Results for “protective layer” — Page 41

NASA NTRS1993

Advanced Small Rocket Chambers. Basic Program and Option 2: Fundamental Processes and Material Evaluation

Propellants, chamber materials, and processes for fabrication of small high performance radiation cooled liquid rocket engines were evaluated to determine candidates for eventual demonstration in flight-type thrusters. Both storable and cryogenic propellant systems were considered. The storable propellant systems chosen for further study were nitrogen tetroxide oxidizer with either hydrazine or monomethylhydrazine as fuel. The cryogenic propellants chosen were oxygen with either hydrogen or methane as fuel. Chamber material candidates were chemical vapor deposition (CVD) rhenium protected from oxidation by CVD iridium for the chamber hot section, and film cooled wrought platinum-rhodium or regeneratively cooled stainless steel for the front end section exposed to partially reacted propellants. Laser diagnostics of the combustion products near the hot chamber surface and measurements at the surface layer were performed in a collaborative program at Sandia National Laboratories, Livermore, CA. The Material Sample Test Apparatus, a laboratory system to simulate the combustion environment in terms of gas and material temperature, composition, and pressure up to 6 Atm, was developed for these studies. Rocket engine simulator studies were conducted to evaluate the materials under simulated combustor flow conditions, in the diagnostic test chamber. These tests used the exhaust species measurement system, a device developed to monitor optically species composition and concentration in the chamber and exhaust by emission and absorption measurements.

Jassowski, Donald M.↗

NASA NTRS2003

Volatile Cycling and Layering on Mars: Observations, Theory and Modeling

With the release of Mars Odyssey Gamma Ray Spectrometer (GRS) results, which indicate the presence of vast reservoirs of near-surface ice in the martian polar regions, we are presented with an exquisite dilemma. These deposits, which are present as far down as 60 deg. latitude in both hemispheres, are consistent with the suggestion of thermal models that ice will be best protected in these extended regions during periods of higher obliquity. However, the current paradigm regarding the placement of these deposits, i.e., diffusive deposition of water vapor, appears to be inconsistent with the large volume mixing ratios (approx. 70%) inferred from the GRS data. This apparent conflict argues that diffusion alone cannot be the primary mechanism for the creation of these reservoirs, and that an alternate, large-scale process should be considered.

M A Mischna↗

NASA NTRS2017

Flame Retardant Fibers for Human Space Exploration - Past, Present, and Future

The National Aeronautics and Space Administration (NASA) has led in the development of unique flame retardant fibers for human spaceflight since the beginning of the Apollo program. After the Apollo 1 fire which killed Command Pilot Virgil I 'Gus' Grissom, Senior Pilot Edward H. White II, and Pilot Roger B. Chaffee from cardiac arrest on January 27, 1967, the accident investigators found severe third degree burns and melted spacesuits on the astronauts bodies. NASA immediately initiated an extensive research program aimed at developing flame retardant and flame resistant fibers for the enriched oxygen atmosphere of the Apollo crew cabin. Fibers are flame retardant when they have been modified by chemical and thermal treatments. Fibers are flame resistant when they are made of inherently flame resistant materials (i.e. glass, ceramic, highly aromatic polymers). Immediately after this tragic accident, NASA funded extensive research in specifically developing flame retardant fibers and fabrics. The early developmental efforts for human spaceflight were for the outer layer of the Apollo spacesuit. It was imperative that non-flammable fabrics be used in a 100% oxygen environment. Owens-Corning thus developed the Beta fiber that was immediately used in the Apollo program and later in the Space Shuttle program. Aside from the urgent need for protective fabrics for the spacesuit, NASA also needed flame retardant fabrics for both clothing and equipment inside the spacecraft. From the mid-1960s to the early 1980's, NASA contracted with many companies to develop inherently flame retardant fibers and flame retardant finishes for existing fibers. Fluorocarbons and aromatic polyamides were the polymers of great interest for the development of new inherently flame retardant fibers for enriched oxygen environments. These enriched environments varied for different space programs. For example, the Apollo program requirements were for materials that would not support combustion in a 70%/30% oxygen/nitrogen environment at 6.3 pounds per square inch (psi). The Skylab program flammability requirements were set at 80%/20% oxygen/nitrogen ratios at 5 psi. While many fibers produced under several NASA contracts were never used, a few have become commercial products. The intent of this paper is to present the developmental history of some of these new or modified textile fibers. These developmental efforts are presented at various levels of details depending on the source of the historical records.

Orndoff, Evelyne↗

NASA NTRSDate not supplied

Next Steps: Laying the Groundwork for Bundle Protocol v7

Delay/Disruption Tolerant Networking (DTN) is a networking model and protocol suite that extends the terrestrial internet to the challenging communication environments of space. These environments are typically subject to frequent disruptions, which can cause delays or errors. DTN protects data transmission by wrapping data into bundles (similar to Internet Protocol packets), storing them until a connection can be established between two nodes (similar to terrestrial routers or computers), and forwarding them to their destinations. Bundle Protocol (BP) is responsible for generating those bundles and creates the transport layer of DTN, much like how Transmission Control Protocol (TCP) and User Datagram Protocol (UDP) create the transport layer of the Internet Protocol. BPv6 is the current, accepted version of the Bundle Protocol standard. However, recent missions and test implementations have revealed missing components and areas for improvement in the standard. Using lessons learned from NASA missions and gathering inspiration from the Internet Protocol, BPv7 is intended to be a more robust Bundle Protocol that improves upon its predecessor and increases the technology readiness level of the DTN architecture. The DTN Standard Interface Design team, a sub-team of the DTN Infusion Project at the Goddard Space Flight Center, worked to create a dictionary of terms for bundle components and functional decomposition of the protocol. These efforts aided in the standardization of BP interfaces, something missing from BPv6, and supported parallel network management and configuration work. This standardization will ultimately contribute to LunaNet (a lunar communications and navigation architecture that will bring networking, positioning, navigation, timing and science services to the Moon), the Solar System Internet (SSI), and expand crewed and uncrewed space exploration opportunities.

DTN↗

NASA NTRSDate not supplied

Next Steps: Laying the Groundwork for Bundle Protocol v7

Delay/Disruption Tolerant Networking (DTN) is a networking model and protocol suite that extends the terrestrial internet to the challenging communication environments of space. These environments are typically subject to frequent disruptions, which can cause delays or errors. DTN protects data transmission by wrapping data into bundles (similar to Internet Protocol packets), storing them until a connection can be established between two nodes (similar to terrestrial routers or computers), and forwarding them to their destinations. Bundle Protocol (BP) is responsible for generating those bundles and creates the transport layer of DTN, much like how Transmission Control Protocol (TCP) and User Datagram Protocol (UDP) create the transport layer of the Internet Protocol. BPv6 is the current, accepted version of the Bundle Protocol standard. However, recent missions and test implementations have revealed missing components and areas for improvement in the standard. Using lessons learned from NASA missions and gathering inspiration from the Internet Protocol, BPv7 is intended to be a more robust Bundle Protocol that improves upon its predecessor and increases the technology readiness level of the DTN architecture. The DTN Standard Interface Design team, a sub-team of the DTN Infusion Project at the Goddard Space Flight Center, worked to create a dictionary of terms for bundle components and functional decomposition of the protocol. These efforts aided in the standardization of BP interfaces, something missing from BPv6, and supported parallel network management and configuration work. This standardization will ultimately contribute to LunaNet (a lunar communications and navigation architecture that will bring networking, positioning, navigation, timing and science services to the Moon), the Solar System Internet (SSI), and expand crewed and uncrewed space exploration opportunities.

dtn↗

NASA NTRS1981

Adjustable high emittance gap filler

A flexible, adjustable refractory filler is disclosed for filling gaps between ceramic tiles forming the heat shield of a space shuttle vehicle, to protect its aluminum skin during atmospheric reentry. The easily installed and replaced filler consists essentially of a strip of ceramic cloth coated, at least along both its longitudinal edges with a room temperature vulcanizable silicone rubber compound with a high emittance colored pigment. The filler may have one or more layers as the gap width requires. Preferred materials are basket weave aluminoborosilicate cloth, and a rubber compounded with silicon tetraboride as the emittance agent and finely divided borosilicate glass containing about 7.5% B2O3 as high temperature binder. The filler cloth strip or tape is cut to proper width and length, inserted into the gap, and fastened with previously applied drops of silicone rubber adhesive.

Leiser, D. B.↗

NASA NTRS1996

Atomic Oxygen Removes Varnish And Lacquer From Old Paintings

Dry and relatively nondestructive plasma process found effective in removing protective coats from old paintings. Process generates monatomic oxygen, which reacts with varnish, lacquer, polyurethane, acrylic, and other organic coating materials; reactions produce mostly carbon monoxide and water vapor, then simply pumped away by vacuum system in which plasma generated. Does not attack oxide-based pigments in underlying paint layers, and brush-stroke marks remain undisturbed.

Rutledge, Sharon K.↗

NASA NTRSDate not supplied

Material Response Modeling of Ablative Thermal Protection Systems using PATO

Developing thermal protection systems (TPS) for future space vehicles involves an extensive design and test cycle. A key component of the cycle is determining margins for a safe design that rely on confidence in the performance of the TPS. Predicting the complicated multiphysics phenomena that occur during atmospheric entry requires high-fidelity modeling tools. To this end, the Porous-material Analysis Toolbox based on OpenFOAM (PATO) has been developed. PATO is an open-source software for computing material response of reactive porous materials submitted to high-temperature environments. Recent applications of PATO include computation of the full heatshield 3D material response from the Mars Science Laboratory atmospheric entry and ablation during arc jet testing. Current efforts are underway to loosely couple PATO with other discipline specialized codes including hypersonic computational fluid dynamics (CFD) to assess the effects of pyrolysis-gas blowing into the boundary layer and computational solid mechanics to address modeling of mechanical erosion. Surface phenomena modeling capabilities to address the effects of silicone-based coatings applied to the TPS during flight preparation are also being added.

Thermal Protection Systems↗

NASA NTRSDate not supplied

Material Response Modeling of Ablative Thermal Protection Systems using PATO

Developing thermal protection systems (TPS) for future space vehicles involves an extensive design and test cycle. A key component of the cycle is determining margins for a safe design that rely on confidence in the performance of the TPS. Predicting the complicated multiphysics phenomena that occur during atmospheric entry requires high-fidelity modeling tools. To this end, the Porous-material Analysis Toolbox based on OpenFOAM (PATO) has been developed. PATO is an open-source software for computing material response of reactive porous materials submitted to high-temperature environments. Recent applications of PATO include computation of the full heatshield 3D material response from the Mars Science Laboratory atmospheric entry and ablation during arc jet testing. Current efforts are underway to loosely couple PATO with other discipline specialized codes including hypersonic computational fluid dynamics (CFD) to assess the effects of pyrolysis-gas blowing into the boundary layer and computational solid mechanics to address modeling of mechanical erosion. Surface phenomena modeling capabilities to address the effects of silicone-based coatings applied to the TPS during flight preparation are also being added.

Thermal Protection Systems↗

NASA NTRS1989

Large solar flare radiation shielding requirements for manned interplanetary missions

Estimates are given for the radiation shielding thicknesses required to protect astronauts on interplanetary missions from the effects of large solar flares, on the basis of the integral proton fluences for several past solar particle events. NASA-Langley's nucleon transport deterministic computer code, BRYNTRN, is used to transport primary protons and secondary protons and neutrons through any number of layers of target material of arbitrary thickness and composition. The results of each flare are presented as estimates of dose equivalents to the skin, eyes, and blood-forming organs behind various thicknesses of aluminum shielding.

Townsend, Lawrence W.↗

NASA NTRS1978

Evaluations of candidate encapsulation designs and materials for low-cost silicon photovoltaic arrays

Three encapsulation designs for silicon photovoltaic arrays based on cells with silk-screened Ag metallization have been evaluated: transparent polymeric coatings over cells laminated between two films or sheets of polymeric materials; cells adhesively bonded to a glass cover with a polymer pottant and a glass or other substrate component. Silicone and acrylic coatings were assessed, together with acrylic sheet, 0.635 mm fiberglass-reinforced polyester sheet, 0.102 mm polycarbonate/acrylic dual-layer film, 0.127 mm fluorocarbon film, soda-lime glass, borosilicate glass, low-iron glass, and several adhesives. The encapsulation materials were characterized by light transmittance measurements, determination of moisture barrier properties and bond strengths, and by the performance of cells before and after encapsulation. Silicon and acrylic coatings provided inadequate protection. Acrylic and fluorocarbon films displayed good weatherability and acceptable optical transmittance. Borosilicate, low-iron and soda-lime-float glasses were found to be acceptable candidate encapsulants for most environments.

Gaines, G. B.↗

NASA NTRS1998

Electro-Optical Effects in Thin Organic Films

Meta-nitroaniline (mNA) and 2-cyclo-octylamino-5-nitropyridine (COANP) single crystals were grown between two transparent fused quartz plates on which indium-tin-oxide layers were deposited. Both linear and quadratic electro-optic effects of the crystals were examined by an ac modulation method. The figures of merit for mNA and COANP are estimated to be 3.2(10-12 m/V and 4.2(10-12 m/V, respectively. It was found that the crystals were under good protection of the cells and the figure of merits of the crystals did not decrease with time. It is believed that the method adopted in the paper is applicable to electro-optic cell fabrication with other compounds if those crystals growth from melt is feasible. It is suggested that the electro-optic cells have potential fortune because of their durability and relative easy manipulation processes of crystal growth.

Leyderman, Alexander↗

NASA NTRS2007

The Dynamics of Shock Dispersion and Interactions in Supersonic Freestreams with Counterflowing Jets

An active flow control concept using counterflowing jets to significantly modify the external flowfields and strongly weaken or disperse the shock-waves of supersonic and hypersonic vehicles to reduce the aerothermal loads and wave drag was investigated. Experiments were conducted in a trisonic blow-down wind-tunnel, complemented by pre-test computational fluid dynamics (CFD) analysis of a 2.6% scale model of Apollo capsule, with and without counterflowing jets, in Mach 3.48 and 4.0 freestreams, to assess the potential aerothermal and aerodynamic benefits of this concept. The model was instrumented with heat flux gauges, thermocouples and pressure taps, and employed five counterflowing jet nozzles (three sonic and other two supersonic with design Mach numbers of 2.44 and 2.94) and nozzle exit diameters ranging from 0.25 to 0.5 inch. Schlieren data show that at low jet flow rates of 0.05 and 0.1lb(sub m)/sec, the interactions result in a long penetration mode (LPM) jet, while the short penetration mode (SPM) jet is observed at flow rates greater than 0.1 lb(sub m)/sec., consistent with the pre-test CFD predictions. For the LPM, the jet appears to be nearly fully-expanded, resulting in a very unsteady and oscillatory flow structure in which the bow shock becomes highly dispersed such that it is no longer discernable. Higher speed camera Schlieren data reveal the shock to be dispersed into striations of compression waves, which suddenly coalesce to a weaker bow shock with a larger standoff distance as the flow rate reached a critical value. The pronounced shock dispersion could significantly impact the aerodynamic performance (L/D) and heat flux reduction of spacecraft in atmospheric entry and re-entry, and could also attenuate the entropy layer in hypersonic blunt body flows. For heat transfer, the results show significant reduction in heat flux, even giving negative heat flux for some of the SPM interactions, indicating that the flow wetting the model is cooling, instead of heating the model, which could significantly impact the requirements and design of thermal protection system. These findings strongly suggest that the application of counterflowing jets as active flow control could have strong impact on supersonic and hypersonic vehicle design and performance.

Daso, Endwell O.↗

NASA NTRS2004

NASA Tech Briefs, February 2004

Topics include: Simulation Testing of Embedded Flight Software; Improved Indentation Test for Measuring Nonlinear Elasticity; Ultraviolet-Absorption Spectroscopic Biofilm Monitor; Electronic Tongue for Quantitation of Contaminants in Water; Radar for Measuring Soil Moisture Under Vegetation; Modular Wireless Data-Acquisition and Control System; Microwave System for Detecting Ice on Aircraft; Routing Algorithm Exploits Spatial Relations; Two-Finger EKG Method of Detecting Evasive Responses; Updated System-Availability and Resource-Allocation Program; Routines for Computing Pressure Drops in Venturis; Software for Fault-Tolerant Matrix Multiplication; Reproducible Growth of High-Quality Cubic-SiC Layers; Nonlinear Thermoelastic Model for SMAs and SMA Hybrid Composites; Liquid-Crystal Thermosets, a New Generation of High-Performance Liquid-Crystal Polymers; Formulations for Stronger Solid Oxide Fuel-Cell Electrolytes; Simulation of Hazards and Poses for a Rocker-Bogie Rover; Autonomous Formation Flight; Expandable Purge Chambers Would Protect Cryogenic Fittings; Wavy-Planform Helicopter Blades Make Less Noise; Miniature Robotic Spacecraft for Inspecting Other Spacecraft; Miniature Ring-Shaped Peristaltic Pump; Compact Plasma Accelerator; Improved Electrohydraulic Linear Actuators; A Software Architecture for Semiautonomous Robot Control; Fabrication of Channels for Nanobiotechnological Devices; Improved Thin, Flexible Heat Pipes; Miniature Radioisotope Thermoelectric Power Cubes; Permanent Sequestration of Emitted Gases in the Form of Clathrate Hydrates; Electrochemical, H2O2-Boosted Catalytic Oxidation System; Electrokinetic In Situ Treatment of Metal-Contaminated Soil; Pumping Liquid Oxygen by Use of Pulsed Magnetic Fields; Magnetocaloric Pumping of Liquid Oxygen; Tailoring Ion-Thruster Grid Apertures for Greater Efficiency; and Lidar for Guidance of a Spacecraft or Exploratory Robot.

Source record↗

NASA NTRS1980

Photoelastic tests on models of thermal protection system for space shuttle orbiter

The thermal protection system (TPS) of the space shuttle orbiter vehicle, consisting of ceramic tile/adhesive/strain isolator pad/adhesive/aluminum substructure, was modeled photoelasticity. A highly sensitive photoelastic material was used in the models to show the nature of the stress-transfer between the strain isolation pad (SIP) and the ceramic tile through the RTV-adhesive layer. Isochromatic fringe patterns were obtained for models subjected to tension and combined tension and bending. Tests indicated that the load-transfer between the SIP and the photoelastic material occurred at discrete locations causing stress concentrations in the photoelastic material. Stress concentration factors of the order of 1.9 were measured, but as the observed photoelastic response was an integrated effect through the model thickness, the local stress concentration factors at the SIP/tile interface could be even higher.

Prabhakaran, R.↗

NASA NTRS1981

Wind loads on flat plate photovoltaic array fields

The results of an experimental analysis (boundary layer wind tunnel test) of the aerodynamic forces resulting from winds acting on flat plate photovoltaic arrays are presented. Local pressure coefficient distributions and normal force coefficients on the arrays are shown and compared to theoretical results. Parameters that were varied when determining the aerodynamic forces included tilt angle, array separation, ground clearance, protective wind barriers, and the effect of the wind velocity profile. Recommended design wind forces and pressures are presented, which envelop the test results for winds perpendicular to the array's longitudinal axis. This wind direction produces the maximum wind loads on the arrays except at the array edge where oblique winds produce larger edge pressure loads. The arrays located at the outer boundary of an array field have a protective influence on the interior arrays of the field. A significant decrease of the array wind loads were recorded in the wind tunnel test on array panels located behind a fence and/or interior to the array field compared to the arrays on the boundary and unprotected from the wind. The magnitude of this decrease was the same whether caused by a fence or upwind arrays.

Miller, R. D.↗

NASA NTRS1982

Results of a flight experiment on the catalytic efficiency of the Space Shuttle heat shield

An experiment was performed on the second Space Shuttle flight to verify data from arc-heated wind-tunnel tests indicating that the thermal protection tiles used on the Shuttle's surface are noncatalytic to the recombination of dissociated air. The experiment indicates that the tiles are indeed noncatalytic, and explains the lower than expected temperatures observed in the first two Shuttle flights. The data are reasonably well predicted with computations, using a chemically reactive boundary-layer code. The experimental setup and the computational analysis are described.

Rakich, J. V.↗

NASA NTRS1988

Cryogenic Insulation System

This invention relates to reusable, low density, high temperature cryogenic foam insulation systems and the process for their manufacture. A pacing technology for liquid hydrogen fueled, high speed aircraft is the development of a fully reusable, flight weight cryogenic insulation system for propellant tank structures. In the invention cryogenic foam insulation is adhesively bonded to the outer wall of the fuel tank structure. The cryogenic insulation consists of square sheets fabricated from an array of abutting square blocks. Each block consists of a sheet of glass cloth adhesively bonded between two layers of polymethacrylimide foam. Each block is wrapped in a vapor impermeable membrane, such as Kapton(R) aluminum Kapton(R), to provide a vapor barrier. Very beneficial results can be obtained by employing the present invention in conjunction with fibrous insulation and an outer aeroshell, a hot fuselage structure with an internal thermal protection system.

Davis, Randall C.↗