Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “drying methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

Tuning Organic Semiconductor Packing and Morphology through Non-equilibrium Solution Processing (Final Report)

Organic semiconductors (OSCs) are a promising candidate to produce low-cost, large area, and flexible electronics. There has previously been successful development of organic field effect transistors (OFETs), photovoltaics (OPV), and bioelectronics using OSCs. Solution processing of these materials allows for the fabrication of large-area devices in the kinetic crystallization regime. The charge transport capabilities have been shown to depend on the morphology and molecular packing of the OSC within thin films. Our hypothesis is that solution processing conditions may significantly impact OSC morphology and as a result the charge transport. Therefore, this work has focused on obtaining a fundamental understanding of the morphology and molecular packing of OSCs for optimal device performance. Through our work, we have gained a better understanding of how these structural conditions were influenced by the solution processing conditions. Our studies have led to a more systematic understanding of the various parameters that impact OSC morphology. Solution processing leads to non-equilibrium films, thus allowing for the formation of diverse morphologies that are inaccessible by other fabrication methods. Previously, our group has focused on tuning the morphology of small-molecular OSCs [53, 55-57]. However, little work had been devoted to polymer OSCs. There was a lack of detailed studies characterizing the solution-state of polymer OSCs in terms of their conformation, degree of entanglement, polymer aggregation, and chain relaxation dynamics. The solution state properties are also likely to be influenced by the rigidity and molecular weight of the polymer OSCs investigated. Thus, we have focused our attention on gaining a better insight of polymer OSC films and solution processing methods. Through this proposal, our approach is to investigate the correlation between solution-state properties and the morphology of the resulting polymer OSC films. We worked three specific aims: investigate the effects of 1) polymer OSC solution-state properties on final film morphology; 2) molecular additives on the solution-state and final film properties; 3) controlled pre-aggregation in the solution-state in the final film morphology. More rigid and planar polymer backbones should promote interchain charge transport and more efficient interchain hopping between polymer chains. Through tailoring the polymer backbone, polymer sidechains, and molecular weight, we expected the altered solution-state properties to affect the final film morphology. In addition, reducing the entanglements and promoting chain alignment will likely prevent charge carrier trapping through conformation disorders. We thus studied different mechanisms, such as molecular additives, to reduce entanglements in solution. Devices fabricated from these solutions were expected to have improved charge transport abilities. In addition to tailoring the solution-state characteristics of the polymer OSCs, we investigated the effect of solution processing methods on the molecular packing and morphology of polymer OSC films. Two main solution processing techniques, e.g., spin-coating and solution shearing, were employed to fabricate OFETs. Spin coating was employed to prepare OSC films, which produce isotropic films. This technique creates several parameters to tune such as spin coating speed, acceleration, and time. Additionally, our research group developed the solution shearing method, which consists of the solution initially sandwiched between two plates. By sliding the top plate, the solution front is exposed and drying begins. This technique allows for the creation of aligned large crystalline domains. Solution shearing consists of different processing parameters which can affect the final morphology, such as shearing speed, substrate temperature and temperature gradient, distance between both plates, and the tilt angle of the top plate. Due to the complexity of the polymer systems investigated, numerous techniques were employed to characterize the polymer OSC solution state and films. All the materials were characterized using the DOE supported synchrotron X-ray scattering facilities at the Stanford Synchrotron Radiation Lightsource (SSRL). Using grazing incidence X-ray scattering (GIXS) and Near Edge X-ray Absorption Fine Structure (NEXAFS) techniques, the crystalline structure and molecular orientations of the thin films were measured. Optical absorption (UV-Vis) spectroscopy was employed to determine the aggregation state in solution and films of the polymer systems. Polarized UV-Vis also allowed for the determination of the relative degree of polymer chain alignment for solution sheared films. Additionally, various other techniques were used to investigate other properties within the film, such as atomic force microscopy (AFM) and solution rheology. Finally, the device performance is quantified through the fabrication and characterization of OFETs, which will highlight the effects of morphology on charge transport.

36 MATERIALS SCIENCE↗

Predictions of the glass transition temperature and viscosity of organic aerosols from volatility distributions

Abstract. Volatility and viscosity are important properties of organic aerosols (OA), affecting aerosol processes such as formation, evolution, and partitioning of OA. Volatility distributions of ambient OA particles have often been measured, while viscosity measurements are scarce. We have previously developed a method to estimate the glass transition temperature (Tg) of an organic compound containing carbon, hydrogen, and oxygen. Based on analysis of over 2400 organic compounds including oxygenated organic compounds, as well as nitrogen- and sulfur-containing organic compounds, we extend this method to include nitrogen- and sulfur-containing compounds based on elemental composition. In addition, parameterizations are developed to predict Tg as a function of volatility and the atomic oxygen-to-carbon ratio based on a negative correlation between Tg and volatility. This prediction method of Tg is applied to ambient observations of volatility distributions at 11 field sites. The predicted Tg values of OA under dry conditions vary mainly from 290 to 339 K and the predicted viscosities are consistent with the results of ambient particle-phase-state measurements in the southeastern US and the Amazonian rain forest. Reducing the uncertainties in measured volatility distributions would improve predictions of viscosity, especially at low relative humidity. We also predict the Tg of OA components identified via positive matrix factorization of aerosol mass spectrometer (AMS) data. The predicted viscosity of oxidized OA is consistent with previously reported viscosity of secondary organic aerosols (SOA) derived from α-pinene, toluene, isoprene epoxydiol (IEPOX), and diesel fuel. Comparison of the predicted viscosity based on the observed volatility distributions with the viscosity simulated by a chemical transport model implies that missing low volatility compounds in a global model can lead to underestimation of OA viscosity at some sites. The relation between volatility and viscosity can be applied in the molecular corridor or volatility basis set approaches to improve OA simulations in chemical transport models by consideration of effects of particle viscosity in OA formation and evolution.

54 ENVIRONMENTAL SCIENCES↗

Methods and systems for electroless plating a first metal onto a second metal in a molten salt bath, and surface pretreatments therefore

Systems and methods for electroless plating a first metal onto a second metal in a molten salt bath including: a bath vessel holding a dry salt mixture including a dry salt medium and a dry salt medium of the first metal, and without the reductant therein, the dry salt mixture configured to be heated to form a molten salt bath; and the second metal is configured to be disposed in the molten salt bath and receive a pure coating of the first metal thereon by electroless plating in the molten salt bath, wherein the second metal is more electronegative than the first metal.

Freiderich, Melissa Ensor↗

Methods and systems for electroless plating a first metal onto a second metal in a molten salt bath, and surface pretreatments therefore

Systems and methods for electroless plating a first metal onto a second metal in a molten salt bath including: a bath vessel holding a dry salt mixture including a dry salt medium and a dry salt medium of the first metal, and without the reductant therein, the dry salt mixture configured to be heated to form a molten salt bath; and the second metal is configured to be disposed in the molten salt bath and receive a pure coating of the first metal thereon by electroless plating in the molten salt bath, wherein the second metal is more electronegative than the first metal.

Freiderich, Melissa Ensor↗

Investigation of Imaging Spent Nuclear Fuel Dry Casks using Cosmic Ray Muons

Recently, the use of cosmic ray muons for cargo scanning applications has been demonstrated and muons have been shown to have the potential to allow for nondestructive assessment of nuclear material accountancy. Relativistic muons have the ability to penetrate dense materials and monitoring the subsequent scattering of muons can provide information about the structure and composition of materials stored in cargo containers. The suitability of cosmic muons for a number of monitoring and imaging applications has been investigated over the years and includes applications to archaeology, volcano imaging, material identification and medical diagnosis. Novel applications of cosmic ray muons have been proposed for examination of comatose patients towards bone density monitoring and also for determination of the molten nuclear fuel location in nuclear reactors having suffered from the effects of a severe accident similar to the one happened in Fukushima. There is a need to develop a capability to monitor nuclear waste and investigate whether the stored content agrees with facility declarations to allow proliferation detection and international treaty verification. Monitoring nuclear waste and controlling nuclear material at its source is one of the main strategies to minimize the risks of nuclear proliferation and reduce potential homeland threats. Since the early 1950's, when the first nuclear power plant began to produce electricity, approximately 65,000 metric tons of spent nuclear fuel have been generated, 25% of which are under dry storage conditions. After the spent nuclear fuel has been placed inside the dry cask, the cask is welded, not allowing for visual inspection. During the long storage life of the cask, intermediate handling and transportation activities take place which does create concerns regarding fuel integrity. Accidents and natural disasters also contribute to this concern. Previous work on spent nuclear fuel dry cask monitoring using muons has shown that the muon scattering distributions are adequately separated and a and a decision rule derived from Bayes' Theorem rendering the classification of different dry casks feasible. Muons present significant advantages over the existing imaging techniques such as the utilization of the passive nature of muons, the lack of radiological sources and consequently the absence of any artificial radiological dose. In the present work, a methodology is developed to demonstrate the applicability of muons for imaging of spent nuclear fuel dry casks. Purpose is to use muons to differentiate between spent nuclear fuel dry casks with different amounts of loading. Monte Carlo simulations of dry casks with different spent nuclear fuel loading are performed to simulate the passage of polyenergetic muons having energies in the range of 1-60 GeV through matter. A 'Muon Generator' is developed to generate muons that follow the actual sea level energy distribution. The 'Muon Generator' is validated against a series of actual spectrum measurements and then coupled with the Monte Carlo particle transport code GEANT4. The accumulated dataset of scattering angles were processed with the Point-of- the-Closest-Approach (PoCA) imaging algorithm and the obtained images demonstrate that an empty dry cask can be clearly distinguished from a half-loaded or a fully loaded one. The apparent separation of the images demonstrates that the muon scattering can be used as a feature for imaging spent nuclear fuel dry casks. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Optimization of Interlayer/CrWN Bilayer Films Fabricated and Monitored under Shewhart Control

Chromium tungsten nitride (CrWN) films were deposited onto SUS 304 stainless steel, cutter inserts and glass substrates using direct current reactive magnetron sputtering, with pure W and Cr metal targets. The deposition parameters for the interlayer (W and WN) with multiple qualities were optimized using the gray Taguchi method. The microstructure of these coatings was determined using x-ray diffraction, scanning electron microscopy, energy dispersive spectroscopy and transmission electron microscopy. The results showed that the mechanical properties of bilayer samples with an interlayer of WN nitride film are superior to those with a W metal interlayer. Moreover, increasing the N{sub 2}/(N{sub 2} + Ar) flow ratio and working pressure enhanced the microhardness and the elastic recovery for coatings with an interlayer/CrWN bilayer. Dry milling tests also showed that bilayer film coatings have better mechanical performance. This increase in multiple performance characteristics is attributed to a bilayer that is manufactured using the gray Taguchi method. Control charts, which are powerful tools and widely used, were employed to monitor and ensure high-quality fabrication of the interlayer/CrWN bilayer and to show the coating processes to be stable and well regulated.

36 MATERIALS SCIENCE↗

Enhancing physicochemical, bioactive, and nutritional properties of sweet potatoes: Ultrasonic contact drying with slot jet nozzles compared to hot-air drying and freeze drying

Sweet potatoes are a rich source of nutrients and bioactive compounds, but their quality can be impacted by the drying process. This study investigates the impact of slot jet reattachment (SJR) nozzle and ultrasound (US) combined drying (SJR + US) on sweet potato quality, compared to freeze-drying (FD), SJR drying, and hot air drying (HAD). SJR + US drying at 50 °C closely resembled FD in enhancing quality attributes and outperformed HAD and SJR in key areas such as rehydration, shrinkage ratios, and nutritional composition. Notably, SJR + US at 50 °C produced the highest total starch (36.84 g/100 g), total dietary fiber (8.48 g/100 g), total phenolic content (158.19 mg GAE/100 g), total flavonoid content (119.08 mg QE/g), DPPH antioxidant activity (6.44 μmol TE/g), β-carotene (31.98 mg/100 g), and vitamin C (5.27 mg/100 g). It also exhibited higher glass transition temperatures (Tg: 14.49 °C), indicating better stability at room temperature. The hardness values for SJR + US samples were similar to FD, while HAD samples had the highest hardness. SJR + US at 50 °C resulted in the lowest total color changes (ΔE), indicating minimal impact on appearance. Additionally, FTIR analysis revealed that peaks in specific spectral regions indicated superior preservation of bioactive compounds in SJR + US samples compared to other methods, which was also confirmed by principal component analysis (PCA) and heatmap visualization. Overall, these findings suggest that SJR + US is an effective alternative to conventional drying techniques, significantly improving the quality of dried sweet potatoes.

Color↗

Measurement of specimen dimensions and dynamic pressure in dynamic triaxial experiments

Novel experimental techniques are developed to measure the rapid changes in specimen dimensions during dynamic triaxial experiments. A capacitance gage is designed and constructed to measure the diameter change of the specimen inside the pressure chamber at both low and high rates. The length change is determined by a linear variable differential transformer at low rates and by Kolsky bar signals at high rates. The Kolsky bar also measures the dynamic axial stress in the specimen during the high-rate phase of an experiment. A line pressure gage records the hydrostatic pressure in the chamber. The dynamic pressure variation in the chamber during axial impact loading is detected by a manganin gage placed inside the chamber. The feasibility of this new experimental setup is demonstrated by dynamic triaxial experiments on a fine dry sand.

42 ENGINEERING↗

Synthesis, spinning, and properties of very high molecular weight poly(acrylonitrile- co -methyl acrylate) for high performance precursors for carbon fiber

In this paper, synthesis of very high molecular weight (VHMW) polyacrylonitrile- co -methyl acrylate(PAN-co-MA) polymers with weight average molecular weights of at least 1.7 million g/mole were repeatedly achieved on a laboratory scale using emulsion polymerization. Furthermore, the development of a hybrid dry-jet gel solution spinning technique for the VHMW PAN-co-MA enabled continuous spinning of 100 filament count tows, 100s of meters in length. Single filaments were analyzed and tested for tensile performance. Experimentally, the hybrid spinning method coupled with VHMW polymers produced precursor fibers with excellent tensile properties, averaging 954 MPa in strength and 15.9 GPa in elastic modulus ( N = 296), with small filament diameters (5 μm). Results indicate a strong correlation between decreasing filament diameter, facilitated by high molecular weight polymer, and exponentially increasing tensile properties, using a hybrid dry-jet gel spinning process.

36 MATERIALS SCIENCE↗

Extreme Ultraviolet and Beyond Extreme Ultraviolet Lithography Using Amorphous Zeolitic Imidazolate Resists Deposited by Atomic/Molecular Layer Deposition

Amorphous zinc-imidazolate (aZnMIm) resists show potential to meet the demands for next-generation high-numerical aperture (high-NA) metal-containing extreme ultraviolet (EUV) resist materials, given their ease of deposition by atomic/molecular layer deposition (ALD/MLD) at thicknesses of 20 nm and below. Here, this study demonstrates that aZnMIm thin films, previously identified as high-resolution electron beam resists, can also function as negative-tone EUV photoresists. Water development achieves high sensitivity (5 mJ/cm 2 ) but leaves significant residue, while acetic acid development results in poor contrast. A hybrid approach─water followed by acetic acid─enables residue-free development with a sensitivity of 181 mJ/cm 2 . Dry development using 1,1,1,5,5,5-hexafluoroacetylacetone (hfacH) is also possible but shows lower sensitivity (375 mJ/cm 2 ) compared to wet development methods. EUV photoelectron spectroscopy (PES), reflectometry/EUV absorption, total electron yield (TEY), residual gas analysis (RGA), and time-of-flight secondary ion mass spectrometry (TOF-SIMS) were used to investigate the effects of EUV irradiation on aZnMIm resists. Reflectometry experiments reveal an aZnMIm EUV absorption coefficient of 6.2 μm –1 , while PES and TEY analyses show that, compared to poly(4-hydroxystyrene) (PHS), a polymer-based reference resist, aZnMIm emits more primary and secondary electrons but generates fewer slow electrons relative to its primary electron emission; its total electron yield is similar to that of poly(methyl methacrylate) (PMMA) resists. When exposed to EUV, aZnMIm predominantly outgasses H 2 , as determined by RGA. TOF-SIMS measurements demonstrate that high-dose EUV exposure only partially fragments the 2-methylimidazole (2MIm) organic linkers, unlike high-dose electron beam exposure, which is known to completely degrade them. Additionally, aZnMIm resists show promise for potential beyond EUV lithography (BEUVL) due to the presence of Zn, which provides higher sensitivity at a wavelength of 6.7 nm compared to other metal ions, such as Sn, that are currently used in the best-performing EUV metal–organic resists. TEY measurements demonstrate that aZnMIm emits nearly twice as many electrons as PHS at 6.7 nm. The BEUV TEY of aZnMIm also surpasses that of PMMA, poly(pentafluorostyrene), and poly(4-iodostyrene), with the latter two being known for their high EUV TEYs. This work provides insight into zeolitic imidazolate framework (ZIF)-based EUV and BEUV resists and highlights their potential for both wet and dry development.

lithography↗

Multi-scale integration of satellite remote sensing improves characterization of dry-season green-up in an Amazon tropical evergreen forest

In tropical forests, leaf phenology-particularly the pronounced dry-season green-up-strongly regulates biogeochemical cycles of carbon and water fluxes. However, uncertainties remain in the understanding of tropical forest leaf phenology at different spatial scales. Phenocams accurately characterize leaf phenology at the crown and ecosystem scales but are limited to a few sites and time spans of a few years. Time-series satellite observations might fill this gap, but the commonly used satellites (e.g. MODIS, Landsat and Sentinel-2) have resolutions too coarse to characterize single crowns. To resolve this observational challenge, we used the PlanetScope constellation with a 3m resolution and near daily nadir-view coverage. We first developed a rigorous method to cross-calibrate PlanetScope surface reflectance using daily BRDF-adjusted MODIS as the reference. We then used linear spectral unmixing of calibrated PlanetScope to obtain dry-season change in the fractional cover of green vegetation (GV) and non-photosynthetic vegetation (NPV) at the PlanetScope pixel level. We used the Central Amazon Tapajos National Forest k67 site, as all necessary data (from field to phenocam and satellite observations) was available. For this proof of concept, we chose a set of 22 dates of PlanetScope measurements in 2018 and 16 in 2019, all from the six drier months of the year to provide the highest possible cloud-free temporal resolution. Our results show that MODIS-calibrated dry-season PlanetScope data (1) accurately assessed seasonal changes in ecosystem-scale and crown-scale spectral reflectance; (2) detected an increase in ecosystem-scale GV fraction (and a decrease in NPV fraction) from June to November of both years, consistent with local phenocam observations with R 2 around 0.8; and (3) monitored large seasonal trend variability in crown-scale NPV fraction. Finally, our results highlight the potential of integrating multi-scale satellite observations to extend fine-scale leaf phenology monitoring beyond the spatial limits of phenocams.

54 ENVIRONMENTAL SCIENCES↗

Spectral analysis of amazon canopy phenology during the dry season using a tower hyperspectral camera and modis observations

The association between spectral reflectance and canopy processes remains challenging for quantifying large-scale canopy phenological cycles in tropical forests. In this paper, we used a tower-mounted hyperspectral camera in an eastern Amazon forest to assess how canopy spectral signals of three species are linked with phenological processes in the 2012 dry season. We explored different approaches to disentangle the spectral components of canopy phenology processes and analyze their variations over time using 17 images acquired by the camera. The methods included linear spectral mixture analysis (SMA); principal component analysis (PCA); continuum removal (CR); and first-order derivative analysis. In addition, three vegetation indices potentially sensitive to leaf flushing, leaf loss and leaf area index (LAI) were calculated: the Enhanced Vegetation Index (EVI), Normalized Difference Vegetation Index (NDVI) and the entitled Green-Red Normalized Difference (GRND) index. We inspected also the consistency of the camera observations using Moderate Resolution Imaging Spectroradiometer (MODIS) and available phenological data on new leaf production and LAI of young, mature and old leaves simulated by a leaf demography-ontogeny model. The results showed a diversity of phenological responses during the 2012 dry season with related changes in canopy structure and greenness values. Because of the differences in timing and intensity of leaf flushing and leaf shedding, Erisma uncinatum, Manilkara huberi and Chamaecrista xinguensis presented different green vegetation (GV) and non-photosynthetic vegetation (NPV) SMA fractions; distinct PCA scores; changes in depth, width and area of the 681-nm chlorophyll absorption band; and variations over time in the EVI, GRND and NDVI. At the end of dry season, GV increased for Erisma uncinatum, while NPV increased for Chamaecrista xinguensis. For Manilkara huberi, the NPV first increased in the beginning of August and then decreased toward September with new foliage. Variations in red-edge position were not statistically significant between the species and across dates at the 95% confidence level. The camera data were affected by view-illumination effects, which reduced the SMA shade fraction over time. When MODIS data were corrected for these effects using the Multi-Angle Implementation of Atmospheric Correction Algorithm (MAIAC), we observed an EVI increase toward September that closely tracked the modeled LAI of mature leaves (3–5 months). Compared to the EVI, the GRND was a better indicator of leaf flushing because the modeled production of new leaves peaked in August and then declined in September following the GRND closely. Finally, while the EVI was more related to changes in mature leaf area, the GRND was more associated with new leaf flushing.

54 ENVIRONMENTAL SCIENCES↗

Water vapor exposure chamber for constant humidity and hydrogen and oxygen stable isotope composition

Rationale: Water vapor exposure experiments have applications for studying water physisorption and chemisorption hydration and hydroxylation reactions on a wide variety of material surfaces. The stable isotopes of hydrogen and oxygen in the water molecule are useful tracers of water exchange mechanisms and/or rates in such vapor exposure experiments. Methods: We designed and built a humidity chamber system that uses membrane-mediated liquid–vapor exchange of water followed by mixing with dry air to control the relative humidity of air and its δ 2 H and δ 18 O isotopic composition. We tested the stability and precision of the humidity and its isotopic composition on hourly to 90-day timescales. Results: The humidity chamber design reported here is capable of providing relative humidity control to within ±1%, and consistent δ 2 H and δ 18 O values of the water vapor that are similar to our cavity ringdown spectroscopy (CRDS) measurement precision (δ2H vap ± 0.7‰ and δ18O vap ± 0.24‰). We quantify the isotopic enrichment effects of Rayleigh distillation in the system and provide information on water reservoir sizes large enough to buffer isotopic enrichment effects to within measurement precision. Conclusions: The humidity chamber design reported here provides a means to create constant δ2H and δ18O values over the course of an exposure experiment. The design has applications to a wide range of studies of water sorption on material surfaces from foods and pharmaceuticals to geological materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of surface hydroxyl groups on heat capacity of mesoporous silica

This paper quantifies the effect of surface hydroxyl groups on the effective specific and volumetric heat capacities of mesoporous silica. To achieve a wide range of structural diversity, mesoporous silica samples were synthesized by various methods, including (i) polymer-templated nanoparticle-based powders, (ii) polymer-templated sol-gel powders, and (iii) ambigel silica samples dried by solvent exchange at room temperature. Their effective specific heat capacity, specific surface area, and porosity were measured using differential scanning calorimetry and low-temperature nitrogen adsorption-desorption measurements. The experimentally measured specific heat capacity was larger than the conventional weight-fraction-weighted specific heat capacity of the air and silica constituents. The difference was attributed to the presence of OH groups in the large internal surface area. A thermodynamic model was developed based on surface energy considerations to account for the effect of surface OH groups on the specific and volumetric heat capacity. The model predictions fell within the experimental uncertainty.

Marszewski, Michal↗

Submicron Thickness Characterization of Poly-Si Thin Films on Textured Surfaces by X-Ray Diffraction for Minimizing Parasitic Absorption in Poly-Si/SiO2 Passivating Contact Cells

Poly-Si/SiO2 passivating contacts have shown great potential for industry-relevant next-generation solar cells. Previous work has demonstrated an improved Jsc from dry reactive ion etching in an SF6 environment, using front metal grids as a self-aligned mask. Here, we show an effective method to measure the front poly-Si thickness on an alkaline textured surface using X-ray diffraction. The calculated thicknesses are compared with cross-section SEM analysis and Quokka simulation. We show that by thinning the front poly-Si from 200 nm to 60 nm, Jsc increases by 2.4 mA/cm2, leading to an absolute efficiency gain of 1.73%. Finally, we discuss possible reasons for the premature loss of passivation before the removal of all poly-Si.

41 EE - Solar Energy Technologies Office (EE-4S)↗

Optimization of a High Pressure Turbine Blade and Sector-Based Annular Rig Design for Supercritical CO2 Power Cycle Representative Testing

Abstract As part of the ongoing research into the design of hardware for zero emission cycles, a first-stage high-pressure turbine (HPT) blade is optimized for a 300 MWe supercritical CO2 (sCO2) power cycle using the surrogate-assisted genetic algorithm optimizer in Numeca FINE/Design three-dimensional with objectives of increasing efficiency and decreasing heat load to the blade. Supercritical CO2 property tables are constructed from NIST REFPROP data for the condensable gas simulation in FINE/Turbo. A detailed mesh sensitivity study is performed for a baseline design to identify the proper-grid refinement and efficiently allocate resources for the optimization. Seventy design variables are selected for the initial population generation. Self-organizing maps are then used to focus the design variables on the most important ones affecting the objective functions. The optimization results in approximately 3000 three-dimensional Reynolds Averaged Navier Stokes simulations of different blade shapes with increases in efficiency of up to 0.85% and decreases in heat load of 14%. Families of blade shapes are identified for experimental testing in an annular rig at the Purdue Experimental Turbine Aerothermal Laboratory. A design to adapt the annular cascade for testing optimized geometries is introduced, which features eccentric radius sectors allowing for scaled-up geometries of sCO2 optimized blade profiles to be tested at design cycle representative conditions at high Reynolds numbers in dry air. Analysis into the effects of Reynolds number, working fluid, and geometric relations are presented to prove the efficacy of the test method.

Engineering↗

Neutron Measurements from Boron Carbide Addition to a Plutonium Waste Form

The Department of Energy (DOE) has identified the Dilute and Dispose approach as the preferred method for the disposition of surplus plutonium materials. Dilute and Dispose requires surplus plutonium to be converted to an oxide product and then dry blended with a multi-component adulterant mixture to reduce the Safeguards and Security attractiveness level of the materials. The resulting product will be discarded in a geologic repository at the Waste Isolation Pilot Plant (WIPP).

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Sol-Gel Based Nanoparticles for 3D Printing of Optical Glass

Additive manufacturing also known as 3D printing provides an innovative way to produce gradient index (GRIN) lens and other high-performance optics. Novel inks for direct ink write (DIW) 3D printed optical glass have been reported; however, the refractive index has never surpassed a value of 1.48. Here, we report a ternary formulation of core-shell SiO 2 nanoparticles coated with a TiO 2 shell and GeO 2 nanoparticles that can be used as a feedstock for DIW lenses. Printable titanium-germanium-silica inks were prepared from colloidal sol-gel feed stocks to produce shear-thinning inks for DIW. The inks were dried and sintered following an optimized heat treatment to remove organic material and produce a transparent and void-free monolith. Through this method, we found that these lenses are transparent at dopant concentrations of 7 mol% TiO 2 and 14 mol% GeO 2 . With higher dopant concentrations of germanium and titanium, these lenses subsequently have a refractive index of 1.52. Moreover, these inks share the same viscoelastic properties as previous shear thinning DIW inks, allowing these inks to be 3D printed.

36 MATERIALS SCIENCE↗