Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “grain texture”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41
All sourcesNASA NTRSDOE OSTI
DOE OSTI2016

Texture development during rolling of α+β dual-phase ZrNb alloys - 2016-0070

The texture evolution during high-temperature rolling (800 deg. C) of two model zirconium-niobium alloys was studied using electron backscatter diffraction. The aim was to decouple the relative importance of deformation and phase transformation on the final texture in an effort to elucidate the origin of the strong α-transverse basal texture commonly found in the hot-rolled product. The analysis uses a reconstruction software based on the Burgers relation to reconstruct the high-temperature β orientations, with the indexed α as input. In the low niobium content alloy, the texture evolution of the {11 2-bar 0}<10 1-bar 0> component was consistent with deformation in both α and β phases, along with a variant selection mechanism that occurred during the β → α phase transformation. Variant selection was observed to depend on the orientation of the deformed prior β grains. In the high niobium content alloy, a lower α volume fraction during hot rolling gave rise to different β textures and promoted the formation of a Goss component. This contributed to the {11 2-bar 0} <10 1-bar 0> component upon cooling, with variant selection enhanced by anisotropic grain breakup. (authors)

36 MATERIALS SCIENCE↗
NASA NTRS1993

A comparison of FeO-rich, porphyritic olivine chondrules in unequilibrated chondrites and experimental analogues

Experimentally produced analogues of porphyritic olivine (PO) chondrules in ordinary chondrites provide an important insight into chondrule formation processes. We have studied experimental samples with PO textures grown at three different cooling rates (2, 5 and 100 C/h), and samples that have been annealed at high temperatures (1000-1200 C) subsequent to cooling. These are compared with natural chondrules of similar composition and texture from the ordinary chondrites Semarkona (LL3.0) and ALH 81251 (LL3.3). Zoning properties of olivine grains indicate that the Semarkona chondrules cooled at comparable rates to the experiments. Zoning in olivine from chondrules in ALH 81251 is not consistent with cooling alone but indicates that the chondrules underwent an annealing process. Chromium loss from olivine is very rapid during annealing and calculated diffusion coefficients for Cr in olivine are very similar to those of Fe-Mg interdiffusion coefficients under the same conditions. Annealed experimental samples contain an aluminous, low-Ca pyroxene which forms by reaction of olivine and liquid. No similar reaction texture is observed in ALH 81251 chondrules, and this may be evidence that annealing of the natural samples took place at considerably lower temperatures than the experimental analogues. The study supports the model of chondrule formation in a cool nebula and metamorphism of partly equilibrated chondrites during reheating episodes on the chondrite parent bodies.

Jones, Rhian H.↗
NASA NTRS1984

Fine-grained millimeter-sized objects in type 3 ordinary chondrites and their relation to chondrules and matrix

Fine-grained, opaque, silicate-rich matrix material, occurring as rims on chondrules and clasts, discrete clasts, and between chondrule and mineral fragments is a primitive component of chondrites and may resemble the material from which chondrules formed. To elucidate the relationship between chondrules and matrix and to help identify chondrule precursor material, the nimeralogy and bulk compositions of 30 mm-sized, fine-grained objects in Tieschitz (h3.6), Sharps (H3.4), Allan Hills A77299 (H3.7), Yamato 74191 (L3.6), Semarkona (LL3.0), and St. Mary's Co. (LL3.3) were studied. All are composed of submicron to micron sized material and may contain larger mineral fragments. Three texturally and mineralogically distinct types of objects were identified; all are minor components of the chondrites studied ( 1% except Sharps where melt-breccia-textured objects are approximately minus 1%). Bulk compositions of network and melt-breccia-textured objects define a rather narrow trend on a plot of Si/Al vs. Mg/Al, emphasizing a possible genetic relationship. Data show that Si/Mg is higher for network and melt-breccia-textured objects than for porphyritic and barred olivine chondrules. Melting in vaccuo of network-textured objects would cause a loss of Si relative to Mg (3), suggesting that material compositionally similar to fine grained objects could have been precursors to some chondrules.

Recca, S. I.↗
DOE OSTI2012

Room-temperature MBE deposition, thermoelectric properties, and advanced structural characterization of binary Bi[subscript 2]Te[subscript 3] and Sb[subscript 2]Te[subscript 3] thin films

Sb{sub 2}Te{sub 3} and Bi{sub 2}Te{sub 3} thin films were grown at room temperature on SiO{sub 2} and BaF{sub 2} substrates using molecular beam epitaxy. A layer-by-layer growth was achieved such that metallic layers of the elements with 0.2 nm thickness were deposited. The layer structure in the as-deposited films was confirmed by X-ray diffraction and was seen more clearly in Sb{sub 2}Te{sub 3} thin films. Subsequent annealing was done at 250 C for 2 h and produced the Sb{sub 2}Te{sub 3} and Bi{sub 2}Te{sub 3} crystal structure as confirmed by high-energy X-ray diffraction. This preparation process is referred to as nano-alloying and it was demonstrated to yield single-phase thin films of these compounds. In the thin films a significant texture could be identified with the crystal c axis being almost parallel to the growth direction for Sb{sub 2}Te{sub 3} and tilted by about 30{sup o} for Bi{sub 2}Te{sub 3} thin films. In-plane transport properties were measured for the annealed films at room temperature. Both films yielded a charge carrier density of about 2.6 x 10{sup 19} cm{sup -3}. The Sb{sub 2}Te{sub 3} films were p-type, had a thermopower of +130 {micro}V K{sup -1}, and surprisingly high mobilities of 402 cm{sup 2} V{sup -1} s{sup -1}. The Bi{sub 2}Te{sub 3} films were n-type, showed a thermopower of -153 {micro}V K{sup -1}, and yielded significantly smaller mobilities of 80 cm2 V{sup -1} s{sup -1}. The chemical composition and microstructure of the films were investigated by transmission electron microscopy (TEM) on cross sections of the thin films. The grain sizes were about 500 nm for the Sb{sub 2}Te{sub 3} and 250 nm for the Bi{sub 2}Te{sub 3} films. In the Bi{sub 2}Te{sub 3} thin film, energy-filtered TEM allowed to image a Bi-rich grain boundary phase, several nanometers thick. This secondary phase explains the poor mobilities of the Bi{sub 2}Te{sub 3} thin film. With these results the high potential of the nano-alloying deposition technique for growing films with a more complex layer architecture is demonstrated.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Defect features, texture and mechanical properties of friction stir welded lap joints of 2A97 Al-Li alloy thin sheets

1.4 mm 2A97 Al-Li alloy thin sheets were welded by friction stir lap welding using the stirring tools with different pin length at different rotational speeds. The influence of pin length and rotational speed on the defect features and mechanical properties of lap joints were investigated in detail. Microstructure observation shows that the hook defect geometry and size mainly varies with the pin length instead of the rotational speed. The size of hook defects on both the advancing side (AS) and the retreating side (RS) increased with increasing the pin length, leading to the effective sheet thickness decreased accordingly. Electron backscatter diffraction analysis reveals that the weld zones, especially the nugget zone (NZ), have the much lower texture intensity than the base metal. Some new texture components are formed in the thermo-mechanical affected zone (TMAZ) and the NZ of joint. Lap shear test results show that the failure load of joints generally decreases with increasing the pin length and the rotational speed. The joints failed during the lap shear tests at three locations: the lap interface, the RS of the top sheet and the AS of the bottom sheet. The fracture locations are mainly determined by the hook defects. - Highlights: • Hook defect size mainly varies with the pin length of stirring tool. • The proportion of LAGBs and substructured grains increases from NZ to TMAZ. • Weld zones, especially the NZ, have the much lower texture intensity than the BM. • Lap shear failure load and fracture location of joints is relative to the hook defects.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Long‐Term Structural Evolution of an Intercalated Layered Semiconductor

Intercalated molecules can dramatically modify the electronic band structure of layered semiconductors, significantly altering the optical properties of the material. In the layered monochalcogenide Gallium Telluride (GaTe), exposure to air induces a nearly 1 eV reduction of its band gap due to the interlayer diffusion and chemisorption of oxygen. The effect of oxygen chemisorption at the Te‐terminated surfaces on the structure of GaTe, however, is much less known. To better understand the structure–property relationship of intercalated GaTe, a systematic, long‐term, X‐ray diffraction study has been performed on GaTe exfoliated crystals exposed to ambient conditions. It is observed that the structural changes are not limited to a previously observed short‐term increase in lattice expansion. Over the course of months and even years after exfoliation, the oxygen adsorbates continue to modify the structure of GaTe, inducing significant disorder and grain reorientation. It is estimated that approximately one out of every two grains is slightly displaced by the intercalating oxygen, demonstrating a significant increase in grain mosaicity, while still maintaining the original {−2 0 1} out‐of‐plane texture. Correlating these structural transformations to observed changes in electrical and optical properties will enable capitalization of the use of adsorbates to engineer novel properties in these layered materials.

Chew, Annabel R.↗
DOE OSTI2014

Microstructure and Sn crystal orientation evolution in Sn-3.5Ag lead-free solders in high temperature packaging applications

Understanding the reliability of eutectic Sn-3.5Ag lead-free solders in high temperature packaging applications is of significant interest in power electronics for the next generation electric grid. Large area (2.5mm 2.5mm) Sn-3.5Ag solder joints between silicon dies and direct bonded copper substrates were thermally cycled between 5 C and 200 C. Sn crystal orientation and microstructure evolution during thermal cycling were characterized by electron backscatter diffraction (EBSD) in scanning electron microscope (SEM). Comparisons are made between observed initial texture and microstructure and its evolution during thermal cycling. Gradual lattice rotation and grain boundary misorientation evolution suggested the continuous recrystallization mechanism. Recrystallization behavior was correlated with dislocation slip activities.

high temperature packaging↗
DOE OSTI2014

Deformation Behavior of Solid-Solution-Strengthened Mg-9wt%Al Alloy: In-Situ Neutron Diffraction and Elastic-Viscoplastic Self-Consistent Modeling

In situ neutron diffraction and elastic viscoplastic self-consistent (EVPSC) modeling have been employed to understand the deformation mechanisms of the loading unloading process under uniaxial tension in a solid-solution-strengthened extruded Mg 9 wt.% Al alloy. The initial texture measured by neutron diffraction shows that the {00.2} basal planes in most grains are tilted around 20 30 from the extrusion axis, indicating that basal slip should be easily activated in a majority of grains under tension. Non-linear stress strain responses are observed during unloading and reloading after the material is fully plastically deformed under tension. In situ neutron diffraction measurements have also demonstrated the non-linear behavior of lattice strains during unloading and reloading, revealing that load redistribution continuously occurs between soft and hard grain orientations. The predicted macroscopic stress strain curve and the lattice strain evolution by the EVPSC model are in good agreement with the experimental data. The EVPSC model provides the relative activities of the available slip and twinning modes, as well as the elastic and plastic strains of the various grain families. It is suggested that the non-linear phenomena in the macroscopic stress strain responses and microscopic lattice strains during unloading and reloading are due to plastic deformation by the operation of basal a slip in the soft grain orientations (e.g. {10.1}, {11.2} and {10.2} grain families).

Lee, Sooyeol↗
DOE OSTI2019

Microstructure and mechanical properties of oxide dispersion strengthened FeCoNi concentrated solid solution alloys

Microstructure and mechanical properties of two kinds of oxide dispersion strengthened concentrated solid solution alloys (CSAs), FeCoNi-1.5Y 2 O 3 (FCNY) and FeCoNi-1.2Ti-1.5Y 2 O 3 (FCNTY), are studied through a comparing investigation with FeCoNi (FCN) CSAs. All these alloys are fabricated by mechanical alloying, spark plasma sintering, hot rolling and annealing treatment. For three kinds of alloys, both the as-milled powders and bulk materials are of single face-centered cubic structure. Electron backscattered diffraction results reveal that the texture transformation is suppressed during the hot rolling process because the movement of grain boundaries is hindered by the oxide particles. Compared with FCN CSAs, grains are refined by 43% and 47% for FCNY and FCNTY CSAs, respectively. Nano-sized Y 2 O 3 (monoclinic structure) and Y 2 Ti 2 O 7 (pyrochlore structure) particles are uniformly distributed in FCNY and FCNTY CSAs, respectively. Both Y2O3 and Y2Ti2O7 particles show a semi-coherent relationship with the matrix. Yield strength of FCN, FCNY and FCNTY CSAs is 559, 981 and 1050 MPa, respectively. Theoretical calculations illustrate that high strength of FCNY and FCNTY CSAs comes from refined grains and high-density nano-sized oxide particles.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Microstructure evolution and mechanical properties of nano-SiCp/AZ91 composite processed by extrusion and equal channel angular pressing (ECAP)

Nano-SiCp/AZ91 magnesium matrix composite was fabricated by stir casting. The as-cast ingots were extruded at 350 °C, then processed by equal channel angular pressing (ECAP) at various temperatures (250 °C, 300 °C and 350 °C). Grains are significantly refined after the extrusion and the ECAP. A basal fibre texture was detected by neutron diffraction after the extrusion, which inclines about 45° to the extrusion direction (ED) after the ECAP. Nano-scaled SiC particles agglomerate in the as-cast composite. After the extrusion, the agglomeration tends to form continuous or discontinuous strips along the extrusion direction. By application of the ECAP, the agglomerated SiC particles are partly dispersed and the strips formed during the extrusion tend to be thinner and broken with the increasing pass number. The yield tensile strength (YTS) and the ultimate tensile strength (UTS) of the composite are dramatically increased after the extrusion. ECAP for one pass at various temperatures further increases the strength, however, the YTS decreases with the increasing ECAP temperature and the pass number. The Orowan equations predict the maximum YTS of the composite may be up to 400 MPa providing SiC particles are homogenously distributed in the matrix. - Highlights: •Nano-scaled SiC particles were successfully added into AZ91 by stirring casting. •Agglomeration of nano-particles were improved by extrusion and ECAP. •Yield strength of the composite is 328 MPa after one pass of ECAP. •Further ECAP process with optimized parameters may fully disperse nano-particles. •Yield strength is predicted to up to 400 MPa when particles are fully dispersed.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Microstructure and microhardness of wire-based laser metal deposited AA5087 using an Ytterbium fibre laser

Highlights: • Heat conduction strongly affects the microstructural development. • Heat conduction conditions changes with increasing part height. • Anisotropic microstructural development affects the microhardness of the part. • Anisotropic mechanical properties along the structure are assumed. - Abstract: Wire-based additive manufacturing has been increasingly investigated in recent years. Although it is possible nowadays to manufacture structures that are free from inner defects such as porosity and cracks using wire and arc additive manufacturing, there is still a lack of knowledge regarding wire-based laser metal deposition of aluminium and its alloys. In order to be able to produce locally tailored part properties, it is necessary to understand the process parameter to material property relationships. Using laser energy sources, it becomes possible to analyse in detail the heat input and to observe occurring microstructural evolutions. This work includes a microstructural and mechanical characterization of an AA5087 wall structure. Detailed analyses of the chemical composition, texture, and microhardness of the structure have been performed. The microstructure contains different grain orientations as well as grain shapes and sizes along the structure, resulting in locally different material properties. The results have been analysed and discussed in reference to fundamental theories such as the Hall–Petch and Orowan mechanisms.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Micromechanical and microstructure analysis of strain-induced phenomena in ultrasonic additively-manufactured Al-6061 alloy

This work investigates the anisotropic mechanical behavior (both macro and micro) of Al6061 alloy samples manufactured using ultrasonic additive manufacturing. Samples from both sonotrode travel and vibration directions (TD and VD, respectively) were investigated in the as-built and aged (8 h at 180 °C under Argon gas) conditions. The aged VD-specimens showed appearance and propagation of Luders-like band, which did not exist in the TD-specimens, deformed at the same strain rate. X-ray diffraction, x-ray computed tomography, scanning electron microscopy, laser flash technique and in-situ loading with neutron diffraction were used to characterize the material and its hardening behavior during straining. Furthermore, aging was mainly found to lead to relaxation of stresses, induced by the build process, some decrease in yield stress, and potential secondary phase reprecipitation. Stress partitioning, revealed via in situ neutron diffraction, showed that one of grain families, (110) || tensile axis, revealed strain softening at small strain range. This texture component, (110) || tensile axis, dominated the structure of VD-specimens, and was one of key factors stimulating band appearance and propagation.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Isotopic Fingerprint of Uranium Accumulation and Redox Cycling in Floodplains of the Upper Colorado River Basin

Uranium (U) groundwater contamination is a major concern at numerous former mining and milling sites across the Upper Colorado River Basin (UCRB), USA, where U(IV)-bearing solids have accumulated within naturally reduced zones (NRZs). Understanding the processes governing U reduction and oxidation within NRZs is critical for assessing the persistence of U in groundwater. To evaluate the redox cycling of uranium, we measured the U concentrations and isotopic compositions (δ 238 U) of sediments and pore waters from four study sites across the UCRB that span a gradient in sediment texture and composition. We observe that U accumulation occurs primarily within fine-grained (low-permeability) NRZs that show active redox variations. Low-permeability NRZs display high accumulation and low export of U, with internal redox cycling of U. In contrast, within high-permeability NRZs, U is remobilized under oxidative conditions, possibly without any fractionation, and transported outside the NRZs. Finally, the low δ 238 U of sediments outside of defined NRZs suggests that these reduced zones act as additional U sources. Collectively, our results indicate that fine-grained NRZs have a greater potential to retain uranium, whereas NRZs with higher permeability may constitute a more-persistent but dilute U source.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2017

Influence of Particle Morphology on 3D Kinematic Behavior and Strain Localization of Sheared Sand

The constitutive behavior of sheared sand is highly influenced by particle morphology, gradation, mineralogy, specimen density, loading condition, stress path, and boundary conditions. The current literature lacks a three-dimensional (3D) systematic experimental study that investigates the influence of particle morphology, confining pressure, and specimen density on the failure mode of sheared sand. In this paper, surface texture, roundness, and sphericity of three uniform sands and glass beads with similar grain size were quantified by using 3D images of particles. In situ nondestructive 3D synchrotron microcomputed tomography (SMT) was used to monitor the deformation of medium-dense and very dense dry sand specimens that were tested under axisymmetric triaxial loading condition at 15 and 400 kPa confining pressures. The particles were identified and tracked in 3D as shearing progressed within the specimens, and maps of incremental particle translation and rotation were developed and used to uncover the relationship between particle morphology, specimen density, and confining pressure on the deformation and failure mode of sheared sand. This paper discusses the relationship between the failure mode and particle morphology, specimen density, and confining pressure.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2014

Effects of TiO{sub 2} addition and electron irradiation on superconducting and mechanical properties of Bi{sub 2}Sr{sub 2}CaCu{sub 2}O{sub 8} (Bi-2212) superconductor

Titanium Oxide (TiO{sub 2}) compounds having very high melting point with lower heat capacity, is an excellent candidate for reinforcement of brittle materials such as superconductor ceramics. In addition to high melting point, the TiO{sub 2} is also capable of establishing flux pinning centers in bismuth-based superconductors such as the Bi-2212. To further enhance the flux pinning properties, irradiation is one of the techniques that can be used to re-create the required point defects. In this study, the effects of TiO{sub 2} addition and electron irradiation on Bi-2212 superconductor were studied. TiO{sub 2} added Bi-2212 superconductor samples with 5%, 10% and 15% weight percentage addition respectively, were prepared using the conventional solid-state reaction method. The samples were irradiated with electron beam with radiation dose of 100 KGray. Characterization was performed by X-ray Diffraction (XRD) and Scanning Electron Microscopy (SEM). The transition temperature (T{sub c}) and the critical current density (J{sub c}) of the samples were also measured. The XRD patterns for all the samples show well-defined peaks all of which could be indexed on the basis of a Bi-2212 phase structure. In addition, the XRD patterns indicate that electron irradiation did not change the structure of Bi-2212 superconducting phase. Results of SEM micrographs show disorientation in the texture of the microstructure for samples that are subjected to electron irradiation. The grains are seen to align randomly with higher degree of orientation. With regard to TiO{sub 2} additions, only small TiO{sub 2} addition sustained the superconducting properties upon irradiation. Addition of more than 5% weight percentage of TiO{sub 2} degrades the superconducting properties of the irradiated samples. Formation of weak-links may result in higher grain boundaries orientation within the superconducting grains and thus deteriorates the inter-grains connectivity and resulted in lower T{sub c} and degradation of J{sub c}. The strength of the superconductor reduced significantly when subjected to electron irradiation.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2012

Generation and Characterization of Anisotropic Microstructures in Rare Earth-Iron-Boron Alloys

The goal of this work is to investigate methods in which anisotropy could be induced in fine-grained alloys. We have identified two general processing routes to creating a fine, textured microstructure: form an amorphous precursor and devitrify in a manner that induces texture or form the fine, textured microstructure upon cooling directly from the liquid state. Since it is possible to form significant amounts of amorphous material in RE-Fe-B alloys, texture could be induced through biasing the orientationof the crystallites upon crystallization of the amorphous material. One method of creating this bias is to form glassy material and apply uniaxial pressure during crystallization. Experiments on this are presented. All of the work presented here utilizes melt-spinning, either to create precursor material, or to achieve a desired final microstructure. To obtain greater control of the system to process these materials, a study was done on the effects of heating the wheel and modifying the wheel’s surface finish on glass formation and phase selection. The second general approach—creating the desired microstructure directly from the liquid—can be done through directional rapid solidification. In particular, alloys melt-spun at low tangential wheel speeds often display directional columnar growth through a portion of the ribbon. By refining and stabilizing the columnar growth, a highly textured fine microstructure is achieved. The effects of adding a segregating element (Ag) on the columnar growth are characterized and presented.

36 MATERIALS SCIENCE↗
NASA NTRS1976

Petrology and origin of Boulders no. 2 and no. 3, Apollo 17 Station 2

The paper presents petrographic and mineralogical data for five samples from Boulder 2 (72315, 72335, 72355, 72375, and 72395) and sample 72435 from Boulder 3 at Apollo 17 Station 2. All the samples were found to consist of a few percent megaclasts set in a fine-grained matrix, which is comprised of microclasts and a poikilitic to subophitic-textured groundmass that crystallized from a melt. The samples have similar modal mineralogies, mineral compositions, and bulk-chemical compositions.

Dymek, R. F.↗
NASA NTRS1979

The petrology of the Apollo 12 pigeonite basalt suite

A study of the petrology of the Apollo 12 pigeonite basalt samples 12011, 12043, and 12007 is presented. In this suite, the abundances of olivine and Cr-spinel decrease with increasing grain size, while the abundances of plagioclase and ilmenite increase. The petrochemical and textural variations indicate that the pigeonite basalts were derived from the olivine basalts, but the compositional gap between the olivine and pigeonite basalts indicates that they could not have crystallized together from a single, initially homogeneous magma body.

Baldridge, W. S.↗