Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “characterization techniques”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Characterization of mechanical deformation in aluminum by optical second harmonic generation

Second harmonic generation (SHG), a laser-based surface technique, was used to characterize near-surface defect evolution associated with mechanical deformation in 2024-T3 aluminum due to tensile loads. Electron backscatter diffraction (EBSD) measurements were also performed to determine the geometrically necessary dislocation density before and after tensile deformation. Comparison of the EBSD and SHG results found that dislocation density and SHG signal are inversely proportional; tensile deformation in the plastic regime led to an increase in dislocation density and a decrease in SHG response. A similar trend was seen in the SHG results on as-received (unpolished) Al samples; SHG response decreases with extent of plastic deformation. Furthermore, this study suggests that SHG has potential as a nondestructive evaluation technique.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Squeeze Film Damper Experimental and Numerical Correlation: Test Setup Description and Parameter Identification of Dry System

The process of characterizing a damper involves both experimental techniques and model simulation. Experiments characterize dynamic behavior of a system through empirical modal analysis using impact and shaker testing. The layout of the test setup is crucial for a low-mass, nonlinear system. Physical arrangement, orientation of the system, and instrumentation affect the results that are discussed in this paper. These results can be used to validate a numerical simulation of the same system. With a validated model, important physical input parameters and modeling techniques can be determined and implemented in future designs. In other words, this modeling can be used with confidence to design alternative dampers that may be difficult, costly, and time-consuming to characterize experimentally.

Cook, Jason↗
DOE OSTI2024

YOLO2U-Net: Detection-guided 3D instance segmentation for microscopy

Microscopy imaging techniques are instrumental for characterization and analysis of biological structures. As these techniques typically render 3D visualization of cells by stacking 2D projections, issues such as out-of-plane excitation and low resolution in the z-axis may pose challenges (even for human experts) to detect individual cells in 3D volumes as these non-overlapping cells may appear as overlapping. In this paper a comprehensive method for accurate 3D instance segmentation of cells in the brain tissue is introduced. The proposed method combines the 2D YOLO detection method with a multi-view fusion algorithm to construct a 3D localization of the cells. Next, the 3D bounding boxes along with the data volume are input to a 3D U-Net network that is designed to segment the primary cell in each 3D bounding box, and in turn, to carry out instance segmentation of cells in the entire volume. The promising performance of the proposed method is shown in comparison with current deep learning-based 3D instance segmentation methods.

3D instance segmentation↗
DOE OSTI2022

Applying Waveform Correlation and Waveform Template Metadata to Aftershocks in the Middle East to Reduce Analyst Workload

Organizations that monitor for underground nuclear explosive tests are interested in techniques that automatically characterize recurring events such as aftershocks to reduce the human analyst effort required to produce high-quality event bulletins. Waveform correlation is a technique that is effective in finding similar waveforms from repeating seismic events. In this study, we apply waveform correlation in combination with template event metadata to two aftershock sequences in the Middle East to seek corroborating detections from multiple stations in the International Monitoring System of the Preparatory Commission for the Comprehensive Nuclear-Test-Ban Treaty Organization. We use waveform templates from stations that are within regional distance of aftershock sequences to detect subsequent events, then use template event metadata to discover what stations are likely to record corroborating arrival waveforms for recurring aftershock events at the same location, and develop additional waveform templates to seek corroborating detections. We evaluate the results with the goal of determining whether applying the method to aftershock events will improve the choice of waveform correlation detections that lead to bulletin-worthy events and reduction of analyst effort.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
DOE OSTI2025

Detecting rare earth elements via optically detected magnetic resonance (ODMR) and spin-relaxometry using nitrogen vacancy centers in nanodiamonds

Nanodiamonds embedded with nitrogen-vacancy (NV) centers are emerging as powerful tools in quantum sensing due to their remarkable sensitivity to local variations in electromagnetic fields, temperature, and pressure. These point defects in the diamond lattice can be probed using optically detected magnetic resonance (ODMR) and spin relaxometry techniques, allowing for the detection and characterization of magnetic nanoparticles and ions. The sensing mechanism relies on laser-induced excitation of the NV center's non-degenerate triplet ground state, which promotes electrons to an excited state. Subsequent photoluminescence (PL) emission, which is spin-state dependent, is then measured. These spin states are highly responsive to magnetic perturbations in the surrounding environment. By analyzing changes in the ODMR spectra and spin relaxation times, we can effectively monitor how magnetic species influence the NV center's spin dynamics, thus enabling sensitive and selective characterization of nanoscale magnetic materials. These techniques have been applied for the characterization of transition metals and rare earth elements which shows natural ferromagnetic properties.

magnetic nanopartgicles and ions↗
DOE OSTI2023

Conotoxin Prediction: New Features to Increase Prediction Accuracy

Conotoxins are toxic, disulfide-bond-rich peptides from cone snail venom that target a wide range of receptors and ion channels with multiple pathophysiological effects. Conotoxins have extraordinary potential for medical therapeutics that include cancer, microbial infections, epilepsy, autoimmune diseases, neurological conditions, and cardiovascular disorders. Despite the potential for these compounds in novel therapeutic treatment development, the process of identifying and characterizing the toxicities of conotoxins is difficult, costly, and time-consuming. This challenge requires a series of diverse, complex, and labor-intensive biological, toxicological, and analytical techniques for effective characterization. While recent attempts, using machine learning based solely on primary amino acid sequences to predict biological toxins (e.g., conotoxins and animal venoms), have improved toxin identification, these methods are limited due to peptide conformational flexibility and the high frequency of cysteines present in toxin sequences. This results in an enumerable set of disulfide-bridged foldamers with different conformations of the same primary amino acid sequence that affect function and toxicity levels. Consequently, a given peptide may be toxic when its cysteine residues form a particular disulfide-bond pattern, while alternative bonding patterns (isoforms) or its reduced form (free cysteines with no disulfide bridges) may have little or no toxicological effects. Similarly, the same disulfide-bond pattern may be possible for other peptide sequences and result in different conformations that all exhibit varying toxicities to the same receptor or to different receptors. We present here new features, when combined with primary sequence features to train machine learning algorithms to predict conotoxins, that significantly increase prediction accuracy.

collisional cross section↗
DOE OSTI2023

Detecting and characterizing special nuclear material for nuclear nonproliferation applications

Abstract There is an urgent need for new, better instrumentation and techniques for detecting and characterizing special nuclear material (SNM), i.e., highly enriched uranium and plutonium. The development of improved instruments and techniques requires experiments performed with the SNM itself, which is of limited availability. This paper describes the findings of experiments performed at the National Criticality Experiments Research Center conducted using new instruments and techniques on unclassified, kg-quantity SNM objects. These experiments, performed in the framework of the Department of Energy, National Nuclear Security Administration Consortium for Monitoring, Technology, and Verification, focused on detecting, characterizing, and localizing SNM samples with masses ranging from 3.3 to 13.8 kg, including plutonium and highly enriched uranium using prototype detectors and techniques. The work demonstrates SNM detection and characterization using recently-developed prototype detection systems. Specifically, we present new results in passive detection and imaging of plutonium and uranium objects using gamma-ray and dual particle (fast neutron and gamma-ray) imaging. We also present a new analysis of the delayed neutron emissions during active interrogation of uranium using a neutron generator.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2025

Data-Driven Tailoring Optimization of Thermoset Polymers Using Ultrasonics and Machine Learning

Thermoset polymers are highly demanded for their structural robustness, thermal stability, and chemical resistance. Tailoring the properties of these polymers for high-performance applications is often preferred to designing brand-new polymers. However, the traditional destructive techniques used to characterize their properties as a function of manufacturing parameters are expensive and time-consuming. A novel non-destructive, data-driven method leveraging ultrasonics and machine learning techniques to tailor the properties of thermosets as a function of the manufacturing parameters is demonstrated. Thermoset epoxy samples with varying curing temperatures (15–40 °C) and curing agent amounts (±40%) were manufactured and tested. Their curing kinetics were monitored by determining the sound speed in the material in real time, while the longitudinal modulus of the samples was determined post-cure. Machine learning models were developed using a k-nearest neighbors algorithm. These models were implemented to predict the curing and final elastic properties using the manufacturing parameters, i.e., stoichiometry and curing temperature, and vice versa. Understanding and modeling how these parameters affect the cure kinetics and final properties will allow for efficient and reliable optimization of thermoset tailoring and manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Characterization of the strain-rate–dependent mechanical response of single cell–cell junctions

Cell–cell junctions are essential components in multicellular structures and often experience strains of different magnitudes and rates. However, their mechanical behavior is currently underexplored due to the lack of techniques to quantitatively characterize junctional stress–strain relationships. Here we developed a polymeric microstructure to strain the mutual junction of a single cell pair while simultaneously recording the junction stress and observed previously unseen strain-rate–dependent junction responses. We showed that cytoskeleton growth could relax the stress buildup and prevent junction failure at low strain rates, while high strain rates led to synchronized junction failures at remarkably large strains (over 200%). We expect this platform and our biophysical understanding to form the foundation for the rate-dependent mechanics of cell–cell junctions.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Non-Markovian relaxation spectroscopy of fluxonium qubits

Recent studies have shown that parasitic two-level systems (TLS) in superconducting qubits, which are a leading source of decoherence, can have relaxation times longer than the qubits themselves. However, the standard techniques used to characterize qubit relaxation is only valid for measuring T 1 under the Born-Markov approximation and could mask environmental memory effects in practice. Here, we introduce two-timescale relaxometry, a technique to probe the qubit and environment relaxation simultaneously and efficiently. We apply it to high-coherence fluxonium qubits over a frequency range of 0.1-0.4 GHz, and reveal a discrete spectrum of TLS with millisecond lifetimes. Our analysis of the spectrum is consistent with a random distribution of TLS in the aluminum oxide tunnel barrier of the Josephson junction chain of the fluxonium, with a spectral and volumetric density and average electric dipole similar to previous TLS studies at much higher frequencies. Our study suggests that investigating and mitigating TLS in the junction chain is crucial to the development of various types of noise-protected qubits in circuit QED.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Multiscale Characterization of the Caney Shale — An Emerging Play in Oklahoma

From a hydrocarbon perspective, the Caney Shale has historically been evaluated as a sealing unit, which resulted in limited studies characterizing the rock properties of the Caney Shale and its suitability for hydraulic fracturing. The objective of our research is to help bridge the current knowledge gap through the integration of multiscale laboratory techniques and to characterize the macro- and microscale rock properties of the Caney Shale. We employed an integrated approach for the characterization of the Caney using 200 ft (61 m) of Caney core from a target well in southern Oklahoma. Core observation and petrographic analysis of thin sections were combined to characterize the general rock types and associated fabrics and textures. Mineralogical composition, pore system architecture, and rock fabric were analyzed using x-ray diffraction (XRD), scanning electron microscopy/energy dispersive x-ray spectroscopy (SEM/EDS), and focused ion beam (FIB)-SEM. In addition, rebound hardness and indentation testing were carried out to determine rock hardness (brittleness) and elasticity, respectively. With the integrated multiscale characterization, three mixed carbonate-siliciclastic rock types were identified — mudstone, calcareous siltstone, and silty carbonate — likely representing a spectrum of deposition from low to relatively high energy environments in the distal portions of a ramp system. Silty carbonate contains mostly interparticle pores. The calcareous siltstones and silty mudstones contain a combination of organic matter pores and interparticle pores. Each of the rock types shows unique mineralogical compositions based on XRD. The mudstone lithofacies has the highest clay content and the least carbonate content. Calcareous siltstones show moderate carbonate and clay content. Silty carbonate indicates the highest carbonate content with the least clay content. In an order of mudstone, calcareous siltstone, and silty carbonate, rebound hardness and Young’s modulus show an increasing trend. As a result of rock-fluid interactions, there are potential scaling reactions during completion and production that could ultimately affect permeability and production rates. Overall, the proposed multiscale integration approach is critical for the geologic characterization of most rocks. However, in shale reservoirs dominated by microporosity and microstructure where engineered fractures are expected to provide permeability at a reservoir scale, successful integration is essential. An optimized, integrated geological characterization of the Caney Shale that is well aligned with the engineering designs in drilling, completing, and producing wellbores will ultimately lead to optimal production while providing safe and environmentally responsible operations.

Wang, Yulun↗
DOE OSTI2021

Observation of ordered organic capping ligands on semiconducting quantum dots via powder X-ray diffraction

Abstract Powder X-ray diffraction is one of the key techniques used to characterize the inorganic structure of colloidal nanocrystals. The comparatively low scattering factor of nuclei of the organic capping ligands and their propensity to be disordered has led investigators to typically consider them effectively invisible to this technique. In this report, we demonstrate that a commonly observed powder X-ray diffraction peak around $$q=1.4{\AA}^{-1}$$ q = 1.4 Å − 1 observed in many small, colloidal quantum dots can be assigned to well-ordered aliphatic ligands bound to and capping the nanocrystals. This conclusion differs from a variety of explanations ascribed by previous sources, the majority of which propose an excess of organic material. Additionally, we demonstrate that the observed ligand peak is a sensitive probe of ligand shell ordering. Changes as a function of ligand length, geometry, and temperature can all be readily observed by X-ray diffraction and manipulated to achieve desired outcomes for the final colloidal system.

36 MATERIALS SCIENCE↗
DOE OSTI2024

A Scalable & Non-Destructive Characterization Strategy to Study Semiconductor/Dielectric Interfaces and Predict Wafer-Level Device Performance

The defect density present at the dielectric-semiconductor interface in an MOS structure directly influences the channel carrier characteristics in semiconductor devices, especially in wide bandgap material systems used in power devices. While these trap defects are typically quantified through electrical characterization of MOS-capacitor test structures, this treatment offers very little insight into the physical nature of interface defects. Such shortcomings demand a physical characterization strategy to guide fabrication optimization. X-ray photoelectron spectroscopy (XPS) is suggested as a viable technique to determine chemical data for dielectric interfaces formed using atomic layer deposition (ALD) on GaN substrates. Previously, 1-D XPS characterization has confirmed the presence of a Ga x O y interlayer between ALD dielectrics and the GaN substrate. In this work, XPS data is serially collected to form 2-D images of an ALD-Al 2 O 3 /GaN interface as a proof-of-concept experiment for in-situ XPS quality monitoring during ALD processing. The information provided by this work reveals some of the challenges for incorporating XPS characterization as an in-situ strategy during fabrication of GaN-based devices. Separately, electrical mapping of a 2-D array of ALD-Al 2 O 3 /GaN MOS-capacitor devices provide a means to quantify the spatial variations in interface quality across a single wafer. Physical characterization techniques, such as time-of-flight secondary ion mass spectroscopy, provide additional chemical information about the Al 2 O 3 /Ga x O y /GaN structure that complement the electrical mapping results. This analysis shows that a higher Ga x O y content correlates with higher interface state defects for trap energies deep in the band gap.

42 ENGINEERING↗
DOE OSTI2023

Internal defect detection and characterization of samarium-cobalt sintered magnets by ultrasonic testing technique

Excessive quantities of samarium-cobalt (Sm-Co) magnet material are being scrapped needlessly due to a lack of understanding of inhomogeneity distribution and unacceptable internal defects. If there is a way to identify, locate, characterize and when needed separate the defective portions of magnet material, utilization can be increased and product quality improved. Further, the magnets’ magnetic and mechanical performance can be improved by reducing the occurrence of internal defects. This paper reports on a cost-effective and efficient nondestructive evaluation method based on an ultrasonic testing (UT) technique applied for detecting and characterizing internal defects in Sm-Co sintered magnets. Applying the UT technique will allow users to comprehensively analyze internal defects, such as inclusions, porosity, microcracks, and other structural irregularities, check for homogeneity and anomalous regions and give the locations of these internal anomalies and defects within the Sm-Co sintered magnets. The UT technique can also be applied to other rare-earth permanent magnets, such as sintered or die-upset neodymium-iron-boron (Nd-Fe-B) magnets. The UT technique can effectively guide quality control and acceptable product selection, in addition to optimizing the magnet alloy design and production processes. Therefore, it can facilitate the improvement of magnet manufacturing efficiency and machinability, reduce scrap, prolong service life, increase the use of what would be post-production waste, and enhance product reuse and recycling at end-of-life disposition.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Improving Subsurface Stress Characterization for Carbon Dioxide Storage Projects by Incorporating Machine Learning Techniques

The overall objective of this project is to develop a framework for reliable characterization and prediction of the state of stress in the overburden and underburden (including the basement) in CO 2 storage reservoirs using machine learning and integrated geomechanics and geophysical methods. Specifically, we propose to develop workflow encompassing of technologies and/or methods to predict stress and pressure changes due to CO 2 injection in an active tertiary recovery site and their impacts on subtle fault activation, fractures and occurrence of microseismic events and compare responses to field observations. In this project, we anticipate using dataset from the Farnsworth field Unit (FWU) which is operated by Purdure Petroleum. A novel elastic-waveform VSP inversion technique will be used to estimate high-resolution spatial and temporal changes of elastic moduli in CO 2 storage reservoirs, which will be combined with velocity-stress relationship derived from laboratory tests to obtain subsurface pressure and stress. Clustered microseismic data will be jointly inverted for improved focal mechanisms. Least-squares reverse-time migration of microseismic waveform data will be performed to directly image fracture/fault zones. Additionally, a deep neural network machine learning technique with convolutional and recurrent layers will be used for learning the spectro-temporal structures in microseismic waveforms. The results of this geotechnical data analysis will be integrated to develop a high-resolution 3D mechanical earth model extending from the overburden sealing formations to the underburden including the basement. Mechanical properties will be derived through integration of mechanical logs, tests, available results from chemo-mechanical laboratory tests, and elastic inversion of seismic data using a combination of Bayesian and stochastic methods as well as machine learning technique. Failure features (faults/fractures) will be represented and/or modeled based on seismic and core data analysis. A transient hydrodynamic-geomechanical model will be developed through coupling with the calibrated FWU reservoir simulation model. The full physics coupled model will be used to train a reduced order proxy model using machine learning algorithm for estimating stress which will then be used with appropriate constitutive relationships and forward seismological models to simulate pressure changes and induced microseismicity. An advanced optimization framework will be developed to perform a history match to minimize error between field observations and simulated. The history matched proxy model will be verified against the full-physics equivalent. The field observations that will be used in the coupled model calibration process include pressure/stress inverted from VSP, moment magnitude from microseismic analysis, real time downhole pressure measurements, production and injection data. Parameter sensitivity and uncertainty analysis will be performed to characterize the impact of model parameter uncertainty on stress estimates. The proposed project will have significant impact on future field implementation of the proposed technology. Because the project field site is an ongoing CO 2 EOR development, the value of the new technology will be demonstrated in an operational context and evaluated as a viable risk mitigation strategy. Cost/benefit will be evaluated together with the various commercial incentives for CO 2 sequestration available to oil and gas operators. The extensive available dataset and ongoing data acquisition under the SWP Phase III work plan provides flexibility for investigation of multiple approaches and reduces technical risk.

58 GEOSCIENCES↗
DOE OSTI2020

Successes and Opportunities for Discovery of Metal Oxide Photoanodes for Solar Fuels Generators

We report that the importance of metal oxide photoanodes in solar fuels technology has garnered concerted efforts in photoanode discovery in recent decades, which complement parallel efforts in development of analytical techniques and optimization strategies using standard photoanodes such as TiO 2 , Fe 2 O 3 and BiVO 4 . Theoretical guidance of high-throughput experiments has been particularly effective in dramatically increasing the portfolio of metal oxide photoanodes, motivating a new era of photoanode development where the characterization and optimization techniques developed on traditional materials are applied to nascent photoanodes that exhibit visible light photoresponse. The compendium of metal oxide photoanodes presented in the present work can also serve as the basis for further technique development, with a primary goal to establish workflows for discovery of materials that perform better against the critical criteria of operational stability, visible light photoresponse, and photovoltage suitable for tandem absorber architectures.

14 SOLAR ENERGY↗
DOE OSTI2021

Microscopic and Macroscopic Characterization of Grain Boundary Energy and Strength in Silicon Carbide via Machine-Learning Techniques

Predicting the properties of grain boundaries poses a challenge because of the complex relationships between structural and chemical attributes both at the atomic and continuum scales. Grain boundary systems are typically characterized by parameters used to classify local atomic arrangements in order to extract features such as grain boundary energy or grain boundary strength. The present work utilizes a combination of high-throughput atomistic simulations, macroscopic and microscopic descriptors, and machine-learning techniques to characterize the energy and strength of silicon carbide grain boundaries. Additionally, a diverse data set of symmetric tilt and twist grain boundaries are described using macroscopic metrics such as misorientation, the alignment of critical low-index planes, and the Schmid factor, but also in terms of microscopic metrics, by quantifying the local atomic structure and chemistry at the interface. These descriptors are used to create random-forest regression models, allowing for their relative importance to the grain boundary energy and decohesion stress to be better understood. Results show that while the energetics of the grain boundary were best described using the microscopic descriptors, the ability of the macroscopic descriptors to reasonably predict grain boundaries with low energy suggests a link between the crystallographic orientation and the resultant atomic structure that forms at the grain boundary within this regime. For grain boundary strength, neither microscopic nor macroscopic descriptors were able to fully capture the response individually. However, when both descriptor sets were utilized, the decohesion stress of the grain boundary could be accurately predicted. These results highlight the importance of considering both macroscopic and microscopic factors when constructing constitutive models for grain boundary systems, which has significant implications for both understanding the fundamental mechanisms at work and the ability to bridge length scales.

36 MATERIALS SCIENCE↗