Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “drying”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Effect of hydration on morphology of thin phosphonate block copolymer electrolyte membranes studied by electron tomography

The morphological changes of phosphonate polypeptoid electrolyte membranes, poly-N-(2-ethyl)hexylglycine-block-poly-N-phosphonomethylglycine (pNeh m -b-pNpm n ), in hydrated and dry states were characterized by cryogenic transmission electron microscopy (cryo-TEM) and cryogenic electron tomography (cryo-ET). The analysis of 3D tomograms revealed that the pNeh 9 -b-pNpm 9 thin films absorbed a large amount of water, resulting in the formation of membranes that were nearly flat and giant multicompartment vesicles dispersed in the water phase. A simple lamellar phase appeared when the films were dried. In contrast, pNeh 18 -b-pNpm 18 thin films absorbed little water and formed small highly curved unilamellar and multilamellar vesicles. Water was located mainly outside the closely-packed vesicles. When water was removed by drying, the walls of adjacent vesicles collapsed to form honeycomb-like capsules. Here, the changes in domain size reflected changes in chain conformations. The pNpm9 blocks were saturated by water and fully extended, while pNpm 18 blocks were neither saturated by water nor fully extended. In addition, the thicknesses of hydrophobic blocks in the hydrated films of both pNeh 9 -b-pNpm 9 and pNeh 18 -b-pNpm 18 were smaller than those in the dry films, reflecting an increase of the average distance between the neighboring junctions of polypeptoid molecules.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Elucidating Pore Network Evolution in Laboratory‐ and Shaft‐Furnace Hydrogen‐Reduced Iron Pellets Using Nanotomographic Characterization

Direct reduced iron (DRI) is an increasingly important feedstock for modern steelmaking. Fundamental research into DRI properties is limited by the discrepancy between the behavior of industrially produced pellets and laboratory‐produced pellets, leading to nongeneralizable conclusions from laboratory work. Here, in this study, a detailed nano‐computed tomographic characterization of ore pellets, hydrogen DRI reduced in a pilot‐scale shaft furnace, and laboratory‐reduced DRI is presented to better understand the microstructurally influenced property differences between the two. The shaft‐furnace‐reduced pellets show lower overall porosity but larger average pore volume thickness and solid volume thickness than the laboratory‐reduced pellets. This effect is attributed to increased sintering behavior in the shaft furnace case. All pellet types show almost entirely connected pore volumes. The tortuosity of the pores is shown to increase with a degree of reduction, though the shaft furnace pellets show lower tortuosity than the laboratory‐reduced pellets. Again, this difference is attributed to the larger pore volume thickness for shaft‐furnace‐reduced pellets.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Projected future daily characteristics of African precipitation based on global (CMIP5, CMIP6) and regional (CORDEX, CORDEX-CORE) climate models

In this work, we provide an assessment of future daily characteristics of African precipitation by explicitly comparing the results of large ensembles of global (CMIP5, CMIP6) and regional (CORDEX, CORE) climate models, specifically highlighting the similarities and inconsistencies between them. Results for seasonal mean precipitation are not always consistent amongst ensembles: in particular, global models tend to project a wetter future compared to regional models, especially over the Eastern Sahel, Central and East Africa. However, results for other precipitation characteristics are more consistent. In general, all ensembles project an increase in maximum precipitation intensity during the wet season over all regions and emission scenarios (except the West Sahel for CORE) and a decrease in precipitation frequency (under the Representative Concentration Pathways RCP8.5) especially over the West Sahel, the Atlas region, southern central Africa, East Africa and southern Africa. Depending on the season, the length of dry spells is projected to increase consistently by all ensembles and for most (if not all) models over southern Africa, the Ethiopian highlands and the Atlas region. Discrepancies exist between global and regional models on the projected change in precipitation characteristics over specific regions and seasons. For instance, over the Eastern Sahel in July–August most global models show an increase in precipitation frequency but regional models project a robust decrease. Global and regional models also project an opposite sign in the change of the length of dry spells. CORE results show a marked drying over the regions affected by the West Africa monsoon throughout the year, accompanied by a decrease in mean precipitation intensity between May and July that is not present in the other ensembles. This enhanced drying may be related to specific physical mechanisms that are better resolved by the higher resolution models and highlights the importance of a process-based evaluation of the mechanisms controlling precipitation over the region.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Carbon content of soil fractions varies with season, rainfall, and soil fertility across a lowland tropical moist forest gradient

Tropical forests contain some of the largest soil carbon (C) stocks on Earth, making them broadly relevant to terrestrial-climate feedbacks, yet our understanding of how their soil organic C (SOC) fractions vary over space and time is limited. We studied effects of season, fertility, and mean annual precipitation (MAP) on the C contents of soil fractions across 14 lowland forests in Panama. We measured free-debris, occluded-debris, and mineral-associated SOC fractions, as well as soluble C associated with each fraction. We hypothesized that mineral-associated SOC would be greatest in infertile, strongly weathered soils with large reactive mineral contents. We also hypothesized that the debris SOC fractions would accumulate during the dry season, reflecting seasonal increases in litterfall. To address this, we compared soil fractions in wet and dry seasons from fertile and infertile soils across a range of 1809 – 2864 mm MAP. The C content (mg C / g soil) of all soil fractions varied with fertility and MAP: specifically, free-debris SOC was greatest in wet, high-fertility soils, and occluded-debris SOC was greater in high-fertility than low-fertility soils. The mineral-associated SOC fraction, which contained the majority of bulk soil C, showed increasing C content with greater MAP in infertile sites, presumably driving similar spatial patterns in the bulk soil. Only the free-debris SOC fraction showed strong seasonal variation, increasing in mass during the dry season. Nitrogen behaved similarly to C. In summary, soil C contents increased with MAP in infertile sites but not fertile sites, driven by the mineral-associated SOC fraction. The dry season had greater free-debris SOC, but this seasonal trend was not apparent in bulk soil C, likely because of the small size of the free-debris SOC fraction. Furthermore, changes in the quantity and seasonality of precipitation, which are projected for tropical forests, might shift spatial and temporal patterns of soil C storage, which would in turn influence forest-climate feedbacks for this C-rich biome.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Effects of a Pressurized Water Treatment on Internal Gelation Sol-Gel Microspheres

Based on previous observations that a pressurized water treatment (PWT) prevented cracking of sol-gel microspheres, we investigated the effects of a PWT on microsphere crystallinity, density, and specific surface area (SSA). Results were used to determine how a PWT alters the properties of microspheres upon drying and heating. Microspheres with diameters near 100-200 µm were prepared with and without a PWT and measured using x-ray diffraction (XRD), transmission electron microscopy (TEM), nitrogen adsorption (BET), and pycnometry. Properties of air-dried microspheres processed with and without a PWT are compared. Additionally, the properties of microspheres processed using a PWT are reported after heating to 150 °C, 450 °C, 750 °C, 1050 °C, and 1350 °C. X-ray diffraction measurements indicate that the PWT step improves the crystallinity of air-dried microspheres. XRD data was also used to calculate crystallite size, which increases with higher heat treatment temperatures. TEM images support crystallite size calculations from XRD data and provide an indication of the range of crystallite sizes, particularly for samples processed at higher temperatures where crystallite sizes are too large for estimation using the Scherrer formula. Density and SSA measurements performed as a function of heat treatment temperature indicate that a PWT increases the density of air-dried microspheres, creates a pore network, and that significant densification occurs between 450 - 750 °C. These results may be used to inform decisions on internal gelation flowsheet parameters to optimize the microsphere formation and gelation step, prevent microsphere cracking, and produce microspheres suitable for subsequent coating operations or pressing into pellets.

cerium oxide, TRISO, internal gelation, nuclear fu↗
DOE OSTI2025

Evaluation of desiccation cracking characteristics of inorganic micro-fiber-reinforced engineered barrier material (IMEBM) for geological repository

Abstract Buffer material is crucial for the engineering barrier system to dispose of high-level radioactive waste in a geological repository. A reliable buffer material should be able to maintain good sealing characteristics and minimize desiccation cracking. In this study, the effectiveness of inorganic fiber-reinforced engineering barrier material in reducing desiccation cracks in bentonite was evaluated via desiccation tests, image analysis, and air permeability tests. The effects of fiber type (E-glass fiber and basalt fiber) and fiber content (0.0%, 0.5%, 1.0%, 1.5%, 3.0%, and 5.0% of dry weight of the bentonite) on the development of desiccation cracks in the fiber–bentonite mixtures with the same given initial moisture content were evaluated. The results indicated that the addition of fibers could significantly reduce the crack size and area in bentonite during the drying. Basalt fibers showed a slightly better reinforcement effect than E-glass fibers when the fiber content was lower than 3.0%. The addition of fibers prevented the development of penetrating cracks and significantly reduced the permeability of the bentonite after drying. The permeabilities of basalt fiber- and E-glass fiber-reinforced bentonite composites with 3% reinforcement were 5.81 × 10 –11 m 2 and 7.24 × 10 –11 m 2 , respectively, which were 64 and 51 times smaller than that of pure bentonite. X-ray–CT observation of the internal structure of the samples after drying showed that the addition of fibers significantly changed the crack morphology and potentially increased the tortuosity.

Feng, Yuan↗
DOE OSTI2021

Shrinkage-induced deformations and creep of structural concrete: 1-year measurements and numerical prediction

Highlights: • Extensive experimental study on drying shrinkage, creep and microcracking of concrete • All specimens prepared from a single batch of ordinary-strength structural concrete • 1st year of measurements of (not only) non-uniformly drying beams with span up to 3-m • The database is downloadable from free-to-use research data repository • Modified MPS model for concrete creep used in blind prediction of all experiments The material models for creep and shrinkage operating on the material point level in FEM are usually intended for challenging complex applications and structures, where the average cross-sectional approach does not suffice. The identification of the growing number of material parameters induced by increasing model capabilities relies on very specific and narrow-oriented yet interconnected experiments which are scarce. The presented comprehensive experiments aim to provide a clearer image of the complicated interaction among the basic phenomena: drying, shrinkage, creep, and microcracking. The cornerstone of this ongoing research is a unique set of 30 partially-sealed unreinforced concrete beams with span 1.75–3.0 m subjected to drying. To minimize material variation, all specimens in this study were cast from a single batch of ordinary strength structural concrete with slag-blended binder. The resulting experimental database will be suitable both for validation and development of the constitutive models.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Physical and chemical effects of isopropanol exchange in cement-based materials

Drying cement-based materials is a necessary step to characterize the microstructure by microscopy, adsorption, or mercury intrusion. The isopropanol (IPA) exchange method is commonly used to replace the pore solution prior to drying, as it reduces the capillary pressure and thereby helps to preserve the microstructure of the hydrated cementitious materials. However, some physical and chemical effects of IPA on hydration products have been reported. These effects cannot be completely avoided, but can be reduced by shortening the exchange duration, in particular for effects on ettringite. This study carried out experiments with different exchange durations and IPA removal techniques to address research gaps in the literature. For 1-mm cubes of cement paste with IPA diffusion coefficient of 1 × 10{sup −11} m{sup 2}/s, the compared exchange durations are 5 min, 15 min (value from the literature), 40 min (when the mixture at the sample center achieves 95% of the drop in surface tension from water to IPA), 80 min (when the IPA/water mixture at the sample center reaches an azeotrope), 5 h (when over 99% IPA is replaced at the sample center), and 24 h (prolonged exchange). After IPA exchange, samples were either directly dried at 40 °C with flushing N{sub 2} or washed by diethyl ether prior to N{sub 2} drying. Even though the exchange duration of 40 and 80 min, in theory, can reduce the damage from capillary pressure, the nitrogen adsorption results do not show any advantage in preventing microstructural alteration. The 5-h exchange provided results similar to the 24-h exchange, but the latter induced slightly more serious chemical effects resulting from the longer contact of IPA with hydration products. In addition, the compared IPA removal techniques do not show significant differences. Therefore, this study suggests using small samples (~1 mm) for microstructural studies following IPA exchange for a period corresponding to the time when 99% of the water (mole fraction) at the sample center is replaced.

36 MATERIALS SCIENCE↗
DOE OSTI2026

A Generalized Grain-Scale Model for the Non-Plasma and Plasma-Assisted Hydrogen Direct Reduction of Iron Ore

Direct Reduction of Iron ore using hydrogen (H-DRI) is a promising pathway towards efficient steelmaking and accurate predictive models are a necessity for scale-up and optimization of this technology. However, accurate models of this process remain limited because existing models oversimplify grain-scale phenomena, such as nonlinearity inside grain, self-sufficient porosity, surface reactions, and the role of plasma species. These phenomena are important for flash steelmaking and plasma-assisted H-DRI processes. To address this need, we present a phenomenological model for simulating H-DRI at the scale of a single micron-sized grain of the iron ore. We call this the Transient Reactive Grain Model (TRGM). TRGM incorporates key physical process: gas species transport, a chemical kinetics of material conversion, nanopore structural evolution and, adsorption-desorption surface kinetics at the reactive nanopore surface. The important contribution of this work is that the model provides a dependence on different reductant species, specifically hydrogen atoms versus molecules, so that role of hydrogen plasma reduction can be clarified compared to the use of pure hydrogen gas reduction. TRGM predictions agree well with experimental data for both molecular H2 reduction of Fe2O3 and plasma hydrogen reduction of Fe3O4. Results reveal species concentration gradients with a diffuse reaction zone, and enhanced hydrogen diffusion at the grain outer surface due to evolving porosity. These findings challenge common assumptions in existing models, including sharp reaction fronts, quasi-steady diffusion and kinetics, and the neglect of surface chemistry. As a generalized grain-scale model for H-DRI processes, TRGM has practical applications in flash steelmaking and in-flight reduction using both molecular and plasma hydrogen.

08 HYDROGEN↗
DOE OSTI2025

Laboratory evaluation of cyclic underground hydrogen storage in the Temblor sandstone of the San Joaquin Basin, California

Underground Hydrogen Storage (UHS) in depleted oil and gas reservoirs could provide a cost-effective solution to balance seasonal fluctuations in renewable energy generation. However, data and knowledge on UHS at subsurface conditions are limited so it is difficult to estimate how effective this type of storage could be. In this study, we perform high pressure experiment to measure the effectiveness of cyclic hydrogen (H 2 ) storage in a specimen of Temblor sandstone retrieved from the San Joaquin Basin of California. Our experiment mimics reservoir pressure conditions to measure H 2 -brine relative permeability and fluid-rock interactions over the course of ten charging and discharging cycles. Initial gas breakthrough occurred at 15 % to 25 % H2 saturation in the specimen with 3 % NaCl brine as the resident fluid. Continuing injecting to 4 pore volumes (PV) of H 2 yielded an asymptotic H 2 saturation of 38 % to 41 %, a level often referred to as the irreducible gas saturation based on two-phase flow. The boundary condition in this study mimics the near wellbore region, which experiences bi-directional H 2 flow. This bi-directional flow led to evaporative drying of the specimen resulting in 94 % H 2 saturation at the end of 10th cycle. This indicates that cyclic flow and evaporative drying can lead to more efficient reservoir storage where a larger fraction of the reservoir porosity is usable to store H 2 . The produced gas stream consisted of H 2 mixed with 8 % to 22 % H 2 O, indicating formation dry-out by evaporation. Meanwhile, produced water chemistry indicated calcite and silicate dissolution, with calcite sourced from fossil fragments. This led to a loss of cementation and weakened the rock sample. Combined, our results indicate dry-out, compaction, increased H 2 saturation, rock weakening, and permeability loss during cyclic UHS. Overall, we anticipate that the combined effects should lead to higher than anticipated UHS storage efficiency per volume of sandstone reservoir rock.

08 HYDROGEN↗
DOE OSTI2023

Effect of initial water saturation on the performance of fracturing fluids with and without polyallylamine under simulated EGS conditions

Objectives/Scope: StimuFrac (US Patents 9,873,828 B2 and 9,447,315 B2), a CO 2 - reactive polymer aqueous solution [polyallylamine (PAA) 1wt% in water] combined with CO 2 , can be used as a potentially less water-intensive fracturing fluid for enhanced geothermal systems (EGS). Our previous results show that in hot dry rock (HDR), PAA/CO 2 fracturing fluids outperformed other fluids such as water, CO 2 , and CO 2 /water in generating large fractures with less fluid consumed. The objective of this work is to investigate the effect of initial water saturation on the performance of StimuFrac by conducting hydraulic fracturing tests with ½ foot cubic rock samples held under representative EGS stress/temperature conditions and by using cyclic injection strategies (under constant injection rate). The resulting fracture hydraulic conductivities, breakdown pressures, and volumes of fluids required are compared. Methods/Procedures/Process: To simulate geothermal reservoir conditions, in all tests, the rock sample was held under triaxial confinement and at 200 °C, and different volumes of water were initially injected into the rock sample before any fracturing processes were initiated. For the single-cycle PAA (or water) alternating CO 2 (PAG or WAG) injection fracturing experiments, one complete cycle consisted of two steps: (1) injecting a PAA slug (or water slug) followed by (2) injecting CO 2 to initiate and propagate the fracture. For experiments involving multiple injection cycles, the CO 2 injection pressure is increased until it peaks and begins to decline (indicating fracture initiation at this moment), and then continued being injected for another 30 seconds to propagate the fracture. Then, these two-step cycles [injection of PAA (or water) followed by CO 2 injection (up to 2-4 mL/min)] are repeated. Applications/Significance/Novelty: The results of this study suggest that water saturation significantly affects the fracturing fluid transmission into the rock pore space, thus affecting the fracture initiation and propagation. In this study, fracturing tests via a single injection cycle or multiple injection cycles were performed. Splitting the rock samples in half after testing reveals that fracture propagation is significantly limited under high water saturation conditions (three-day initial water injection) compared to stimulation experiments performed in hot dry rock. The fractures propagate less than 1/3 of the distance from the wellbore to the outer rock surface, and in some cases, no fracture is generated. This may be caused by leak-off dominating the fracturing process and the fluid injection rate is insufficient to overcome leak-off, even under high injection rate conditions. Additionally, CO 2 could be leaking off into the wellbore annulus and this may be making it more difficult to generate sufficiently high-pressure gradients away from the near-wellbore region. Under low water saturation conditions (dry rock or after 1-day initial water injection), PAA/CO 2 consistently generated significantly larger fractures compared with the other fluids. CO 2 generated large fractures only in the hot dry rock and only when using high injection rates, though data variability is high.

58 GEOSCIENCES↗
DOE OSTI2021

Transparent silica aerogel slabs synthesized from nanoparticle colloidal suspensions at near ambient conditions on omniphobic liquid substrates

This paper presents a novel sol-gel method to synthesize large and thick silica aerogel monoliths at near ambient conditions using a commercial aqueous solution of colloidal silica nanoparticles as building blocks. To achieve slabs with high visible transmittance and low thermal conductivity, the method combines the strategies of (i) synthesizing gels on an omniphobic perfluorocarbon liquid substrate, (ii) aging at temperatures above room temperature, and (iii) performing solvent exchange with a low-surface-tension organic solvent prior to ambient drying. The omniphobic liquid substrates were used to prevent cracking and ensure an optically-smooth surface, while nanoparticle building blocks were small (<10 nm) to limit volumetric light scattering. Gels were aged at temperatures between 25 and 80 °C for up to 21 days to make them stronger and stiffer and to reduce shrinkage and cracking during ambient drying. Ambient drying was achieved by first exchanging water in the gel pores for octane, followed by drying in an octane-rich atmosphere to decrease capillary forces. The synthesized nanoparticle-based silica aerogel monoliths had thicknesses up to 5 mm, diameters up to 10 cm, porosities exceeding 80%, and thermal conductivities as low as 0.08 W m –1 K –1 . Notably, the slabs featured visible transmittance exceeding 75% even for slabs as thick as 5 mm. The as-synthesized aerogel monoliths were exposed to TMCS vapor to induce hydrophobic properties resulting in a water contact angle of 140° that prevented water infiltration into the pores and protected the aerogels from water damage. This simple synthesis route conducted at near ambient conditions produces hydrophobic aerogel monoliths with promising optically transparent and thermally insulating properties that can be adhered to glass panes for window insulation and solar-thermal energy conversion applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Electrochemical, thermodynamic, and physical properties of tetradecyltrihexylphosphonium ([P 6,6, 6,14 ] + ) and methyl-propyl piperidinium containing ionic liquids and their propylene carbonate solutions

Here, the viscosity, conductivity, electrochemical window and related thermodynamic properties such as excess volume and dynamic viscosity deviation of two phosphonium ionic liquids were measured and calculated for “as-supplied” and dried neat liquids and also v/v mixtures of 99/1, 95/5, 90/10, 75/25, and 50/50 of the ionic liquids with propylene carbonate (PC). Tetradecyltrihexylphosphonium dicyanamide ([P 6,6,6,14 ] + dicyanamide), Cyphos 105, and tetradecyltrihexylphosphonium bis(trifluororomethanesulfonyl)imide (called bistriflimide) ([P 6,6,6,14 ] + bistriflimide), Cyphos 109, ionic liquids were studied. Generally speaking, there were slight differences in the measured properties of the wet and dried IL solutions which were reflected in differences if the calculated properties. The measured and calculated properties were compared with those collected and derived from a piperidinium-based ionic liquid, methyl-propyl piperidinium bistriflimide. Arrhenius plots for both the viscosity and conductivity were linear, with the linearity of the Litovitz plots being slightly higher. The viscosity and conductivity of the phosphonium solutions yielded Walden Plots that differed from Walden plots of piperidinium solutions and other ionic liquid solutions. For the phosphonium based ionic liquids, the ionicity was found to increase with increasing dilution in propylene carbonate. The electrochemical windows of the ionic liquids were determined as a function of the concentration of the ionic liquid present in the solution. The size of the window generally initially decreased and then increased with the addition of PC for the [P 6,6,6,14 ] + dicyanamide ionic liquid increasing from 3.4 V in the 95/5 v/v (volume Cyphos 105) to volume of PC solvent) to 3.7 in the 50/50 dried IL case. The electrochemical windows of the dried liquids were slightly larger 3.5 V for the 95/5 v/v and 4.2 V for the 50/50 v/v Cyphos 105/PC solutions. The electrochemical window was larger and the conductivity was higher for the piperidinium IL solutions, but since the ionicity increases with dilution, the phosphonium based IL solutions may prove favorable for processes such as electrochemical reduction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Accumulation of microplastics in soil after long-term application of biosolids and atmospheric deposition

Land-applied biosolids can be a considerable source of microplastics in soils. Previous studies reported microplastics accumulation in soils from biosolid application, however, little is known about the contribution of atmospherically deposited microplastics to agricultural soils. In this study, we quantified and characterized microplastics in soils that have been amended with biosolids over the past 23 years. We also collected atmospheric deposition samples to determine the amount and type of plastics added to soils through atmospheric input over a period of about 2 years. Soil samples were taken from a replicated field trial where biosolids have been applied at rates of 0, 4.8, 6.9, and 9.0 t/ha every second crop. The biosolids were anaerobically digested and dewatered, and were applied by spreading onto the soil surface. Soil and atmospheric samples were extracted for microplastics by Fenton's reaction to remove organic matter followed by flotation in a zinc chloride solution to separate plastic from soil particles. Samples were analyzed for microplastics by optical microscopy and Laser Direct Infrared Imaging Analysis (LDIR). The mean number of microplastics identified from biosolids samples was 12,000 particles/kg dry biosolids. The long-term applications of biosolids to the soil led to mean plastics concentrations of 383, 500, and 361 particles/kg dry soil in the 0–10 cm depth for low, medium, and high biosolids application rates, respectively. These plastic concentrations were not significantly different from each other, but significantly higher than those found in non biosolids-amended soil (117 particles/kg dry soil). The dominant plastic types by number found in biosolids were polyurethane, followed by polyethylene, and polyamide. The most abundant plastics in soil samples were polyurethane, polyethylene terephthalate, polyamide, and polyethylene. Atmospheric deposition contributed to 15 particles/kg dry soil per year and was mainly composed of polyamide fibers. In conclusion, this study shows that long-term application of biosolids led to an accumulation of microplastics in soil, but that atmospheric deposition also contributes a considerable input of microplastics.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Importance of the Heat Treatment Scheme on Self-Reducing Reactive Silver Inks

Self-reducing reactive silver inks can print high-quality silver at reasonable temperatures. While numerous studies have explored the impact of processing temperature on electrical properties, the role of the heat treatment scheme has not yet been studied. Common heat treatment schemes include printing and drying inks at room temperature before heat treatment, performing heat treatments while the inks are still wet, and directly printing the inks onto heated substrates. Each scheme generates distinct heat transfer and mass transport kinetics that can affect the silver morphology and electrical properties. However, to date, the impact of different schemes has not been systematically investigated. To address this knowledge gap, this work investigates how different heat treatment schemes impact metal formation, sintering, and the resultant electrical properties of printed self-reducing reactive silver inks. Heat treatment on room-temperature dried inks and wet inks, with top-down (oven) and bottom-up (hot plate) heating sources, were compared. Inks dried at room temperature resulted in extremely porous films that required high heat treatment temperatures (>100 °C) for silver densification. However, these dried films could only densify locally, and their high initial porosities resulted in voids and high resistances (~0.6 Ω mm –1 ) even after heat treatments above 300 °C. Inks that were wet during heat treatment showed moderate improvements in electrical properties with resistances on the order of 0.4 Ω mm –1 at heat treatments of 250 °C. Printing reactive inks directly onto heated substrates yielded the best low-temperature results, with 0.46 Ω mm –1 (5.5 × bulk silver) line resistances achieved at only 90 °C. Overall, this work’s experimental results provide detailed insights into why printing onto a heated substrate results in superior electrical performance compared to more common heat treatment schemes. Additionally, controlling where the precipitation reaction occurs is critical to controlling the film morphology and properties. As a result, this work shows that even an ammonia-based silver reactive ink can achieve good, low-temperature electrical properties with the proper heat treatment scheme.

14 SOLAR ENERGY↗
DOE OSTI2024

Life-Cycle Assessment of Sustainable Aviation Fuel Derived from Paper Sludge

Converting waste paper sludge to sustainable aviation fuel (SAF) offers a circular economy strategy to decarbonize the aviation sector. Here, this study develops a life-cycle assessment (LCA) for converting high-ash paper sludge to SAF in the U.S. using a catalytic sugar upgrading system that consists of ash removal, enzymatic hydrolysis, dehydration, aldol condensation, and hydroprocessing. The LCA is coupled with a process simulation for an industrial-scale biorefinery based on experimental data. We quantified the carbon intensity as 35.7–41.8 gCO 2 eq MJ –1 SAF (–636 to –584 gCO 2 eq per dry kg paper sludge) with acetone as a solvent, renewable fuel, and biobased chemicals; this is further reduced to 5.1–11.1 gCO 2 eq MJ –1 (–925 to –873 gCO 2 eq per dry kg paper sludge) if ash is recycled and used for substituting cement. Converting 1 dry kg paper sludge to SAF with acetone, renewable fuel, and biobased chemicals (–925 to –584 gCO 2 eq) is more climate beneficial than landfilling without landfill gas recovery (791 gCO 2 eq) and with landfill gas recovery (–294 gCO 2 eq). More than 330 million gallons of SAF can be produced annually (>4 million dry t paper sludge/year in the U.S.), resulting in a reduction of 2–7 million tCO 2 eq.

09 BIOMASS FUELS↗
DOE OSTI2021

A Retrospective and Prospective Examination of the 1960s U.S. Northeast Drought

As the most severe drought over the Northeastern United States (NEUS) in the past century, the 1960s drought had pronounced socioeconomic impacts. Although it was followed by a persisting wet period, the conditions leading to the 1960s extreme drought could return in the future, along with its challenges to water management. To project the potential consequences of such a future drought, pseudo-global warming simulations using the Weather Research and Forecasting Model are performed to simulate the dynamical conditions of the historical 1960s drought, but with modified thermodynamic conditions under the shared socioeconomic pathway SSP585 scenario in the early (2021–2027), middle (2041–2047), and late (2091–2097) 21st century. Our analysis focuses on essential hydroclimatic variables including temperature, precipitation, evapotranspiration, soil moisture, snowpack, and surface runoff. In contrast to the historical 1960s drought, similar dynamical conditions will generally produce more precipitation, increased soil moisture and evapotranspiration, and reduced snowpack. However, we also find that although wet months get much wetter, dry months may become drier, meaning that wetting trends are most significant in wet months but are essentially negligible for extremely dry months with negative monthly mean net precipitation. For these months, the trend toward wetting conditions provides little relief from the effects of extreme dry months. These conditions may even aggravate water shortages due to an increasingly rapid transition from wet to dry conditions. Other challenges emerge for residents and stakeholders in this region, including more extreme hot days, record-low snow pack, frozen ground degradation and subsequent decreases in surface runoff.

54 ENVIRONMENTAL SCIENCES↗