Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “compositional properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

3D Printed Ceramic Reinforced Polymer Composites Microstructure and Mechanical Properties

In Fused Filament Fabrication (FFF) 3D printing a part is made by extruding material layer by layer. Benefits of FFF are the ability to print complex shapes quickly and at a lower cost compared to other manufacturing methods. In this work, filaments composed of either silicon carbide (SiC) or zirconium silicate ceramic particulates in a polylactic-acid (PLA) matrix were used to print specimens for microstructural analysis and mechanical testing. Pure PLA samples were also printed and tested as a baseline for comparison. A Design of Experiments approach was used to test the interactions between three different parameters and their effect on ultimate strength, Young’s modulus, and yield strength. For compression test specimens, these parameters were infill percentage, number of shells, and print orientation angle. For tensile test specimens, the parameters were layer height, number of shells, and infill orientation angle. Pre- and post-compression test samples were evaluated by scanning electron microscopy for microstructural analysis. Infill percentage had the greatest effect on mechanical properties while number of shells and print orientation angle had minor effects. When changing the layer lines from perpendicular to parallel, relative to the loading direction, SiC-PLA had higher mechanical properties while pure PLA properties had decreased, and zirconium silicate-PLA had mix results.

Fused filament fabrication↗
DOE OSTI2020

Stimuli-responsive petroleum cement composite with giant expansion and enhanced mechanical properties

Shrinkage, as an inherent property of cement during the curing process, has been a concern in the oil & gas industry for centuries. Therefore, expansive cement has been studied for many decades, primarily through incorporation of expansive additives. Nevertheless, traditional expansive additives are not able to achieve the required expansive ratio or maintain a good mechanical property for the cement composite at extreme underground condition. Accordingly, a new generation of expansive additive, which not only has the required expansion, but also work at the downhole high temperature and high pressure environment, and maintain or even enhance the mechanical property, is highly desired. In this work, a high enthalpy storage shape memory polymer (SMP) as a new class of expansive additive is investigated. It is found that the cement composite achieves 1.4% circumferential expansion by only 6% by weight of SMP additives. The compressive strength and flexural strength are also enhanced at the same time, which is hardly achievable by other expansive additives with the same concertation. Good pumpability is also proved by rheological study. The mechanism controlling the enhanced properties is reveled through morphological study and element mapping analysis at the SMP/cement interface.

36 MATERIALS SCIENCE↗
NASA NTRS1985

Tough composite materials: Recent developments

The present volume broadly considers topics in composite fracture toughness and impact behavior characterization, composite system constituent properties and their interrelationships, and matrix systems' synthesis and characterization. Attention is given to the characterization of interlaminar crack growth in composites by means of the double cantilever beam specimen, the characterization of delamination resistance in toughened resin composites, the effect of impact damage and open holes on the compressive strength of tough resin/high strain fiber laminates, the effect of matrix and fiber properties on compression failure mechanisms and impact resistance, the relation of toughened neat resin properties to advanced composite mechanical properties, and constituent and composite properties' relationships in thermosetting matrices. Also treated are the effect of cross-link density on the toughening mechanism of elastomer-modified epoxies, the chemistry of fiber/resin interfaces, novel carbon fibers and their properties, the development of a heterogeneous laminating resin, solvent-resistant thermoplastics, NASA Lewis research in advanced composites, and opportunities for the application of composites in commercial aircraft transport structures.

Vosteen, L. F.↗
DOE OSTI2025

Advances in additive manufacturing, materials, and applications with AI/ML

There is high interest in making digital manufacturing a central facet of the new manufacturing landscape. However, in the materials science world, there is much work and opportunity to realize the full potential of artificial intelligence/machine learning (AI/ML) with regard to the structure–composition–processing–property (SCPP) relationship. For polymers (thermoplastics, thermosets, elastomers) and composites (nanocomposites), the origin of their high performance and even recyclability starts with design and formulation. Processing methods enable more property development based on curing, shape-factor forming, and anisotropic directionality. In subtractive manufacturing, high-performance and engineering polymers can be shaped and milled to very high tolerance and specifications and used as replacements for metals and alloys. In conclusion, this typically relies on digital manufacturing methods but tends to be wasteful in materials.

Lara-Ceniceros, Tania E. [Centro de Investigación ↗
NASA NTRS1996

Development of a material property database on selected ceramic matrix composite materials

Ceramic Matrix Composites, with fiber/whisker/particulate reinforcement, possess the attractive properties of ceramics such as high melting temperature, high strength and stiffness at high temperature, low density, excellent environmental resistance, combined with improved toughness and mechanical reliability. These unique properties have made these composites an enabling technology for thermomechanically demanding applications in high temperature, high stress and aggressive environments. On a broader scale, CMC's are anticipated to be applicable in aircraft propulsion, space propulsion, power and structures, in addition to ground based applications. However, it is also true that for any serious commitment of the material toward any of the intended critical thermo-mechanical applications to materialize, vigorous research has to be conducted for a thorough understanding of the mechanical and thermal behavior of CMC's. The high technology of CMC'S is far from being mature. In view of this growing need for CMC data, researchers all over the world have found themselves drawn into the characterization of CMC's such as C/SiC, SiC/SiC, SiC/Al203, SiC/Glass, SiC/C, SiC/Blackglas. A significant amount of data has been generated by the industries, national laboratories and educational institutions in the United States of America. NASA/Marshall Space Flight Center intends to collect the 'pedigreed' CMC data and store those in a CMC database within MAPTIS (Materials and Processes Technical Information System). The task of compilation of the CMC database is a monumental one and requires efforts in various directions. The project started in the form of a summer faculty fellowship in 1994 and has spilled into the months that followed and into the summer faculty fellowship of 1995 and has the prospect of continuing into the future for a healthy growth, which of course depends to a large extent on how fast CMC data are generated. The 10-week long summer fellowship has concentrated, basically, on establishing the procedure for a smooth transfer of data into a CMC database on MAPTIS which is a vital part of the following broader picture of the project.

Mahanta, Kamala↗
DOE OSTI2021

The In Situ Ion Irradiation Toolbox: Time-Resolved Structure and Property Measurements

Abstract The dynamic interactions of ions with matter drive a host of complex evolution mechanisms, requiring monitoring on short spatial and temporal scales to gain a full picture of a material response. Understanding the evolution of materials under ion irradiation and displacement damage is vital for many fields, including semiconductor processing, nuclear reactors, and space systems. Despite materials in service having a dynamic response to radiation damage, typical characterization is performed post-irradiation, washing out all information from transient processes. Characterizing active processes in situ during irradiation allows the mechanisms at play during the dynamic ion-material interaction process to be deciphered. In this review, we examine the in situ characterization techniques utilized for examining material structure, composition, and property evolution under ion irradiation. Covering analyses of microstructure, surface composition, and material properties, this work offers a perspective on the recent advances in methods for in situ monitoring of materials under ion irradiation, including a future outlook examining the role of complementary and combined characterization techniques in understanding dynamic materials evolution.

36 MATERIALS SCIENCE↗
NASA NTRS2001

Automated Tow Placed LaRC(TM)-PETI-5 Composites

LaRC(TM)-PETI-5 is a PhenylEthynyl-Terminated Imide resin developed at NASA Langley Research Center (LaRC) during the 1990s. It offers a combination of attractive composite and adhesive properties. IM7/LaRC(TM)-PETI-5 composites exhibit thermal and thermo-oxidative stability typical of polyimides, superior chemical resistance and processability, excellent mechanical properties, toughness and damage tolerance. It was selected for study in the High Speed Research program aimed at developing technologies for a future supersonic aircraft, the High Speed Civil Transport, with a projected life span of 60 000 h at a cruise speed up to Mach 2.4. Robust autoclave processing cycles for LaRC(TM)-PETI-5 composites have been thoroughly designed and demonstrated, which involved hand lay-up of solvent-ladened 'wet' prepregs. However, this type of processing is not only costly but also environmentally unfriendly. Volatile management and shrinkage could become serious problems in the fabrication of large complex airframe structural subcomponents. Robotic tow placement technology utilizing 'dry' material forms represents a new fabrication process which overcomes these deficiencies. This work evaluates and compares mechanical properties of composites fabricated by heated head automated tow placement (dry process) with those obtained by hand lay-up/autoclave fabrication (wet process). Thermal and rheological properties of the robotically as-placed uncured composites were measured. A post-cure cycle was designed due to the requirement of the PETI-5 resin for a 370 C/1 h hold to reach full cure, conditions which cannot be duplicated during heated head robotic placement. Mechanical properties such as 0 degree flexural strength and modulus, open hole tensile and compressive strength and moduli, reduced section compression dogbone compressive strength, and modified zippora-medium small (MZ-MS) tensile and compressive properties were obtained on the post-cured panels. These properties compared favourably with those obtained from the wet process.

Hou, T. H.↗
DOE OSTI2023

High Layer Number ( n = 1–6) 2D Ruddlesden–Popper Lead Bromide Perovskites: Nanosheets, Crystal Structure, and Optoelectronic Properties

2D Ruddlesden–Popper (RP) lead halide perovskites have highly tunable structures, compositions, and properties that enable their promising optoelectronic applications. Among various 2D halide perovskites, the materials chemistry and fundamental optoelectronic properties of high layer number (n) lead-bromide RP perovskites, where n refers to the number of inorganic octahedra layers, have been less studied. Here, we report the synthesis of thin nanosheets of (PEA) 2 Cs n–1 Pb n Br 3n+1 (n = 1–6, PEA = phenylethylammonium) perovskites and study the optical properties, assigning photoluminescence emissions of 486, 496, and 505 nm to n = 4–6 phases, respectively, and reporting the photoluminescence lifetimes. Furthermore, the crystal structure of (PEA) 2 Cs 2 Pb 3 Br 10 was determined to reveal minimal octahedral structural distortions. Ultraviolet photoelectron spectroscopy measurements reveal the positioning of the valence and conduction bands for n = 1–3 phases and confirm the type-I band alignment for the (PEA) 2 Cs n–1 Pb n Br 3n+1 series, laying the foundation for rational heterostructure device design in the future.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1981

Modulus, strength and thermal exposure studies of FP-Al2O3/aluminum and FP-Al2O3/magnesium composites

The mechanical properties of FP-Al2O3 fiber reinforced composites prepared by liquid infiltration techniques are improved. A strengthening addition, magnesium, was incorporated with the aluminum-lithium matrix alloy usually selected for these composites because of its good wetting characteristics. This ternary composite, FP-Al2O3/Al-(2-3)Li-(3-5)Mg, showed improved transverse strength compared with FP-Al2O3/Al-(2-3)Li composites. The lower axial strengths found for the FP-Al2O3/Al-(2-3)Li-(3-5)Mg composites were attributed to fabrication related defects. Another technique was the use of Ti/B coated FP-Al2O3 fibers in the composites. This coating is readily wet by molten aluminum and permitted the use of more conventional aluminum alloys in the composites. However, the anticipated improvements in the axial and transverse strengths were not obtained due to poor bonding between the fiber coating and the matrix. A third approach studied to improve the strengths of FP-Al2O3 reinforced composites was the use of magnesium alloys as matrix materials. While these alloys wet fibers satisfactorily, the result indicated that the magnesium alloy composites used offered no axial strength or modulus advantage over FP-Al2O3/Al-(2-3)Li composites.

Bhatt, R. T.↗
NASA NTRS1991

Ductility of a continuous fiber reinforced aluminum matrix composite

The transverse properties of an aluminum alloy metal matrix composite reinforced by continuous alumina fibers have been investigated. The composite is subjected to both mechanical and cyclic thermal loading. The ductility can vary by an order of magnitude according to the operating conditions. For high mechanical and low thermal loading the ductility is small, for low mechanical and high thermal loading the ductility is an order of magnitude higher. Experiments on a beam in bending confirm that the ductility is strongly dependent on the loading conditions. The observations suggest a means of utilizing the inherent ductility of the matrix.

Jansson, S.↗
NASA NTRS2004

Melt-infiltrated Sic Composites for Gas Turbine Engine Applications

SiC-SiC ceramic matrix composites (CMCs) manufactured by the slurry -cast melt-infiltration (MI) process are leading candidates for many hot-section turbine engine components. A collaborative program between Goodrich Corporation and NASA-Glenn Research Center is aimed at determining and optimizing woven SiC/SiC CMC performance and reliability. A variety of composites with different fiber types, interphases and matrix compositions have been fabricated and evaluated. Particular focus of this program is on the development of interphase systems that will result in improved intermediate temperature stressed-oxidation properties of this composite system. The effect of the different composite variations on composite properties is discussed and, where appropriate, comparisons made to properties that have been generated under NASA's Ultra Efficient Engine Technology (UEET) Program.

Morscher, Gregory N.↗
NASA NTRS1990

Polymeric Additives For Graphite/Epoxy Composites

Report describes experimental studies of properties of several graphite/epoxy composites containing polymeric additives as flexibilizing or toughening agents. Emphasizes effects of brominated polymeric additives (BPA's) with or without carboxy-terminated butadiene acrylonitrile rubber. Reviews effects of individual and combined additives on fracture toughnesses, environmental stabilities, hot/wet strengths, thermomechanical behaviors, and other mechanical properties of composites.

Kourtides, D. A.↗
DOE OSTI2022

High-fidelity micromechanical modeling of the effects of defects on damage and creep behavior in single tow ceramic matrix composite

Despite the superior properties of ceramic matrix composites (CMCs), their fabrication process generates inevitable defects with high density that significantly influence material integrity and residual useful life. Recent efforts have focused on CMC property prediction and investigation of their different inelastic mechanisms, but very limited work exists on understanding the influence of defects on inelastic responses of CMCs. Here, we introduce a three-dimensional micromechanics computational framework that includes experimentally informed material microstructure and architectural variabilities to investigate CMC response in the presence of manufacturing-induced defects. A developed microstructure generation algorithm is used to generate the representative volume elements in the micromechanics models from complex material morphology information obtained from extensive characterization studies of C/SiNC and SiC/SiNC CMCs. A fracture mechanics-informed matrix damage model is reformulated, in which the model considers the growth of porosity and microcracks in the as-received material. A progressive fiber damage model as well as Orthotropic viscoplasticity creep formulation are also utilized for the study. This methodology is implemented within the micromechanics framework to investigate the complex temperature- and time-dependent load transfer and damage mechanisms of CMCs under operation loading conditions. The developed framework explores the influence of as-received defects on the damage and creep behavior in service conditions. It also provides new insights into the effect of size, shape, distribution, and location of these defects on material response. The framework is then calibrated with unidirectional CMC minicomposite results available in the literature.

36 MATERIALS SCIENCE↗
NASA NTRS1990

Stress Dependence of Ultrasonic Velocity in Unidirectional Graphite/Epoxy Composites for Longitudinal Waves Propagating Along the Direction of Stress

The first measurements of the stress induced velocity changes for propagation directions along the direction of applied stress in gr/ep composites have been presented. For propagation and stress direction perpendicular to the fiber direction, the data demonstrated a linear relation between normalized velocity shift and stress. After corrections for the delay line were made, the slope or SAC was determined and compared favorably with the expected value calculated from the previously determined nonlinear coefficients of this material. The ratio of the SAC to the elastic compliance for this direction of loading was evaluated and found to have a value similar to numerous other materials which have very different linear elastic properties. Measurements with stress and propagation along the fibers yielded unusual behavior. The curves were very nonlinear and even shifted direction at higher loads. The large scatter in the data due to bond variations made separation of material effects from bond induced artifacts impossible. Thus the SAC, R, and the remaining two unknown TOEC's could not be determined for this direction of propagation. These measurements further expand the basis of determining nonlinear elastic properties of composite materials. These properties may be useful in developing much needed NDE techniques to determine such important parameters as residual stress after cure and residual strength after impact damage. Additional study is needed to measure the nonlinear behavior in other composite materials including angle ply laminates. Also, other techniques to measure elastic nonlinearity such as harmonic generation should be applied to composites to improve the understanding of these properties and their importance.

Prosser, William H.↗