Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “phase space methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

System overview on electromagnetic compensation for reflector antenna surface distortion

The system requirements and hardware implementation for electromagnetic compensation of antenna performance degradations due to thermal effects was investigated. Future commercial space communication antenna systems will utilize the 20/30 GHz frequency spectrum and support very narrow multiple beams (0.3 deg) over wide angle field of view (15-20 beamwidth). On the ground, portable and inexpensive very small aperture terminals (VSAT) for transmitting and receiving video, facsimile and data will be employed. These types of communication system puts a very stringent requirement on spacecraft antenna beam pointing stability (less than .01 deg), high gain (greater than 50 dB) and very lowside lobes (less than -25 dB). Thermal analysis performed on the advanced communication technology satellite (ACTS) has shown that the reflector surfaces, the mechanical supporting structures and metallic surfaces on the spacecraft body will distort due thermal effects from a varying solar flux. The antenna performance characteristics (e.g., pointing stability, gain, side lobe, etc.) will degrade due to thermal distortion in the reflector surface and supporting structures. Specifically, antenna RF radiation analysis has shown that pointing error is the most sensitive antenna performance parameter to thermal distortions. Other antenna parameters like peak gain, cross polarization level (beam isolation), and side lobe level will also degrade with thermal distortions. In order to restore pointing stability and in general antenna performance several compensation methods were proposed. In general these compensation methods can be classified as being either of mechanical or electromagnetic type. This paper will address only the later one. In this approach an adaptive phased array antenna feed is used to compensate for the antenna performance degradation. Extensive work has been devoted to demonstrate the feasibility of adaptive feed compensation on space communication antenna systems. This paper addresses the system requirements for such a system and identify candidate technologies (analog and digital) for possible hardware implementation.

Acosta, R. J.↗
NASA NTRS1995

General Fluid System Simulation Program to Model Secondary Flows in Turbomachinery

The complexity and variety of turbomachinery flow circuits created a need for a general fluid system simulation program for test data anomaly resolution as well as design review. The objective of the paper is to present a computer program that has been developed to support Marshall Space Flight Center's turbomachinery internal flow analysis efforts. The computer program solves for the mass. energy and species conservation equation at each node and flow rate equation at each branch of the network by a novel numerical procedure which is a combination of both Newton-Ralphson and successive substitution method and uses a thermodynamic property program for computing real gas properties. A generalized, robust, modular, and 'user-friendly' computer program has been developed to model internal flow rates, pressures, temperatures, concentrations of gas mixtures and axial thrusts. The program can be used for any network for compressible and incompressible flows, choked flow, change of phase and gaseous mixturecs. The code has been validated by comparing the predictions with Space Shuttle Main Engine test data.

Majumdar, Alok K.↗
DOE OSTI2021

High-fidelity kinetic modeling of instabilities and gyromotion physics in nonuniform low-beta plasmas

A fourth-order accurate continuum kinetic Vlasov solver and a systematic method for constructing customizable kinetic equilibria are demonstrated to be powerful tools for the study of nonuniform collisionless low-beta plasmas. The noise-free methodology is applied to investigate two gradient-driven instabilities in 4D (x,y,vx,vy) phase space: the Kelvin–Helmholtz instability and the lower hybrid drift instability. Nonuniform two-species configurations where ion gyroradii are comparable to gradient scale lengths are explored. The approach sheds light on the evolution of the pressure tensor in Kelvin–Helmholtz instabilities and demonstrates that the associated stress tensor deviates significantly from the gyroviscous stress tensor. Even at high magnetization, first-order approximations to finite-gyromotion physics are shown to be inadequate for the Kelvin–Helmholtz instability, as shear scales evolve to become on par with gyromotion scales. The methodology facilitates exploring transport and energy partitioning properties associated with lower hybrid drift instabilities in low-beta plasma configurations. Distribution function features are captured in detail, including the formation of local extrema in the vicinity of particle-wave resonances. Finally, the approach enables detailed targeted investigations and advances kinetic simulation capability for plasmas in which gyromotion plays an important role.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2026

Adaptively coupled phase retrieval in multi-peak Bragg coherent diffraction imaging

Recent advances in Bragg coherent diffraction imaging (BCDI) experimental techniques permit routine measurement of multiple Bragg peaks from a single crystalline grain. The resulting images contain the full lattice distortion vector field which can be differentiated to provide lattice strain and rotation. With the advent of fourth-generation synchrotron light sources, such multi-peak datasets are produced at high rates, facilitating the need for rapid phase retrieval of the multiple peaks and subsequent image analysis. Here we describe and demonstrate a new implementation of a coupled phase retrieval technique for multi-peak BCDI which simultaneously treats each Bragg peak of the dataset and produces a three-dimensional image of the crystal's morphology and lattice distortion field. In addition, this method uses the redundant information contained in the various Bragg diffraction patterns to detect and suppress spurious signal appearing on the detector in a subset of the measurements. Compared with manual data editing, adaptive coupling produces a more consistent phase profile in reciprocal space and sharper surfaces in direct space, with no significant difference in computational cost. These improvements reduce the need for manual preprocessing and enable robust high-throughput analysis of multi-peak BCDI data, supporting near-real-time strain microscopy at modern synchrotron facilities.

36 MATERIALS SCIENCE↗
NASA NTRS1984

Scan blindness in infinite phased arrays of printed dipoles

A comprehensive study of infinite phased arrays of printed dipole antennas is presented, with emphasis on the scan blindness phenomenon. A rigorous and efficient moment method procedure is used to calculate the array impedance versus scan angle. Data are presented for the input reflection coefficient for various element spacings and substrate parameters. A simple theory, based on coupling from Floquet modes to surface wave modes on the substrate, is shown to predict the occurrence of scan blindness. Measurements from a waveguide simulator of a blindness condition confirm the theory.

Pozar, D. M.↗
NASA NTRS1985

Some design philosophy for reducing the community noise of advanced counter-rotation propellers

Advanced counter-rotation propellers have been indicated as possibly generating an unacceptable amount of noise for the people living near an airport. This report has explored ways to reduce this noise level, which is treated as being caused by the interaction of the upstream propeller wakes and vortices with the downstream propeller. The noise reduction techniques fall into two categories: (1) reducing the strength of the wakes and vortices, and (2) reducing the response of the downstream blades to them. The noise from the wake interaction was indicated as being reduced by increased propeller spacing and decreased blade drag coefficient. The vortex-interaction noise could be eliminated by having the vortex pass over the tips of the downstream blade, and it could be reduced by increased spacing or decreased initial circulation. The downstream blade response could be lessened by increasing the reduced frequency parameter omega or by phasing of the response from different sections to have a mutual cancellation effect. Uneven blade to blade spacing for the downstream blading was indicated as having a possible effect on the annoyance of counter-rotation propeller noise. Although there are undoubtedly additional methods of noise reduction not covered in this report, the inclusion of the design methods discussed would potentially result in a counter-rotation propeller that is acceptably quiet.

Dittmar, J. H.↗
NASA NTRS1987

Expansion of space station diagnostic capability to include serological identification of viral and bacterial infections

It is necessary that an adequate microbiology capability be provided as part of the Health Maintenance Facility (HMF) to support expected microbial disease events during long periods of space flight. The applications of morphological and biochemical studies to confirm the presence of certain bacterial and fungal disease agents are currently available and under consideration. This confirmation would be greatly facilitated through employment of serological methods to aid in the identification for not only bacterial and fungal agents, but viruses as well. A number of serological approached were considered, particularly the use of Enzyme Linked Immunosorbent Assays (ELISAs), which could be utilized during space flight conditions. A solid phase, membrane supported ELISA for the detection of Bordetella pertussis was developed to show a potential model system that would meet the HMF requirements and specifications for the future space station. A second model system for the detection of Legionella pneumophilia, an expected bacterial disease agent, is currently under investigation.

Hejtmancik, Kelly E.↗
NASA NTRS1990

North Atlantic weather regimes: A synoptic study of phase space

In the phase space of weather, low frequency variability (LFV) of the atmosphere can be captured in a large scale subspace, where a trajectory connects consecutive large scale weather maps, thus revealing flow changes and recurrences. Using this approach, Vautard applied the trajectory speed minimization method (Vautard and Legras) to atmospheric data. From 37 winters of 700 mb geopotential height anomalies over the North Atlantic and the adjacent land masses, four persistent and recurrent weather patterns, interpreted as weather regimes, were discernable: a blocking regime, a zonal regime, a Greenland anticyclone regime, and an Atlantic regime. These regimes are studied further in terms of maintenance and transitions. A regime survey unveils preferences regarding event durations and precursors for the onset or break of an event. The transition frequencies between regimes vary, and together with the transition times, suggest the existence of easier transition routes. These matters are more systematically studied using complete synoptic map sequences from a number of events.

Orrhede, Anna Karin↗
NASA NTRS1992

Modelling a single phase voltage controlled rectifier using Laplace transforms

The development of a 20 kHz, AC power system by NASA for large space projects has spurred a need to develop models for the equipment which will be used on these single phase systems. To date, models for the AC source (i.e., inverters) have been developed. It is the intent of this paper to develop a method to model the single phase voltage controlled rectifiers which will be attached to the AC power grid as an interface for connected loads. A modified version of EPRI's HARMFLO program is used as the shell for these models. The results obtained from the model developed in this paper are quite adequate for the analysis of problems such as voltage resonance. The unique technique presented in this paper uses the Laplace transforms to determine the harmonic content of the load current of the rectifier rather than a curve fitting technique. Laplace transforms yield the coefficient of the differential equations which model the line current to the rectifier directly.

Kraft, L. Alan↗
NASA NTRS1994

Multi-Flight-Phase GPS Navigation Filter Applications to Terrestrial Vehicle Navigation and Positioning

A candidate onboard space navigation filter demonstrated excellent performance (less than 8 meter level RMS semi-major axis accuracy) in performing orbit determination of a low-Earth orbit Explorer satellite using single-frequency real GPS data. This performance is significantly better than predicted by other simulation studies using dual-frequency GPS data. The study results revealed the significance of two new modeling approaches evaluated in the work. One approach introduces a single-frequency ionospheric correction through pseudo-range and phase range averaging implementation. The other approach demonstrates a precise axis-dependent characterization of dynamic sample space uncertainty to compute a more accurate Kalman filter gain. Additionally, this navigation filter demonstrates a flexibility to accommodate both perturbational dynamic and observational biases required for multi-flight phase and inhomogeneous application environments. This paper reviews the potential application of these methods and the filter structure to terrestrial vehicle and positioning applications. Both the single-frequency ionospheric correction method and the axis-dependent state noise modeling approach offer valuable contributions in cost and accuracy improvements for terrestrial GPS receivers. With a modular design approach to either 'plug-in' or 'unplug' various force models, this multi-flight phase navigation filter design structure also provides a versatile GPS navigation software engine for both atmospheric and exo-atmospheric navigation or positioning use, thereby streamlining the flight phase or application-dependent software requirements. Thus, a standardized GPS navigation software engine that can reduce the development and maintenance cost of commercial GPS receivers is now possible.

Park, Young W.↗
NASA NTRS1999

SPARCLE Optical System Design and Operational Characteristics

The SPAce Readiness Coherent Lidar Experiment (SPARCLE) is the first demonstration of a coherent Doppler wind lidar in space. SPARCLE will be flown aboard a space shuttle In the middle part of 2001 as a stepping stone towards the development and deployment of a long-life-time operational instrument in the later part of next decade. SPARCLE is an ambitious project that is intended to evaluate the suitability of coherent lidar for wind measurements, demonstrate the maturity of the technology for space application, and provide a useable data set for model development and validation. This paper describes the SPARCLE's optical system design, fabrication methods, assembly and alignment techniques, and its anticipated operational characteristics. Coherent detection is highly sensitive to aberrations in the signal phase front, and to relative alignment between the signal and the local oscillator beams. Consequently, the performance of coherent lidars is usually limited by the optical quality of the transmitter/receiver optical system. For SPARCLE having a relatively large aperture (25 cm) and a very long operating range (400 km), compared to the previously developed 2-micron coherent lidars, the optical performance requirements are even more stringent. In addition with stringent performance requirements, the physical and environment constraints associated with this instrument further challenge the limit of optical fabrication technologies.

Amzajerdian, Farzin↗
NASA NTRS2006

Simulating Responses of Gravitational-Wave Instrumentation

Synthetic LISA is a computer program for simulating the responses of the instrumentation of the NASA/ESA Laser Interferometer Space Antenna (LISA) mission, the purpose of which is to detect and study gravitational waves. Synthetic LISA generates synthetic time series of the LISA fundamental noises, as filtered through all the time-delay-interferometry (TDI) observables. (TDI is a method of canceling phase noise in temporally varying unequal-arm interferometers.) Synthetic LISA provides a streamlined module to compute the TDI responses to gravitational waves, according to a full model of TDI (including the motion of the LISA array and the temporal and directional dependence of the arm lengths). Synthetic LISA is written in the C++ programming language as a modular package that accommodates the addition of code for specific gravitational wave sources or for new noise models. In addition, time series for waves and noises can be easily loaded from disk storage or electronic memory. The package includes a Python-language interface for easy, interactive steering and scripting. Through Python, Synthetic LISA can read and write data files in Flexible Image Transport System (FITS), which is a commonly used astronomical data format.

Armstrong, John↗
NASA NTRSDate not supplied

Space-borne Doppler Weather Radar Modeling for Radar Design Evaluation

A model has been developed to predict the reflectivity and Doppler performance of a spaceborne weather radar for atmospheric aerosol and cloud monitoring. The goal is to predict radar sensitivity, resolution, uncertainties and other key performance metrics vs. radar design parameters and hardware nonidealities. Analytical formulas are readily available to predict key performance metrics of a space-borne radar system as a function of design parameters such as antenna size, spacecraft velocity, transmit power, and receive noise figure. Effects of some system nonidealities such as antenna pointing errors, power amplifier nonlinearity and phase noise can be estimated using idealized methods. These analytical formulas use idealized forms of the antenna radiation pattern and weather statistics to predict system performance. However, it is desirable to have a more physical model based on discretized weather volumes in which the particle size distribution, Doppler distribution, and other parameters can be varied to study how the radar hardware design parameters and nonidealities affect the measurement of the weather reflectivity and Doppler characteristics. This would allow the radar designers to have more insight into what is being measured and the hardware parameters and errors that need to be carefully controlled to achieve best radar performance, as well as potential methods to calibrate the system or correct errors. This presentation will demonstrate some proof-of-concept Ka-band simulations where the discretized model agrees with the analytical formulas for a simple case where the elements in the discretized weather volume are defined by a constant reflectivity and simple velocity vectors. In particular, the system sensitivity and Doppler uncertainty are evaluated by analytical formulas as well as the discretized model. Future work will expand on this to include more complex weather scenarios and the addition of system nonidealities.

Sara Tucker↗
NASA NTRS1987

Response of joint dominated space structures

An efficient linearization method is presented for calculating the transient response of nonlinear systems due to initial disturbances. The method is an extension of the describing function approach in which the steady state response of the system is calculated by representing the nonlinear element, typically joints in the case of space structures, by impedances which are functions of the amplitude of response. Thus, the problem of solving the differential equation for the steady state response becomes one of solving a set of nonlinear algebraic equations involving the steady state amplitudes and phases of the system. It is shown that for the transient case the steady state impedances can be averaged over the range of responses in order to provide equivalent values of stiffness and damping that, for a given set of initial displacements, may be treated as being constant for purposes of calculating system response. Single degree of freedom system are used to demonstrate the method and to develop an approach for optimizing the joint's characteristics so as to minimize transient response times. The use of this method for response estimation and optimization in multiple degree of freedom systems is investigated.

Source record↗
DOE OSTI2022

The Earth Model Column Collaboratory (EMC 2 ) v1.1: an open-source ground-based lidar and radar instrument simulator and subcolumn generator for large-scale models

Abstract. Climate models are essential for our comprehensive understanding of Earth's atmosphere and can provide critical insights on future changes decades ahead. Because of these critical roles, today's climate models are continuously being developed and evaluated using constraining observations and measurements obtained by satellites, airborne, and ground-based instruments. Instrument simulators can provide a bridge between the measured or retrieved quantities and their sampling in models and field observations while considering instrument sensitivity limitations. Here we present the Earth Model Column Collaboratory (EMC2), an open-source ground-based lidar and radar instrument simulator and subcolumn generator, specifically designed for large-scale models, in particular climate models, but also applicable to high-resolution model output. EMC2 provides a flexible framework enabling direct comparison of model output with ground-based observations, including generation of subcolumns that may statistically represent finer model spatial resolutions. In addition, EMC2 emulates ground-based (and air- or space-borne) measurements while remaining faithful to large-scale models' physical assumptions implemented in their cloud or radiation schemes. The simulator uses either single particle or bulk particle size distribution lookup tables, depending on the selected scheme approach, to perform the forward calculations. To facilitate model evaluation, EMC2 also includes three hydrometeor classification methods, namely, radar- and sounding-based cloud and precipitation detection and classification, lidar-based phase classification, and a Cloud Feedback Model Intercomparison Project Observational Simulator Package (COSP) lidar simulator emulator. The software is written in Python, is easy to use, and can be straightforwardly customized for different models, radars, and lidars. Following the description of the logic, functionality, features, and software structure of EMC2, we present a case study of highly supercooled mixed-phase cloud based on measurements from the U.S. Department of Energy Atmospheric Radiation Measurement (ARM) West Antarctic Radiation Experiment (AWARE). We compare observations with the application of EMC2 to outputs from four configurations of the NASA Goddard Institute for Space Studies (GISS) climate model (ModelE3) in single-column model (SCM) mode and from a large-eddy simulation (LES) model. We show that two of the four ModelE3 configurations can form and maintain highly supercooled precipitating cloud for several hours, consistent with observations and LES. While our focus is on one of these ModelE3 configurations, which performed slightly better in this case study, both of these configurations and the LES results post-processed with EMC2 generally provide reasonable agreement with observed lidar and radar variables. As briefly demonstrated here, EMC2 can provide a lightweight and flexible framework for comparing the results of both large-scale and high-resolution models directly with observations, with relatively little overhead and multiple options for achieving consistency with model microphysical or radiation scheme physics.

58 GEOSCIENCES↗
NASA NTRS2022

The Earth Model Column Collaboratory (EMC2) v1.1: An Open-Source Ground-Based Lidar and Radar Instrument Simulator and Subcolumn Generator for Large-Scale Models

Climate models are essential for our comprehensive understanding of Earth's atmosphere and can provide critical insights on future changes decades ahead. Because of these critical roles, today's climate models are continuously being developed and evaluated using constraining observations and measurements obtained by satellites, airborne, and ground-based instruments. Instrument simulators can provide a bridge between the measured or retrieved quantities and their sampling in models and field observations while considering instrument sensitivity limitations. Here we present the Earth Model Column Collaboratory (EMC2), an open-source ground-based lidar and radar instrument simulator and subcolumn generator, specifically designed for large-scale models, in particular climate models, but also applicable to high-resolution model output. EMC2 provides a flexible framework enabling direct comparison of model output with ground-based observations, including generation of subcolumns that may statistically represent finer model spatial resolutions. In addition, EMC2 emulates ground-based (and air- or space-borne) measurements while remaining faithful to large-scale models' physical assumptions implemented in their cloud or radiation schemes. The simulator uses either single particle or bulk particle size distribution lookup tables, depending on the selected scheme approach, to perform the forward calculations. To facilitate model evaluation, EMC2 also includes three hydrometeor classification methods, namely, radar- and sounding-based cloud and precipitation detection and classification, lidar-based phase classification, and a Cloud Feedback Model Intercomparison Project Observational Simulator Package (COSP) lidar simulator emulator. The software is written in Python, is easy to use, and can be straightforwardly customized for different models, radars, and lidars. Following the description of the logic, functionality, features, and software structure of EMC2, we present a case study of highly supercooled mixed-phase cloud based on measurements from the U.S. Department of Energy Atmospheric Radiation Measurement (ARM) West Antarctic Radiation Experiment (AWARE). We compare observations with the application of EMC2 to outputs from four configurations of the NASA Goddard Institute for Space Studies (GISS) climate model (ModelE3) in single-column model (SCM) mode and from a large-eddy simulation (LES) model. We show that two of the four ModelE3 configurations can form and maintain highly supercooled precipitating cloud for several hours, consistent with observations and LES. While our focus is on one of these ModelE3 configurations, which performed slightly better in this case study, both of these configurations and the LES results post-processed with EMC2 generally provide reasonable agreement with observed lidar and radar variables. As briefly demonstrated here, EMC2 can provide a lightweight and flexible framework for comparing the results of both large-scale and high-resolution models directly with observations, with relatively little overhead and multiple options for achieving consistency with model microphysical or radiation scheme physics.

Earth Model Column Collaboratory↗
DOE OSTI2020

Synthesis and structural characterization of the new Zintl phases Ba 3 Cd 2 P 4 and Ba 2 Cd 2 P 3 . Rare example of small gap semiconducting behavior with negative thermopower within the range 300 K-700 K

The new Zintl phases Ba 3 Cd 2 P 4 and Ba 2 Cd 2 P 3 have been synthesized using Pb flux, which allowed for the growth of 4-5 mm large crystals. The structures were determined utilizing single-crystal X-ray diffraction methods. Both compounds crystalize in the monoclinic crystal system (space group C2/m (No. 12)) and their structures are closely related. The structure of Ba 3 Cd 2 P 4 can be seen as being comprised of divalent Ba atoms and conjoined CdP 4 tetrahedra in the form of [Cd 2 P 4 ] 6- layers. Within the layers, homoatomic P–P bonds are present, which if cleaved, leave two infinite [CdP 3 ] 7- chains running along the crystallographic b-axis. The other structure, that of Ba 2 Cd 2 P 3 , can be rationalized as also having divalent Ba atoms and conjoined CdP4 tetrahedra in the form of [Cd 2 P 3 ] 6- layers. These layers, again, can be visualized as chains that run down the crystallographic b-axis, which are further connected by P-P dimers. Electronic band structure calculations show that each structure has an optimal number of valence electrons, and therefore conform to the Zintl-Klemm concept. Accordingly, the two compounds can be considered small band gap semiconductors, with band gaps of ca. 0.1 eV and 0.6 eV for Ba3Cd2P4 and Ba 2 Cd 2 P 3 , respectively. Electrical resistivity measurements show that Ba3Cd2P4 displays a large resistivity value at room temperature and an experimental band gap of ca. 0.05 eV, which fits reasonably well with the theoretical predictions. Thermopower measurements show that throughout the temperature range 300 K-700 K, Ba 3 Cd 2 P 4 displays a negative Seebeck coefficient. Here, the extremum value of -84 μV is reached at 630 K, suggestive of an n-type semiconductor, a rarity among Zintl phases.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗