Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “flying”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41
All sourcesNASA NTRSDOE OSTI
NASA NTRS1934

A Complete Tank Test of the Hull of the Sikorsky S-40 Flying Boat - American Clipper Class

The results of a complete test in the N.A.C.A. tank on a model of the hull of Sikorsky S-40 flying boat ('American Clipper') are reported. The test data are given in tables and curves. From these data non-dimensional coefficients are derived for use in take-off calculations and the take-off time and run for the S-40 are computed. The computed take-off time was obtained by the Sikorsky Aviation Corporation in performance tests of the actual craft.

Dawson, John R↗
NASA NTRS1935

The Effect of the Angle of Afterbody Keel on the Water Performance of a Flying-Boat Hull Model

NACA model 11-C was tested according to the general method with the angle of afterbody keel set at five different angles from 2-1/2 degrees to 9 degrees, but without changing other features of the hull. The results of the tests are expressed in curves of test data and of non-dimensional coefficients. At the depth of step used in the tests, 3.3 percent beam, the smaller angles of afterbody keel give greater load-resistance ratios at the hump speed and smaller at high speed than the larger angles of afterbody keel. Comparisons are made of the load-resistance ratios at several other points in the speed range. The effect of variation of the angle of afterbody keel upon the take-off performance of a hypothetical flying boat of 15,000 pounds gross weight having a hull of model 11-C lines is calculated, and the calculations show that the craft with the largest of the angles of afterbody keel tested, 9 degrees, takes off in the least time and distance.

Allison, John M.↗
NASA NTRS1936

Tank tests of three models of flying-boat hulls of the pointed-step type with different angles of dead rise - NACA model 35 series

The results of tank tests of three models of flying-boat hulls of the pointed-step type with different angles of dead rise are given in charts and are compared with results from tests of more conventional hulls. Increasing the angle of dead rise from 15 to 25 degrees: had little effect on the hump resistance; increased the resistance throughout the planning range; increased the best trim angle; reduced the maximum positive trimming moment required to obtain best trim angle; and had but a slight effect on the spray characteristics. For approximately the same angles of dead rise the resistance of the pointed-step hulls were considerably lower at high speeds than those of the more conventional hulls.

Dawson, John R↗
NASA NTRS1933

The Effect of Spray Strips on a Model of the P3M-1 Flying Boat Hull

This note presents the results of a series of tests made in the N.A.C.A. tank on a one-sixth full-size model of the hull and side floats of the Navy P3M-1 flying boat for the purpose of finding a method of reducing the amount of spray thrown into the propellers of this craft when taking off and landing. The model was tested without spray strips and with five different spray-strip arrangements. The best arrangement was an improvement over the bare hull with no spray strips, but the improvement was not sufficient to be satisfactory with the propellers in the designed position.

Dawson, John R↗
NASA NTRS1938

A general tank test of a model of the hull of the Pem-1 flying boat including a special working chart for the determination of hull performance

The results of a general tank test of a 1/6 full-size model of the hull of the Pem-1 flying boat (N.A.C.A. model 18) are given in non-dimensional form. In addition to the usual curves, the results are presented in a new form that makes it possible to apply them more conveniently than in the forms previously used. The resistance was compared with that of N.A.C.A. models 11-C and 26(Sikorsky S-40) and was found to be generally less than the resistance of either.

Dawson, John R↗
NASA NTRS1938

Gyroscopic Instruments for Instrument Flying

The gyroscopic instruments commonly used in instrument flying in the United States are the turn indicator, the directional gyro, the gyromagnetic compass, the gyroscopic horizon, and the automatic pilot. These instruments are described. Performance data and the method of testing in the laboratory are given for the turn indicator, the directional gyro, and the gyroscopic horizon. Apparatus for driving the instruments is discussed.

Brombacher, W G↗
NASA NTRS1938

Hydrodynamic and Aerodynamic Tests of Models of Flying-boat Hulls Designed Flow Aerodynamic Drag - NACA Models 74, 74-A, and 75

The present tests illustrate how the aerodynamic drag of a flying boat hull may be reduced by following closely the form of a low drag aerodynamic body and the manner in which the extent of the aerodynamic refinement is limited by poorer hydrodynamic performance. This limit is not sharply defined but is first evidenced by an abnormal flow of water over certain parts of the form accompanied by a sharp increase in resistance. In the case of models 74-A and 75, the resistance (sticking) occurs only at certain combinations of speed, load, and trim and can be avoided by proper control of the trim at high water speeds. Model 75 has higher water resistance at very high speeds than does model 74-A. With constant speed propellers and high takeoff speeds, it appears that the form of model 75 would give slightly better takeoff performance. Model 74-A, however, has lower aerodynamic drag than does model 75 for the same volume of hull.

Truscott, Starr↗
NASA NTRS1934

Tank tests of a family of flying-boat hulls

This report presents towing tests made in the N.A.C.A. tank of a parent form and five variations of a flying-boat hull. The beams of two of the derived forms were made the same as that of the parent and the lengths changed by increasing and decreasing the spacing of stations. The lengths of the two others of the derived forms were made the same as that of the parent while the beams were changed by increasing and decreasing the spacing of buttocks, all other widths being changed in proportion. The remaining derived form has the same length and beam as the parent, but the lines of the forebody were altered to give a planing bottom with no longitudinal curvature forward of the step. The test data were analyzed to determine the minimum resistance and the angle at which it occurs for all speeds and loads. The results of this analysis are given in the form of non dimensional curves for each model. The effect of variation in over-all size, as indicated by a "complete" test on any given hull, is pointed out. The effect of changing length alone by the spacing of buttocks, as well as the effects of the changes in length-beam ratio and longitudinal curvature that result from these operations are discussed. The difficulties encountered in interpreting test results of systematic families derived by the method used are emphasized. Further studies are suggested in which changes in the variable under consideration would not be obscured by secondary changes in other important variables.

Shoemaker, James M↗
NASA NTRS1940

A New Method of Studying the Flow of the Water Along the Bottom of a Model of a Flying-boat Hull

A new method of studying the flow of the water along the bottom of a model of a flying-boat hull is described. In this method, the model is fitted with a transparent bottom and is divided down the center line by a bulkhead. The flow is observed and photographed through one-half of the model by means of the diffused illumination from a battery of lamps contained in the other half of the model. Photographs of the flow, particularly of the changes that occur when the step ventilates, are shown. The results of the present investigation indicate that the method has considerable promise, chiefly in connection with motion-picture studies.

Ward, Kenneth E↗
NASA NTRS1942

A Comparison of the Results from General Tank Tests of 1/6- and 1/12-full-size Models of the British Singapore IIC Flying Boat

A 1/6-full-size model of the hull of the British Singapore IIC flying boat was tested in the NACA tank. The results are given in the form of charts and are compared with the results of previous tests made in the NACA tank of a 1/12-full-size model, published in NACA T.N. No. 580, and with the results of tests made in the British R.A.E. tank of another 1/6-full-size model of the same hull. When the data from the tests of the 1/6- and 1/12-full-size models were compared on the basis of Froude's law of comparison, differences were found. This fact supported the belief that the small scale of the model and the use of a model that was too small to suit the equipment of the NACA tank had caused the results of the tests of the 1/12-full-size model to be less reliable than the results of the tests of the 1/6-full-size model. The results of the tests of the two models agreed sufficiently well to show that test of a small model, if made meticulously and with suitable equipment, may give useable results, but that a larger model should be used whenever feasible. The results of the NACA tests of the 1/6-full-size model were found to be in good agreement with the R.A.E. tests of a model of the same size.

Truscott, Starr↗
NASA NTRS1952

Landing characteristics in waves of three dynamic models of flying boats

Powered models of three different flying boats were landed in oncoming waves of various heights and lengths. The effects of varying the trim at landing, the deceleration after landing, and the size of the waves were determined. Data are presented on the motions and accelerations obtained during landings in rough water.

LOADS, LANDING - IMPACT, WATER↗
NASA NTRS1956

Aerodynamic Characteristics and Flying Qualities of a Tailless Triangular-wing Airplane Configuration as Obtained from Flights of Rocket-propelled Models at Transonic and Supersonic Speeds

A flight investigation of rocket-powered models of a tailless triangular-wing airplane configuration was made through the transonic and low supersonic speed range at the Langley Pilotless Aircraft Research Station at Wallops Island, Va. An analysis of the aerodynamic coefficients, stability derivatives, and flying qualities based on the results obtained from the successful flight tests of three models is presented.

DAMPING DERIVATIVES - STABILITY↗
NASA NTRS1924

The practical difficulties of commercial flying

This paper relates some of the problems commercial aircraft companies have in attracting larger numbers of paying customers. The author discusses some remedies such as changing the public perception of flying as dangerous.

Courtney, F T↗
NASA NTRS1931

Water Pressure Distribution on a Flying Boat Hull

This is the third in a series of investigations of the water pressures on seaplane floats and hulls, and completes the present program. It consisted of determining the water pressures and accelerations on a Curtiss H-16 flying boat during landing and taxiing maneuvers in smooth and rough water.

Thompson, F L↗
NASA NTRS1935

The Effect of Spray Strips on the Take-off Performance of a Model of a Flying-Boat Hull

The effect on the take-off performance of a model of the hull of a typical flying boat, Navy PH-1, of fitting spray strips of four different widths, each at three different angles, was determined by model tests in the NACA Tank. Spray strips of widths up to 3 percent of the beam improve the general performance at speeds near the hump and reduce the spray thrown. A downward angle of 30 degrees to 45 degrees in the neighborhood of the step seems most favorable for the reduction of the spray. The spray strips have a large effect in reducing the trimming moments at speeds near the hump speed, but have little effect on them at high speeds.

Truscott, Starr↗
NASA NTRS1937

Tank Tests of NACA Model 40 Series of Hulls for Small Flying Boats and Amphibians

The NACA model 40 series of flying-boat hull models consists of 2 forebodies and 3 afterbodies combined to provide several forms suitable for use in small marine aircraft. One forebody is the usual form with hollow bow sections and the other has a bottom surface that is completely developable from bow to step. The afterbodies include a short pointed afterbody with an extension for the tail surfaces, a long afterbody similar to that of a seaplane float but long enough to carry the tail surfaces, and a third obtained by fitting a second step in the latter afterbody. The various combinations were tested in the NACA Tank by the general method over a suitable range of loadings. Fixed-trim tests were made for all speeds likely to be used and free-to-trim tests were made at low speeds to slightly beyond the hump speed. The characteristics of the hulls at best trim angles have been deduced from the data of the tests at fixed trim angles and are given in the form of nondimensional coefficients applicable to any size hull.

Parkinson, John B↗
NASA NTRS1940

The application of basic data on planing surfaces to the design of flying-boat hulls

Basic lift data on planing surfaces have been analyzed and the data applied to the design of flying-boat hulls. It is shown that a balance between air and water forces requires that the beam of the planing area bear a relation to the wing area that is determined by the lift coefficient of the wing and by the angle of dead rise in the planing surface. It is also shown that the fore-and-aft extent of the required planing area depends on the angle of dead rise. Failure to provide sufficient length of planing area appears to be the main reason for the poor water performance sometimes obtained when a large angle of dead rise is used.

Diehl, Walter S↗