Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “conductors”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

AC losses of Roebel and CORC ® cables at higher AC magnetic fields and ramp rates

We have measured ReBCO coated conductor-based conductor on round core (CORC ® ) and Roebel cables at 77 K in a spinning magnet calorimeter, which subjected the tapes in the samples to a radial magnetic field of 566 mT (peak) at frequencies up to 120 Hz (272 T s -1 , cyclic average) with an approximately sinusoidal waveform. The samples were oriented such that the field applied to the tapes within the cables was entirely radial, simplifying subsequent analysis. An expression for loss which included hysteretic, flux creep and eddy current losses was fit to both the CORC ® and the Roebel cables. This expression allowed easy comparison of the relative influence of eddy currents and flux creep (or power-law behavior) effects. The loss of both the CORC ® and Roebel cables measured here were seen to be essentially the sum of the hysteretic loss, flux creep effects, and the normal metal eddy current losses of the individual tapes. The losses of these cables were measured at high B × d B /d t with no coupling current loss observed under the present preparation conditions. The influence of flux creep effects on loss were not negligible. The losses of the CORC ® cable per meter of tape were seen to be reduced from the case of a flat tape because of the helical geometry of the tapes.

Physics↗
DOE OSTI2022

Rapid assessment of REBCO CC angular critical current density J c (B, T = 4.2 K, θ) using torque magnetometry up to at least 30 tesla

Abstract Detailed design of REBa 2 Cu 3 O 7 − x (REBCO)-based magnets ideally relies on knowledge of the full angular and wide temperature range characterization of the critical current I c of the REBCO coated conductors (CC) at high magnetic fields. In practice, however, obtaining I c ( B , T , θ ) data by the commonly used electrical transport technique is expensive, tedious, and difficult, due to high critical current values that exceed 2000 A for B | | a b -plane ( θ = 90 deg). The conductors are often damaged during angular transport measurements at angles approaching the ab -plane. Therefore, so far, REBCO magnets have been designed without full I c ( B , T , θ ) data sets. Here, we present J c ( B , T , θ ) results for more than twenty samples of CC all made to the same advanced pinning specification produced by SuperPower Inc. For this, we employed torque magnetometry, benchmarking the results to transport I c measurements mostly made away from ab -plane, finding good agreement with scaling factors ≈1–1.3. What is striking is the huge variety of properties exhibited by the samples, even for CC made recently. Given the huge attention now being paid to the effects of screening currents and to the torques generated by offsets between the tape plane and the local magnetic field vector, our data set suggests some caution in detailed design of such magnets without having data of the type presented here.

Physics↗
DOE OSTI2023

Uni-layer magnets: a new concept for LTS and HTS based superconducting magnets

A novel geometrical configuration to form a magnetic field perpendicular to an aperture, created by an asymmetric current distribution, within a single layer, and using a continuous ideal current line, named the uni-layer (UL) magnet, is here presented. The idea is compared to existing concepts in superconducting magnets, namely, the $\cos{\theta}$ sector magnet, stress managed $\cos{\theta}$ and canted $\cos{\theta}$. The UL magnet allows for a design with a continuous unit length (no layer jump), and an increased minimum bending radius of the conductor in relation to traditional $\cos{\theta}$ and canted $\cos{\theta}$ designs. Further, the specific characteristics of the UL design are especially advantageous for strain-sensitive and prone to winding degradation high-temperature superconductors, in very high field accelerator magnet applications, in which, high efficiency in the use of conductor, and a small aperture are required. The advantages with regard to the design and fabrication of UL magnets in relation to other concepts are also discussed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

An experimental study to investigate magnetic field and winding force-dependent contact resistance of NI REBCO coil

Abstract This paper reports the magnetic field and winding force-dependent contact resistance, also known as characteristic resistance, of no-insulation (NI) REBCO coil. Three NI coils were wound with different winding forces ( < 1 kgf, 3 kgf, and 5 kgf) using the same REBCO-coated conductor, and they were tested at 4.2 K in a background field of 0, 5, 10, and 14 T. The contact resistance of each coil is measured at each field. As a result of the measurements, we draw two conclusions. First, a quadratic function for magnetic field intensity reasonably reproduces the measurement results of each NI test coil’s magnetic field-dependent contact resistance, where the practical fit function’s coefficients are determined depending on the winding force. Second, the contact resistance of each coil is partially inconsistent with the magnetoresistance of the electroplated material, i.e. copper, of the REBCO-coated conductor. This paper will present the measurement results in detail, discuss them with Kohler’s rule, and formulate the contact resistance using winding force and magnetic field terms.

Bang, Jeseok (ORCID:0000000247616334)↗
DOE OSTI2024

Protocols and methodologies for acquiring and analyzing critical-current versus longitudinal-strain data in Bi 2 Sr 2 CaCu 2 O 8+x wires

Abstract In the literature on Bi 2 Sr 2 CaCu 2 O 8+ x (Bi-2212) superconducting wires, it is evident that measurement protocols for transport critical-current I c versus longitudinal strain ϵ and definitions of the so-called ‘strain limit’ are generally dissimilar. Yet, values obtained for the ‘strain limit’ are frequently assimilated to being those of the irreversible strain limit ϵ irr , regardless of the I c degradation-criterion used to define it. In effect, ϵ irr should correspond specifically to the I c ( ϵ ) irreversibility onset , where crack formation in Bi-2212 filaments presumably starts. Because I c ( ϵ ) degradation remains progressive over a fairly wide strain range beyond ϵ irr , the different I c degradation-criteria in use do not yield to the same result and, thus, are not equivalent from metrology perspective. Indeed, in studying densified samples of a modern Bi-2212 round wire, we found ϵ irr ≈ 0.4% and ϵ 5% ≈ 0.6% ( ϵ 5% being the strain where I c degrades by 5%). In this paper, we outline and suggest I c ( ϵ )-measurement protocols and data-analysis methodologies in the hope to converge the various approaches taken for studying Bi-2212 strain properties and, thus, remove related result discrepancies. A unified approach would enable more objective data comparisons among laboratories and among different Bi-2212 conductors. It would pave the way for more rigorous studies of effects potentially associated with wire design, powder, heat treatments, and other such parameters on the conductor’s strain properties.

protocols↗
DOE OSTI2025

Distributed fiber-optic sensing in a subscale high-temperature superconducting dipole magnet

High-temperature superconductors, such as REBa2Cu3O7−x (REBCO, RE = rare earth), are becoming pivotal for high-field magnet technology for future circular colliders and compact fusion reactors. The U.S. Magnet Development Program, in collaboration with industry, is developing REBCO magnet technology using round conductors consisting of multiple REBCO tapes. For these multi-tape cables, traditional instrumentation, such as voltage taps and resistive strain gauges, become insufficient to help measure and understand the performance-limiting factors in these model magnets. Distributed fiber-optic sensing (DFOS) is a potential solution to address this challenge. Although DFOS is well established for various applications, measuring temperature and strain in high-temperature superconducting magnets is in its infancy. Here we report the detailed implementation and test results of DFOS based on Rayleigh scattering in a subscale canted cosθ (CCT) dipole magnet using high-temperature superconducting CORC® wires. We co-wound optical fibers in each layer of the CCT magnet and compared different types of commercial fibers and mold-release agents to reduce the power attenuation in the fibers. The DFOS allowed us to measure mechanical deformation and temperature along the conductor during tests at 77 and 4.2 K. The measured strain agreed quantitively with a finite-element mechanical model of the subscale magnet. Our results indicate that DFOS can effectively identify locations of strain and temperature changes, offering unique insight into magnet performance that can advance our understanding and development of the REBCO magnet technology for high-energy physics and fusion applications.

Luo, Linqing↗
DOE OSTI2026

Critical transverse compressive stresses of straight and bent CORC® wires with and without impregnation

CORC® wires are a promising superconductor for accelerator magnet applications. While their excellent uniaxial tensile properties have been well established, potential degradation under transverse compression remains a concern for accelerator magnets, in which transverse compression is a primary stress experienced by superconductors. To evaluate the critical transverse compressive stresses of rare-earth barium copper oxide conductors, we developed an experimental system that enables testing of samples both with and without impregnation in liquid nitrogen. Furthermore, because bending strain induced during coil winding may influence the critical compressive response of CORC® wires, the apparatus was also modified to allow testing under the bending condition. In this study wires were tested for five configurations: (1) straight, non-impregnated, (2) bent, non-impregnated, (3) straight, Stycast 2850 FT-impregnated, (4) bent, Stycast 2850 FT-impregnated, and (5) bent, paraffin wax-impregnated. The transverse pressures corresponding to 3% and 5% reductions in the critical current are reported. In conclusion, the effects of wire bending and impregnation on the critical transverse pressure are analyzed, and the implications for transverse stress levels in accelerator magnet conductors are discussed.

CORC® wire↗
DOE OSTI2025

Systematic analysis of magnetic equilibrium reconstruction with eddy currents on LTX- β

Magnetic equilibrium reconstruction in the Lithium Tokamak Experiment-Beta (LTX-β) is complicated by strong eddy currents and toroidal asymmetries arising from its segmented, close-fitting conducting shell. In the earlier experiment LTX, these three-dimensional (3D) conductor effects significantly distorted diagnostic signals and challenged conventional axisymmetric reconstruction methods. In this work, we demonstrate that accurate plasma equilibria can be recovered on LTX-β by incorporating a small number of dominant eddy current modes derived from realistic conductor models. Using the open-source $\tt{TokaMaker}$ Grad–Shafranov solver, we reconstruct equilibria across a systematically selected set of LTX-β discharges and validate them against the legacy $\tt{PSI-Tri}$ hybrid 2D-3D code. Our results show that fully 2D $\tt{TokaMaker}$ reconstructions achieve significantly improved agreement with flux loop and Mirnov probe measurements, reducing total chi-squared fitting errors, especially during startup. Finally, we develop new hybrid 2D-3D $\tt{TokaMaker}$ reconstructions by integrating the $\tt{ThinCurr}$ 3D eddy current model, which we optimize for significant further reduction of chi-squared in most scenarios. These findings underscore the importance of realistic wall-current modeling in short-pulse tokamaks, and establish a physics-based reconstruction framework that is extensible to devices with complex passive structures and 3D wall interactions.

Grad–Shafranov solver↗
DOE OSTI2020

Evidence of Kramer extrapolation inaccuracy for predicting high field Nb 3 Sn properties

Future applications requiring high magnetic fields, such as the proposed Future Circular Collider, demand a substantially higher critical current density, J c , at fields ≥16 T than is presently available in any commercial strand, so there is a strong effort to develop new routes to higher J c Nb 3 Sn. As a consequence, evaluating the irreversibility field (H irr ) of any new conductor to ensure reliable performance at these higher magnetic fields becomes essential. To predict the irreversibility field for Nb 3 Sn wires, critical current measurements, I c , are commonly performed in the 12-15 T range and the Kramer extrapolation is used to predict higher field properties. Here, the Kramer extrapolation typically models the contribution only for sparse grain boundary pinning, yet Nb 3 Sn wires rely on a high density of grain boundaries to provide the flux pinning that enables their high critical current density. However, whole-field range VSM measurements up to 30 T recently showed for Nb 3 Sn RRP® wires that the field dependence of the pinning force curve significantly deviates from the typical grain boundary shape, leading to a 1-2 T overestimation of Hirr when extrapolated from the typical mid-field data taken only up to about 15 T. In this work we characterized a variety of both RRP® and PIT Nb 3 Sn wires by transport measurements up to 29 T at the Laboratoire National des Champs Magnétiques Intenses (LNCMI), part of the European Magnetic Field Laboratory in Grenoble, to verify whether or not such overestimation is related to the measurement technique and whether or not it is a common feature across different designs. Indeed we also found that when measured in transport the 12-15 T Kramer extrapolation overestimates the actual H irr in both types of conductor with an inaccuracy of up to 1.6 T, confirming that high field characterization is a necessary tool to evaluate the actual high field performance of each Nb 3 Sn wire.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Enhanced tunable cavity development for axion dark matter searches using a piezoelectric motor in combination with gears

Most search experiments sensitive to quantum chromodynamics (QCD) axion dark matter benefit from microwave cavities, as electromagnetic resonators, that enhance the detectable axion signal power and thus the experimental sensitivity drastically. As the possible axion mass spans multiple orders of magnitude, microwave cavities must be tunable and it is desirable for the cavity to have a tunable frequency range that is as wide as possible. Since the tunable frequency range generally increases as the dimension of the conductor tuning rod increases for a given cylindrical conductor cavity system, we developed a cavity system with a large dimensional tuning rod in order to increase this. Here we, for the first time, employed not only a piezoelectric motor, but also gears to drive a large and accordingly heavy tuning rod, where such a combination to increase driving power can be adopted for extreme environments as is the case for axion dark matter experiments: cryogenic, high-magnetic-field, and high vacuum. Thanks to such higher power derived from the piezoelectric motor and gear combination, we realized a wideband tunable cavity whose frequency range is about 42% of the central resonant frequency of the cavity, without sacrificing the experimental sensitivity too much.

47 OTHER INSTRUMENTATION↗
DOE OSTI2026

Measurement of Transverse Resistance for Stacks of Non-insulated REBCO Tapes

Transverse resistance among adjacent conductors is a key parameter to calculate AC losses in superconducting cables with non-insulated conductors. The transverse pressure insert (TPI) previously developed and used at Fermilab was modified to measure transverse resistance of stacks made of non-insulated REBCO tapes as a function of transverse pressure at liquid nitrogen temperature. Pressure up to 322 MPa was applied with a hydraulic cylinder. A small current up to 10 A was flown in the stack sample through REBCO tape leads spliced above and below the stack. The latter had a bending radius larger than 6 mm to prevent the critical current degradation in REBCO leads. The voltage was measured just outside the compressed area. Stack samples included stacks of bare 4-mm wide REBCO tapes, as well as REBCO tapes alternated with 4-mm wide stainless-steel ribbons of 40 μm and 30 μm of thickness. We herein present the results of these transverse resistance measurements. Results show a stronger dependence on pressure for smaller pressure vs. larger ones. Also, of the two components of contact resistance, i.e. contact and bulk, the latter was negligible.

Tamagnini, E. [Turin Polytechnic]↗
DOE OSTI2025

An alternative electrode design for accurate spectral induced polarization measurements in variably saturated porous media

SUMMARY Applications of spectral induced polarization (SIP) require electrodes that maintain hydrologic contact with surrounding soils to capture small electrical responses, often observed as phase shifts in milliradians. For unsaturated soils, electrodes must overcome increased electrical contact impedance due to reduced pore fluid. Traditional designs use a ceramic membrane electrode (CME) with a water reservoir and metal conductor, requiring periodic maintenance to retain electrolytic solution. For field applications where maintenance is impractical, alternative designs are needed. This study evaluated a new electrode design (silica flour electrode, SFE) alongside a CME. SFEs use packed silica flour to store water via capillary forces against a metal conductor. This study examined both designs in three variably saturated soils at soil suctions up to 700 mbar and soil water contents below 1 percent, with SIP measurements across 0.01 to 10 000 Hz frequencies. SFEs match CMEs at high frequencies and perform better at lower frequencies, without requiring ongoing maintenance, making them ideal for field use. In water-only experiments, CMEs produced errors and high noise below 1.5 Hz, whereas SFEs were more accurate. However, CMEs performed better above 300 Hz. In fine sand, SFEs performed better due to the relatively lower contact impedance as compared to CMEs. Both electrode types performed comparably in silty sand and silt loam soils, although CMEs required ongoing maintenance, suggesting potential for long-term reliability issues.

58 GEOSCIENCES↗
DOE OSTI2021

Paradigms of frustration in superionic solid electrolytes

Superionic solid electrolytes have widespread use in energy devices, but the fundamental motivations for fast ion conduction are often elusive. In this Perspective, we draw upon atomistic simulations of a wide range of superionic conductors to illustrate some ways frustration can lower diffusion cation barriers in solids. Based on our studies of halides, oxides, sulfides and hydroborates and a survey of published reports, we classify three types of frustration that create competition between different local atomic preferences, thereby flattening the diffusive energy landscape. These include chemical frustration, which derives from competing factors in the anion–cation interaction; structural frustration, which arises from lattice arrangements that induce site distortion or prevent cation ordering; and dynamical frustration, which is associated with temporary fluctuations in the energy landscape due to anion reorientation or cation reconfiguration. For each class of frustration, we provide detailed simulation analyses of various materials to show how ion mobility is facilitated, resulting in stabilizing factors that are both entropic and enthalpic in origin. We propose the use of these categories as a general construct for classifying frustration in superionic conductors and discuss implications for future development of suitable descriptors and improvement strategies.

25 ENERGY STORAGE↗
DOE OSTI2025

Origin of Intrinsically Low Thermal Conductivity in a Garnet-Type Solid Electrolyte: Linking Lattice and Ionic Dynamics with Thermal Transport

Understanding thermal transport in solid electrolytes is essential for improving the performance, reliability, and safety of all-solid-state batteries. Garnet-type lithium-ion conductors are promising candidates for solid electrolytes, yet their thermal-transport mechanisms remain poorly understood. Here, we connect the lattice and ion dynamics of single-crystal garnet-type Li 6.5 La 3 Zr 1.5 Ta 0.5 O 12 to its intrinsically low thermal conductivity. Our study reveals that the single crystals grown by the floating-zone method exhibit remarkably low glasslike thermal conductivity. Using first-principles calculations and inelastic-neutron-scattering measurements, we identify both the acoustic and numerous optical phonon modes, which stem from the complex crystal structure of the material. Notably, a low-energy optical branch exhibits an avoided crossing with acoustic phonons near 7 meV. These optical modes can enhance the scattering of heat-carrying acoustic phonons and reduce thermal conductivity. Furthermore, the calculated Grüneisen parameters are large, especially for the vibrational modes around 6 meV, indicating strong anharmonicity, with a noticeable contribution from lithium-ion vibrations. A two-channel thermal-transport model is employed to describe the weak temperature dependence of the thermal conductivity, which can be attributed to the substantial contribution of diffuson transport facilitated by the abundance of optical phonons and intrinsic anharmonicity. These results offer valuable insights into the thermal transport in a broad class of ionic conductors of interest for energy conversion and storage applications.

Ab initio calculations↗
DOE OSTI2020

Scanning Tunneling Thermometry

The best spatial resolution so far achieved in thermal imaging is several nanometers, much coarser than routinely achieved for other physical properties. Here we propose a method to map electronic temperature variations in operating nanoscale conductors by relying solely upon electrical tunneling current measurements. The proposed measurement scheme involves two scanning probe operations to measure the conductance and thermopower, respectively. These two measurements are shown to determine the local temperature with high accuracy in nanoscale conductors, where the Wiedemann-Franz law holds quite generally. We report the proposed scanning tunneling thermometer, owing to its operation in the tunneling regime, would be capable of mapping temperature variations with subnanometer resolution, thereby enhancing the resolution of scanning thermometry by some 2 orders of magnitude.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Topological edge conduction induced by strong anisotropic exchange interactions

Here, we predict that an interplay between isotropic and anisotropic exchange interactions in a honeycomb lattice structure can lead to topological edge conduction when the anisotropic interaction is at least twice the strength of the isotropic interaction. For materials like Na 2 ⁢IrO 3 , such a strong anisotropic exchange interaction simultaneously induces a zigzag type of antiferromagnetic order that breaks the time-reversal symmetry of the topological edge conductor. We show that the electronic transport in such topological conductors will exhibit a quantized Hall conductance without any external magnetic field when the Fermi energy lies within a particular energy range.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Remote Mesoscopic Signatures of Induced Magnetic Texture in Graphene

Mesoscopic conductance fluctuations are a ubiquitous signature of phase-coherent transport in small conductors, exhibiting universal character independent of system details. Here, however, we demonstrate a pronounced breakdown of this universality, due to the interplay of local and remote phenomena in transport. Our experiments are performed in a graphene-based interaction-detection geometry, in which an artificial magnetic texture is induced in the graphene layer by covering a portion of it with a micromagnet. When probing conduction at some distance from this region, the strong influence of remote factors is manifested through the appearance of giant conductance fluctuations, with amplitude much larger than e 2 / h . This violation of one of the fundamental tenets of mesoscopic physics dramatically demonstrates how local considerations can be overwhelmed by remote signatures in phase-coherent conductors.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Polarons and electrical leakage in BaZrO 3 and BaCeO 3

The proton conductors barium zirconate (BaZrO 3 , or BZO), barium cerate (BaCeO 3 , or BCO), and their alloys have attracted considerable interest as solid-state electrolytes in solid-oxide fuel and electrolysis cells. However, the reasons for their non-negligible electrical conductivity, which can limit their performance, are not fully understood. To address that question, we use first-principles calculations based on density functional theory to study the properties of hole and electron polarons in BZO and BCO. We confirm that hole polarons form in both materials, slightly more favorably in BCO. Electron polarons, on the other hand, are stable only in BCO and in Ce-containing alloys; in pure BZO, electron polaron states are unfavorable relative to free carriers, though they become accessible when Ce impurities are introduced. In general, doped BZO and BCO will have negligible electron concentrations, but larger concentrations of holes and hole polarons may be present. Avoiding extreme O-rich conditions and limiting dopant concentrations are key strategies for reducing significant p -type electrical leakage. Furthermore, our results provide physical insights into the different electronic behaviors of BZO and BCO, which can be used to optimize their performance as pure ionic conductors.

08 HYDROGEN↗