Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “dynamical correlation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41
All sourcesNASA NTRSDOE OSTI
NASA NTRS2006

Stability of the Wave Bearing on an Elastic Support

Numerical computation predicts that an elastic support can substantially improve the stability of the wave bearing if the dynamic stiffness and damping of this support are in a specific range of values. To experimentally validate this prediction, the housing of a gas bearing was mounted on elastic O-rings and the threshold of sub-synchronous whirl motion was experimentally observed when the bearing runs unloaded with a rotating speed up to 30,000 RPM. The O-ring system was also dynamically characterized by measuring its stiffness and damping at various frequencies up to 500 Hz. Good correlation exists between the experimental data and numerical prediction.

Dimofte, Florin↗
NASA NTRS2009

Dynamics and Predictability of Hurricane Humberto (2007) Revealed from Ensemble Analysis and Forecasting

This study uses short-range ensemble forecasts initialized with an Ensemble-Kalman filter to study the dynamics and predictability of Hurricane Humberto, which made landfall along the Texas coast in 2007. Statistical correlation is used to determine why some ensemble members strengthen the incipient low into a hurricane and others do not. It is found that deep moisture and high convective available potential energy (CAPE) are two of the most important factors for the genesis of Humberto. Variations in CAPE result in as much difference (ensemble spread) in the final hurricane intensity as do variations in deep moisture. CAPE differences here are related to the interaction between the cyclone and a nearby front, which tends to stabilize the lower troposphere in the vicinity of the circulation center. This subsequently weakens convection and slows genesis. Eventually the wind-induced surface heat exchange mechanism and differences in landfall time result in even larger ensemble spread. 1

Sippel, Jason A.↗
NASA NTRS2013

Investigation of Control Inceptor Dynamics and Effect on Human Subject Performance

The control inceptor used in a vehicle simulation is an important part of adequately representing the dynamics of the vehicle. The inceptor characteristics are typically based on a second order spring mass damper system with damping, force gradient, breakout force, and natural frequency parameters. Changing these parameters can have a great effect on pilot control of the vehicle. A quasi transfer of training experiment was performed employing a high fidelity and a low fidelity control inceptor. A disturbance compensatory task was employed which involved a simple horizon line disturbed in roll by a sum of sinusoids presented in an out-the-window display. Vehicle dynamics were modeled as 1/s and 1/s2. The task was to maintain level flight. Twenty subjects were divided between the high and the low fidelity training groups. Each group was trained to a performance asymptote, and then transferred to the high fidelity simulation. RMS tracking error, a PSD analysis, and a workload analysis were performed to quantify the transfer of training effect. Quantitative results of the experiments show that there is no significant difference between the high and low fidelity training groups for 1/s plant dynamics. For 1/s2 plant dynamics there is a greater difference in tracking performance and PSD; and the subjects are less correlated with the input disturbance function

Stanco, Anthony A.↗
NASA NTRS2018

Space-Based Sentinels for Measurement of Infrared Cooling in the Thermosphere for Space Weather Nowcasting

Infrared radiative cooling by nitric oxide (NO) and carbon dioxide (CO2) modulates the thermosphere’s density and thermal response to geomagnetic storms. Satellite tracking and collision avoidance planning require accurate density forecasts during these events. Over the past several years, failed density forecasts have been tied to the onset of rapid and significant cooling due to production of NO and its associated radiative cooling via emission of infrared radiation at 5.3 μm. These results have been diagnosed, after the fact, through analyses of measurements of infrared cooling made by the Sounding of the Atmosphere using Broadband Emission Radiometry instrument now in orbit over 16 years on the National Aeronautics and Space Administration Thermosphere, Ionosphere, Mesosphere Energetics and Dynamics satellite. Radiative cooling rates for NO and CO2 have been further shown to be directly correlated with composition and exospheric temperature changes during geomagnetic storms. These results strongly suggest that a network of smallsats observing the infrared radiative cooling of the thermosphere could serve as space weather sentinels. These sentinels would observe and provide radiative cooling rate data in real time to generate nowcasts of density and aerodynamic drag on space vehicles. Currently, radiative cooling is not directly considered in operational space weather forecast models. In addition, recent research has shown that different geomagnetic storm types generate substantially different infrared radiative response, and hence, substantially different thermospheric density response. The ability to identify these storms, and to measure and predict the Earth’s response to them, should enable substantial improvement in thermospheric density forecasts.

Mlynczak, Martin G.↗
NASA NTRSDate not supplied

Assessment of Artemis-1 Pogo Flight Instrumentation System

As the space industry continues to strive for more efficient launch vehicles, it must relyon increasingly accurate predictive models. Verification of models typically requires physical testing. Flight data measurements offer the most real and therefore the most accurate data for model correlation. As NASA prepares for the inaugural launch of Space Launch System(SLS), Artemis-1, they must rely heavily on predictive system models to ensure flight safety.NASA has implemented a Development Flight Instrumentation (DFI) system in hopes of recovering useful flight data to aid in model correlation. Historically, some of the most important flight measurements are those that monitor the potentially destructive dynamic interaction of the structural and propellant modes – a phenomenon known as pogo. Pogo is a dynamic instability that can occur on a launch vehicle during any phase of ascent. During this investigation an end-to-end assessment of the Artemis-I Pogo-related DFI was performed to identify any obstacles inherent in the current instrumentation system which may prevent successful measurement of the data necessary to validate the current predictive fluid-structural models. Input drive signals were approximated and applied to a state-space system model to derive predicted pressure and acceleration responses. These predicted responses were then fed through a simulation of the data acquisition process in order to recover predicted measurements. Finally, a mock Flight Data Analysis (FDA) was performed to assess the ability of these measurements to meet the Flight Test Objectives(FTO).

Adam Johnson↗
NASA NTRSDate not supplied

Assessment of Artemis-1 Pogo Flight Instrumentation System

As the space industry continues to strive for more efficient launch vehicles, it must rely on increasingly accurate predictive models. Verification of models typically requires physical testing. Flight data measurements offer the most real and therefore the most accurate data for model correlation. As NASA prepares for the inaugural launch of Space Launch System (SLS), Artemis-1, they must rely heavily on predictive system models to ensure flight safety. NASA has implemented a Development Flight Instrumentation (DFI) system in hopes of recovering useful flight data to aid in model correlation. Historically, some of the most important flight measurements are those that monitor the potentially destructive dynamic interaction of the structural and propellant modes – a phenomenon known as pogo. Pogo is a dynamic instability that can occur on a launch vehicle during any phase of ascent. During this investigation an end-to-end assessment of the Artemis-I Pogo-related DFI was performed to identify any obstacles inherent in the current instrumentation system which may prevent successful measurement of the data necessary to validate the current predictive models of the Main Propulsion System (MPS). Input drive signals were approximated and applied to a system-level SLS state-space model to derive predicted pressure and acceleration responses. These predicted responses were then fed through a simulation of the data acquisition process in order to recover predicted measurements. Finally, a mock Flight Data Analysis (FDA) was performed to assess the ability of these measurements to meet the Flight Test Objectives (FTO).

Adam Johnson↗
NASA NTRS2011

Enhanced Correlation of SMART Active Flap Rotor Loads

This is a follow-on study to a 2010 correlation effort. Measured data from the SMART rotor test in the NASA Ames 40- by 80- Foot Wind Tunnel are compared with CAMRAD II calculations. As background, during the wind tunnel test, unexpectedly high inboard loads were encountered, and it was hypothesized at that time that due to changes in the flexbeams over the years, the flexbeam properties used in the analysis needed updating. Boeing Mesa, recently updated these properties. This correlation study uses the updated flexbeam properties. Compared to earlier studies, the following two enhancements are implemented: i) the inboard loads (pitchcase and flexbeam loads) correlation is included for the first time (reliable prediction of the inboard loads is a prerequisite for any future anticipated flight-testing); ii) the number of blade modes is increased to better capture the flap dynamics and the pitchcase-flexbeam dynamics. Also, aerodynamically, both the rolled-up wake model and the more complex, multiple trailer wake model are used, with the latter slightly improving the blade chordwise moment correlation. This sensitivity to the wake model indicates that CFD is needed. Three high-speed experimental cases, one uncontrolled free flap case and two commanded flap cases, are considered. The two commanded flap cases include a 2o flap deflection at 5P case and a 0o flap deflection case. For the free flap case, selected modifications to the HH-06 section flap airfoil pitching moment table are implemented. For the commanded 2o flap case, the experimental flap variation is approximately matched by increasing the analytical flap hinge stiffness. This increased flap hinge stiffness is retained for the commanded 0o flap case also, which is treated as a free flap case, but with larger flap hinge stiffness. The change in the mid-span and outboard loads correlation due to the updating of the flexbeam properties is not significant. Increasing the number of blade modes results in an effective, commanded flap hinge stiffness of 4X baseline, not 3X as reported earlier. The inboard loads correlation is reasonable, but needs further study. Overall, the free flap case correlation is reasonable, thus confirming the basic correctness of the current semi-empirical modifications; the correlation for the commanded 2o flap at 5P case and the 0o flap case is also reasonable.

Kottapalli, Sesi↗
NASA NTRS1994

A preliminary evaluation of ocean topography from the TOPEX/POSEIDON mission

We have analyzed 50 ten-day cycles of TOPEX/POSEIDON (T/P) altimeter data to evaluate the ocean dynamic topography and its temporal variations. We have employed data from both the U.S. and French altimeters along with the NASA precision orbits in this analysis. Errors in the diurnal and semidiurnal components of the Cartwright-Ray tide model have been significantly reduced using a correction developed from a combination of JGM-2 and OSU91A was employed, as well as a geoid model based solely on OSU91A. The long wavelengths of the comparisons to historical data, although geoid error still corrupts the dynamic topography for wavelengths shorter than 2500 km. The root mean square (RMS) variability is similar to previous results from Geosat, with bakground 'noise' approaching 3 cm RMS. The computed annual and semiannual variations are also similar to previous Geosat results, although the hemispheric distribution of the annual heating cycle is much better presented in the T/P results. They also compare reasonably well with the Levitus hydrographic compilation in the northern hemisphere, although the T/P variations generally have larger amplitudes. Ten-day average maps of variations in sea level compare well with simulations measurements at ocean tide gauges, with RMS differences of less than 4 cm and correlations greater than 0.6 for most of the island gauges. Time-longitude plots of these sea level variations at different latitudes in the Pacific clearly show the presence of equatorial Kelvin waves and Rossby waves, with the wave speeds agreeing well with theoretical and observed values. Measurement of variations in global sea level over cycles 2-51 have an RMS variability of 6.3 mm and a rate of change of -3.5 +/- 8 mm/yr, the uncertainty primarily due to insufficient averaging of the interannual and periodic sea level variations. These results show that the accuracy of the T/P measurements of sea level has dramatically improved over previous missions, with estimated time variable errors of 4 cm or less. Although geographically correlated orbit errors have also been reduced to the few centimeter level, further improvement in determinations of the mean dynamic topography will be difficult to obtain until a more accurate model of the marine geoid is available.

Nerem, R. S.↗
NASA NTRS1985

Development of an unsteady aerodynamics model to improve correlation of computed blade stresses with test data

A reliable rotor aeroelastic analysis operational that correctly predicts the vibration levels for a helicopter is utilized to test various unsteady aerodynamics models with the objective of improving the correlation between test and theory. This analysis called Rotor Aeroelastic Vibration (RAVIB) computer program is based on a frequency domain forced response analysis which utilizes the transfer matrix techniques to model helicopter/rotor dynamic systems of varying degrees of complexity. The results for the AH-1G helicopter rotor were compared with the flight test data during high speed operation and they indicated a reasonably good correlation for the beamwise and chordwise blade bending moments, but for torsional moments the correlation was poor. As a result, a new aerodynamics model based on unstalled synthesized data derived from the large amplitude oscillating airfoil experiments was developed and tested.

Gangwani, S. T.↗
NASA NTRS1989

An experimental and analytical investigation of the effect of spanwise curvature on wing flutter at Mach number of 0.7

An experimental and analytical study was conducted at Mach 0.7 to investigate the effects of spanwise curvature on flutter. Two series of rectangular planform wings of aspect ration 1.5 and curvature ranging from zero (uncurved) to 1.04/ft were flutter tested in the NASA Langley Transonic Dynamics Tunnel (TDT). One series consisted of models with a NACA 65 A010 airfoil section and the other of flat plate cross section models. Flutter analyses were conducted for correlation with the experimental results by using structural finite element methods to perform vibration analysis and two aerodynamic theories to obtain unsteady aerodynamic load calculations. The experimental results showed that for one series of models the flutter dynamic pressure increased significantly with curvature while for the other series of models the flutter dynamic pressure decreased with curvature. The flutter analyses, which generally predicted the experimental results, indicated that the difference in behavior of the two series of models was primarily due to differences in their structural properties.

Rivera, Jose A., Jr.↗
NASA NTRS2015

Insight into the Physical and Dynamical Processes that Control Rapid Increases in Total Flash Rate

Rapid increases in total lightning (also termed "lightning jumps") have been observed for many decades. Lightning jumps have been well correlated to severe and hazardous weather occurrence. The main focus of lightning jump work has been on the development of lightning algorithms to be used in real‐time assessment of storm intensity. However, in these studies it is typically assumed that the updraft "increases" without direct measurements of the vertical motion, or specification of which updraft characteristic actually increases (e.g., average speed, maximum speed, or convective updraft volume). Therefore, an end‐to‐end physical and dynamical basis for coupling rapid increases in total flash rate to increases in updraft speed and volume must be understood in order to ultimately relate lightning occurrence to severe storm metrics. Herein, we use polarimetric, multi‐Doppler, and lightning mapping array measurements to provide physical context as to why rapid increases in total lightning are closely tied to severe and hazardous weather.

Schultz, Christopher J.↗
NASA NTRSDate not supplied

Characterization of Structural Vibration and Acoustic Radiation with a Beam-Array Doppler Vibrometer

This paper discusses the operational principles of an assembly of two opto-electronic modules with their configurations based on a Laser-Array Doppler Vibrometer (LADV) and a Shack-Hartmann Wavefront Sensor (SHWFS). Both sensors can operate concurrently providing complementary data. While the SHWFS is a well-established system that enables low-bandwidth spatio-temporal characterization of aerodynamic turbulence, the LADV technology allows real-time detection of structural vibrations and associated acoustic radiation fields. Practical examples are shown of the instruments’ capabilities, focusing on the ability to simultaneously capture, visualize and quantitatively characterize full-field non-stationary structural dynamics and unsteady sound fields or transient flow fields around ground test facility airframe models or other structures of interest. The parallel multi-channel architecture of the LADV system enables synchronous detection and temporal correlation of indicators related to the spatio-temporal vibration of the structure under inspection. This unique feature is essential for real time detection and categorization of the structural and acoustic dynamics of transient events. For the present study, the LADV data have been successfully compared with measurements obtained with the SHWFS in the wake of a subsonic scale-model airfoil. The ability of the LADV-SHWFS coupled measurements to perform real time non-intrusive evaluation and characterization of dynamic processes at operationally relevant bandwidths should provide a deeper insight into the complex structural dynamics that contribute to radiated sound fields.

Vladimir B Markov↗
NASA NTRS2017

Computational Assessment of a 3-Stage Axial Compressor Which Provides Airflow to the NASA 11- by 11-Foot Transonic Wind Tunnel, Including Design Changes for Increased Performance

A 24 foot diameter 3-stage axial compressor powered by variable-speed induction motors provides the airflow in the closed-return 11- by 11-Foot Transonic Wind Tunnel (11-Foot TWT) Facility at NASA Ames Research Center at Moffett Field, California. The facility is part of the Unitary Plan Wind Tunnel, which was completed in 1955. Since then, upgrades made to the 11-Foot TWT such as flow conditioning devices and instrumentation have increased blockage and pressure loss in the tunnel, somewhat reducing the peak Mach number capability of the test section. Due to erosion effects on the existing aluminum alloy rotor blades, fabrication of new steel rotor blades is planned. This presents an opportunity to increase the Mach number capability of the tunnel by redesigning the compressor for increased pressure ratio. Challenging design constraints exist for any proposed design, demanding the use of the existing driveline, rotor disks, stator vanes, and hub and casing flow paths, so as to minimize cost and installation time. The current effort was undertaken to characterize the performance of the existing compressor design using available design tools and computational fluid dynamics (CFD) codes and subsequently recommend a new compressor design to achieve higher pressure ratio, which directly correlates with increased test section Mach number. The constant cross-sectional area of the compressor leads to highly diffusion factors, which presents a challenge in simulating the existing design. The CFD code APNASA was used to simulate the aerodynamic performance of the existing compressor. The simulations were compared to performance predictions from the HT0300 turbomachinery design and analysis code, and to compressor performance data taken during a 1997 facility test. It was found that the CFD simulations were sensitive to endwall leakages associated with stator buttons, and to a lesser degree, under-stator-platform flow recirculation at the hub. When stator button leakages were modeled, pumping capability increased by over 20 of pressure rise at design point due to a large reduction in aerodynamic blockage at the hub. Incorporating the stator button leakages was crucial to matching test data. Under-stator-platform flow recirculation was thought to be large due to a lack of seals. The effect of this recirculation was assessed with APNASA simulations recirculating 0.5, 1, and 2 of inlet flow about stators 1 and 2, modeled as axisymmetric mass flux boundary conditions on the hub before and after the vanes. The injection of flow ahead of the stators tended to re-energize the boundary layer and reduce hub separations, resulting in about 3 increased stall margin per 1 of inlet flow recirculated. In order to assess the value of the flow recirculation, a mixing plane simulation of the compressor which gridded the under-stator cavities was generated using the ADPAC CFD code. This simulation indicated that about 0.65 of the inlet flow is recirculated around each shrouded stator. This collective information was applied during the redesign of the compressor. A potential design was identified using HT0300 which improved overall pressure ratio by removing pre-swirl into rotor 1, replacing existing NASA 65 series rotors with double circular arc sections, and re-staggering rotors and the existing stators. The performance of the new design predicted by APNASA and HT0300 is compared to the existing design.

Turbomachinery↗
NASA NTRS2015

Correlation of Amine Swingbed On-Orbit CO2 Performance with a Hardware Independent Predictive Model

The Amine Swingbed Payload is an experimental system deployed on the International Space Station (ISS) that includes a two-bed, vacuum regenerated, amine-based carbon dioxide (CO2) removal subsystem as the principal item under investigation. The aminebased subsystem, also described previously in various publications as CAMRAS 3, was originally designed, fabricated and tested by Hamilton Sundstrand Space Systems International, Inc. (HSSSI) and delivered to NASA in November 2008. The CAMRAS 3 unit was subsequently designed into a flight payload experiment in 2010 and 2011, with flight test integration activities accomplished on-orbit between January 2012 and March 2013. Payload activation was accomplished in May 2013 followed by a 1000 hour experimental period. The experimental nature of the Payload and the interaction with the dynamic ISS environment present unique scientific and engineering challenges, in particular to the verification and validation of the expected Payload CO2 removal performance. A modeling and simulation approach that incorporates principles of chemical reaction engineering has been developed for the amine-based system to predict the dynamic cabin CO2 partial pressure with given inputs of sorbent bed size, process air flow, operating temperature, half-cycle time, CO2 generation rate, cabin volume and the magnitude of vacuum available. Simulation runs using the model to predict ambient CO2 concentrations show good correlation to on-orbit performance measurements and ISS dynamic concentrations for the assumed operating conditions. The dynamic predictive modelling could benefit operational planning to help ensure ISS CO2 concentrations are maintained below prescribed limits and for the Orion vehicle to simulate various operating conditions, scenarios and transients.

Papale, William↗
NASA NTRS1972

Improved methods of performing coherent optical correlation

Coherent optical correlators are described in which complex spatial filters are recorded by a quasi-Fourier transform method. The high-pass spatial filtering effects (due to the dynamic range of photographic films) normally encountered in Vander Lugt type complex filters are not present in this system. Experimental results for both transmittive as well as reflective objects are presented. Experiments are also performed by illuminating the object with diffused light. A correlator using paraboloidal mirror segments as the Fourier-transforming element is also described.

Husain-Abidi, A. S.↗
NASA NTRS1980

Dynamic modeling of brushless dc motors for aerospace actuation

A discrete time model for simulation of the dynamics of samarium cobalt-type permanent magnet brushless dc machines is presented. The simulation model includes modeling of the interaction between these machines and their attached power conditioners. These are transistorized conditioner units. This model is part of an overall discrete-time analysis of the dynamic performance of electromechanical actuators, which was conducted as part of prototype development of such actuators studied and built for NASA-Johnson Space Center as a prospective alternative to hydraulic actuators presently used in shuttle orbiter applications. The resulting numerical simulations of the various machine and power conditioner current and voltage waveforms gave excellent correlation to the actual waveforms collected from actual hardware experimental testing. These results, numerical and experimental, are presented here for machine motoring, regeneration and dynamic braking modes. Application of the resulting model to the determination of machine current and torque profiles during closed-loop actuator operation were also analyzed and the results are given here. These results are given in light of an overall view of the actuator system components. The applicability of this method of analysis to design optimization and trouble-shooting in such prototype development is also discussed in light of the results at hand.

Demerdash, N. A.↗
NASA NTRS2010

Method and apparatus for monitoring dynamic cardiovascular function using n-dimensional representatives of critical functions

A method, system, apparatus and device for the monitoring, diagnosis and evaluation of the state of a dynamic pulmonary system is disclosed. This method and system provides the processing means for receiving sensed and/or simulated data, converting such data into a displayable object format and displaying such objects in a manner such that the interrelationships between the respective variables can be correlated and identified by a user. This invention provides for the rapid cognitive grasp of the overall state of a pulmonary critical function with respect to a dynamic system.

Westinskow, Dwayne↗
NASA NTRS2001

Dynamical Interpolation of Mesoscale Flows in the TOPEX/Poseidon Diamond Surrounding the U.S. Joint Global Ocean Flux Study Bermuda Atlantic Time-Series Study Site

An open boundary ocean model is configured in a domain bounded by the four TOPEX/Poseidon (T/P) ground tracks surrounding the US Joint Global Ocean Flux Study Bermuda Atlantic Time-Series Study (BATS) site. This implementation facilitates prescription of model boundary conditions directly from altimetric measurements (both TIP and ERS-2). The expected error characteristics for a domain of this size with periodically updated boundary conditions are established with idealized numerical experiments using simulated data. A hindcast simulation is then constructed using actual altimetric observations during the period October 1992 through September 1998. Quantitative evaluation of the simulation suggests significant skill. The correlation coefficient between predicted sea level anomaly and ERS observations in the model interior is 0.89; that for predicted versus observed dynamic height anomaly based on hydrography at the BATS site is 0.73. Comparison with the idealized experiments suggests that the main source of error in the hindcast is temporal undersampling of the boundary conditions. The hindcast simulation described herein provides a basis for retrospective analysis of BATS observations in the context of the mesoscale eddy field.

McGillicuddy, Dennis J., Jr.↗