Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “level sensor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Three-Zone Programmable Temperature Controller

Microprocessor-based controller regulates electrical power supplied to heater in each zone of three-zone directional-solidification furnace. Intended primarily for use in microgravity experiments aboard KC-135 airplane, controller also used on ground. Offers advantage of low electrical noise and consequent minimal interference with low-level signals put out by thermocouples and other sensors used in experiments. Achieved by heating with direct (instead of alternating) current and not pulsing heating current.

Smith, Guy A.↗
NASA NTRS1989

Portable Dextrous Force Feedback Master for robot telemanipulation (PDMFF)

A major drawback of open loop masters is a lack of force feedback, limiting their ability to perform complex tasks such as assembly and repair. Researchers present a simple dextrous force feedback master for computer assisted telemanipulation. The device is compact, portable and can be held in the operator hand, without the need for a special joystick or console. The system is capable of both position feed forward and force feedback, using electronic position sensors and a pneumatic micro-actuator. The level of forces exercised by the pneumatic actuator is such that near rigidity may be attained. Experimental results showing good system linearity and small time lag are given.

Burdea, Grigore C.↗
NASA NTRS1991

NASA radar altimeter for the Topex/Poseidon Project

The Topex/Poseidon Project is a joint U.S. and French mission to develop and operate an earth-orbiting satellite with sensors capable of making accurate measurements of sea level. The NASA Radar Altimeter (NRA), a fifth-generation U.S. altimeter, will provide the primary measurement for the Topex/Poseidon altimetric mission. This paper presents the requirements, altimeter fundamentals, design description, integration and test program, primary elements of ground processing, and assessment for the dual-frequency NRA.

Zieger, Alfred R.↗
NASA NTRS1995

SeaWiFS technical report series. Volume 28: SeaWiFS algorithms, part 1

This document provides five brief reports that address several algorithm investigations sponsored by the Calibration and Validation Team (CVT) within the Sea-viewing Wide Field-of-view Sensor (SeaWiFS) Project. This volume, therefore, has been designated as the first in a series of algorithm volumes. Chapter 1 describes the initial suite of masks, used to prevent further processing of contaminated radiometric data, and flags, which are employed to mark data whose quality (due to a variety of factors) may be suspect. In addition to providing the mask and flag algorithms, this chapter also describes the initial strategy for their implementation. Chapter 2 evaluates various strategies for the detection of clouds and ice in high latitude (polar and sub-polar regions) using Coastal Zone Color Scanner (CZCS) data. Chapter 3 presents an algorithm designed for detecting and masking coccolithosphore blooms in the open ocean. Chapter 4 outlines a proposed scheme for correcting the out-of-band response when SeaWiFS is in orbit. Chapter 5 gives a detailed description of the algorithm designed to apply sensor calibration data during the processing of level-1b data.

Hooker, Stanford B.↗
NASA NTRS2004

Mode Transitions for the ST7 Disturbance Reduction System Experiment

The Space Technology 7 Disturbance Reduction System experiment will perform an on-orbit system-level validation of two technologies: a gravitational reference sensor employing a free-floating test mass and a set of colloidal micronewton thrusters. The Disturbance Reduction System is designed to maintain the spacecraft s position with respect to a free floating test mass to less than 10 nm/& over the frequency range of 1 to 30 m= mi paper presents the modes that compose the Disturbance Reduction System spacecraft control as well as the strategy used to transition between modes. A high-fidelity model of the system, which incorporates rigid-body models of the spacecraft and two test masses (18 degrees of freedom), is developed and used to evaluate the performance of each mode and the efficacy of the transition strategy.

Hsu, Oscar C.↗
NASA NTRS2003

Advanced Microgravity Acceleration Measurement Systems (AMAMS) Being Developed

The Advanced Microgravity Acceleration Measurement Systems (AMAMS) project is part of NASA s Instrument Technology Development program to develop advanced sensor systems. The primary focus of the AMAMS project is to develop microelectromechanical systems (MEMS) for acceleration sensor systems to replace existing electromechanical sensor systems presently used to assess relative gravity levels aboard spacecraft. These systems are used to characterize both vehicle and payload responses to low-gravity vibroacoustic environments. The collection of microgravity acceleration data is useful to the microgravity life sciences, microgravity physical sciences, and structural dynamics communities. The inherent advantages of semiconductor-based systems are reduced size, mass, and power consumption, with enhanced long-term calibration stability.

Sicker, Ronald J.↗
NASA NTRS2008

Optical Detection of Formaldehyde

The potential for buildup .of formaldehyde in closed space environments poses a direct health hazard to personnel. The National Aeronautic Space Agency (NASA) has established a maximum permitted concentration of 0.04 ppm for 7 to 180 days for all space craft. Early detection is critical to ensure that formaldehyde levels do not accumulate. above these limits. New sensor technologies are needed to enable real time,in situ detection in a compact and reusable form factor. Addressing this need,research into the use of reactive fluorescent dyes which reversibly bind to formaldehyde (liquid or gas) has been conducted to support the development of a formaldehyde.sensor. In the presence of formaldehyde the dyes' characteristic fluorescence peaks shift providing the basis for an optical detection. Dye responses to formaldehyde exposure were characterized; demonstrating the optical detection of formaldehyde in under 10 seconds and down to concentrations of 0.5 ppm. To .incorporate the dye .in.an optical sensor device requires. a means of containing and manipulating the dye. Multiple form factors using two dissimilar s~bstrates were considered to determine a suitable configuration. A prototype sensor was demonstrated and considerations for a field able sensor were presented. This research provides a necessary first step toward the development of a compact, reusable; real time optical formaldehyde sensor suitable for use in the U.S. space program,

Patty, Kira D.↗
NASA NTRS2008

Near-Real Time Cloud Retrievals from Operational and Research Meteorological Satellites

A set of cloud retrieval algorithms developed for CERES and applied to MODIS data have been adapted to analyze other satellite imager data in near-real time. The cloud products, including single-layer cloud amount, top and base height, optical depth, phase, effective particle size, and liquid and ice water paths, are being retrieved from GOES- 10/11/12, MTSAT-1R, FY-2C, and Meteosat imager data as well as from MODIS. A comprehensive system to normalize the calibrations to MODIS has been implemented to maximize consistency in the products across platforms. Estimates of surface and top-of-atmosphere broadband radiative fluxes are also provided. Multilayered cloud properties are retrieved from GOES-12, Meteosat, and MODIS data. Native pixel resolution analyses are performed over selected domains, while reduced sampling is used for full-disk retrievals. Tools have been developed for matching the pixel-level results with instrumented surface sites and active sensor satellites. The calibrations, methods, examples of the products, and comparisons with the ICESat GLAS lidar are discussed. These products are currently being used for aircraft icing diagnoses, numerical weather modeling assimilation, and atmospheric radiation research and have potential for use in many other applications.

Minnis, Patrick↗
NASA NTRS2009

Spreadsheets for Analyzing and Optimizing Space Missions

XCALIBR (XML Capability Analysis LIBRary) is a set of Extensible Markup Language (XML) database and spreadsheet- based analysis software tools designed to assist in technology-return-on-investment analysis and optimization of technology portfolios pertaining to outer-space missions. XCALIBR is also being examined for use in planning, tracking, and documentation of projects. An XCALIBR database contains information on mission requirements and technological capabilities, which are related by use of an XML taxonomy. XCALIBR incorporates a standardized interface for exporting data and analysis templates to an Excel spreadsheet. Unique features of XCALIBR include the following: It is inherently hierarchical by virtue of its XML basis. The XML taxonomy codifies a comprehensive data structure and data dictionary that includes performance metrics for spacecraft, sensors, and spacecraft systems other than sensors. The taxonomy contains >700 nodes representing all levels, from system through subsystem to individual parts. All entries are searchable and machine readable. There is an intuitive Web-based user interface. The software automatically matches technologies to mission requirements. The software automatically generates, and makes the required entries in, an Excel return-on-investment analysis software tool. The results of an analysis are presented in both tabular and graphical displays.

Some, Raphael R.↗
NASA NTRS2011

Integrated Control with Structural Feedback to Enable Lightweight Aircraft

This presentation for the Fundamental Aeronautics Program Technical Conference covers the benefits of active structural control, related research areas, and focuses on the use of optimal control allocation for the prevention of critical loads. Active control of lightweight structures has the potential to reduce aircraft weight and fuel burn. Sensor, control law, materials, control effector, and system level research will be necessary to enable active control of lightweight structures. Optimal control allocation with structural feedback has been shown in simulation to be feasible in preventing critical loads and is one example of a control law to enable future lightweight aircraft.

Taylor, Brian R.↗
NASA NTRS2005

Feed-Back Moisture Sensor Control for the Delivery of Water to Plants Cultivated in Space

The development of a spaceflight-rated Porous Tube Insert Module (PTIM) nutrient delivery tray has facilitated a series of studies evaluating various aspects of water and nutrient delivery to plants as they would be cultivated in space. We report here on our first experiment using the PTIM with a software-driven feedback moisture sensor control strategy for maintaining root zone wetness level set-points. One-day-old wheat seedlings (Tritium aestivum cv Apogee; N=15) were inserted into each of three Substrate Compartments (SCs) pre-packed with 0.25-1 . mm Profile(TradeMark) substrate and maintained at root zone relative water content levels of 70, 80 and 90%. The SCs contained a bottom-situated porous tube around which a capillary mat was wrapped. Three Porous Tubes. were planted using similar protocols (but without the substrate) and also maintained at these three moisture level set-points. Half-strength modified Hoagland's nutrient solution was used to supply water and nutrients. Results on hardware performance, water usage rates and wheat developmental differences between the different experimental treatments are presented.

Levine, Howard G.↗
NASA NTRSDate not supplied

A Brief Status Update on Venus Long Lived Lander Technologies

The extreme surface conditions of Venus, including high temperature/pressure and reactive chemistry, have previously limited the lifetime of surface missions to ~2 hours. However, recent advances in high temperature technologies suggest the possibility of extended duration missions on the Venus surface. This presentation gives a brief overview on a range of high temperature technologies to enable a possible extended duration Venus surface mission. This presentation highlights the technology development under the Long-Lived In Situ Solar System Explorer (LLISSE) project and related technologies. The LLISSE project aimed towards developing a full lander system operational for 60 days on the Venus surface and included a power source, electronics, communications, sensors, and the structure, each at a different level of maturity. This presentation briefly describes these and other lander system technologies, their relative level of maturity, and planned future development for Venus surface exploration.

Venus surface exploration high temperature technol↗
NASA NTRSDate not supplied

An Overview of Long-Lived Venus Lander Technologies

The extreme surface conditions of Venus, including high temperature/pressure and reactive chemistry, have previously limited the lifetime of surface missions to ~2 hours. However, recent advances in high temperature technologies suggest the possibility of extended duration missions on the Venus surface. This presentation gives a brief overview on a range of high temperature technologies to enable a possible extended duration Venus surface mission, as well as an overview of the motivation and challenges of Venus surface exploration. The technology development under the Long-Lived In Situ Solar System Explorer (LLISSE) project and related technologies will be emphasized. The LLISSE project aimed towards developing a full lander system operational for 60 days on the Venus surface and included a power source, electronics, communications, sensors, and the structure, each at a different level of maturity. This presentation briefly describes these and other lander system technologies, their relative level of maturity, and planned future development for Venus surface exploration.

Venus surface exploration high temperature technol↗
NASA NTRSDate not supplied

An Overview of High Temperature Venus Surface Lander and Smart Systems Technologies

The extreme surface conditions of Venus, including high temperature/pressure and reactive chemistry, have previously limited the lifetime of surface missions to ~2 hours. Recent advances in high temperature technologies suggest the possibility of extended duration missions on the Venus surface. This presentation gives a brief overview of a range of high temperature technologies to enable a possible extended duration Venus surface mission, as well as an overview of the motivation and challenges of Venus surface exploration. The technology development under the Long-Lived In Situ Solar System Explorer (LLISSE) project is aimed towards developing a full lander system operational for 60 days on the Venus surface and included a power source, electronics, communications, sensors, and the structure, each at a different level of maturity. This presentation briefly describes these and other lander system technologies, their relative level of maturity, and planned future development for Venus surface exploration. Relevance to Aeronautic applications is briefly discussed.

Venus high temperature technologies vehicle health↗
NASA NTRSDate not supplied

A Brief Overview of High Temperature Technologies for a Venus Long Lived Lander

The extreme surface conditions of Venus, including high temperature/pressure and reactive chemistry, have previously limited the lifetime of surface missions to ~2 hours. However, recent advances in high temperature technologies suggest the possibility of extended duration missions on the Venus surface. This presentation gives a brief overview on a range of high temperature technologies to enable a possible extended duration Venus surface mission. The technology development under the Long-Lived In Situ Solar System Explorer (LLISSE) project and related technologies will be emphasized as well as that in the High Operating Temperature Technologies (HOTTech) program. The LLISSE project aimed towards developing a full lander system operational for 60 days on the Venus surface and included a power source, electronics, communications, sensors, and the structure, each at a different level of maturity. This presentation briefly describes these and other lander system technologies, their relative level of maturity, and planned future development for Venus surface exploration. It also describes the relevant capabilities and development approach to enable such a mission at NASA Glenn Research Center.

Venus surface↗
DOE OSTI2017

Drones in Automation - Secured Unmanned Aerial Systems

Factories, refineries, utilities (water/wastewater, electric) and related industrial sites are complex systems and structures with inspection and maintenance procedures required for optimal operation and regulatory compliance. As a specific example, consider just the bulk electric power system which is comprised of more than 200,000 miles of highvoltage transmission lines, thousands of generation plants and millions of digital controls. More than 1,800 entities own and operate portions of the grid system, with thousands more involved in the operation of distribution networks across North America. The interconnected and interdependent nature of the bulk power system requires a consistent and systematic application of risk mitigation across the entire grid system to be truly effective. Similar situations are found throughout automation where frequently an aging infrastructure is in place too. Consider, for example, the situation present in a refinery or chemical processing setting with the requirement for leak detection inspection of pipes, interconnects and systems stretching across the plant. The current practices and challenges relating just to this task - leak detection and repair (LDAR) – of detecting any fugitive emissions present and documenting all measurements thereby meeting air compliance regulations are typically “handled” by a small army of individuals with handheld or backpack-sized detectors who crawl through piping racks conducting measurements at each flange. Such work is performed in difficult conditions (temperature, humidity, physically challenging) with frequently a high level of employee turnover. Finaly, enter low cost sensors and mobile platforms – in other words unmanned aerial systems (UASs, or drones) with enhanced sensing capabilities.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2018

Voltammetric determination of vitamin B{sub 6} (pyridoxine) at a graphite screen-printed electrode modified with graphene oxide/Fe{sub 3}O{sub 4}@SiO{sub 2} nanocomposite

The preparation and study of electrochemical properties of a graphite screen-printed electrode (SPE) modified with the GO/Fe{sub 3}O{sub 4}@SiO{sub 2} (GO is graphene oxide) nanocomposites are described. The morphologies of the GO/Fe{sub 3}O{sub 4}@SiO{sub 2} nanocomposites were examined by scanning electron microscopy. The electrochemical oxidation of vitamin B{sub 6} (pyridoxine) on SPE modified with the GO/Fe{sub 3}O{sub 4}@SiO{sub 2} nanocomposite was investigated by cyclic voltammetry, differential pulse voltammetry, and chronoamperometry. Under optimum conditions (pH 7.0), the vitamin B{sub 6} oxidation at the surface of the modified SPE occurs at a potential about 190 mV less positive than that at the unmodified SPE. A linear voltammetric response for vitamin B{sub 6} was obtained in the concentration range 1.0•10 {sup 6}—9.0•10 {sup 4} mol L{sup –1} with a detection limit of 5.2•10 {sup 7} mol L{sup –1} using differential pulse voltammetry. The developed sensor was also successfully applied for determination of trace level of vitamin B{sub 6} in both the standard vitamin B{sub 6} sample and biological samples (urine).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗