Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “packaging materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

Development and Application of a Tool for Optimizing Composite Matrix Viscoplastic Material Parameters

This document describes a recently developed analysis tool that enhances the resident capabilities of the Micromechanics Analysis Code with the Generalized Method of Cells (MAC/GMC) and its application. MAC/GMC is a composite material and laminate analysis software package developed at NASA Glenn Research Center. The primary focus of the current effort is to provide a graphical user interface (GUI) capability that helps users optimize highly nonlinear viscoplastic constitutive law parameters by fitting experimentally observed/measured stress-strain responses under various thermo-mechanical conditions for braided composites. The tool has been developed utilizing the MATrix LABoratory (MATLAB) (The Mathworks, Inc., Natick, MA) programming language. Illustrative examples shown are for a specific braided composite system wherein the matrix viscoplastic behavior is represented by a constitutive law described by seven parameters. The tool is general enough to fit any number of experimentally observed stress-strain responses of the material. The number of parameters to be optimized, as well as the importance given to each stress-strain response, are user choice. Three different optimization algorithms are included: (1) Optimization based on gradient method, (2) Genetic algorithm (GA) based optimization and (3) Particle Swarm Optimization (PSO). The user can mix and match the three algorithms. For example, one can start optimization with either 2 or 3 and then use the optimized solution to further fine tune with approach 1. The secondary focus of this paper is to demonstrate the application of this tool to optimize/calibrate parameters for a nonlinear viscoplastic matrix to predict stress-strain curves (for constituent and composite levels) at different rates, temperatures and/or loading conditions utilizing the Generalized Method of Cells. After preliminary validation of the tool through comparison with experimental results, a detailed virtual parametric study is presented wherein the combined effects of temperature and loading rate on the predicted response of a braided composite is investigated.

thermo-mechanical; MATLAB; GUI-Based Too↗

Application of Analytical Heat Transfer Models of Multi-layered Natural and Engineered Barriers in Potential High-Level Nuclear Waste Repositories - 12435

A combination of transient heat transfer analytical solutions for a finite line source, a series of point sources, and a series of parallel infinite line sources were combined with a quasi-steady-state multi-layered cylindrical solution to simulate the temperature response of a deep geologic radioactive waste repository with multi-layered natural and engineered barriers. This evaluation was performed to provide information to scientists and decision makers to compare candidate geologic media for a repository (crystalline rock [granite], clay, salt, and deep borehole), and to provide input for the future evaluation of the trade-off between pre-emplacement surface storage time, waste package size, and repository footprint. This approach was selected in favor of the finite element solution typically used to analyze the temperature response because it allowed rapid comparison of a large number of alternative disposal options and design configurations. More than 100 combinations of waste form, geologic environment, repository design configuration, and surface storage times were analyzed and compared. The analytical solution approach used to analyze the repository temperature response allowed rapid comparison of a large number of alternative disposal options and design configurations. More than 100 combinations of waste form, geologic environment, repository design configuration, and surface storage times were analyzed and compared. This approach allowed investigation of the sensitivity of the results to combinations of parameters that show that there is much flexibility to be gained in terms of spent fuel management options by varying a few key parameters. This initial analysis used representative design concepts and thermal constraints based on international design concepts, and it also included waste forms representing future fuel cycles with high burnup fuels. Unlike repository designs with large open tunnels and pre-closure ventilation, all of the disposal concepts analyzed in this study used enclosed emplacement modes, where the waste packages were in direct contact with encapsulating engineered or natural materials. The deep borehole repository concept limits the size of the SNF waste packages and may require rod consolidation to fit within the drill casing diameter. A single assembly waste package, assuming rod consolidation, was evaluated in the current analysis. Similar size restrictions apply for the HLW canisters. At this time no thermal constraints have been defined for the deep borehole repository concept. Representative EBS materials and properties were evaluated. However, changes in EBS design concepts and materials can also have significant effects on the maximum waste package surface temperature. Increased thermal conductivity of the buffer layer can be achieved by using an engineered buffer consisting of a mixture of graphite, sand, and bentonite [14]. One of the advantages of the analytical model is that it highlights the sensitivity of the results to the parameters that define the repository layout, including spacing between axial and lateral neighboring waste packages and drifts. It is clear that repository layout adjustments can be made to reduce the calculated peak temperatures. The results also show that significant reductions in required surface storage times can be achieved if higher thermal constraints can be justified Additional studies are planned to evaluate the trade-offs between surface storage times, repository layout parameters, and variations in EBS design concepts. Model validation and uncertainties will also be addressed. It is expected that shorter surface storage times and more optimized repository design configurations may be achieved. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

A Structured, Model-Based Systems Engineering Methodology for Operations System Design

Two widely accepted techniques for lowering the cost and risk of developing systems are (1) the use of a defined systems engineering (SE) process or methodology and (2) the reuse of existing (previously built) system components. The first technique is represented, for example, in materials published by NASA (e.g., NASA Systems Engineering Handbook) or by professional societies such as INCOSE (International Council on Systems Engineering). Well-formed SE techniques provide value by establishing the proper scope of the system (e.g., requirements), and by identifying and resolving problems relatively early in project lifecycles, when fixes are less expensive. The second technique (reuse) is applied most commonly to hardware and software; it seeks to avoid replicating design and implementation costs while also reducing risk by placing proven capabilities into operational use. In this paper, we outline a methodology combining these two techniques and extending reuse beyond hardware and software to foundational aspects of a Mission Operation System’s (MOS) design. We describe the system design artifacts that result (e.g., requirements, design documentation), as well as the reusable patterns and elements of the design, and their interrelationships. This approach is enabled by model-based systems engineering (MBSE) techniques and tools and is currently available in SysML form as a plug-in to MagicDraw. Additionally, usage of a rigorous MBSE approach allows for training materials and tutorials to be packaged within the overall model itself. The results of such an approach include decreased cost and risk during the design phase, improved ability of the MOS development team to investigate trade spaces and identify impacts to important flight-ground trade studies. Such results extend into decreased costs and risk in later phases due to improved design, decreased need for late fixes or development of "glue-ware" or scripts to fill unanticipated gaps in functionality, and improved ability to identify and plan testing and other validation activities. Finally, lower operational costs can be expected, both due to improved quality of the MOS, increased ease of maintaining updated knowledge of system configuration, and the fact that training and procedural materials are also updated at the same time as accepted system changes.

Bindschadler, Duane L.↗

hashin_shtrikman_mp: a package for the optimal design and discovery of multi-phase composite materials

hashin_shtrikman_mp is a tool for composites designers who have desired composite properties in mind, but who do not yet have an underlying formulation. The library utilizes the tightest theoretical bounds on the effective properties of composite materials with unspecified microstructure – the Hashin-Shtrikman bounds – to identify candidate theoretical materials, find real materials that are close to the candidates, and determine the optimal volume fractions for each of the constituents in the resulting composite. Its features include (i) leveraging of materials in the Materials Project database, (ii) integration with the Materials Project API, (iii) use of genetic machine-learning, (iv) agnosticism to underlying microstructure, and (v) ultimate engineering application, make it a tool with much broader applications than its predecessors.

97 MATHEMATICS AND COMPUTING↗

ITRW: Formulating a Roadmap for WBG and UWBG Materials and Devices

The purpose of the International Technology Roadmap for Wide-Bandgap Power Semiconductors (ITRW) Materials and Devices Working Group, which considers the materials science of Wide-and Ultra-Wide-Band-Gap (WBG and UWBG) semiconductors, in addition to device design, fabrication, and evaluation, is to formulate a long-term, international roadmap for WBG and UWBG materials and devices, consistent with the packaging and applications working groups of ITRW. The working group is co-chaired by Victor Veliadis (primarily representing silicon carbide (SiC) and related materials) and Robert Kaplar (primarily representing gallium nitride (GaN) and related materials, as well as emerging ultra-WBGs) and is split into four sub-working-groups, which are: 1) SiC materials and devices (co-chairs Jon Zhang and Mietek Bakowski). 2) Lateral GaN materials and devices (co-chairs Sameh Khalil and Peter Moens). 3) Vertical GaN materials and devices (co-chairs TBD). 4) Emerging UWBG materials and devices (co-chairs Mark Hollis). The first two subgroups represent technology that is far more mature than that of the latter two, and devices are available as commercial products in power applications. The primary focus of this article will be on developments in subgroups 1 and 2, with only brief descriptions of the latter two sub-groups, including future activities as they mature technologically.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Machining of Alloy 709 Creep-fatigue Specimens from G. O. Carlson Heat

Alloy 709 has been selected as the next candidate material for Section III, Division 5 qualification in the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code (BPVC) for elevated-temperature nuclear construction. The qualification data package requires an assortment of information and material data including tensile, creep, and creep-fatigue performance at elevated temperatures from different material heats. The goal of the project is to generate a dataset to support qualification of Alloy 709 material for ASME BPVC design code. Working towards the project goal, Idaho National Laboratory needs to conduct a series of tests on three different heats to support the A709 code case development. At present, there is a gap in the data package for one of the heats: Heat number 58776 manufactured by G.O. Carlson. To address this data gap, Argonne National Laboratory transmitted five plates of A709 heat 58776 manufactured by G.O. Carlson to Idaho National Laboratory. These plates were solution annealed at 1150°C and heat treated at 775°C for 10 hours. The objective of this specification is to procure a series of creep-fatigue specimens to support the qualification data package. The creep-fatigue specimen design captures the cyclic material performance at elevated temperature. The material performance data generated from specimens machined herein will support the ASME BPVC code case development and establish design limits, and design life curves for Alloy 709 material.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Results of apparent atomic oxygen reactions with spacecraft materials during shuttle flight STS-41G

The effect of atomic oxygen interaction experienced by polymeric-based spacecraft materials is described. An experimental package (ACOMEX) flown on shuttle mission STS-41G carried out the investigation of advanced composite specimens such as carbon-epoxy and Kevlar-epoxy both with and without protective coatings added to thermal protective paints and films. Information on the exposure environment of the specimens was provided by a carbon coated atomic oxygen fluence monitor together with a photographic record. Mass loss measurements and photomicrographs made possible the analysis of the effect of interaction. After a total of about 38 hours of equivalent normal exposure at 225 km altitude the results showed that unprotected exposed surfaces exhibited severe erosion and mass loss with the possibility of seriously degrading structural and thermal performance. However, the specimens with a thin fluorocarbon overcoat showed promise of providing a protective barrier to the attack without altering the base properties of the material.

Zimcik, D. G.↗

Assessment of Residual Stresses in 3013 Inner and Outer Containers and Teardrop Samples

This report is an assessment performed by LANL that examines packaging for plutonium-bearing materials and the resilience of its design. This report discusses residual stresses in the 3013 outer, the SRS/Hanford and RFETS/LLNL inner containers, and teardrop samples used in studies to assess the potential for SCC in 3013 containers. Residual tensile stresses in the heat affected zones of the closure welds are of particular concern.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Practical issues and applications for vacuum and hermetic microsystems packaging.

Microsystems packaging involves physically placing and electrically interconnecting a microelectronic device in a package that protects it from and interfaces it with the outside world. When the device requires a hermetic or controlled microenvironment, it is typically sealed within a cavity in the package. Sealing involves placing and attaching a lid, typically by welding, brazing, or soldering. Materials selection (e.g., the epoxy die attach), and process control (e.g., the epoxy curing temperature and time) are critical for reproducible and reliable microsystems packaging. This paper will review some hermetic and controlled microenvironment packaging at Sandia Labs, and will discuss materials, processes, and equipment used to package environmentally sensitive microelectronics (e.g., MEMS and sensors).

36 MATERIALS SCIENCE↗

FY 2017-Progress Report on the Design and Construction of the Sodium Loop SMT-3

This report provides an update on the design of a forced-convection sodium loop to be used for the evaluation of sodium compatibility of advanced Alloy 709 with emphasis on long term exposures of tensile, creep, fatigue, creep fatigue, and fracture toughness ASTM-size specimens in support of ASME Code qualification and NRC licensing. The report is a deliverable (Level 4) in FY17 (M4AT-17AN1602094), under the Work Package AT-17AN160209, “Sodium Compatibility” performed by Argonne National Laboratory (ANL), as part of the Advanced Materials Program for the Advanced Reactor Technology. This work package enables the development of advanced structural materials by providing corrosion, microstructure, and mechanical property data from the standpoint of sodium compatibility of advanced structural alloys. The first sodium loop (SMT-1) with a single tank was constructed in 2011 at ANL and has been in operation for exposure of subsize sheet specimens of advanced alloys at a single temperature. The second sodium loop with dual tanks (SMT-2) was constructed in 2013 and has been in operation for the exposure of subsize sheet specimens of advanced alloys at two different temperatures. The current loop (SMT-3) has been designed to incorporate sufficient chamber capacity to expose a large number of ASTM-size specimens to evaluate the sodium effects on tensile, creep, fatigue, creep-fatigue, and fracture toughness properties, in support of ASME Code Qualification and USNRC Licensing. The design of individual components for the third sodium loop SMT-3 is almost complete. The design also has been sent to an outside vendor for piping analysis to be in compliance with ASME Code. A purchase order has been placed with an outside vendor for the fabrication of major components such as the specimen exposure tanks. However, we have contracted with another vendor to establish the piping design in compliance with ASME design codes. The piping design was completed in FY2017 and the information is being transmitted to the tank fabricator. The SMT-3 loop will be located in Building 206 adjacent to the currently operating SMT-2 loop. In addition, we have demolished the aged power supply system in Building 206 and installed a new transformer, wiring, and power panels for the new loop. Procurement of some of the long lead items such as valves, EM pumps, EM flowmeters, etc. is in progress and will continue in FY 2018. The construction of components such as cold trap, economizers, piping arrangement etc. will be performed in the central shops at ANL. About 150 liters of sodium for the loop will be procured in early FY2018. The loop system is designed to circulate sodium through the sample tanks and the associated loop without an operator for an extended period of time. With the three sodium loops (with single-tank, dual-tank and four–tanks), materials can be tested at different sodium temperatures, and large tensile, creep, fatigue, creep-fatigue, and fracture toughness specimens can be exposed to sodium for extended periods of time and generate data on mechanical properties in support of ASME Code Qualification and USNRC Licensing of advanced Alloy 709 for use as a structural material in SFRs.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Packaging Certification program Methodology for Determining Dose Rates for Small Gram Quantities in Shipping Packagings

The Small Gram Quantity (SGQ) concept is based on the understanding that small amounts of hazardous materials, in this case radioactive materials (RAM), are significantly less hazardous than large amounts of the same materials. This paper describes a methodology designed to estimate an SGQ for several neutron and gamma emitting isotopes that can be shipped in a package compliant with 10 CFR Part 71 external radiation level limits regulations. These regulations require packaging for the shipment of radioactive materials, under both normal and accident conditions, to perform the essential functions of material containment, subcriticality, and maintain external radiation levels within the specified limits. By placing the contents in a helium leak-tight containment vessel, and limiting the mass to ensure subcriticality, the first two essential functions are readily met. Some isotopes emit sufficiently strong photon radiation that small amounts of material can yield a large dose rate outside the package. Quantifying the dose rate for a proposed content is a challenging issue for the SGQ approach. It is essential to quantify external radiation levels from several common gamma and neutron sources that can be safely placed in a specific packaging, to ensure compliance with federal regulations. The Packaging Certification Program (PCP) Methodology for Determining Dose Rate for Small Gram Quantities in Shipping Packagings provides bounding shielding calculations that define mass limits compliant with 10 CFR 71.47 for a set of proposed SGQ isotopes. The approach is based on energy superposition with dose response calculated for a set of spectral groups for a baseline physical packaging configuration. The methodology includes using the MCNP radiation transport code to evaluate a family of neutron and photon spectral groups using the 9977 shipping package and its associated shielded containers as the base case. This results in a set of multipliers for 'dose per particle' for each spectral group. For a given isotope, the source spectrum is folded with the response for each group. The summed contribution from all isotopes determines the total dose from the RAM in the container.

42 ENGINEERING↗

Controlling Beryllium Contaminated Material And Equipment For The Building 9201-5 Legacy Material Disposition Project

This position paper addresses the management of beryllium contamination on legacy waste. The goal of the beryllium management program is to protect human health and the environment by preventing the release of beryllium through controlling surface contamination. Studies have shown by controlling beryllium surface contamination, potential airborne contamination is reduced or eliminated. Although there are areas in Building 9201-5 that are contaminated with radioactive materials and mercury, only beryllium contamination is addressed in this management plan. The overall goal of this initiative is the compliant packaging and disposal of beryllium waste from the 9201-5 Legacy Material Removal (LMR) Project to ensure that beryllium surface contamination and any potential airborne release of beryllium is controlled to levels as low as practicable in accordance with 10 CFR 850.25.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Statistical Mechanics on Lattices (smol) v0.0.1

smol is a Python implementation of the Cluster Expansion Method and extensions of this methodology; which is used to fit applied lattice models from first principle calculations for subsequent use in Monte Carlo simulations for computing thermodynamic and statistical properties of atomic configuration. smol has a several notable advantages over other similar software packages. The first being its Python implementation which makes it easy to use even for users with little software and coding skills. Despite being implemented in Python, essential Monte Carlo routines are implemented in Cython such that performance is not compromised and is competitive even to similar software implemented in C/C++. Furthermore, the package has specific functionality for handling complex ionic materials (such as cathodes and electrolytes) that is not readily available in other packages. Lastly, the software has a flexible and modular design with the intention of making it fast and efficient to develop and extend the methodology.

Barroso-Luque, Luis↗

Differing Approaches to the Same Destination: SRS vs. Hanford Transportation Safety Document and Onsite Transportation Program - 17142

The United States Department of Energy, DOE Order 460.1C establishes packaging and transportation requirements to ensure the safety of DOE shipments of hazardous material. In accordance with DOE Order 460.1C, there are two general ways that radioactive material can be transferred if remaining within the boundary of a DOE site (i.e., onsite): 1) Packages can be transferred fully compliant with U. S. Department of Transportation (DOT) requirements; or 2) Packages can be transferred under an appropriately approved site-specific Transportation Safety Document (TSD) DOE G 460.1-1 - The Implementation Guide for Use with DOE Order 460.1A Packaging and Transportation Safety specifies the required format, content, and approval process for TSDs, but also allows great flexibility. Although developed using the same guidance, both the Savannah River Site and Hanford Site TSD programs were developed largely independent of each other. This paper compares both programs. Although at first glance the approaches seem dauntingly different, both result in surprisingly similar equivalent safety. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Examination of shipping package 9975-02403

SRNL examined shipping package 9975-02403 following storage of nuclear material in K-Area Complex (KAC). As a result of field surveillance activities in KAC, this package was identified to contain several non-conforming and other conditions. Further examination of this package in SRNL confirmed significant moisture and mold in the bottom layers of the lower fiberboard assembly, and identified additional corrosion along the seam weld and on the bottom of the drum. It was recently recommended that checking for corrosion along the bottom edge of the drum be implemented for packages that are removed from storage, as well as high wattage packages remaining in storage. The appearance of such corrosion on 9975-02403 further indicates that such corrosion may provide an indication of significant moisture concentration and related degradation within the package. This condition is more likely to develop in packages with higher internal heat loads.

99 GENERAL AND MISCELLANEOUS↗