Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “high temperature superconducting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Effect of processing parameters on the characteristics of high-Tc superconductor YBa2Cu3Oy

SEM, thermogravimetric analysis, powder X-ray diffraction,and measurements of electrical resistivity and magnetic susceptibility, are presently used to characterize the influence of sintering temperature, sintering and annealing atmospheres, and quench-rate on the properties of the YBa2Cu3Oy superconducting oxide. It is established that annealing in oxygen, together with slow cooling rates, are required for preparation of high-Tc superconductors with sharp transitions; rapid quenching from high temperature does not yield good superconductors, due to low oxygen content.

Bansal, Narottam P.↗
DOE OSTI2021

Thin-film synthesis of superconductor-on-insulator A15 vanadium silicide

Abstract We present a new method for thin-film synthesis of the superconducting A15 phase of vanadium silicide with critical temperature higher than 13 K. Interdiffusion between a metallic vanadium film and the underlying silicon device layer in a silicon-on-insulator substrate, at temperatures between 650 and 750 °C, favors formation of the vanadium-rich A15 phase by limiting the supply of available silicon for the reaction. Energy dispersive X-ray spectroscopy, X-ray photoelectron spectroscopy, and X-ray diffraction verify the stoichiometry and structure of the synthesized thin films. We measure superconducting critical currents of more than 10 6 amperes per square centimeter at low temperature in micron-scale bars fabricated from the material, and an upper critical magnetic field of 20 T, from which we deduce a superconducting coherence length of 4 nm, consistent with previously reported bulk values. The relatively high critical temperature of A15 vanadium silicide is an appealing property for use in silicon-compatible quantum devices and circuits.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Thermal / structural analysis of the HB 650 thermal shield

Fermilab’s PIP-II project’s superconducting linear accelerator will drive the next generation of particle accelerators through a revolution in beam intensity. Key to beam intensification are the high efficiencies of niobium-tin superconducting radiofrequency (SRF) cavities operating at cryogenic temperatures near 5 Kelvin. A multifaceted approach is employed to achieve and maintain the extreme temperature. Vacuum provides the first barrier to thermal convection. Physical thermal intercept zones further isolate the exterior shell vacuum vessel at 300 Kelvin from the supercooled beamline. The first thermal intercept lies just inside the exterior vacuum vessel forming the 40 Kelvin zone. This 40K thermal shield is the focus of this investigation. In preparation for operation, the thermal shield is cooled from 300K to 40K in a slow process over 2-1/2 days. The factors limiting the cooling rate are a high thermal gradient which produces thermal strain and high mechanical stress. D ecreasing the time required to reach operational temperatures is the desired research goal. Physical testing data and finite element method (FEM) computer models from the Single Spoke Resonator – 1 (SSR1) and Linac Coherent Light Source (LCLS-II) cryomodules will be evaluated to determine needed design changes. The thermal shield design for the High Beta 650 MHz (HB650) will be modified and analyzed using FEM computer models to determine maximum cooling rate with a target of 50 thermal cycles of life. Maximum allowable stress will be determined through low cycle fatigue calculations.

43 PARTICLE ACCELERATORS↗
NASA NTRS1990

Low-resistance noble metal contacts to high-temperature superconductors

Low-resistance contacts were made to both YBa2Cu3O(7-x) and Bi2BaSr2Cu2O8, and to related superconducting compounds by melting gold or silver pads onto the samples before the final oxygen treatment. Scanning electron microscope studies show that both gold and silver do not diffuse far from the contact area. The surface contact resistivity of the best contacts made by the melting technique has an upper limit value in the 10 to the -8th ohm sq cm range at 77 K. This contact resistivity shows no significant change in its value over a period of 17 months. Furthermore, an electron radiation dose of 5.7 x 10 to the 17th electron/sq cm only doubled the contact resistivity.

Selim, R.↗
DOE OSTI2020

Local strain-dependent electronic structure and perpendicular magnetic anisotropy of a MnGaN 2D magnetic monolayer

Local strain-dependent spin-polarized electronic structure of a two-dimensional (2D) magnetic layer is an exciting property for practical applications. For example, it holds the promise for advanced ultrathin spintronic nanodevices with customized electronic and magnetic properties by local strain engineering. Here, we demonstrate that the spin-polarized electronic structure of a 2D manganese gallium nitride (MnGaN-2D) magnetic monolayer is sensitive to intrinsic local lattice strain, as proven by first-principles calculations and indicated by scanning tunneling spectroscopy measurements. Atomic resolution images reveal a highly non-Gaussian lattice spacing/strain distribution, while the spectroscopy reveals variations in the electronic density of states. Simulations of the MnGaN-2D monolayer based on first-principles calculations, including both isotropic and anisotropic strains, confirm a highly strain-dependent manganese partial density of states. Spin-orbit coupling is included which indicates either out-of-plane perpendicular magnetic anisotropy (PMA) or in-plane magnetic anisotropy, dependent on the type of strain whether compressive or tensile, suggesting that MnGaN-2D is magnetoelastic. The MnGaN-2D PMA is further supported by superconducting quantum interference device magnetometry measurements which reveal a high spin polarization of ~ 79 % at room temperature.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

CsV 3 Sb 5 : A $\mathbb{Z}_2$ Topological Kagome Metal with a Superconducting Ground State

Recently discovered alongside its sister compounds KV 3 Sb 5 and RbV 3 Sb 5 , CsV 3 Sb 5 crystallizes with an ideal kagome network of vanadium and antimonene layers separated by alkali metal ions. This work presents the electronic properties of CsV 3 Sb 5 , demonstrating bulk superconductivity in single crystals with a T c = 2.5 K. The normal state electronic structure is studied via angle-resolved photoemission spectroscopy and density-functional theory, which categorize CsV 3 Sb 5 as a Z 2 topological metal. Multiple protected Dirac crossings are predicted in close proximity to the Fermi level (E F ), and signatures of normal state correlation effects are also suggested by a high-temperature charge density wavelike instability. Finally, the implications for the formation of unconventional superconductivity in this material are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Measurement of 227 Ac impurity in 225 Ac using decay energy spectroscopy

225 Ac is a valuable medical radionuclide for targeted $\alpha$ therapy, but 227 Ac is an undesirable byproduct of an accelerator-based synthesis method under investigation. Sufficient detector sensitivity is critical for quantifying the trace impurity of 227 Ac, with the 227 Ac/ 225 Ac activity ratio predicted to be approximately 0.15% by end-of-bombardment (EOB). Superconducting transition edge sensor (TES) microcalorimeters offer high resolution energy spectroscopy using the normal-to-superconducting phase transition to measure small changes in temperature. By embedding 225 Ac production samples in a gold foil thermally coupled to a TES microcalorimeter we can measure the decay energies of the radionuclides embedded with high resolution and 100% detection efficiency. This technique, known as decay energy spectroscopy (DES), collapses several peaks from $\alpha$ decays into single Q-value peaks. In practice there are more complex factors in the interpretation of data using DES, which we will discuss in this paper. Using this technique we measured the EOB 227 Ac impurity to be (0.142 ± 0.005)% for a single production sample. This demonstration has shown that DES is a useful tool for quantitative measurements of complicated spectra.

07 ISOTOPE AND RADIATION SOURCES↗
DOE OSTI2023

Status of the Top Plate and Anticryostat for High Field Cable Test Facility at Fermilab

Fermi National Accelerator Laboratory (FNAL) and Lawrence Berkeley National Laboratory (LBNL) are building a new High Field Vertical Magnet Test Facility (HFVMTF) for testing superconducting cables in high magnetic field. This facility will be located at Fermilab and will have a capability similar to EDIPO at PSI and FRESCA2 at CERN. The background magnetic field of 15T in HFVMTF will be produced by a magnet pro-vided by LBNL. The HFVMTF is jointly funded by the US DOE Offices of Science, High Energy Physics, and Fusion Energy Sciences. As a primary use it will be superconducting cable test facility, in high magnetic fields and wide range of temperatures. Complementary, this facility will be used to test high-field super-conducting magnet models and demonstrators, including hybrid magnets, produced by the US Magnet Development Program (MDP). The paper describes the status of Top Plates Assembly and Sample Insert Anticryostat, which will be a main interface component between cable test mode and magnet test mode at this facility.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2023

Advancements in High-Q development for novel medium-velocity 644 MHz 5-cell elliptical superconducting RF cavities for continuous-wave operation in heavy-ion linacs

The Facility for Rare Isotope Beams is a world-leading center for experimental nuclear physics research, and relies on a first-in-kind superconducting RF driver linac to supply 400 kW beams of a uniquely large range of particles, from protons through the heaviest uranium ions. The FRIB400 project proposes to double the end energy of the current superconducting FRIB linac for the heaviest uranium ions from 200 MeV per nucleon (MeV/u) to 400 MeV/u, which equates to approximately 1 GeV for protons. The increased rare isotope production from higher-energy drive beams would deliver new and exciting capabilities to FRIB users, which include extending the facility's reach along the neutron drip-line, greatly increasing the facility's rare isotope yield, and significantly improving the precision of parameter measurements for the nuclear matter equation of state, which is a particularly timely complement to the recent advent of multi-messenger astronomy, and the study of neutron star mergers. The unique set of design parameters defined by the 400 MeV/u (uranium) energy goal, the physical size, continuous-wave operation, and cryogenic capacity of the extant facilities at FRIB, requires development of a first-in-kind beta = v/c = 0.65, 644 MHz 5-cell elliptical superconducting RF (SRF) cavity, with field-leading efficiency, measured by the cavity's intrinsic quality factor, Q_0. The field of SRF has recently experienced a very active period of development, which demonstrated the potential to raise the Q_0 of 1.3 GHz cavities by factors of two to three or more. In addition to uncovering fascinating new properties of the fundamental physics of superconducting RF phenomena, these improvements suggest substantial improvements could be made over the minimum Q_0 of the proposed FRIB400 upgrade SRF cavities, if these new techniques can be adapted to the beta = 0.65, 644 MHz regime. This work presents the first validation of the the novel beta = 0.65, 644 MHz 5-cell elliptical superconducting RF cavity design, and the first results of both conventional and advanced RF surface preparation techniques. In particular, this work focuses on two recently-developed high-Q_0 recipes: N-doping, and furnace baking, setting the current world-record Q_0 for this type of resonant cavity at 3.8 x 10^10 at the FRIB400 operating gradient of 17.5 MV/m. We also find evidence that these results may be further improved upon, and make the case for further RF surface preparation recipe optimization. We then pair these high-power RF investigations with techniques borrowed from material science to try to better understand the ways in which specific properties of the niobium material, such as grain structure and superconducting flux pinning force, can be related to its superconducting RF performance. These experiments better elucidate the effects of high-temperature annealing on niobium samples, which suggest methods of further optimizing cavity flux expulsion and thus SRF performance.Read

McGee, Kellen E.↗
NASA NTRS1994

Development of high Tc (greater than 100 K) Bi, Tl and Y-based materials as superconducting circuit elements

Experimental work on this project over the last four years has resulted in establishing processing and characterization techniques for producing both the Bi-based and Tl-based superconductors in their high temperature (2223) forms. In the bulk, dry pressed form, maximum critical temperatures (Tc) of 108.2 K and 117.8 K, respectively, were measured. Results have further shown that the Bi and Tl-based superconducting materials in bulk form are noticeably different from the Y-based 123 material in that superconductivity is considerably harder to achieve, maintain, and reproduce. This is due primarily to the difficulty in obtaining the higher Tc phase in pure form since it commonly co-exists with other undesirable, lower Tc phases. In particular, it has been found that long processing times for calcining and firing (20 - 200 hrs.) and close control of temperatures which are very near the melting point are required in order to obtain higher proportions of the desirable, high Tc (2223) phase. Thus far, the BSCCO bulk materials has been prepared in uniaxially pressed, hot pressed, and tapecast form. The uniaxially pressed material has been synthesized by the mixed oxide, coprecipitation, and melt quenching processes. The tapecast and hot pressed materials have been prepared via the mixed oxide process. In addition, thick films of BSCCO (2223 phase) have been prepared by screen printing on to yttria and magnesia stabilized zirconia with only moderate success; i.e., superconductivity was achieved in these thick films, but the highest Tc obtained in these films was 89.0 K. The Tc's of the bulk hot pressed, tapecast, and screen printed thick film materials were found to be 108.2, 102.4, and 89.0 K, respectively.

Haertling, Gene↗
NASA NTRS1990

Localization effects in radiationally disordered high-temperature superconductors: Theoretical interpretation

Theoretical interpretation of recent experiments on radiationally disordered high-temperature superconductors is presented, based on the concepts of mutual interplay of Anderson localization and superconductivity. Microscopic derivation of Ginzburg-Landau coefficients for the quasi-two-dimensional system in the vicinity of localization transition is given in the framework of the self-consistent theory of localization. The 'minimal metallic conductivity' for the quasi-two-dimensional case is enhanced due to a small overlap of electronic states on the nearest neighbor conducting planes. This leads to a stronger influence of localization effects than in ordinary (three-dimensional) superconductors. From this point of view even the initial samples of high-temperature superconductors are already very close to Anderson transition. Anomalies of H(c2) are also analyzed, explaining the upward curvature of H(c2)(T) and apparent independence of dH(c2)/dT (T = T(sub c)) on the degree of disorder as due to localization effects. Researchers discuss the possible reasons of fast T(sub c) degradation due to the enhanced Coulomb effects caused by the disorder induced decrease of localization length. The appearance and growth of localized magnetic moments is also discussed. The disorder dependence of localization length calculated from the experimental data on conductivity correlates reasonably with the theoretical criterion for suppression of superconductivity in the system with localized electronic states.

Goshchitskii, B. N.↗
DOE OSTI2026

Spin Stripes and Superconductivity in Bilayer Nickelates

The bilayer nickelate La3Ni2O7 has recently emerged as a high-temperature superconductor with unusual spin stripe order in its ambient pressure phase. We propose a microscopic Hamiltonian that faithfully reflects the crystalline symmetry of this system, with the primary aim of addressing its unconventional magnetism at ambient pressure. Using state-of-the-art density matrix renormalization group calculations, we show that (π/2,π/2) spin stripe order arises in our model at sizable Hund's coupling JH from a hidden quasi-one-dimensionality and persists over a range of electron concentrations. In the more symmetric high-pressure regime, our model exhibits enhanced interlayer pairing tendencies when the interlayer antiferromagnetic coupling J⊥ becomes sufficiently large. Our results provide a microscopic origin of the diagonal spin stripes and identify Hund's coupling JH and interlayer coupling J⊥ as key ingredients governing magnetic order and pairing tendencies in La3Ni2O7.

Wang, Hao-Xin [The Chinese University of Hong Kong↗
NASA NTRS1995

Superconducting materials processing

The effects of materials processing on the properties and behavior of high temperature yttrium barium copper oxide (YBCO) superconductors were investigated. Electrical, magnetic, and structural characteristics of thin films (300 nm) YBA2CU3O(delta) structures grown by pulsed laser deposition on LaAlO3 and SrTiO3 substrates were used to evaluate processing. Pole projection and thin film diffraction measurements were used to establish grain orientation and verify structural integrity of the samples. Susceptibility magnetization, and transport measurements were used to evaluate the magnetic and electrical transport properties of the samples. Our results verified that an unfortunate consequence of processing is inherent changes to the internal structure of the material. This effect translates into modifications in the properties of the materials, and undesired feature that makes it very difficult to consistently predict material behavior. The results show that processing evaluation must incorporate a comprehensive understanding of the properties of the materials. Future studies will emphasize microstructural characteristics of the materials, in particular, those microscopic properties that map macroscopic behavior.

Hurley, John S.↗
DOE OSTI2024

A new ductile, tougher resin for impregnation of superconducting magnets

A major remaining challenge for Nb 3 Sn high field magnets is their training due to random temperature variations in the coils. The main objective of our research is to reduce or eliminate it by finding novel impregnation materials in replacement of the epoxies currently used. An organic olefin-based thermosetting dicyclopentadiene resin, C 10 H 12 , commercially available in Japan as TELENE® by RIMTEC, was used to impregnate a short Nb 3 Sn undulator coil developed by ANL and FNAL. This magnet reached short sample limit after only two quenches, compared with ∼100 when CTD-101K® was used. Ductility, i.e. the ability to accept large strains, and toughness were identified as key properties to achieve these results. In addition, we have been investigating whether mixing TELENE with high heat capacity ceramic powders such as Gd 2 O 3 , Gd 2 O 2 S, and HoCu 2 , increases the specific heat (C p ) of impregnated Nb3Sn superconducting magnets. The viscosity, heat capacity, thermal conductivity, and other physical properties of TELENE with high-C p powder fillers were measured in this study as a function of temperature and magnetic field. The TELENE-87 wt%Gd 2 O 2 S had a peak in C p between 4.3 K and 5.3 K at fields between 0 and 8 T. We have also investigated the effect on the mechanical properties of pure and mixed TELENE under 10 MGy of gamma ray irradiation at the Takasaki Advanced Radiation Research Institute in Takasaki, Japan. TELENE-87 wt%Gd 2 O 2 S exhibited exceptional radiation resistance. Impregnating an undulator coil with TELENE mixed with Gd 2 O 2 S powder will verify whether the coils' thermal stability further improves, or whether its low diffusivity will require engineering the material with high-thermal conductivity components. Short magnet training will lead to better magnet reliability, lower magnet margins, lower risk and substantial saving in accelerators' commissioning costs. Part of this study is supported by the U.S.-Japan Science and Technology Cooperation Program in high energy physics operated by MEXT in Japan and DOE in the U.S.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2023

Low- and high-temperature heat capacity of metallic technetium

The heat capacity of technetium metal has been measured from 2.1 K to 293 K using relaxation calorimetry and the enthalpy increment up to 1700 K using drop calorimetry. The low-temperature calorimetry measurements revealed a superconducting transition temperature of T C = (7.76 ± 0.08) K. The zero-degree Debye temperature(θ E ) and the electronic heat capacity coefficient ($γ_{e}$) of the normal state were derived as (307 ± 5) K and (4.22 ± 0.20) mJ·K –2 ·mol –1 , respectively. The standard entropy of the superconducting standard state was derived as $S^{°}_{m}$ (298.15) = (36.8 ± 1.3) J·K –1 ·mol –1 . The fitting of enthalpy-increment data together with high-temperature heat capacity data reported in literature yielded a heat capacity equation up to 1700 K.

36 MATERIALS SCIENCE↗
NASA NTRS2004

Cryogenic Electric Motor Tested

Technology for pollution-free "electric flight" is being evaluated in a number of NASA Glenn Research Center programs. One approach is to drive propulsive fans or propellers with electric motors powered by fuel cells running on hydrogen. For large transport aircraft, conventional electric motors are far too heavy to be feasible. However, since hydrogen fuel would almost surely be carried as liquid, a propulsive electric motor could be cooled to near liquid hydrogen temperature (-423 F) by using the fuel for cooling before it goes to the fuel cells. Motor windings could be either superconducting or high purity normal copper or aluminum. The electrical resistance of pure metals can drop to 1/100th or less of their room-temperature resistance at liquid hydrogen temperature. In either case, super or normal, much higher current density is possible in motor windings. This leads to more compact motors that are projected to produce 20 hp/lb or more in large sizes, in comparison to on the order of 2 hp/lb for large conventional motors. High power density is the major goal. To support cryogenic motor development, we have designed and built in-house a small motor (7-in. outside diameter) for operation in liquid nitrogen.

Brown, Gerald V.↗
DOE OSTI2022

Strongly-overdoped $\mathrm{La}$ 2- $_{x}$$\mathrm{Sr}$$_{x}$$\mathrm{CuO}$ 4 : Evidence for Josephson-coupled grains of strongly-correlated superconductor

The interpretation of how superconductivity disappears in cuprates at large hole doping has been controversial. To address this issue, here we present an experimental study of single-crystal and thin film samples of La 2-x Sr x CuO 4 (LSCO) with x ≥0.25. In particular, measurements of bulk susceptibility on LSCO crystals with x = 0.25 indicate an onset of diamagnetism at T c1 =38.5 K, with a sharp transition to a phase with full bulk shielding at T c2 =18 K, independent of field direction. Strikingly, the in-plane resistivity only goes to zero at T c2 . Inelastic neutron scattering on 0.25 crystals confirms the presence of low-energy incommensurate magnetic excitations with reduced strength compared to lower doping levels. The ratio of the spin gap to T c2 is anomalously large. Our results are consistent with a theoretical prediction for strongly overdoped cuprates by Spivak, Oreto, and Kivelson, in which superconductivity initially develops within disconnected self-organized grains characterized by a reduced hole concentration, with bulk superconductivity occurring only after superconductivity is induced by proximity effect in the surrounding medium of higher hole concentration. Beyond the superconducting-to-metal transition, local differential conductance measurements on an LSCO thin film suggest that regions with pairing correlations survive, but are too dilute to support superconducting order. Future experiments will be needed to test the degree to which these results apply to overdoped cuprates in general.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Electronic spectra with paramagnon fractionalization in the single-band Hubbard model

We examine spectral properties of a recently proposed theory of the intermediate temperature pseudogap metal phase of the cuprates. We show that this theory can be obtained from the familiar paramagnon theory of nearly antiferromagnetic metals by fractionalizing the paramagnon into two “hidden” layers of S = 1 / 2 spins. The first hidden layer of spins hybridizes with the electrons as in a Kondo lattice heavy Fermi liquid, whereas the second hidden layer of spins forms a spin liquid with fractionalized spinon excitations. Here, we compute the imaginary part of the electronic self-energy induced by the spinon excitations.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗