Results for “ion mobility” — Page 41

NASA NTRSDate not supplied

Simulation Studies for an Urban Air Mobility Aircraft using Hardware-In-Loop Experiments

Urban Air Mobility seeks to transport passengers, deliver cargo, and provide emergency transportation in major metropolitan areas. This will be accomplished with distributed electric-powered vertical takeoff and landing aircraft. The low specific energy of the current generation lithium-ion battery packs limit the operational range of electric aircraft. Limited range impacts safety by reducing the time available for analyzing and responding to errors and failures, and limiting the ability to fly to an alternative landing area or return to base. It is therefore critical to understand flight operational and environmental conditions that impact the onboard lithium-ion polymer battery pack’s health. With this as the motivation, experimental procedure in a laboratory setting, and results of the experiments performed on battery packs subject to power draw corresponding to power required during the different phases of flight of a NASA conceptual quadrotor aircraft in simulation are described. The fully charged battery is allowed to discharge at specific C-rates based on the power draw profile and the current and voltages are recorded. Observed results under different operating conditions and mission profiles are discussed.

UAM↗

DOE OSTI2020

Formation of multicomponent alloy particles in doped ceria under I 2+ ion irradiation and thermal annealing

Multicomponent alloys resembling the e-phase particles in nuclear fuel have the potential to immobilize 99 Tc in a stable waste form. Formation of such multicomponent alloys under extreme conditions is studied in a non-activated model system: CeO 2 doped with 2 wt% Mo, 1.5 wt% Ru, 0.75 wt% Pd, 0.5 wt% Re and 0.25 wt% Rh. The doped CeO 2 films were irradiated with I 2+ ions (610°C, 10 16 and 5×10 16 I 2+ /cm 2 ). For selected samples post-irradiation heat treatment was conducted (900°C, 1100°C). Analytical TEM revealed the formation of 5-20 nm precipitates containing Pd, Mo, and Re sometimes associated with cavities. Iodine was found to segregate to grain boundaries and cracks. After heat treatment at 1100°C, the CeO 2 matrix had recrystallized. Precipitates containing Pd, Mo, Re, and Ru were observed near the interface with the polycrystalline YSZ substrate. It follows that Pd is the most mobile element, followed by Mo and Re. Finally, while irradiation promotes precipitation, high-temperature effects are more significant.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Chlorine gas and anion radical reactivity in molten salts and the link to chlorobasicity

Next-generation nuclear power plants may include exciting novel designs in which molten salts are the coolant or a combination of the coolant and fuel. Whereas it is straightforward to see why having a low volatility coolant can be advantageous for safety, much is not understood about the production of volatile halogen gases as a result of radiation and even less is known about the distribution of these species at and away from interfaces. Using first principles molecular dynamics simulations, we investigate the product of the disproportionation reaction between chlorine anion radicals (nominally Cl 2 ˙ − ) in the bulk and slab configurations. We find that the product depends on the chlorobasicity of the medium. For example, in ZnCl 2 , Cl 2 forms, but in a eutectic mixture of LiCl and KCl, Cl 3 − is formed as a product. We also find that Cl 3 − prefers to form at the vapor interface and this may have implications for corrosion and reactivity. Furthermore, the mechanisms of the mobility of Cl 2 and Cl 3 − are radically different, the first one being vehicular and the second Grotthus-like. Chlorobasicity is linked to the electronic structure of the host melt; ZnCl 2 forms extended networks along which metal ions and anionic counterions have significant electronic orbital overlap forming long, linear, molecular-like constructs; the opposite is true for the alkali metal eutectic salt.

Nguyen, Hung H. [Univ. of Iowa, Iowa City, IA (Uni↗

NASA NTRSDate not supplied

Simulation Studies for an Urban Air Mobility Aircraft using Hardware-In-Loop Experiments

Urban Air Mobility seeks to transport passengers, deliver cargo, and provide emergency medical transportation in major metropolitan areas. This will be accomplished with distributed electric powered vertical takeoff and landing aircraft vehicles. The low specific energy of the current generation lithium-ion battery packs limit the operational range of the electric aircraft. Limited range impacts safety by reducing the amount of time available for analyzing the potential impact of errors and failures and responding to them, and for flying to an alternative landing area or returning to the base. It is therefore critical to understand the impact of flight and environmental conditions on the onboard lithium-ion battery pack’s health. With this as the motivation, the procedure for evaluating the performance of battery packs in a laboratory setting and the results obtained using this procedure on battery packs subject to power draw characteristics of a simulated flight of a NASA conceptual quadrotor aircraft model are described. The fully charged battery is allowed to discharge at specific C-rates based on the power draw profile during the experiment, and the current and voltages are recorded as a function of time. Observed results under different operating conditions and mission profiles are discussed.

UAM↗

DOE OSTI2020

Realizing Complete Solid-Solution Reaction in High Sodium Content P2-Type Cathode for High-Performance Sodium-Ion Batteries

P2-type layered oxides suffer from an ordered Na + /vacancy arrangement and P2→O2/OP4 phase transitions, leading them to exhibit multiple voltage plateaus upon Na + extraction/insertion. The deficient sodium in the P2-type cathode easily induces the bad structural stability at deep desodiation states and limited reversible capacity during Na + de/insertion. These drawbacks cause poor rate capability and fast capacity decay in most P2-type layered oxides. In this work, to address these challenges, a novel high sodium content (0.85) and plateau-free P2-type cathode-Na 0.85 Li 0.12 Ni 0.22 Mn 0.66 O 2 (P2-NLNMO) was developed. The complete solid-solution reaction over a wide voltage range ensures both fast Na + mobility (10 -11 to 10 -10 cm 2 s -1 ) and small volume variation (1.7%). Furthermore, the high sodium content P2-NLNMO exhibits a higher reversible capacity of 123.4 mAhg -1 , superior rate capability of 79.3 mAhg -1 at 20 C, and 85.4% capacity retention after 500 cycles at 5 C. The sufficient Na and complete solid-solution reaction are critical to realizing high-performance P2-type cathodes for sodium-ion batteries.

25 ENERGY STORAGE↗

NASA NTRS2018

Ion Velocity in the Discharge Channel and Near-Field of the HERMeS Hall Thruster

NASA is continuing the development of a 12.5-kW Hall thruster system, which is baselined in a phased exploration concept to expand human presence to cis-lunar space and eventually to Mars. The development team is transitioning knowledge gained from the testing of the government-built Technology Development Unit (TDU) to the contractor-built Engineering Development Unit (EDU). A new laser-induced fluorescence diagnostic that is compatible with the testing of engineering hardware was developed to obtain data for thruster model validation in the lowest background pressure achievable. Prior to performing the test on the EDU, the team performed a functional checkout test of this new diagnostic using the TDU. In addition to providing a checkout of the diagnostic, this test provided data that can be correlated to electron mobility for comparison to the EDU at a later date. A number of technical challenges related to large test facilities and interfacing with engineering hardware were overcome while implementing the new laser diagnostic system. The initial data set was in good agreement with prior optical and non-optical diagnostics data collected on the TDU thrusters. This data set also revealed the spatial origin of high angle ions that have been of concern for spacecraft integration.

Huang, Wensheng↗

NASA NTRS2018

Ion Velocity in the Discharge Channel and Near-Field of the HERMeS Hall Thruster

NASA is continuing the development of a 12.5-kW Hall thruster system, which is baselined in a phased exploration concept to expand human presence to cis-lunar space and eventually to Mars. The development team is transitioning knowledge gained from the testing of the government-built Technology Development Unit (TDU) to the contractor-built Engineering Development Unit (EDU). A new laser-induced fluorescence diagnostic that is compatible with the testing of engineering hardware was developed to obtain data for thruster model validation in the lowest background pressure achievable. Prior to performing the test on the EDU, the team performed a functional checkout test of this new diagnostic using the TDU. In addition to providing a checkout of the diagnostic, this test provided data that can be correlated to electron mobility for comparison to the EDU at a later date. A number of technical challenges related to large test facilities and interfacing with engineering hardware were overcome while implementing the new laser diagnostic system. The initial data set was in good agreement with prior optical and non-optical diagnostics data collected on the TDU thrusters. This data set also revealed the spatial origin of high angle ions that have been of concern for spacecraft integration.

Huang, Wensheng↗

NASA NTRS2018

Ion Velocity in the Discharge Channel and Near-Field of the HERMeS Hall Thruster

NASA is continuing the development of a 12.5-kW Hall thruster system, which is baselined in a phased exploration concept to expand human presence to cis-lunar space and eventually to Mars. The development team is transitioning knowledge gained from the testing of the government-built Technology Development Unit (TDU) to the contractor-built Engineering Development Unit (EDU). A new laser-induced fluorescence diagnostic that is compatible with the testing of engineering hardware was developed to obtain data for thruster model validation in the lowest background pressure achievable. Prior to performing the test on the EDU, the team performed a functional checkout test of this new diagnostic using the TDU. In addition to providing a checkout of the diagnostic, this test provided data that can be correlated to electron mobility for comparison to the EDU at a later date. A number of technical challenges related to large test facilities and interfacing with engineering hardware were overcome while implementing the new laser diagnostic system. The initial data set was in good agreement with prior optical and non-optical diagnostics data collected on the TDU thrusters. This data set also revealed the spatial origin of high angle ions that have been of concern for spacecraft integration.

Huang, Wensheng↗

DOE OSTI2021

Unique Features of Polarization in Ferroelectric Ionic Conductors

Abstract Ferroelectrics that are also ionic conductors offer possibilities for novel applications with high tunability, especially if the same atomic species causes both phenomena. In particular, at temperatures just below the Curie temperature, polarized states may be sustainable as the mobile species is driven in a controlled way over the energy barrier that governs ionic conduction, resulting in unique control of the polarization. This possibility is recently demonstrated in CuInP 2 S 6 , a layered ferroelectric ionic conductor in which Cu ions cause both ferroelectricity and ionic conduction. Here, it is shown that the commonly used approach to calculate the polarization of evolving atomic configurations in ferroelectrics using the modern theory of polarization, namely concerted (synchronous) migration of the displacing ions, is not well suited to describe the polarization evolution as the Cu ions cross the van der Waals gaps. An asynchronous Cu‐migration scheme is introduced, which reflects the physical process by which Cu ions migrate, resolves the difficulties, and describes the polarization evolution both for normal ferroelectric switching and for transitions across the van der Waals gaps, providing a single framework to discuss ferroelectric ionic conductors.

O'Hara, Andrew↗

DOE OSTI2024

Hydrothermal solubility of Dy hydroxide as a function of pH and stability of Dy hydroxyl aqueous complexes from 25 to 250 °C

The rare earth elements (REE) have important applications in green energy technologies. The formation of mineral deposits in geologic systems commonly involves hydrothermal fluids which can mobilize the REE. However, the REE speciation is not well known as a function of pH. The thermodynamic properties of REE hydroxyl complexes used in geochemical models are based on the Helgeson-Kirkham-Flowers (HKF) equation of state parameters which were derived by extrapolation of low temperature experimental and estimated data. In this study, Dy hydroxide solubility experiments are combined with available literature data to improve these models from 25 to 250 °C and optimize the thermodynamic properties of Dy 3+ and Dy hydroxyl complexes using GEMSFITS. Batch-type solubility experiments were conducted from 150 to 250 °C and at saturated water vapor pressure in perchloric acid solutions with initial pH values of 2 to 5 in 0.5 pH unit increments. The measured solubility of Dy hydroxide is retrograde with temperature and decreases with pH. The logarithm of total dissolved Dy molality ranges from –2.3 to –5.3 at 150 °C (pH 4.7–5.5), from –2.4 to –5.6 at 200 °C (pH 3.9–5.1), and from –3.7 to –6.9 at 250 °C (pH of 3.4 and 5.0). The optimized standard partial molal Gibbs energies of formation (Δ f G° T ) derived for Dy 3+ and DyOH 2+ display a close to linear relationship with temperature, fitting with previous optimizations based on DyPO 4 solubility data in the literature. A comparison of the optimized ΔfG°T values for aqueous Dy species with predictions from available HKF parameters indicates significant differences ranging from +11 to –26 kJ/mol between 25 and 250 °C. The experimental fits are used to derive the Dy hydroxide solubility products (K s0 ) and formation constants for the hydrolysis of Dy (β n with n = 1 to 3; Dy 3+ + nOH – = DyOH n 3-n ) as a function of temperature. The optimization method presented yields accurate thermodynamic properties for the Dy 3+ aqua ions and the DyOH 2+ species at the acidic to mildly acidic pH studied whereas more experimental work is needed at near-neutral and alkaline conditions to better constrain the other hydroxyl complexes. Furthermore, the optimized thermodynamic data have a significant impact on geochemical modeling of the mobility and solubility of REE minerals in acidic hydrothermal fluids.

58 GEOSCIENCES↗

DOE OSTI2021

Strong Enhancement of Nanoconfined Water Mobility by a Structure Breaking Salt

For the majority of the water present on earth, the two most important factors influencing its behavior are confinement, in either inorganic or organic matrixes, and the presence of solutes. Here, we investigate the effect of confinement in 3 nm pores on water diffusivity in aqueous solutions with archetypical solutes, a structure making (kosmotrope) NaCl and a structure breaking (chaotrope) KCl, up to 1.0 M in concentration. The water diffusivity in bulk aqueous solutions in such a concentration range is known to decrease very slightly in the presence of NaCl and increase very slightly in the presence of KCl. However, here we observe the water diffusivity in confined H 2 O–KCl increases by a factor of 2 compared to the pure water diffusivity in the same confinement. This unusually strong cumulative effect of confinement and a structure breaking additive may have profound implications for the mobility and transport of aqueous species in nature.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2025

Electronic mobility, doping, and defects in epitaxial BaZrS 3 chalcogenide perovskite thin films

We present the electronic transport properties of BaZrS 3 thin films grown epitaxially by gas-source molecular beam epitaxy. We observe n-type behavior in all samples, with carrier concentration ranging from 4 × 10 18 to 4 × 10 20 cm −3 at room temperature (RT). We observe a champion RT Hall mobility of 11.1 cm 2 V −1 s −1 , which is competitive with established thin-film photovoltaic absorbers. Temperature-dependent Hall mobility data show that phonon scattering dominates at room temperature, in agreement with computational predictions. X-ray diffraction data illustrate a correlation between mobility and antiphase boundary concentration, illustrating how microstructure can affect transport. Despite the well-established environmental stability of chalcogenide perovskites, we observe significant changes to electronic properties as a function of storage time in ambient conditions. With the help of secondary ion mass spectrometry measurements, we propose and support a defect mechanism that explains this behavior: as-grown films have a high concentration of sulfur vacancies that are shallow donors (V ⋅ S or V ⋅⋅ S ), which are converted into neutral oxygen defects (O$^{×}_{S}$) upon air exposure. We discuss the relevance of this defect mechanism within the larger context of chalcogenide perovskite research, and we identify means to stabilize the electronic properties.

Van Sambeek, Jack [Massachusetts Institute of Tech↗

DOE OSTI2022

Investigation of Rare Earth Elements Mobility Using Molecular Dynamics

Rare Earth Elements (REE) are critical many applications such as electronics, permanent magnets, agricultural etc. Effective separation of REEs is a challenge due to their similarities in chemical and physical properties. Current separation processes are costly and environmentally detrimental. Therefore, research on REEs mobility in water-based solvents is necessary to design effective separation processes. In this research, the key kinetic and thermodynamic parameters, including diffusion coefficient and hydration shell are determined under the influence of external electric field. The diffusion coefficient of metal ions increases due to electric field in pure water.

99 GENERAL AND MISCELLANEOUS↗

DOE OSTI2022

Investigation of Rare Earth Elements Mobility Using Molecular Dynamics

Rare Earth Elements (REE) are critical many applications such as electronics, permanent magnets, agricultural etc. Effective separation of REEs is a challenge due to their similarities in chemical and physical properties. Current separation processes are costly and environmentally detrimental. Therefore, research on REEs mobility in water-based solvents is necessary to design effective separation processes. In this research, the key kinetic and thermodynamic parameters, including diffusion coefficient and hydration shell are determined under the influence of external electric field. The diffusion coefficient of metal ions increases due to electric field in pure water.

99 GENERAL AND MISCELLANEOUS↗

DOE OSTI2024

Fluid-Driven Mass Transfer During Retrograde Metamorphism and Exhumation of the UHP Western Gneiss Region Terrane, Norway

Dehydration reactions within subducted oceanic crust are important for fluid-mediated element transfer within the subducting plate and potentially to the mantle wedge. The effects of metamorphic reactions and fluid flow on element recycling that occur during retrogression and exhumation of subducted continental crust from mantle depths are poorly understood. We study two metabasite pods with fresh eclogite cores and retrogressed amphibolite-facies rims and surrounding host gneiss within the Western Gneiss Region (WGR), Norway, to better understand element mobility and mass transfer during exhumation of subducted continental crust. Bulk-rock data were collected from samples taken across the pod and into the host gneiss. Phengite breakdown in eclogite and epidote recrystallization in veins and/or gneiss within pod cores contributed large ion lithophile elements and REE to retrogressed eclogite closest to the pod cores. In gneiss hosting the pods, phengite and epidote breakdown provided fluid that mediated elemental transfer and redistribution to the pod rim or tail. Compared to the studied pod in the southern WGR, the pod in the northern WGR underwent higher P-T conditions, partial melting and higher strain rates. This resulted in the infiltration of external fluid farther into the pod interior from the rim and facilitated larger mass gain in trace elements in the amphibolite tail of the pod relative to fresh eclogite in the core. The results show clear evidence for retrogression dehydration reactions driving significant fluid-mediated element redistribution as observed on the outcrop scale during exhumation following ultrahigh-pressure metamorphism, which directly impacts element signatures within the exhuming crust.

58 GEOSCIENCES↗

DOE OSTI2022

Ion Separations Based on Spontaneously Arising Streaming Potentials in Rotating Isoporous Membranes

Highly selective ion separations are vital for producing pure salts, and membrane-based separations are promising alternatives to conventional ion-separation techniques. Our previous work demonstrated that simple pressure-driven flow through negatively charged isoporous membranes can separate Li+ and K+ with selectivities as high as 70 in dilute solutions. The separation mechanism relies on spontaneously arising streaming potentials that induce electromigration, which opposes advection and separates cations based on differences in their electrophoretic mobilities. Although the separation technique is simple, this work shows that high selectivities are possible only with careful consideration of experimental conditions including transmembrane pressure, solution ionic strength, the K+/Li+ ratio in the feed, and the extent of concentration polarization. Separations conducted with a rotating membrane show Li+/K+ selectivities as high as 150 with a 1000 rpm membrane rotation rate, but the selectivity decreases to 1.3 at 95 rpm. These results demonstrate the benefits and necessity of quantitative control of concentration polarization in highly selective separations. Increases in solution ionic strength or the K+/Li+ feed ratio can also decrease selectivities more than an order of magnitude.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2025

Ion dynamics in hexagonal boron nitride ionogel electrolytes

Ionogel electrolytes incorporating exfoliated hexagonal boron nitride (hBN) nanoplatelets are promising materials for next-generation energy storage systems. However, detailed understanding of their ion transport properties at the molecular level remains limited. This study employs diffusion and relaxation nuclear magnetic resonance (NMR) techniques, including fast-field cycling (FFC) NMR, to investigate the dynamics of ionic species in hBN-ionogels. By spanning a broad frequency range from 30 kHz using FFC NMR to high-field NMR (500–800 MHz), we reveal distinct relaxation mechanisms governing ion dynamics in ionogels with and without lithium salts. Our results highlight the role of hBN in modulating molecular rotation and translational motion, significantly affecting 1 H and 19 F relaxation profiles. The presence of Li + alters the dynamic behavior in ionogels, enhancing anion mobility at the interface. Notably, 7 Li relaxation reveals strong interactions with the hBN surface that cannot be detected by diffusion NMR. Furthermore, these findings underscore the importance of spanning a broad frequency range in NMR studies of ionogels and provide critical insights into optimizing their design as novel electrolytes.

Electrolytes↗

NASA NTRS1988

Holographic particle detection

The feasibility was studied of developing a novel particle track detector based on the detection of 1p-1s emission radiation from electron bubbles in liquid helium. The principles, design, construction, and initial testing of the detection system have been described in previous reports. The main obstacle encountered was the construction of the liquid-helium tight infrared windows. Despite numerous efforts in testing and redesigning the windows, the problem of window leakage at low temperature persisted. Due to limited time and resources, attention was switched to investigating the possibility of using room-temperature liquid as the detection medium. A possible mechanism was the detection of de-excitation radiation emitted from localized electrons in common liquids where electrons exhibit low mobilities, as suggested in the previous report. The purity of the liquid is critical in this method as the dissolved impurities (such as oxygen), even in trace amounts, will act as scavengers of electrons. Another mechanism is discussed whereby the formation of the superoxide ions by electron scavenging behavior of dissolved oxygen is exploited to detect the track of ionizing particles. An experiment to measure the ionization current produced in a liquid by a pulsed X-ray beam in order to study propertiies of the ions is also reported.

Bowen, Theodore↗