SEARCH · Engineering Papers

Results for “operations flight operations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

All sources NASA NTRS DOE OSTI

NASA NTRS2005

Distributed Web-Based Expert System for Launch Operations

The simulation and modeling of launch operations is based on a representation of the organization of the operations suitable to experiment of the physical, procedural, software, hardware and psychological aspects of space flight operations. The virtual test bed consists of a weather expert system to advice on the effect of weather to the launch operations. It also simulates toxic gas dispersion model, and the risk impact on human health. Since all modeling and simulation is based on the internet, it could reduce the cost of operations of launch and range safety by conducting extensive research before a particular launch. Each model has an independent decision making module to derive the best decision for launch.

Bardina, Jorge E.↗

NASA NTRS2006

Space Shuttle Body Flap Actuator Bearing Testing for NASA Return to Flight

The Space Shuttle body flap (BF) is located beneath the main engine nozzles and is required for proper aerodynamic control during orbital descent. The body flap is controlled by four actuators connected by a common shaft and driven by the hydraulic power drive unit. Inspection of the actuators during refurbishment revealed three shaft bearings with unexpected damage. One was coated with black oxide on the balls and race wear surfaces, a second contained a relatively deep wear scar, and the third with scratches and an aluminum particle in the wear track. A shaft bearing life test program was initiated to measure the wear life and explain the 5.08-micrometer wear scar. A tribological analysis was conducted to demonstrate that the black oxide coated wear surfaces did not damage the bearing, interfere with the lubrication, or cause severe bearing wear. Pre-damaged (equivalent of 30 missions), commercial equivalent bearings and previously flown shaft bearings were tested at axial loads, speeds, and temperatures seen during flight operations. These bearing were successfully life tested at 60 C for 24 hours or 90 flights. With a safety factor of 4X, the bearings were qualified for 22 flights when only a maximum of 12 flights are expected. Additional testing at 23 C was performed to determine the lubricant life and to further understand the mechanism that caused the blackened balls. Test results indicating bearing life was shortened at a lower temperature surprised the investigators. Start\Stop bearing testing that closely simulates mission profile was conducted at 23 C. Results of this testing showed lubricant life of 12 flights including a safety factor of four. Additional testing with bearings that have the equivalent of 30 missions of damage is being tested at 23 C. These tests are being performed over the Shuttle load profile to demonstrate the residual bearing life in the actuators exceeds 12 missions. Testing showed that the end of the shaft bearing life was characterized by bearing temperature rise, preload drop, and the onset of a severe wear bearing failure mechanism. The severe wear failure mechanism is characterized by rough wear scars, extensive bearing wear and steel transfer between the balls and the races.

Jet, Timothy R.↗

NASA NTRS2018

Aircraft Exceedances Vary According to Time of Day and Workload

The Flight Operational Quality Assurance (FOQA) programs have been implemented in US and Europe to identify anomalous flights based on data recorded on board an aircraft in an effort to improve flight safety. Numerous methods have been developed to support the analysis of FOQA data. However, it is unclear how FOQA data relates to the performance of the pilot. We sought to characterize the frequency and type of flight exceedances extracted from FOQA data during a controlled pilot schedule in order to determine whether patterns of exceedances related to human control of the aircraft would change according to scheduling factors.

flight data↗

NASA NTRSDate not supplied

Wind Tunnel Testing Techniques for a Tandem Tilt-Wing, Distributed Electric Propulsion VTOL Aircraft

Urban Air Mobility (UAM) vertical takeoff and landing (VTOL) aircraftdesigns frequently include multiple distributed propulsors, complex wing-propulsor aerodynamics, significant airframe configuration changes during normal flight operations, and no historical database regarding the best ways to transition between vertical and horizontal flight. This paper describes the methodology used for wind tunnel testing of the Langley Aerodrome No. 8 (LA-8) in the NASA Langley 12-Foot Low-SpeedTunnel during multiple test entries in 2019 and2020. The LA-8 is a tandem tilt-wing aircraft with 4 motor-propellerunits and 4 control surfaces distributed across each wing, plus an inverted V-tail with 2 ruddervators on the fuselage. An initial tunnel entryused one-factor-at-a-time (OFAT) testing to (1) define candidate trimmed transition corridors between vertical and horizontal flight, (2) assess whether there was adequate control authority, and (3) define appropriatetest factor ranges for subsequent design of experiment (DOE) wind tunnel testing. The total number of independent variables for these wind tunnel tests (23) made DOE testing an efficient option for assessing the large number of potential interactions associated with the LA-8. The general advantages and disadvantages of OFAT and DOE wind tunnel testing techniques are also discussed –along with the benefits of a combined approach

wind tunnel research techniques↗

NASA NTRSDate not supplied

Robotic Manipulation Testbeds with HPSC

Interoperability and scalability of robotic manipulators will be key to develop and sustain a lunar surface and cislunar ecosystem. From in-space servicing, assembly, and manufacturing (ISAM) to logistics, maintenance, and science operations, robotic manipulation is a critical NASA capability need and the demand for high-performance spaceflight computing will only rise as robotic tasks become more autonomous. With increased complexity, testbeds for research, feasibility studies, and technology demonstrations will be essential. The Dexterous Robotics Team at NASA Johnson Space Center has established multiple robotic manipulation testbeds taking a supervised autonomous remote operations approach and plans to infuse High-Performance Spaceflight Computing (HPSC) to emulate the flight environment and close the gap between space technology development and flight operations.

Alex Sowell↗

NASA NTRS2016

Proof-of-Concept Demonstrations of a Flight Adjustment Logging and Communication Network

The National Airspace System is a highly complex system of systems within which a number of participants with widely varying business and operating models exist. From the airspace user's perspective, a means by which to operate flights in a more flexible and efficient manner is highly desired to meet their business objectives. From the air navigation service provider's viewpoint, there is a need for increasing the capacity of the airspace, while maintaining or increasing the levels of efficiency and safety that currently exist in order to meet the charter under which they operate. Enhancing the communication between airspace operators and users is essential in order to meet these demands. In the spring of 2015, a prototype system that implemented an airborne tool to optimize en-route flight paths for fuel and time savings was designed and tested. The system utilized in-flight Internet as a high-bandwidth data link to facilitate collaborative decision making between the flight deck and an airline dispatcher. The system was tested and demonstrated in a laboratory environment, as well as in-situ. Initial results from these tests indicate that this system is not only feasible, but could also serve as a growth path and testbed for future air traffic management concepts that rely on shared situational awareness through data exchange and electronic negotiation between multiple entities operating within the National Airspace System.

Underwood, Matthew C.↗

NASA NTRSDate not supplied

Roadmap to Cooperative Operating Practices for Strategic Conflict Detection and Resolution in the Upper Class-E Traffic Management Concept

As the governing body of flight operations in the highly anticipated emergent area of Upper Class E airspace (60,000 ft and above), the Federal Aviation Administration (FAA) has recognized the potential for a possible extensible traffic management system for new entrants into this domain. Following the successes with Unmanned Aircraft Systems (UAS) Traffic Management (UTM) and Advanced / Urban Air Mobility (AAM / UAM) Traffic Management programs, FAA put forth an initial concept of operations for supporting the start of the Upper Class E Traffic Management (ETM) concept. Like UTM and AAM / UAM, ETM is envisioned to also be a community-based, industry driven cooperative management concept. However, tailoring it to be adaptable to the atmospheric communication, navigation, and surveillance deficits, as well as the diverse vehicle and mission profiles operating in the ETM environment will be the challenge. As such, the National Aeronautics and Space Administration (NASA) Ames Research Center has been investigating several technologies that will help enable industry in the development of this new type of cooperative operating environment. These technologies are being prototyped and will be tested in a collaborative evaluation of an initial ETM system in late 2023. The evaluation will concentrate on building out ETM system technologies that will inform the participants regarding operational intent sharing, strategic conflict detection, and the resultant deconfliction process. In addition to the technical aspects, key roles and responsibilities will need to be defined. This will be done through exploring community-agreed upon Cooperative Operating Practices (COPs) that include procedures and capabilities to aid in timely, strategic conflict identification and resolution to be developed during the evaluation. As an initial step to the evaluation, the ETM research team at NASA Ames solicited industry feedback on various aspects of ETM operations from subject matter experts. A virtual tabletop walkthrough session was held over a two-day period to follow a roadmap through the functional steps needed to build COPs, focusing on strategic conflict detection and resolution. Overall, the ETM tabletop provided insights into how the community wanted to instantiate the generation and sharing of operational intent, detect strategic conflicts and resolve those conflicts using a preliminary set of procedural community-agreed upon COPs.

Upper Class-E Traffic Management (ETM)↗

NASA NTRS1986

Flight evaluation of augmented controls for approach and landing of powered-lift aircraft

Flight experiments were conducted with Ames Research Center's Quiet Short-Haul Research Aircraft to evaluate the influence of highly augmented control modes on the ability of pilots to execute precision instrument flight operations in the terminal area, particularly approaches to and landings on a short runway. The aircraft is a powered-lift, short-takeoff and landing configuration that is equipped with a modern digital fly-by-wire flight control system, a head-up display, and a solar head-down display that make it possible to investigate control concepts and display format and content for full envelope, powered-lift operations. Considerable attention has been devoted in this flight program to assessing flightpath and airspeed command and stabilization modes developed using nonlinear, inverse model-following methods. The primary benefit of this control concept was realized when the pilot was required to execute a complex transition and approach under instrument conditions and in the presence of a wide range of wind and turbulence conditions.

Franklin, J. A.↗

NASA NTRS1990

Trends and individual differences in response to short-haul fight operations

A survey of airline pilots was undertaken to determine normative patterns and individual differences in mood and sleep during short-haul flight operations. The results revealed that over the course of a typical 2-d trip, pilots experience a decline in positive mood, or activity, and an increase in negative mood, or tension. On layovers, pilots report experiencing sleep of shorter duration and poorer quality than at home. These patterns are very similar to those reported by Gander and Graeber and by Gander et al. using high-fidelity sleep and activity monitoring equipment. Examination of the impact of two personality dimensions extracted from the Jenkins Activity Survey measure of the Type A personality, Achievement Striving and Impatience/Irritability, suggested that Impatience/Irritability may serve as a marker of individuals most likely to experience health-related problems on trips. Achievement Striving may serve as a predictor of performance in crew settings.

Aircraft↗

NASA NTRS1972

Tracking and data system support for the Mariner Mars 1971 mission. Prelaunch phase through first trajectory correction maneuver, volume 1

The DSN command system provided the capability to enter commands in a computer at the deep space stations for transmission to the spacecraft. The high-rate telemetry system operated at 16,200 bits/sec. This system will permit return to DSS 14 of full-resolution television pictures from the spacecraft tape recorder, plus the other science experiment data, during the two playback periods of each Goldstone pass planned for each corresponding orbit. Other features included 4800 bits/sec modem high-speed data lines from all deep space stations to Space Flight Operations Facility (SFOF) and the Goddard Space Flight Center, as well as 50,000 bits/sec wideband data lines from DSS 14 to the SFOF, thus providing the capability for data flow of two 16,200 bits/sec high-rate telemetry data streams in real time. The TDS performed prelaunch training and testing and provided support for the Mariner Mars 1971/Mission Operations System training and testing. The facilities of the ETR, DSS 71, and stations of the MSFN provided flight support coverage at launch and during the near-earth phase. The DSSs 12, 14, 41, and 51 of the DSN provided the deep space phase support from 30 May 1971 through 4 June 1971.

Laeser, R. P.↗

NASA NTRS1988

Human factors: Aeronautics

The objectives of the Aeronautics Human Factors Research and Technology program are to provide the technology base and capability to design effective crew-cockpit systems and to advance solutions to human problems affecting air transport and rotorcraft effectiveness and safety. Advanced automation technologies, information display capabilities under computer control, and concern for the effects of human error in flight operations are elements which drive the directions of the program. Thus, the program has four thrusts: flight management, human engineering methods, rotorcraft, and subsonic transports.

Jenkins, James P.↗

NASA NTRS1987

Space station operations task force. Panel 2 report: Ground operations and support systems

The Ground Operations Concept embodied in this report provides for safe multi-user utilization of the Space Station, eases user integration, and gives users autonomy and flexibility. It provides for meaningful multi-national participation while protecting U.S. interests. The concept also supports continued space operations technology development by maintaining NASA expertise and enabling technology evolution. Given attention here are pre/post flight operations, logistics, sustaining engineering/configuration management, transportation services/rescue, and information systems and communication.

Source record↗

NASA NTRS1996

Coordinated Parallel Runway Approaches

The current air traffic environment in airport terminal areas experiences substantial delays when weather conditions deteriorate to Instrument Meteorological Conditions (IMC). Expected future increases in air traffic will put additional pressures on the National Airspace System (NAS) and will further compound the high costs associated with airport delays. To address this problem, NASA has embarked on a program to address Terminal Area Productivity (TAP). The goals of the TAP program are to provide increased efficiencies in air traffic during the approach, landing, and surface operations in low-visibility conditions. The ultimate goal is to achieve efficiencies of terminal area flight operations commensurate with Visual Meteorological Conditions (VMC) at current or improved levels of safety.

Koczo, Steve↗

NASA NTRS1994

Improvements to the Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) Calibration System

As a continuing effort to increase the calibration accuracy of the AVIRIS data a number of recent improvements have been implemented and are in the process of being tested during the 1994 flight season. These include the following innovations: A direct observation of a laboratory radiance standard is now used to double check the wide field-of-view calibration via an integrating sphere source. Launch site field calibration of the AVIRIS sensor is now being planned to augment the laboratory and inflight calibration. Modification to a dry air conditioning unit has been made to enable ground calibration at flight operating temperatures. One hundred lines of dark imagery has been added to the end of each flight line to assist in the analysis and removal of residual coherent noise. The intensity of the onboard calibration lamp has been modified to improve response in the blue end of the spectrum. Novel spectral filters have been installed in the onboard calibration source.

Airborne Visible/Infrared Imaging Spectrometer Cal↗

NASA NTRS2009

The Integrated Medical Model: A Risk Assessment and Decision Support Tool for Space Flight Medical Systems

The Integrated Medical Model (IMM) is a decision support tool that is useful to mission planners and medical system designers in assessing risks and designing medical systems for space flight missions. The IMM provides an evidence based approach for optimizing medical resources and minimizing risks within space flight operational constraints. The mathematical relationships among mission and crew profiles, medical condition incidence data, in-flight medical resources, potential crew functional impairments, and clinical end-states are established to determine probable mission outcomes. Stochastic computational methods are used to forecast probability distributions of crew health and medical resource utilization, as well as estimates of medical evacuation and loss of crew life. The IMM has been used in support of the International Space Station (ISS) medical kit redesign, the medical component of the ISS Probabilistic Risk Assessment, and the development of the Constellation Medical Conditions List. The IMM also will be used to refine medical requirements for the Constellation program. The IMM outputs for ISS and Constellation design reference missions will be presented to demonstrate the potential of the IMM in assessing risks, planning missions, and designing medical systems. The implementation of the IMM verification and validation plan will be reviewed. Additional planned capabilities of the IMM, including optimization techniques and the inclusion of a mission timeline, will be discussed. Given the space flight constraints of mass, volume, and crew medical training, the IMM is a valuable risk assessment and decision support tool for medical system design and mission planning.

Kerstman, Eric↗

NASA NTRSDate not supplied

TPSAS-NF1676L-18493-DND

The Air Traffic Operations Lab is a multi-fidelity, part-task, aircraft and air traffic operations simulation facility. Used to explore interactions between new airborne and ground-based tools in a NextGeneration ATC environment, including: - Concept-level flight operations research, looking at human decision making, situation awareness, transfer of authority/responsibility, etc. - Performance impact assessments of new operational concepts on the National Airspace System (NAS) - Rapid prototyping of new flight deck tools and automation - Concept-level safety assessments - Identification and evaluation of future communication, navigation, and surveillance (CNS) infrastructure requirements - Controller-pilot data link - Precision trajectory-based ops - Air-to-air data exchange

Michael T Palmer↗

NASA NTRS2023

Earth Independent Medical Operations (EIMO) Training Technical Interchange Meeting, 26th October 2023: Background and Summary of Discussion

On 26th October 2023, ExMC convened a panel of Subject Matter Experts (SMEs) from NASA, broadly representing Headquarters, the Human Research Program, Medical Operations, the Human Health and Performance Directorate at JSC, the Health and Medical Technical Authority, the Flight Operations Directorate, and representation from other Centers including: Ames Research Center (ARC), and Glenn Research Center (GRC). Representatives from the Canadian Space Agency also participated in this TIM. In addition, SMEs from industry included representation from the following entities: Axiom Space, Space Exploration Technologies Corporation, Level Ex, Shiny Box Interactive. Additional SMEs from academia included: University of Houston, Touro University, Weill Cornell Medical College and the Translational Research Institute for Space Health at Baylor College of Medicine. This group of stakeholders discussed the training issues related to facilitating EIMO. Sub-topics for this discussion included the following: - Pre-launch medical curriculum development - Ground-based training on medical hardware - Dental health - Behavioral health - Telemedicine - Just-in-time training - Simulation-based training (extended reality)

CMO Training↗

NASA NTRS2009

OTF Mission Operations Prototype Status

Reports on the progress of the JSC/OTF prototype of a CCSDS SM&C protocol based communications link between two space flight operations control centers. Varied implementations using software architectures from current web enterprise venues are presented. The AMS protocol (CCSDS Blue Book standard 735.1) was used for messaging and link communications.

Reynolds, Walter F.↗