Results for “polymer films” — Page 41

NASA NTRS1990

LARC-TPI 1500 series controlled molecular weight polyimide

LARC-TPI, a linear high temperature thermoplastic polyimide, was developed several years ago at NASA Langley Research Center. This material has been commercialized by Mitsui Toatsu Chemicals, Inc., Tokyo, Japan, as a varnish and powder. More recently, a melt-extruded film of a controlled molecular weight of this same polymer has been supplied to NASA Langley Research Center for evaluation. This new form, called LARC-TPI 1500 series, has been prepared in three molecular weights - high, medium and low flow polymers. The subject of this investigation deals with the rheological properties of the high and medium flow powders and the adhesive properties of the medium flow melt-extruded film. Rheological studies indicate that the high and medium flow forms of the polymer fall in the flow range of injection moldable materials. Adhesive data generated on the medium flow extruded film shows this form to be well suited for structural adhesive bonding. The data are as good or better than that for LARC-TPI data of previous studies.

Progar, Donald↗

DOE OSTI2026

A Versatile Method for Creating Ultrathin Films of Polyzwitterions with Antifouling Properties

Protein repellent (i.e., antifouling) properties of ultrathin polymeric films have been ascribed to the formation of a dense layer of adsorbed polymers, which causes steric hindrance to protein adsorption on underlying substrates. The antifouling properties of the films are hypothesized to be independent of polymer hydrophilicity based on previous studies involving uncharged polymers. Here, to test the hypothesis and extend it to the realm of charged polymers, we have developed a grafting method for creating ultrathin layers of polyzwitterions on solid surfaces. To demonstrate the efficacy of this method, poly[1-(3-sulfopropyl-1)-2-vinylpyridinium betaine] (P2VPPS) was synthesized via free-radical polymerization and immobilized onto surfaces by using a photoreactive benzophenone derivative as the cross-linker, which was covalently bonded to either quartz or Si/SiOx substrates through a silane anchor. We found that ultrathin films with thicknesses of less than 10 nm can be obtained in dry states using 365 nm ultraviolet (UV) cured/cross-linked surface coatings. These films were found to be hydrophilic and undergo structural rearrangements in the presence of water. The antifouling performance of the films was evaluated using Pseudomonas aeruginosa strain PAO1 bacterium as the fouling agent and exhibited antifouling properties with a kinetic control via the coating method (i.e., spin-coating and drop-casting). In particular, the surface area coverages due to the PAO1 cell attachment on the quartz substrates coated with P2VPPS were found to be ∼5% and ∼0% for the spin-coated and drop-casted films, respectively, after 4 h. These results show that the grafting method can be used to generate surfaces with antifouling properties based on ultrathin films of polyzwitterions.

Pseudomonas aeruginosa↗

DOE OSTI2023

Phenazine-Substituted Poly(benzimidazobenzophenanthrolinedione): Electronic Structure, Thin Film Morphology, Electron Transport, and Mechanical Properties of an n-Type Semiconducting Ladder Polymer

Not provided.

Polymer Science↗

DOE OSTI2020

Barrier film, method of making the barrier film, and articles including the barrier film

A barrier film that includes a substrate, a first polymer layer on a major surface of the substrate, an oxide layer on the first polymer layer, and a second polymer layer on the oxide layer. At least one of the first or second polymer layers includes a siloxane reaction product of a secondary or tertiary amino-functional silane having at least two silane groups. A method of making the barrier film and articles and a barrier assembly including the barrier film are also disclosed.

36 MATERIALS SCIENCE↗

NASA NTRS2003

Development of Highly-Conductive Polyelectrolytes for Lithium Batteries

Future NASA and Air Force missions require reliable and safe sources of energy with high specific energy and energy density that can provide thousands of charge-discharge cycles at more than 40% depth- of-discharge and that can operate at low temperatures. All solid-state batteries have substantial advantages with respect to stability, energy density, storage fife and cyclability. Among all solid-state batteries, those with flexible polymer electrolytes offer substantial advantages in cell dimensionality and commensurability, low temperature operation and thin film design. The above considerations suggest that lithium-polymer electrolyte systems are promising for high energy density batteries and should be the systems of choice for NASA and US Air Force applications. Polyelectrolytes (single ion conductors) are among most promising avenues for achieving a major breakthrough 'in the applicability of polymer- based electrolyte systems. Their major advantages include unit transference number for the cation, reduced cell polarization, minimal salt precipitation, and favorable electrolyte stability at interfaces. Our research is focused on synthesis, modeling and cell testing of single ion carriers, polyelectrolytes. During the first year of this project we attempted the synthesis of two polyelectrolytes. The synthesis of the first one, the poly(ethyleneoxide methoxy acrylateco-lithium 1,1,2-trifluorobutanesulfonate acrylate, was attempted few times and it was unsuccessful. We followed the synthetic route described by Cowie and Spence. The yield was extremely low and the final product could not be separated from the impurities. The synthesis of this polyelectrolyte is not described in this report. The second polyelectrolyte, comb polysiloxane polyelectrolyte containing oligoether and perfluoroether sidechains, was synthesized in sufficient quantity to study the range of properties such as thermal stability, Li- ion- conductivity and stability toward lithium metal. Also, the batteries containing this polyelectrolyte were assembled and tested. The results are detailed below. The synthesis of another polyelectrolyte similar to polysiloxane polyelectrolyte has been started, however, the synthesis was not completed due to termination of the project.

Shriver, D. F.↗

DOE OSTI2025

Deuteration Effects on the Physical and Optoelectronic Properties of Donor–Acceptor Conjugated Polymers

The significant differences in scattering cross sections between deuterium and protium are unique to neutron scattering techniques and have been a long-standing area of interest within the neutron scattering community. Researchers have explored selective deuteration to manipulate scattering contrast in soft matter systems, leading to the widespread use of deuterium labeling in materials development. As deuteration changes the atomic mass, it alters physical properties such as molecular volume, polarizability, and polarity, which in turn may affect noncovalent interactions and crystal ordering. Despite previous studies, there remains a limited understanding of how deuteration impacts donor–acceptor (DA) conjugated polymers. To address this, we synthesized deuterated DPP polymers and systematically investigated the effects of side-chain deuteration on their thermal stability, crystal packing, morphology, and optoelectronic properties. We found that deuteration increased the melting and crystallization temperatures of DPP polymers, although it did not significantly alter their morphology, molecular packing, or charge mobility. These properties were assessed by using atomic force microscopy (AFM), X-ray scattering, and thin-film transistor device measurements, respectively, for DPP polymers. Our work shows that deuterium labeling could be a powerful method for controlling scattering length density, enabling neutrons to study the structure and dynamics of conjugated polymers without impacting their electronic performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS1978

Low-Temperature Chemiluminescence From cis-1,4-Polybutadiene, 1,2-Polybutadiene, and trans-Polypentenamer at Temperatures Near Ambient

The chemiluminescence emission at 25-60 C was measured from films of cis-1,4-polybutadiene, 1,2-polybutadiene, and trans-polypentenamer. The polymers were autoxidized previously in air 100 C, or allowed to react with singlet molecular oxygen in solution, and then cast into films. Values of beta(or k(sub d,((1)O2 yields (3)03)/k(sub r)((1)O2 + polymer yields products)) were determined in benzene for cis-1,4-polybutadiene and cis-1,4-polyisoprene, and for model compounds cis-3-hexene and cis-3-methyl-3-hexene by independent methods. The chemiluminescence emission from irradiated films of the polymers containing a dye sensitizer showed a complicated time dependence, and the results depended on the length of irradiation.

Nathan, Richard A.↗

NASA NTRS1995

Photodeposition of amorphous polydiacetylene films from monomer solutions onto transparent substrates

Polydiacetylenes are a very promising class of polymers for both photonic and electronic applications because of their highly conjugated structures. For these applications, high-quality thin polydiacetylene films are required. We have discovered a novel technique for obtaining such films of a polydiacetylene derivative of 2-methyl-4-nitroaniline using photodeposition from monomer solutions onto UV transparent substrates. This heretofore unreported process yields amorphous polydiacetylene films with thicknesses on the order of I micron that have optical quality superior to that of films grown by standard crystal growth techniques. Furthermore, these films exhibit good third-order nonlinear optical susceptibilities; degenerate four-wave mixing experiments give x(3) values on the order of 10(exp -8) - 10(exp -7) esu. We have conducted masking experiments which demonstrate that photodeposition occurs only where the substrate is directly irradiated, clearly indicating that the reaction occurs at the surface. Additionally, we have also been able to carry out photodeposition using lasers to form thin polymer circuits. In this work, we discuss the photodeposition of polydiacetylene thin films from solution, perform chemical characterization of these films, investigate the role of the substrate, speculate on the mechanism of the reaction, and make a preliminary determination of the third-order optical nonlinearity of the films. This simple, straightforward technique may ultimately make feasible the production of polydiacetylene thin films for technological applications.

Paley, M. S.↗

DOE OSTI2021

Unraveling the Unconventional Order of a High-Mobility Indacenodithiophene-Benzothiadiazole Copolymer

We report a new class of donor–acceptor (D-A) copolymers found to produce high charge carrier mobilities competitive with amorphous silicon (>1 cm 2 V –1 s –1 ) exhibit the puzzling microstructure of substantial local order, however lacking long-range order and crystallinity previously deemed necessary for achieving high mobility. Here, we demonstrate the application of low-dose transmission electron microscopy to image and quantify the nanoscale and mesoscale organization of an archetypal D-A copolymer across areas comparable to electronic devices (≈9 μm 2 ). The local structure is spatially resolved by mapping the backbone (001) spacing reflection, revealing nanocrystallites of aligned polymer chains throughout nearly the entire film. Analysis of the nanoscale structure of its ordered domains suggests significant short- and medium-range order and preferential grain boundary orientations. Moreover, we provide insights into the rich, interconnected mesoscale organization of this new family of D-A copolymers by analysis of the local orientational spatial autocorrelations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Polymer-Based Thermally Stable Chemiresistive Sensor for Real-Time Monitoring of NO 2 Gas Emission

Here, we present a thermally stable, mechanically compliant, and sensitive polymer-based NO 2 gas sensor design. Interconnected nanoscale morphology driven from spinodal decomposition between conjugated polymers tethered with polar side chains and thermally stable matrix polymers offers judicious design of NO 2 -sensitive and thermally tolerant thin films. The resulting chemiresitive sensors exhibit stable NO 2 sensing even at 170 °C over 6 h. Controlling the density of polar side chains along conjugated polymer backbone enables optimal design for coupling high NO 2 sensitivity, selectivity, and thermal stability of polymer sensors. Lastly, thermally stable films are used to implement chemiresistive sensors onto flexible and heat-resistant substrates and demonstrate a reliable gas sensing response even after 500 bending cycles at 170 °C. Such unprecedented sensor performance as well as environmental stability are promising for real-time monitoring of gas emission from vehicles and industrial chemical processes.

47 OTHER INSTRUMENTATION↗

DOE OSTI2023

Mechanical, Morphological, and Charge Transport Properties of NDI Polymers with Variable Built‐in Π‐Conjugation Lengths Probed by Simulation and Experiment

Abstract Mechanically deformable polymeric semiconductors are a key material for fabricating flexible organic thin‐film transistors (FOTFTs)—the building block of electronic circuits and wearable electronic devices. However, for many π‐conjugated polymers achieving mechanical deformability and efficient charge transport remains challenging. Here the effects of polymer backbone bending stiffness and film microstructure on mechanical flexibility and charge transport are investigated via experimental and computational methods for a series of electron‐transporting naphthalene diimide (NDI) polymers having differing extents of π‐conjugation. The results show that replacing increasing amounts of the π‐conjugated comonomer dithienylvinylene (TVT) with the π‐nonconjugated comonomer dithienylethane (TET) in the backbone of the fully π‐conjugated polymeric semiconductor, PNDI‐TVT 100 (yielding polymeric series PNDI‐TVT x , 100 ≥x≥ 0), lowers backbone rigidity, degree of texturing, and π–π stacking interactions between NDI moieties. Importantly, this comonomer substitution increases the mechanical robustness of PNDI‐TVT x while retaining efficient charge transport. Thus, reducing the TVT content of PNDI‐TVT x suppresses film crack formation and dramatically stabilizes the field‐effect electron mobility upon bending (e.g., 2 mm over 2000 bending cycles). This work provides a route to tune π–π stacking in π‐conjugated polymers while simultaneously promoting mechanical flexibility and retaining good carrier mobility in FOTFTs.

Chemistry↗

NASA NTRS2017

Monte Carlo Computational Modeling of Atomic Oxygen Interactions

Computational modeling of the erosion of polymers caused by atomic oxygen in low Earth orbit (LEO) is useful for determining areas of concern for spacecraft environment durability. Successful modeling requires that the characteristics of the environment such as atomic oxygen energy distribution, flux, and angular distribution be properly represented in the model. Thus whether the atomic oxygen is arriving normal to or inclined to a surface and whether it arrives in a consistent direction or is sweeping across the surface such as in the case of polymeric solar array blankets is important to determine durability. When atomic oxygen impacts a polymer surface it can react removing a certain volume per incident atom (called the erosion yield), recombine, or be ejected as an active oxygen atom to potentially either react with other polymer atoms or exit into space. Scattered atoms can also have a lower energy as a result of partial or total thermal accommodation. Many solutions to polymer durability in LEO involve protective thin films of metal oxides such as SiO2 to prevent atomic oxygen erosion. Such protective films also have their own interaction characteristics. A Monte Carlo computational model has been developed which takes into account the various types of atomic oxygen arrival and how it reacts with a representative polymer (polyimide Kapton H) and how it reacts at defect sites in an oxide protective coating, such as SiO2 on that polymer. Although this model was initially intended to determine atomic oxygen erosion behavior at defect sites for the International Space Station solar arrays, it has been used to predict atomic oxygen erosion or oxidation behavior on many other spacecraft components including erosion of polymeric joints, durability of solar array blanket box covers, and scattering of atomic oxygen into telescopes and microwave cavities where oxidation of critical component surfaces can take place. The computational model is a two dimensional model which has the capability to tune the interactions of how the atomic oxygen reacts, scatters, or recombines on polymer or nonreactive surfaces. In addition to the specification of atomic oxygen arrival details, a total of 15 atomic oxygen interaction parameters have been identified as necessary to properly simulate observed interactions and resulting polymer erosion that have been observed in LEO. The tuning of the Monte Carlo model has been accomplished by adjusting interaction parameters so the erosion patterns produced by the model match those from several actual LEO space experiments. Surface texturing in LEO can also be predicted by the model. Such comparison of space tests with ground laboratory experiments have enabled confidence in ground laboratory lifetime prediction of protected polymers. Results of Monte Carlo tuning, examples of surface texturing and undercutting erosion prediction, and several examples of how the model can be used to predict other LEO and Mars orbital space results are presented.

Monte Carlo Modeling↗

NASA NTRS2017

Monte Carlo Computational Modeling of Atomic Oxygen Interactions

Computational modeling of the erosion of polymers caused by atomic oxygen in low Earth orbit (LEO) is useful for determining areas of concern for spacecraft environment durability. Successful modeling requires that the characteristics of the environment such as atomic oxygen energy distribution, flux, and angular distribution be properly represented in the model. Thus whether the atomic oxygen is arriving normal to or inclined to a surface and whether it arrives in a consistent direction or is sweeping across the surface such as in the case of polymeric solar array blankets is important to determine durability. When atomic oxygen impacts a polymer surface it can react removing a certain volume per incident atom (called the erosion yield), recombine, or be ejected as an active oxygen atom to potentially either react with other polymer atoms or exit into space. Scattered atoms can also have a lower energy as a result of partial or total thermal accommodation. Many solutions to polymer durability in LEO involve protective thin films of metal oxides such as SiO2 to prevent atomic oxygen erosion. Such protective films also have their own interaction characteristics. A Monte Carlo computational model has been developed which takes into account the various types of atomic oxygen arrival and how it reacts with a representative polymer (polyimide Kapton H) and how it reacts at defect sites in an oxide protective coating, such as SiO2 on that polymer. Although this model was initially intended to determine atomic oxygen erosion behavior at defect sites for the International Space Station solar arrays, it has been used to predict atomic oxygen erosion or oxidation behavior on many other spacecraft components including erosion of polymeric joints, durability of solar array blanket box covers, and scattering of atomic oxygen into telescopes and microwave cavities where oxidation of critical component surfaces can take place. The computational model is a two dimensional model which has the capability to tune the interactions of how the atomic oxygen reacts, scatters, or recombines on polymer or nonreactive surfaces. In addition to the specification of atomic oxygen arrival details, a total of 15 atomic oxygen interaction parameters have been identified as necessary to properly simulate observed interactions and resulting polymer erosion that have been observed in LEO. The tuning of the Monte Carlo model has been accomplished by adjusting interaction parameters so the erosion patterns produced by the model match those from several actual LEO space experiments. Surface texturing in LEO can also be predicted by the model. Such comparison of space tests with ground laboratory experiments have enabled confidence in ground laboratory lifetime prediction of protected polymers. Results of Monte Carlo tuning, examples of surface texturing and undercutting erosion prediction, and several examples of how the model can be used to predict other LEO and Mars orbital space results are presented.

Atomic Oxygen↗

NASA NTRS1989

Polymer Coatings Reduce Electro-osmosis

Poly(ethylene glycol) film controls electrostatic potential. Electro-osmosis in quartz or glass chambers reduced or reversed by coating inside surface of chambers with monomacromolecular layers of poly(ethylene glycol). Stable over long times. Electrostatic potential across surface of untreated glass or plastic chamber used in electro-phoresis is negative and attracts cations in aqueous electrolyte. Cations solvated, entrains flow of electrolyte migrating toward cathode. Electro-osmotic flow interferes with desired electrophoresis of particles suspended in electrolyte. Polymer coats nontoxic, transparent, and neutral, advantageous for use in electrophoresis.

Herren, Blair J.↗

NASA NTRS1986

Polyimide of Modified Melt Flow and Toughness

Linear aromatic polyphenylene ether sulfideimide (BDSDA/APB) polymer molded, used as resin, and cast into thin films. In effort to improve further both use properties and amenability to process BDSDA/APB, molecular weight of polymer varied by variations in percentage of end capping. Effect of end capping BDSDA/APB determined by measurement of polymer melt viscosity and fracture-energy values for different number average synthesized molecular weights.

St. Clair, T. L.↗

DOE OSTI2023

Biodegradable High-Molecular-Weight Poly(pentylene adipate- co -terephthalate): Synthesis, Thermo-Mechanical Properties, Microstructures, and Biodegradation

Poly(pentylene adipate-co-terephthalate) (PPAT) is a promising biobased and biodegradable polymer that can replace polyethylene in flexible packaging films where biodegradability is desired. High-molecular-weight (100K–145 KDa) aliphatic–aromatic polyester PPAT was successfully synthesized, and the effects of reaction conditions on molecular weight were reported. PPAT polyesters were characterized for polymer compositions, number-average unit length, thermal transitions, and rheological properties. PPAT compression-molded films were characterized for crystallinity and tensile properties to correlate micro- and macroproperties. PPAT compression-molded films exhibited up to a 76% higher tensile modulus than compression-molded films from poly(butylene adipate-co-terephthalate) (PBAT), making PPAT films potentially comparable with compression-molded films from linear low-density polyethylene (LLDPE). Finally, PPAT is biodegradable in soil and freshwater environments with estimated 90% biodegradation times of 504–580 and 604–845 days, respectively, while PBAT takes 971 days in soil and 395 days in freshwater.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Molecular interactions that drive morphological and mechanical stabilities in organic solar cells

Morphological and mechanical stabilities of organic solar cells (OSCs) are of paramount importance to ensure long-lived devices. However, the fundamental drivers of these stability metrics and their competing relationship have yet to be well defined. Here, in this work, several high-performance polymers and small molecule acceptors (SMAs) are considered to assist in the development of a comprehensive view of the molecular drivers of, and interrelationships between, morphological and mechanical stabilities. We find that the SMAs drive much of the embrittlement and diffusion characteristics in the blend films. However, the heterointeraction of the SMA and polymer, probed through dynamic mechanical analysis, is a key contributing factor to the film toughness. The heterointeraction energy is ideally maximally negative (i.e., repulsive), deviating from the geometric mean of the homointeraction energy. These findings assist in introducing a framework to understand the active layer stability and highlight material properties that lead to morphologically stable and physically robust OSCs.

14 SOLAR ENERGY↗

DOE OSTI2020

Beyond Substrates: Strain Engineering of Ferroelectric Membranes

Strain engineering in perovskite oxides provides for dramatic control over material structure, phase, and properties, but is restricted by the discrete strain states produced by available high-quality substrates. Here, using the ferroelectric BaTiO3, production of precisely strain-engineered, substrate-released nanoscale membranes is demonstrated via an epitaxial lift-off process that allows the high crystalline quality of films grown on substrates to be replicated. In turn, fine structural tuning is achieved using interlayer stress in symmetric trilayer oxide-metal/ferroelectric/oxide-metal structures fabricated from the released membranes. Additionally, in devices integrated on silicon, the interlayer stress provides deterministic control of ordering temperature (from 75 to 425 °C) and releasing the substrate clamping is shown to dramatically impact ferroelectric switching and domain dynamics (including reducing coercive fields to <10 kV cm-1 and improving switching times to <5 ns for a 20 µm diameter capacitor in a 100-nm-thick film). In devices integrated on flexible polymers, enhanced room-temperature dielectric permittivity with large mechanical tunability (a 90% change upon ±0.1% strain application) is demonstrated. This approach paves the way toward the fabrication of ultrafast CMOS-compatible ferroelectric memories and ultrasensitive flexible nanosensor devices, and it may also be leveraged for the stabilization of novel phases and functionalities not achievable via direct epitaxial growth.

36 MATERIALS SCIENCE↗