data fusion approach is presented and verified using data from NASA field campaigns near Howland, ME, USA, to assess AGB and LiDAR sampling errors across a regionally representative landscape. We combined SAR and Landsat-derived optical (passive optical) image data to identify contiguous areas (>0.5 ha) that are relatively homogenous in remote sensing metrics (forest patches). We used this image-derived data with simulated spaceborne LiDAR derived from orbit and cloud cover simulations and airborne data from NASA's Laser Vegetation Imaging Sensor (LVIS) to compute AGB and estimate LiDAR sampling error for forest patches and 100 m, 250 m, 500 m, and 1 km grid cells. At both the patch and grid scales, we evaluated differences in AGB estimation and sampling error from the combined use of LiDAR with both SAR and passive optical and with either SAR or passive optical alone. First, this data fusion approach demonstrates that incorporating forest patches into the AGB mapping framework can provide sub-grid forest information for coarser grid-level AGB reporting. Second, a data fusion approach for estimating AGB using simulated spaceborne LiDAR with SAR and passive optical image combinations reduced forest AGB sampling errors 12%-38% from those where LiDAR is used with SAR or passive optical alone. In absolute terms, sampling errors were reduced from 14-40 Mg/ha to 11-28 Mg/ha across all grid scales and prediction methods, where minimum sampling errors were 11, 15, 18, and 22 Mg/ha for 1 km, 500 m, 250 m, and 100 m grid scales, respectively. Third, spaceborne global scale accuracy requirements were achieved whereby at least 80% of the grid cells at 100 m, 250 m, 500 m, and 1 km grid levels met AGB accuracy requirements using a combination of passive optical and SAR along with machine learning methods to predict vegetation structure metrics for forested areas without LiDAR samples. Finally, using either passive optical or SAR, accuracy requirements were met at the 500 m and 250 m grid level, respectively..

LiDAR↗

NASA NTRS1993

Discrete range clustering using Monte Carlo methods

For automatic obstacle avoidance guidance during rotorcraft low altitude flight, a reliable model of the nearby environment is needed. Such a model may be constructed by applying surface fitting techniques to the dense range map obtained by active sensing using radars. However, for covertness, passive sensing techniques using electro-optic sensors are desirable. As opposed to the dense range map obtained via active sensing, passive sensing algorithms produce reliable range at sparse locations, and therefore, surface fitting techniques to fill the gaps in the range measurement are not directly applicable. Both for automatic guidance and as a display for aiding the pilot, these discrete ranges need to be grouped into sets which correspond to objects in the nearby environment. The focus of this paper is on using Monte Carlo methods for clustering range points into meaningful groups. One of the aims of the paper is to explore whether simulated annealing methods offer significant advantage over the basic Monte Carlo method for this class of problems. We compare three different approaches and present application results of these algorithms to a laboratory image sequence and a helicopter flight sequence.

Chatterji, G. B.↗

NASA NTRSDate not supplied

Quantifying Tropopause-Overshooting Volume from Satellite and Radar Observations During the DCOTSS 2021 and 2022 Campaigns

Tropopause-overshooting cloud locations, their volume, and the percentage of anvil cloud occupied by overshooting were quantified from state-of-the-art merged NEXRAD radar and GOES-16/17 satellite products during the 2021 and 2022 Dynamics and Chemistry of the Summer Stratosphere (DCOTSS) study periods. A novel method for defining and tracking large individual storms or storm outbreak objects in space and time was presented, which enabled improved understanding of the complex feature-specific biases among GOES- and GridRad-derived overshooting metrics. GOES overshooting cloud top height was estimated using a stratospheric lapse rate approach informed by GOES visible and IR measurements of shadows from OTs and calibrated based on previously observed maximum GridRad overshooting distribution. Total overshooting volumes derived over CONUS are higher for GOES than GridRad for both years, especially during 2021. Over all storm outbreak objects with observed overshooting, GOES observed higher overshooting percentages while GridRad observed relatively higher overshooting magnitudes. The greater spatial coverage of GOES overshooting, especially noticeable during the mature and dissipation stages of outbreaks due to inherent limitations of infrared satellite data which make it difficult to differentiate cold, high-altitude outflow from true updraft cores, outweighed differences in magnitude to yield higher GOES volume. Individual events, however, revealed that the higher overshooting magnitudes observed by GridRad produce higher overshooting volumes at times. Four-dimensional trajectories of tropopause-overshooting air parcels were compared 5 days after overshooting occurred to depict the envelope of convectively impacted air in the stratosphere. The generally good agreement in parcel plume area initiated from GOES and GridRad overshooting detections suggests that geostationary satellite data can be used to estimate where and how often overshooting impacts stratospheric composition in regions without a ground-based weather radar network to estimate climate impacts of overshooting convection.

Kristopher Bedka↗

NASA NTRS2013

NASA Tech Briefs, July 2013

Dielectrophoresis-Based Particle Sensor Using Nanoelectrode Arrays; Multi-Dimensional Damage Detection for Surfaces and Structures; ULTRA: Underwater Localization for Transit and Reconnaissance Autonomy; Autonomous Cryogenic Leak Detector for Improving Launch Site Operations; Submillimeter Planetary Atmospheric Chemistry Exploration Sounder; Method for Reduction of Silver Biocide Plating on Metal Surfaces; Silicon Micromachined Microlens Array for THz Antennas; Forward-Looking IED Detector Ground Penetrating Radar; Fully Printed, Flexible, Phased Array Antenna for Lunar Surface Communication, Battery Charge Equalizer with Transformer Array; An Efficient, Highly Flexible Multi-Channel Digital Downconverter Architecture; Dimmable Electronic Ballast for a Gas Discharge Lamp; Conductive Carbon Nanotube Inks for Use with Desktop Inkjet Printing Technology; Enhanced Schapery Theory Software Development for Modeling Failure of Fiber-Reinforced Laminates; High-Performance, Low-Temperature-Operating, Long-Lifetime Aerospace Lubricants; Carbon Nanotube Microarrays Grown on Nanoflake Substrates; Differential Muon Tomography to Continuously Monitor Changes in the Composition of Subsurface Fluids; Microgravity Drill and Anchor System; 20 Granular Media-Based Tunable Passive Vibration Suppressor; 21 Miga Aero Actuator and 2D Machined Mechanical Binary Latch; Micro-XRF for In Situ Geological Exploration of Other Planets; Hydrogen-Enhanced Lunar Oxygen Extraction and Storage Using Only Solar Power; Uplift of Ionospheric Oxygen Ions During Extreme Magnetic Storms; Miniaturized, High-Speed, Modulated X-Ray Source; Hollow-Fiber Spacesuit Water Membrane Evaporator 25 High-Power Single-Mode 2.65-micrometers InGaAsSb/AlInGaAsSb Diode Lasers; Optical Device for Converting a Laser Beam Into Two Co-aligned but Oppositely Directed Beams; A Hybrid Fiber/Solid-State Regenerative Amplifier with Tunable Pulse Widths for Satellite Laser Ranging; X-Ray Diffractive Optics; SynGenics Optimization System (SynOptSys); 29 CFD Script for Rapid TPS Damage Assessment; radEq Add-On Module for CFD Solver Loci-CHEM; Science Opportunity Analyzer (SOA) Version 8; 30 Autonomous Byte Stream Randomizer; Distributed Engine Control Empirical/Analytical Verification Tools; Dynamic Server-Based KML Code Generator Method for Level-of-Detail Traversal of Geospatial Data; Automated Planning of Science Products Based on Nadir Overflights and Alerts for Onboard and Ground Processing; Linked Autonomous Interplanetary Satellite Orbit Navigation; Risk-Constrained Dynamic Programming for Optimal Mars Entry, Descent, and Landing; Scheduling Operations for Massive Heterogeneous Clusters; Deepak Condenser Model (DeCoM); Flight Software Math Library; Recirculating 1-K-Pot for Pulse-Tube Cryostats; 35 Method for Processing Lunar Regolith Using Microwaves; Wells for In Situ Extraction of Volatiles from Regolith (WIEVR); and Estimating the Backup Reaction Wheel Orientation Using Reaction Wheel Spin Rates Flight Telemetry from a Spacecraft.

Source record↗

NASA NTRS1985

Application of infrared radiometers for airborne detection of clear air turbulence and low level wind shear, airborne infrared low level wind shear detection test

The feasibility of infrared optical techniques for the advance detection and avoidance of low level wind shear (LLWS) or low altitude wind shear hazardous to aircraft operations was investigated. A primary feasibility research effort was conducted with infrared detectors and instrumentation aboard the NASA Ames Research Center Learjet. The main field effort was flown on the NASA-Ames Dryden B57B aircraft. The original approach visualized a forward-looking, infrared transmitting (KRS-5) window through which signals would reach the detector. The present concept of a one inch diameter light pipe with a 45 deg angled mirror enables a much simpler installation virtually anywhere on the aircraft coupled with the possibility of horizontal scanning via rotation of the forward directed mirror. Present infrared detectors and filters would certainly permit ranging and horizontal scanning in a variety of methods. CRT display technology could provide a contoured picture with possible shear intensity levels from the infrared detection system on the weather radar or a small adjunct display. This procedure shoud be further developed and pilot evaluated in a light aircraft such as a Cessna 207 or equivalent.

Kuhn, P. M.↗