Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “drawing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

Evaluation of additive manufacturing side channels for nuclear nonproliferation applications

The nuclear industry is continuing to grow and adopt new technologies to manufacture components. One of the technologies under consideration is additive manufacturing (AM). AM could make production of components at lower cost and could lessen lead times significantly. However, AM could be prone to proliferation risks. AM machines give off signatures during the manufacturing process, and these signatures offer an alternative means of observing the component. Correlations between these signatures and the geometry being manufactured could be developed; enabling proliferators as they could take advantage of these correlations to steal AM manufacturing instructions relating to nuclear technology. This work pertains to preliminary work exploring the feasibility of tapping into AM side channels to predict geometries being manufactured on AM machines. The feasibility of utilizing vibration to draw geometric correlations will be assessed on an Ultimaker 2 + thermoplastic 3D printer.

Additive manufacturing↗

Computer Modeling and Simulation: Increasing Reliability by Disentangling Verification and Validation

Verification and validation (V&V) of computer codes and models used in simulations are two aspects of the scientific practice of high importance that recently have been discussed widely by philosophers of science. While verification is predominantly associated with the correctness of the way a model is represented by a computer code or algorithm, validation more often refers to the model’s relation to the real world and its intended use. Because complex simulations are generally opaque to a practitioner, the Duhem problem can arise with verification and validation due to their entanglement; such an entanglement makes it impossible to distinguish whether a coding error or the model’s general inadequacy to its target should be blamed in the case of a failure. I argue that a clear distinction between computer modeling and simulation has to be made to disentangle verification and validation. Drawing on that distinction, I suggest to associate modeling with verification and simulation, which shares common epistemic strategies with experimentation, with validation. To explain the reasons for their entanglement in practice, I propose a Weberian ideal–typical model of modeling and simulation as roles in practice. I examine an approach to mitigate the Duhem problem for verification and validation that is generally applicable in practice and is based on differences in epistemic strategies and scopes. Based on this analysis, I suggest two strategies to increase the reliability of simulation results, namely, avoiding alterations of verified models at the validation stage as well as performing simulations of the same target system using two or more different models. In response to Winsberg’s claim that verification and validation are entangled I argue that deploying the methodology proposed in this work it is possible to mitigate inseparability of V&V in many if not all domains where modeling and simulation are used.

97 MATHEMATICS AND COMPUTING↗

Climate adaptation heuristics and the science/policy divide

The adaptation science enterprise has expanded rapidly in recent years, presumably in response to growth in demand for knowledge that can facilitate adaptation policy and practice. However, evidence suggests such investments in adaptation science have not necessarily translated into adaptation implementation. One potential constraint on adaptation may be the underlying heuristics that are used as the foundation for both adaptation research and practice. In this paper, we explore the adaptation academic literature with the objective of identifying adaptation heuristics, assessing the extent to which they have become entrenched within the adaptation discourse, and discussing potential weaknesses in their framing that could undermine adaptation efforts. This investigation is supported by a multi-method analysis that includes both a quantitative content analysis of the adaptation literature that evidences the use of adaptation heuristics and a qualitative analysis of the implications of such heuristics for enhancing or hindering the implementation of adaptation. Results demonstrate that a number of heuristic devices are commonly used in both the peer-reviewed adaptation literature as well as within grey literature designed to inform adaptation practitioners. Furthermore, the apparent lack of critical reflection upon the robustness of these heuristics for diverse contexts may contribute to potential cognitive bias with respect to the framing of adaptation by both researchers and practitioners. Finally, we discuss this phenomenon by drawing upon heuristic-analytic theory, which has explanatory utility in understanding both the origins of such heuristics as well as the measures that can be pursued toward the co-generation of more robust approaches to adaptation problem-solving.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Root size and soil physicochemical properties drive microscale spatial patterns of Fe and As retention in the rice rhizosphere

Background and Aims: Radial oxygen loss from rice roots in flooded soils oxidizes and precipitates dissolved Fe(II), Mn(II), and As(III) into mixed Fe(III), Mn(III/IV), and As(V) as root plaque and in the rhizosphere soil. It is unknown how different soils and root sizes impact the spatial extent of Fe and As retention outside the root. Methods: We imaged cross-sections of 90 roots from 6 different soils using synchrotron μXRF imaging followed by k-means clustering and elliptical averaging to distinguish bulk soil, rhizosphere, plaque, and roots based on As and Fe patterns. Results: We found preferential As retention in the plaque and rhizospheres of most roots except small (< 0.45 mm) roots in silty soils with low P or high As. In contrast, clayey soils had similar As-Fe correlations across plaque, rhizosphere, and bulk soil. Large (> 0.45 mm) roots often had no oxidized rhizosphere region. We obtained an extensive dataset of 256 As and 155 Mn synchrotron μXANES measurements, which revealed that rhizosphere and plaque As was mainly inorganic As(V) and As(III), and Mn oxidation state varied between soils but not between belowground locations. Conclusion: Small roots in coarse-textured soils were less likely to have As retention in the plaque or rhizosphere compared to large roots and fine-textured soils. Furthermore, the unique and extensive data in this study provides new insight into soil and root size impacts on As retention in the rhizosphere. It is essential to investigate a representative number of samples to draw conclusions from XRF imaging.

36 MATERIALS SCIENCE↗

New titanium(IV) coordination compounds with 2-hydroxybenzyl alcohol derivatives used in the preparation of ultra-high molecular weight polyethylene

A reaction of 2,4-bis(α,α-dimethylbenzyl)phenol with TiCl{sub 2}(ОPr{sup i})2 and Ti(ОPr{sup i}){sub 4} was used to obtain the coordination compounds (HL){sub 2}L{sub 2}Ti{sub 2}Cl{sub 2}•MeC{sub 6}H{sub 5} and L{sub 4}Ti{sub 4}(OPr{sup i}){sub 8}, respectively. The compounds were characterized by elemental analysis, NMR spectroscopy, and X-ray diffraction. The titanium(IV) coordination compounds obtained polymerize ethylene in the presence of binary cocatalysts {3Et_2AlCl + Bu_2Mg} or {3Et_3Al_2Cl_3 + Bu_2Mg} at moderate to high rates, giving rise to ultra-high molecular weight polyethylene with a wide range of molecular masses. The highest values of tensile strength (2.4 GPa) and modulus of elasticity (ε = 2.67%) were obtained for the sample with a molecular mass of 3.14•10{sup 6} Da under comparable conditions of orientation drawing of the film filaments. This sample was obtained when complex (HL)2L{sub 2}Ti{sub 2}Cl{sub 2} was activated by a 3: 1 mixture of Et{sub 2}AlCl—Bu{sub 2}Mg.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Putting vulnerability to climate change on the map: a review of approaches, benefits, and risks

There is growing demand among stakeholders across public and private institutions for spatially-explicit information regarding vulnerability to climate change at the local scale. However, the challenges associated with mapping the geography of climate change vulnerability are non-trivial, both conceptually and technically, suggesting the need for more critical evaluation of this practice. Here, we review climate change vulnerability mapping in the context of four key questions that are fundamental to assessment design. First, what are the goals of the assessment? A review of published assessments yields a range of objective statements that emphasize problem orientation or decision-making about adaptation actions. Second, how is the assessment of vulnerability framed? Assessments vary with respect to what values are assessed (vulnerability of what) and the underlying determinants of vulnerability that are considered (vulnerability to what). The selected frame ultimately influences perceptions of the primary driving forces of vulnerability as well as preferences regarding management alternatives. Third, what are the technical methods by which an assessment is conducted? The integration of vulnerability determinants into a common map remains an emergent and subjective practice associated with a number of methodological challenges. Fourth, who participates in the assessment and how will it be used to facilitate change? Assessments are often conducted under the auspices of benefiting stakeholders, yet many lack direct engagement with stakeholders. Each of these questions is reviewed in turn by drawing on an illustrative set of 45 vulnerability mapping studies appearing in the literature. A number of pathways for placing vulnerability

54 ENVIRONMENTAL SCIENCES↗

CFD Modeling of Boron Removal from Liquid Silicon with Cold Gases and Plasma

The present study focuses on a specific step of the metallurgical path of purification to provide solar-grade silicon: the removal of boron through the injection of H{sub 2}O(g)-H{sub 2}(g)-Ar(g) (cold gas process) or of Ar-H{sub 2}-O{sub 2} plasma (plasma process) on stirred liquid silicon. We propose a way to predict silicon and boron flows from the liquid silicon surface by using a CFD model (©Ansys Fluent) combined with some results on one-dimensional diffusive-reactive models to consider the formation of silica aerosols in a layer above the liquid silicon. The comparison of the model with experimental results on cold gas processes provided satisfying results for cases with low and high concentrations of oxidants. This confirms that the choices of thermodynamic data of HBO(g) and the activity coefficient of boron in liquid silicon are suitable and that the hypotheses regarding similar diffusion mechanisms at the surface for HBO(g) and SiO(g) are appropriate. The reasons for similar diffusion mechanisms need further enquiry. We also studied the effect of pressure and geometric variations in the cold gas process. For some cases with high injection flows, the model slightly overestimates the boron extraction rate, and the overestimation increases with increasing injection flow. A single plasma experiment from SIMaP (France) was modeled, and the model results fit the experimental data on purification if we suppose that aerosols form, but it is not enough to draw conclusions about the formation of aerosols for plasma experiments.

36 MATERIALS SCIENCE↗

Tensile Behavior of Electron Beam-Welded and Post-Weld Vacuum-Annealed Nb-10% Hf-1% Ti Refractory Alloy Weldments

Nb-10% Hf-1% Ti refractory alloy is a high performance material extensively used for high temperature applications. Electron beam welding is one of the most widely used techniques to join refractory and reactive alloys. Bigger sizes of nozzles for rocket propulsion applications can be either made through deep drawing and flow turning route or by roll bending and welding route both using sheets/plates as input material for fabrication. The latter is a more economical option for mass production of the hardware using such exotic and expensive alloys. In view of this, both as-welded (AW) coupon and weld plus post-weld vacuum-annealed (AW + VA) coupon have been prepared to study their mechanical behavior. It has been observed that tensile strength and ductility have not been reduced in both these conditions vis-à-vis the base metal, confirming weld efficiency of the alloy to be ~ 100%. Microhardness is found to be 150-160 VHN in the base metal and 200-225 VHN in the weld fusion zone in AW condition, which became uniform (145-155 VHN) throughout the weldment in AW + VA condition. Microstructure of the weldment in AW condition is found to be consisting of grains solidified by epitaxial mode from base metal toward the weld centre. In AW + VA condition, improvement in tensile elongation is observed, which is found to be due to the presence of homogenized grains/more uniform microstructure near the heat-affected zone as compared to the steep gradient in grain size in different zones in the weld in AW condition.

36 MATERIALS SCIENCE↗

Hot Roll Bonding of Aluminum to Twin-Roll Cast (TRC) Magnesium and Its Subsequent Deformation Behavior

In an experiment in which twin-roll cast AZ31 magnesium alloy and commercial purity aluminum (AA 1050) sheets were bonded by hot rolling as Al/Mg/Al laminate composites, it was found that increasing the preheating temperatures up to 400 °C enhances the bonding strength of composites. Further increases in the preheating temperatures accelerate the magnesium oxide growth and thus reduce the bonding strength. The influence of the reduction ratio on the bonding properties was also studied, whereby it was observed that increasing the rolling reduction led to an increase in the bonding strength. The experimental results show that the optimum bonding strength can be obtained at rolling temperatures of 375-400 °C with a 50-60% reduction in thickness. On the other hand, the subsequent deformation behavior of composite was assessed using plane strain compression and deep drawing tests. We demonstrate that the composites produced using the optimum roll bonding conditions exhibited sufficient bonding during subsequent deformation and did not reveal any debonding at the bonding interface.

36 MATERIALS SCIENCE↗

Cu-7Cr-0.1Ag Microcomposites Optimized for High Strength and High Condutivity

This paper (i) investigated how the microstructure, conductivity, and mechanical properties of Cu-7Cr-0.1Ag microcomposites were changed by cold drawing and subsequent heat treatment, and (ii) produced the Cu-7Cr-0.1Ag microcomposite with an optimum combination of strength and conductivity. The figure of merit Z (combining strength and conductivity) of the Cu-7Cr-0.1Ag microcomposite was larger than that of the microcomposite without silver for each heat treatment. The value of Z of the Cu-7Cr-0.1Ag microcomposite was a maximum after heat treatment for 1 h at 600 °C, indicating that this was the optimum intermediate heat treatment. The following combinations of conductivity, strength and ductility (measured as elongation to fracture) were obtained by the Cu-7Cr-0.1Ag microcomposite with η = 8: (i) 77.9% IACS (International Annealed Copper Standard), 920 MPa and 3.1%; (ii) 79.3% IACS, 880 MPa and 3.3%; and (iii) 79.9% IACS, 798 MPa and 3.5%. These values for the Cu-7Cr-0.1Ag microcomposite were larger than those of the Cu-7Cr microcomposite.

36 MATERIALS SCIENCE↗

The Effect of Chemical Composition and Processing Technology on the Microstructure, Texture and Earing Behavior of DR Tinplate

The influence of alloying elements and processing technology on the microstructure, crystallographic texture and earing propensity has been investigated in two kinds of DR tinplate differing in Ti content: steel A, no Ti addition, and steel B 0.015% added. The cementite distribution, second-phase particles and the content of dissolved carbon and nitrogen atoms were obtained by SEM, TEM and XPS, respectively. Since the two steels develop both a partial 〈110〉//RD fiber and a {111}//ND fiber, the relative intensities of the several vital texture components seem to differ visibly. There are three types of strengthening mechanisms involved here: strengthening by grain size reduction, solution strengthening and strain hardening. That the tensile strength of steel B is greater than A implies the third mode plays a dominant role in the strength increasing for the DR tinplate. The crystallographic texture of materials not only results in a “preferential orientation” of the mechanical property, but also takes the primary responsibility for ears forming during drawing. Increasing the second cold-rolled reduction is not favorable to reduce the ear height, but this situation seems to be ameliorable. The average ears height of steel B is smaller than that of A, which demonstrated a low level of solute atoms and an ideal texture characteristic before deformation could alleviate the adverse effect caused by an elevated second cold reduction.

36 MATERIALS SCIENCE↗

Microstructural and Property Evolution of Continuous Columnar-Grained Polycrystalline Copper during Extreme Plastic Deformation at Room Temperature

An extreme extensibility with a true strain of 11.12 has been obtained for continuous columnar-grained (CCG) polycrystalline copper at room temperature, which was cold-drawn from a 10-mm-diameter as-cast rod into a 38.5-μm-diameter ultra-fine wire without any intermediate softening heat treatment. During the extreme plastic deformation, the ultimate tensile stress increased from 140 MPa for as-cast CCG copper to 525 MPa for the deformed sample at a true stain of 11.12, while the relative electrical conductivity maintained a high value of 97.6% IACS. On this basis, CCG copper is an excellent raw material for the fabrication of ultra-fine wires with both high strength and high electrical conductivity. The original columnar grains experienced grain subdivision and formed fibrous grains along the drawing direction with a fibrous longitudinal morphology and curly transverse microstructure at medium to high strain. The subdivision of the fibrous grains then went on as the extreme plastic deformation continued. Large amounts of strain-induced boundaries and microstructural refinement facilitated the storage of abundant glide dislocations created by extreme plastic deformation. Thus, extreme plastic extensibility can be achieved through continuous work hardening of CCG copper.

36 MATERIALS SCIENCE↗

Hardening of A6111-T4 Aluminum Alloy at Large Strains and Its Effect on Sheet Forming Operations

In a number of sheet metal stamping and joining processes, the material undergoes large plastic deformation exceeding the range of plastic strain achievable in a standard tensile test prior to material plastic instability. In order to extend the range of effective strains, the multistep rolling process was employed which enabled prestraining of aluminum sheet above 2.0 of true strain. Tensile testing of rolled samples was used to identify the flow stress corresponding to the level of prestrain: By varying the prestrain level, several data points were obtained for the studied flow curve. The numerical simulation using Abaqus software for the cold rolling process of aluminum strips confirmed that majority of the strip is deformed in plane strain compression condition. Performed simulation of the LDH test determined that earlier fracture might occur if the curve obtained via rolling–tensile testing approach is used versus traditional power law approximation and Voce law approximation. The results of simulation for the multistep drawing of a cylindrical cup revealed possible wrinkling in the die entry area during redrawing stage of the process if the rolling–tensile testing flow curve is employed.

36 MATERIALS SCIENCE↗

Effect of Stress States on Twinning Behavior in Twinning-Induced Plasticity Steel

The effects of stress state on the twin structures and kinetics in twinning-induced plasticity (TWIP) steel have been investigated to understand the twinning behaviors in more detail. Twinning behaviors of tension, compression, wire drawing, and caliber rolling were evaluated and compared using the EBSD technique, TEM measurement, and Schmid factor analysis. Twin structures, such as twin thickness, twin variant, twin shape, and twin kinetics were different with stress states. The specimen under compressive stress had wavy-shaped twins, less twin variant, lower twin thickness, and more twin volume fraction in comparison with the specimen under tensile stress. The different structures and kinetics of deformation twin with stress state were highly related to the grain rotation during plastic deformation. Under tensile stress, the grain rotation to <111> orientation, twinning-favored regions by Schmid factor analysis, encouraged the lateral growth of twins, more twin variants, and straight-type twins, while the grain rotation to <110> orientation under compressive stress suppressed the twin growth and twin variant and developed wavy-shaped twins. Drawn wire and caliber-rolled wire had both twin features under tensile and compressive stress states and higher twin volume fraction since complex stress state that combined tension and compression was applied in these processes. The hardness values were strongly related to the twin volume fraction with strain and stress state.

36 MATERIALS SCIENCE↗

Influence of Alternating Short-Cycle Bending on the Mechanical Properties of Copper, α-Titanium and the Mild Steel DC01

The influence of alternating bending loads as they occur during roller levelling on the mechanical properties of sheet metals is not yet fully understood. A detailed knowledge of the influence of the commonly used levelling process on the resulting properties of sheet material is needed in particular for the design of subsequent processes with narrow process windows. To investigate the mechanical property changes during loading conditions similar to roller levelling, sheet samples of mild steel DC01, α-titanium and pure copper (CU-DHP) were subjected to alternating bending loads with different amplitudes for up to 9.5 bending cycles. An isotropic hardening behavior according to a Voce description could be shown for the DC01 deep drawing steel with a strong dependence on the load amplitude applied per cycle. A strengthening behavior that depends on the loading amplitude could be observed for α-titanium as well. In contrast, pure copper featured minor changes with a tendency to soften. For all three materials, changes in springback were present after one bending cycle.

36 MATERIALS SCIENCE↗

The Effect of CO 2 Pressure on Chromia Scale Microstructure at 750°C

To understand and model performance in supercritical CO 2 (sCO 2 ) for high-efficiency, concentrating solar power (CSP) and fossil energy power cycles, reaction rates are compared at 750°C in 0.1 MPa CO 2 and 30 MPa sCO 2 as well as laboratory air as a baseline on structural materials such as Ni-based alloy 625. Due to the thin reaction products formed even after 5000 h, scanning transmission electron microscopy was used to study the Cr-rich surface oxide scale. The scales formed in CO 2 and sCO 2 had a much finer grain size with more voids observed in CO 2 . However, the observations on alloy 625 were complicated by Mo and Nb-rich precipitates in the adjacent substrate and Al internal oxidation. To simplify the system, a binary Ni-22Cr alloy was exposed for 1000 h in similar environments. After exposure in sCO 2 , there was an indication of carbon segregation detected on the Cr 2 O 3 grain boundaries. After exposure in air, metallic Ni precipitates were observed in the scale that were not observed in the scale formed on alloy 625. The scale formed in air on a second Ni-22Cr model alloy with Mn and Si additions did not contain Ni precipitates, suggesting caution when drawing conclusions from model alloys.

36 MATERIALS SCIENCE↗

Experimental Identification and validation of a crystal plasticity model for a low carbon steel on different length scales

Micro-macro approaches are of increasing importance for metal forming simulations and, accordingly, the number of new micro-macro models is increasing as well. Thus, there is a need for adequate identification and validation methods for such models. These methods can be based on experiments on the polycrystalline scale (macro scale), but the use of experiments on the individual single-crystal grain scale (micro scale) has been suggested as well. In this presentation, experiments on both scales and, in parallel, FEM-simulations are presented, in order to compare the results of both approaches. All specimens stem from a rolled sheet of the deep-drawing steel DC04. In addition to the usual macroscopic shear and tensile tests, microscopic indenter tests have been performed. From the micro-indentation tests, which have been applied to single grains of the polycrystalline DC04 steel sheet, various types of deformation data can be measured. Within this presentation we will focus on orientation changes induced by spherical-indentation in the region below the indent, which have been measured using micron-resolution 3D x-ray microscopy and simulated using FEM. In addition, the sensitivity of the calculated orientation changes with respect to {l_brace}110{r_brace} versus {l_brace}112{r_brace} slip planes is discussed.

36 MATERIALS SCIENCE↗

Design Characteristics to Eliminate the Need for Parameter Optimization in Nanoflow ESI-MS

The sampling efficiency in electrospray ionization-mass spectrometry (ESI-MS) can be improved by decreasing the liquid flow rate to the nanoflow regime, where it is possible to draw a large fraction of the ESI plume into the mass spectrometer. This mode of operation is typically more difficult than ESI-MS at higher flow rates because it requires careful optimization of a number of parameters to achieve optimal sampling efficiency. In this work, we screened the relative impact on signal intensity and spray stability of factors that included sprayer position, spray electrode protrusion, sprayer tip shape, spray angle relative to the MS inlet, nebulizer gas flow rate, ESI potential, and means for generating the electric field to initiate electrospray. Based on the screening results, we explore the possibility of providing fixed optimal values for many of the key source parameters to eliminate much of the tuning that is required for conventional nanoflow sources. This approach has potential to greatly simplify nanoflow ESI-MS, while providing optimized sensitivity, stability, and robustness, with decreased variability between analyses. .

77 NANOSCIENCE AND NANOTECHNOLOGY↗