Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “optical receivers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Coherent optical modulation for antenna remoting

A coherent fiber optic link employing wideband frequency modulation (FM) of the optical carrier is used to transfer radio frequency (RF) or microwave signals. This system is used to link a remotely located antenna to a conveniently located electronics processing site. The advantages of coherent analog fiber optic systems over non-coherent intensity modulated fiber optic analog transmission systems are described. An optical FM link employing an indirect transmitter to frequency modulate the optical carrier and a microwave delay line discriminator receiver is described. Measured performance data for a video signal centered at 60 MHz is presented showing the use of wideband FM in the link.

Fitzmartin, D. J.↗
NASA NTRS1993

Optical beam forming techniques for phased array antennas

Three optical beam forming techniques are identified as applicable to large spaceborne phased array antennas. They are 1) the fiber replacement of conventional RF phased array distribution and control components, 2) spatial beam forming, and 3) optical beam splitting techniques. Two novel optical beam forming approaches, i.e., the spatial beam forming with a 'smart pixel' spatial light modulator (SLM) and the optical beam splitting approaches are conceived with integrated quasi-optical components. Also presented are the transmit and receive array architectures with the new SLM.

Wu, Te-Kao↗
NASA NTRS1993

Calibration of the receiver channel for the GOPEX precursor experiments

Calibration measurements for the cooled (253 K) photomultiplier tube (PMT) detector, used on the receiver channel of the transmit/receive (T/R) switch for GOPEX, were conducted in the laboratory. A pulsed frequency-doubled neodymium:yttrium-aluminum-garnet (Nd:YAG) laser was used to direct 532-mn light on the PMT. By monitoring the energy per pulse of the light incident on the PMT, the minimum number of photons detected could be determined. These results agreed with the photon flux back-calculated from the PMT output waveform. Approximately 700 incident photons arriving during a temporal pulse width of approximately 65 nsec were detected with a signal-to-noise ratio (SNR) of approximately 1. Other receiver channel characteristics, such as PMT dark currents, optical transmission, and interference filter sensitivity to angle of light incidence, were also measured.

Biswas, A.↗
NASA NTRS1992

Project PARAS: Phased array radio astronomy from space

An orbiting radio telescope is proposed which, when operated in a very long baseline interferometry (VLBI) scheme, would allow higher than currently available angular resolution and dynamic range in the maps and the ability to observe rapidly changing astronomical sources. Using passive phased array technology, the proposed design consists of 656 hexagonal modules forming a 150-m diameter antenna dish. Each observatory module is largely autonomous, having its own photovoltaic power supply and low-noise receiver and processor for phase shifting. The signals received by the modules are channeled via fiber optics to the central control computer in the central bus module. After processing and multiplexing, the data are transmitted to telemetry stations on the ground. The truss frame supporting each observatory panel is a novel hybrid structure consisting of a bottom graphite/epoxy tubular triangle and rigidized inflatable Kevlar tubes connecting the top observatory panel and the bottom triangle. Attitude control and station keeping functions will be performed by a system of momentum wheels in the bus and four propulsion modules located at the compass points on the periphery of the observatory dish. Each propulsion module has four monopropellant thrusters and four hydrazine arcjets, the latter supported by either a photovoltaic array or a radioisotope thermoelectric generator. The total mass of the spacecraft is about 20,500 kg.

Nuss, Kenneth↗
NASA NTRS1999

Atmospheric Multiple Scattering Effects on GLAS Altimetry: Calculations of Single Pulse Bias - Part 1

Estimates of the effect of pulse stretching on satellite laser altimetry in particular the Geoscience Laser Altimeter System (GLAS), by cloud multiple scattering were made from an analytical method and from Monte Carlo calculations. The path delay of the return pulse was found to be largest for low-level clouds with particle radii (3-20 microns). The magnitude of the path delay was affected by several factors including cloud height, cloud optical depth, cloud particle size, particle shape, and receiver field of view. Polar aerosol and Rayleigh scattering usually added less than 1 cm to the overall path delay. Path delay estimates for all cloud conditions would be less if a simple Gaussian fit of the return pulse peak were used to measure the pulse's centroid. However, care must be taken in determining the centroid as factors such as pulse width, surface slope and the fitting method used will affect the estimate. A planned application for laser altimetry is high precision monitoring of the height change of polar ice sheets. In the absence of a correction algorithm, the required GLAS altimetry accuracies will not be achieved unless atmospheric channel information is used to remove profiles that are likely to be heavily contaminated by multiple scattering.

Duda, David P.↗
NASA NTRS1996

4482 Element Multispectral Hybrid PV/PC HgCdTe IRFPA for High Resolution Coverage of 3.7 - 15.4 Micrometers for the AIRS Instrument

The Atmospheric Infrared Sounder (AIRS) is a key facility instrument in the NASA Earth Observing System (EOS) program, being implemented to obtain comprehensive long-term measurements of earth processes affecting global change. The instrument performs passive IR remote sensing using a high resolution grating spectrometer with a wide spectral coverage (3.7 - 15.4 m) directing radiation onto a hybrid HgCdTe IRFPA operating at 58K in a vacuum package cooled to 155K. The hybrid HgCdTe FPA consists of twelve modules, 10 with multiplexed photovoltaic detectors and two with individually leaded out photoconductive detectors. The complex FPA has a large optical footprint, 53 mm x 66 mm, and receives energy dispersed from the grating through a precision filter assembly containing 17 narrow band filters. The backside illuminated PV detector arrays are fabricated from P-on-n double layer LPE grown heterojunction detectors in a bilinear format of 50 m x 100 m detectors, with from 232 to 420 detectors per module. For the MWIR bands four PV modules cover the 3.7 m to 8.22 m region. Low detector capacitance and low noise preamplifiers in the ROIC are key to achieving high sensitivities in these bands. Uniform quantum efficiencies and detectivities exceeding 3E13 cm-rtHz/W have been achieved. The LWIR region is covered by six PV modules spanning 8.8 m to 13.75 m. High detector resistance and very low ROIC preamplifier input noise are key to achieving high sensitivity. A detectivity exceeding 2E11 cm-rtHz/W has been achieved at the longest wavelength. Two additional PC modules cover the longest spectral bands out to 15.4 m. This high performance multispectral focal plane has been built and integrated with the dewar assembly, and is currently being integrated with the complete AIRS sensor.

Rutter, James↗
NASA NTRS1989

Analysis of a crossed Bragg cell acousto-optical spectrometer for SETI

The search for radio signals from extraterrestrial intelligent beings (SETI) requires the use of large instantaneous bandwidth (500 MHz) and high resolution (20 Hz) spectrometers. Digital systems with a high degree of modularity can be used to provide this capability, and this method has been widely discussed. Another technique for meeting the SETI requirement is to use a crossed Bragg cell spectrometer as described by Psaltis and Casasent. This technique makes use of the Folded Spectrum concept, introduced by Thomas. The Folded Spectrum is a 2-D Fourier Transform of a raster scanned 1-D signal. It is directly related to the long 1-D spectrum of the original signal and is ideally suited for optical signal processing. The folded spectrum technique has received little attention to date, primarily because early systems made use of photographic film which are unsuitable for the real time data analysis and voluminous data requirements of SETI. An analysis of the crossed Bragg cell spectrometer is presented as a method to achieve the spectral processing requirements for SETI. Systematic noise contributions unique to the Bragg cell system will be discussed.

NASA Discipline Number 52-60↗
NASA NTRS1994

(abstract) Neptune: CO and HCN Distributions from Observations at the CSO

We used the Caltech Submillimeter Observatory (CSO ) to make spatially unresolved observations of the 230.538 GHz 2-1 transition of CO and the 265.886 GHz 3-2 transition of HCN at Neptune. All observations used the 10.4 meter antenna with a double sideband SIS junction heterodyne receiver. Spectra were observed with parallel acousto-optic spectrometers simultaneously providing 580 MHz bandwidth at 0.57 MHz resolution and 50 MHz bandwidth at 0.049 MHz resolution. Observed line shapes agree with prior observations by Rosenqvist et al and Marten et al. Analysis of the line shapes and intensities will yield information about the distributions of CO and HCN in the stratosphere of Neptune, and these results will be compared with previous results. The data imply that the mixing ratios of CO and HCN must decrease with altitude somewhere within the pressure range from 1 to 0.001 mbar. HCN data will also address the sharp saturation-induced decrease in the HCN mixing ratio at the lower levels in the stratosphere.

Caltech Submillimeter Observatory SRO CO carbon mo↗
NASA NTRS2009

Compact Instruments Measure Heat Potential

Based in Huntsville, Alabama, AZ Technology Inc. is a woman- and veteran-owned business that offers expertise in electromechanical-optical design and advanced coatings. AZ Technology has received eight Small Business Innovation Research (SBIR) contracts with Marshall Space Flight Center for the development of spectral reflectometers and the measurement of surface thermal properties. The company uses a variety of measurement services and instruments, including the Spectrafire, a portable spectral emissometer it used to assist General Electric with the design of its award-winning Giraffe Warmer for neonatal intensive care units.

Source record↗
NASA NTRS2012

Airborne Measurements of Atmospheric Methane Column Abundance Made Using a Pulsed IPDA Lidar

We report airborne measurements of the column abundance of atmospheric methane made over an altitude range of 3-11 km using a direct detection IPDA lidar with a pulsed laser emitting at 1651 nm. The laser transmitter was a tunable, seeded optical parametric amplifier (OPA) pumped by a Nd:YAG laser and the receiver used a photomultiplier detector and photon counting electronics. The results follow the expected changes with aircraft altitude and the measured line shapes and optical depths show good agreement with theoretical calculations.

Riris, Haris↗
DOE OSTI2025

Quasi-optical beam tracing module development for millimeter-wave high-wavenumber collective scattering on the NSTX-U and EAST tokamaks

A Python3-based beam tracing code utilizing Quasi-Optics has been developed to track both incident and receiving beams in high-k collective millimeter wave scattering systems within magnetic fusion plasmas. In contrast to existing ray tracing codes that solely consider refraction, this beam tracing code incorporates diffraction phenomena, providing a more comprehensive calculation. Here, this enhanced capability allows for a more accurate calculation of the scattering volume and spatial resolution in high-k collective scattering systems, crucial for evaluating system performance and facilitating data analysis. Unlike Geometrical Optics, Quasi-Optics employs the complex eikonal method, representing a Gaussian beam as a collection of coupled rays to accurately preserve diffraction characteristics. The developed code is intended for application in NSTX-Upgrade and EAST high-k beam tracing analyses, targeting frequencies of 693 GHz and 270 GHz, respectively. The high-k system's primary objective is the observation of electron-scale instabilities. Employing a symplectic integrator, the code ensures numerical accuracy, assessed through the conservation of the Hamiltonian. With its precision and efficiency, the code facilitates rapid inter-shot analyses.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2006

Near Sun Free-Space Optical Communications from Space

Free-space optical communications offers expanded data return capacity, from probes distributed throughout the solar system and beyond. Space-borne and Earth-based optical transceivers used for communicating optically, will periodically encounter near Sun pointing. This will result in an increase in the scattered background light flux, often contributing to degraded link performance. The varying duration of near Sun pointing link operations relative to the location of space-probes, is discussed in this paper. The impact of near Sun pointing on link performance for a direct detection photon-counting communications system is analyzed for both ground- and space-based Earth receivers. Finally, impact of near Sun pointing on spaceborne optical transceivers is discussed.

free-space↗
DOE OSTI2020

Engineered optical fibers and uses thereof

A system comprises an electromagnetic radiation source, a polarizing element, a mode converter, an optical fiber, and a measurement device. The polarizing element receives electromagnetic radiation produced by the electromagnetic radiation source and outputs linearly-polarized electromagnetic radiation having a linear polarization angle θ1. The mode converter converts the linearly-polarized electromagnetic radiation to an orbital angular momentum (OAM) mode of linearly-polarized electromagnetic radiation with topological charge Li. The OAM mode of linearly-polarized electromagnetic radiation is a superposition of first and second OAM modes with topological charges Li and opposite circular polarizations. The optical fiber supports propagation of the first and second OAM modes with an absolute effective index difference Δneff greater than or equal to 5×10−5, such that linearly-polarized electromagnetic radiation with linear polarization angle θ2 is emitted by the optical fiber. The measurement device is configured to determine a property of the electromagnetic radiation based on the polarization angle θ2.

Ramachandran, Siddharth↗
DOE OSTI2025

Zinc(II) Monomeric, Dimeric, and Trimeric Photosensitizers with Microsecond‐Lived Intra‐ligand Charge Transfer Excited States Investigated through Time‐Resolved Optical and X‐Ray Spectroscopy

Zn II photosensitizers relative to Cu I complexes have received less attention due to their energetically higher metal‐to‐ligand charge transfer states. Three Zn II complexes, namely a Monomer, a bimetallic helicate, and a trimetallic helicate, bearing phenanthroline ligands are hereby studied through time‐resolved X‐ray absorption (tr‐XAS) and femto‐microsecond optical transient absorption spectroscopy (OTA). The formation of intraligand singlet charge transfer ( I ILCT) excited states is achieved within femtoseconds, followed by intersystem crossing (ISC) in nanoseconds to generate microsecond‐lived triplet ( 3 ILCT) states. Femtosecond OTA shows that the 1 ILCT states in the Monomer, Dimer, and Trimer occur within 235 fs, 683 fs, and 730 fs, respectively, while nano‐microsecond OTA and tr‐XAS show their 3 ILCT states to decay within 1.00 µs, 1.48 µs, and 1.51 µs. The ISC from the 1 ILCT to the 3 ILCT state for the Trimer is 42.8 ns compared to the Monomer and Dimer with ISC rates of less than 13 ns. These differences arise due to the stabilization by π‐π and CH‐π noncovalent interactions of the phenanthroline ligands. The dihedral and torsional angles indicate stronger ligand strains in the excited states of the Dimer and Trimer versus the Monomer. DFT calculations for the electrochemical oxidation potentials further highlight their capability in inducing photoredox processes.

earth-abundant Zn-based photosensitizers↗
NASA NTRS1985

Direct-detection optical communication with color coded pulse position modulation signaling

The performance characteristics of a direct-detection optical communication system which is based on a laser transmitter which produces single light pulses at selected nonoverlapping optical center frequencies are discussed. The signal format, called color coded pulse position modulation (CCPPM), uses more of the total available response bandwidth characteristics of the photodetector than does ordinary PPM signaling. The advantages of CCPPM signaling are obtained at the expense of an increased optical bandwidth of the transmitted signal and a more complicated transmitter and receiver structure. When the signal format is used in conjunction with block length Reed-Solomon codes, high data rates and reliable high-speed optical communications under conditions of optimal energy efficiency are obtained.

Davidson, F.↗
DOE OSTI2021

Transparent Refractory Aerogels for Efficient Spectral Control in High–Temperature Solar Power Generation

Although spectrally selective materials play a key role in existing and emerging solar thermal technologies, temperature-related degradation currently limits their use to below 700 °C in vacuum and even lower temperatures in air. Here a solar-transparent refractory aerogel that offers stable performance up to 800 °C in air is demonstrated, which is significantly greater than its silica counterpart. This improved stability is attributed to the formation of a refractory aluminum silicate phase, which is synthesized using a conformal single cycle of atomic layer deposition within the high-aspect-ratio pores of silica aerogels. Furthermore, based on direct heat loss measurements, the transparent refractory aerogel achieves a receiver efficiency of 75% at 100 suns and an absorber temperature of 700 °C, which is a 5% improvement over the state of the art. Transparent refractory aerogels may find widespread applicability in solar thermal technologies by enabling the use of lower-cost optical focusing systems and eliminating the need for highly evacuated receivers. In particular, a shift to higher operating temperatures while maintaining a high receiver efficiency can enable the use of advanced supercritical CO 2 power cycles and ultimately translate to an ≈10% (absolute) improvement in solar-to-electrical conversion efficiency relative to existing linear concentrating systems.

14 SOLAR ENERGY↗