Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “boundary layer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41
All sourcesNASA NTRSDOE OSTI
NASA NTRS1930

The boundary layer as a means of controlling the flow of liquids and gases

According to one of the main propositions of the boundary layer theory the scarcely noticeable boundary layer may, under certain conditions, have a decisive influence on the form of the external flow by causing it to separate from the wing surface. These phenomena are known to be caused by a kind of stagnation of the boundary layer at the point of separation. The present report deals with similar phenomena. It is important to note that usually the cause (external interference) directly affects only the layer close to the wall, while its indirect effect extends to a large portion of the external flow.

Schrenk, Oskar↗
NASA NTRS2018

Aeromechanics Analysis of a Distortion-Tolerant Fan with Boundary Layer Ingestion

A propulsion system with Boundary Layer Ingestion (BLI) has the potential to significantly reduce aircraft engine fuel burn. But a critical challenge is to design a fan that can operate continuously with a persistent BLI distortion without aeromechanical failure -- flutter or high cycle fatigue due to forced response. High-fidelity computational aeromechanics analysis can be very valuable to support the design of a fan that has satisfactory aeromechanic characteristics and good aerodynamic performance and operability. Detailed aeromechanics analyses together with careful monitoring of the test article is necessary to avoid unexpected problems or failures during testing. In the present work, an aeromechanics analysis based on a three-dimensional, time-accurate, Reynolds-averaged Navier-Stokes computational fluid dynamics code is used to study the performance and aeromechanical characteristics of the fan in both circumferentially-uniform and circumferentially-varying distorted flows. Pre-test aeromechanics analyses are used to prepare for the wind tunnel test and comparisons are made with measured blade vibration data after the test. The analysis shows that the fan has low levels of aerodynamic damping at various operating conditions examined. In the test, the fan remained free of flutter except at one near-stall operating condition. Analysis could not be performed at this low mass flow rate operating condition since it fell beyond the limit of numerical stability of the analysis code. The measured resonant forced response at a specific low-response crossing indicated that the analysis under-predicted this response and work is in progress to understand possible sources of differences and to analyze other larger resonant responses. Follow-on work is also planned with a coupled inlet-fan aeromechanics analysis that will more accurately represent the interactions between the fan and BLI distortion.

Propulsion Aeroelasticity↗
NASA NTRS1976

Calculation methods for compressible turbulent boundary layers

Calculation procedures for non-reacting compressible two- and three-dimensional turbulent boundary layers were reviewed. Integral, transformation and correlation methods, as well as finite difference solutions of the complete boundary layer equations summarized. Alternative numerical solution procedures were examined, and both mean field and mean turbulence field closure models were considered. Physics and related calculation problems peculiar to compressible turbulent boundary layers are described. A catalog of available solution procedures of the finite difference, finite element, and method of weighted residuals genre is included. Influence of compressibility, low Reynolds number, wall blowing, and pressure gradient upon mean field closure constants are reported.

Bushnell, D. M.↗
NASA NTRS1949

Exact Calculation of Laminar Boundary Layer in Longitudinal Flow over a Flat Plate with Homogeneous Suction

Lately it has been proposed to reduce the friction drag of a body in a flow for the technically important large Reynolds numbers by the following expedient: the boundary layer, normally turbulent, is artificially kept laminar up to high Reynolds numbers by suction. The reduction in friction drag thus obtained is of the order of magnitude of 60 to 80 percent of the turbulent friction drag, since the latter, for large Reynolds numbers, is several times the laminar friction drag. In considering the idea mentioned one has first to consider whether suction is a possible means of keeping the boundary layer laminar. This question can be answered by a theoretical investigation of the stability of the laminar boundary layer with suction. A knowledge, as accurate as possible, of the velocity distribution in the laminar boundary layer with suction forms the starting point for the stability investigation. E. Schlichting recently gave a survey of the present state of calculation of the laminar boundary layer with suction.

Iglisch, Rudolf↗
NASA NTRS1986

Boundary layer flow visualization for flight testing

Flow visualization is used extensively in flight testing to determine aerodynamic characteristics such as surface flow direction and boundary layer state. Several visualization techniques are available to the aerodynamicist. Two of the most popular are oil flows and sublimating chemicals. Oil is used to visualize boundary layer transition, shock wave location, regions of separated flow, and surface flow direction. Boundary layer transition can also be visualized with sublimating chemicals. A summary of these two techniques is discussed, and the use of sublimating chemicals is examined in some detail. The different modes of boundary layer transition are characterized by different patterns in the sublimating chemical coating. The discussion includes interpretation of these chemical patterns and the temperature and velocity operating limitations of the chemical substances. Information for selection of appropriate chemicals for a desired set of flight conditions is provided.

Obara, Clifford J.↗
NASA NTRS1988

Goertler vortices in supersonic boundary layers

The problem of Goertler vortices in compressible boundary layers over concave walls is studied by solving parabolic partial differential equations. The numerical scheme used is based upon a fourth-order accurate compact difference scheme. The results show that both the velocity and temperature fluctuations may lead to a Goertler vortex. The vortex growth rates determined from the present method are found to differ somewhat from those given by normal mode solution. The effects of cooling, heating and pressure gradient are also studied. At a Mach number of 3.5, cooling has a small destabilizing effect. The effect of adverse pressure gradient is also found to be destabilizing on a Mach 8 boundary layer.

Spall, R. E.↗
NASA NTRS1992

Turbulent heat flux measurements in a transitional boundary layer

During an experimental investigation of the transitional boundary layer over a heated flat plate, an unexpected result was encountered for the turbulent heat flux (bar-v't'). This quantity, representing the correlation between the fluctuating normal velocity and the temperature, was measured to be negative near the wall under certain conditions. The result was unexpected as it implied a counter-gradient heat transfer by the turbulent fluctuations. Possible reasons for this anomalous result were further investigated. The possible causes considered for this negative bar-v't' were: (1) plausible measurement error and peculiarity of the flow facility, (2) large probe size effect, (3) 'streaky structure' in the near wall boundary layer, and (4) contributions from other terms usually assumed negligible in the energy equation including the Reynolds heat flux in the streamwise direction (bar-u't'). Even though the energy balance has remained inconclusive, none of the items (1) to (3) appear to be contributing directly to the anomaly.

Sohn, K. H.↗
NASA NTRS1982

Turbulent boundary layer heat transfer experiments: Convex curvature effects including introduction and recovery

Measurements were made of the heat transfer rate through turbulent and transitional boundary layers on an isothermal, convexly curved wall and downstream flat plate. The effect of convex curvature on the fully turbulent boundary layer was a reduction of the local Stanton numbers 20% to 50% below those predicted for a flat wall under the same circumstances. The recovery of the heat transfer rates on the downstream flat wall was extremely slow. After 60 cm of recovery length, the Stanton number was still typically 15% to 20% below the flat wall predicted value. Various effects important in the modeling of curved flows were studied separately. These are: the effect of initial boundary layer thickness, the effect of freestream velocity, the effect of freestream acceleration, the effect of unheated starting length, and the effect of the maturity of the boundary layer. An existing curvature prediction model was tested against this broad heat transfer data base to determine where it could appropriately be used for heat transfer predictions.

Simon, T. W.↗
NASA NTRS1978

Effect of wall temperature on a supersonic turbulent boundary layer

Measurement of mean flow profiles in a fully developed Mach 3 turbulent boundary layer with negligible pressure gradient is reported. Data were acquired at several streamwise locations for wall-to-total temperature ratios of 0.94, 0.71, and 0.54. The results demonstrate that the velocity defect formulation of the law-of-the-wake, which successfully correlates compressible, adiabatic boundary layers, is also valid for nonadiabatic flows. It is also shown that for adiabatic walls, the linear Crocco relation between total temperature and velocity does not provide a valid test of the nature of the boundary-layer flow for practical cases where the Prandtl number departs from unity. Finally, the turbulent shear stress, mixing length, and eddy viscosity were extracted from the 'time-averaged' conservation equations using the measured mean flow profiles and found to be insensitive to wall temperature. In particular, the latter properties are in good agreement with earlier compressible, adiabatic correlations of turbulent transport properties.

Laderman, A. J.↗
NASA NTRS1988

Wind tunnel-sidewall-boundary-layer effects in transonic airfoil testing-some correctable, but some not

The need to correct transonic airfoil wind tunnel test data for the influence of the tunnel sidewall boundary layers, in addition to the wall accepted corrections for the analytical investigation was carried out in order to evaluate sidewall boundary layer effects on transonic airfoil characteristics, and to validate proposed correction and the limit to their applications. This investigation involved testing of modern airfoil configurations in two different transonic airfoil test facilities, the 15 x 60 inch two-dimensional insert of the National Aeronautical Establishment (NAE) 5 foot tunnel in Ottawa, Canada, and the two-dimensional test section of the NASA Langley 0.3 m Transonic Cryogenic Tunnel (TCT). Results presented included effects of variations in sidewall-boundary layer bleed in both facilities, different sidewall boundary layer correction procedures, tunnel-to tunnel comparisons of correcte results, and flow conditions with and without separation.

Lynch, F. T.↗
NASA NTRS1978

Transitional Boundary-Layer Solutions Using a Mixing-Length and a Two-Equation Turbulence Model

Boundary-layer solutions were obtained using the conventional two-layer mixing-length turbulence model and the Wilcox-Traci two-equation model of turbulence. Both flatplate and blunt-body geometries were considered. The most significant result of the study is development of approximations for the two-equation model which permit streamwise stepsize comparable to that used in mixing-length computations. Additionally, a set of model-equation boundary conditions derived which apply equally well to both flat-plate and blunt-body geometries. Solutions obtained with the two-equations turbulence model are compared with experimental data and/or corresponding solutions obtained using the mixing-length model. Agreement is satisfactory for flat-plate boundary layers but not for blunt body boundary layers.

Anderson, E. C.↗
NASA NTRS1975

Boundary layer control for airships

An investigation is summarized of the aerodynamic principle of boundary layer control for nonrigid LTA craft. The project included a wind tunnel test on a BLC body of revolution at zero angle of attack. Theoretical analysis is shown to be in excellent agreement with the test data. Methods are evolved for predicting the boundary layer development on a body of revolution and the suction pumping and propulsive power requirements. These methods are used to predict the performance characteristics of a full-scale airship. The analysis indicates that propulsive power reductions of 15 to 25 percent and endurance improvements of 20 to 40 percent may be realized in employing boundary-layer control to nonrigid airships.

Pake, F. A.↗
NASA NTRS2000

Design and Evaluation of a New Boundary-Layer Rake for Flight Testing

A new boundary-layer rake has been designed and built for flight testing on the NASA Dryden Flight Research Center F-15B/Flight Test Fixture. A feature unique to this rake is its curved body, which allows pitot tubes to be more densely clustered in the near-wall region than conventional rakes allow. This curved rake design has a complex three-dimensional shape that requires innovative solid-modeling and machining techniques. Finite-element stress analysis of the new design shows high factors of safety. The rake has passed a ground test in which random vibration measuring 12 g rms was applied for 20 min in each of the three normal directions. Aerodynamic evaluation of the rake has been conducted in the NASA Glenn Research Center 8 x 6 Supersonic Wind Tunnel at Mach 0-2. The pitot pressures from the new rake agree with conventional rake data over the range of Mach numbers tested. The boundary-layer profiles computed from the rake data have been shown to have the standard logarithmic-law profile. Skin friction values computed from the rake data using the Clauser plot method agree with the Preston tube results and the van Driest II compressible skin friction correlation to approximately +/-5 percent.

Bui, Trong T.↗
NASA NTRS2018

Aerodynamic Conceptual Design of Boundary Layer Ingestion Propulsor Systems: A Quasi-2D Through Flow Analysis Method and Multi-Fidelity Propulsor Design Framework

A propulsor design framework for maximizing the benefits of boundary layer ingestion is presented. The performance of BLI is strongly affected by all propulsor components, including the boundary layer characteristics (displacement thickness and form factor) of the ingested boundary layer at the inlet, the radical loading characteristics if the fan and exit guide vane (EGV), the area contraction from inlet to nozzle, and flow expansion at the exhaust cone. A strategy and it's associated multi-fidelity design framework are proposed for an efficient conceptual design of the BLI proplusor which inherently differs from the conventional engine. In the frame work, a quasi-2D through flow model served as the underlying fidelity model is introduced to incorporate the radial effect of the boundary layer entering the propulsor. Multi-fidelity design work is conducted to maximize the predefined performance metrics. On top of this efficient quasi-2D model. computational fluid dynamics based 3-D propulsor models are implemented to refine and validate the design. A BLI propulsion system integrated with fuselage is designed to showcase the framework. The performance of the resulting BLI propulsor system is evaluated via body-force model in unstructured Reynolds-Averaged Navier-Stoke (RANS) CFD and improvement is presented.

Lee, B. J.↗
NASA NTRS1985

On the Improvement of Satellite Temperature Retrievals by Means of Boundary Layer Models

The improvement of the accuracy of the satellite temperature retrievals close to the Earth's surface by boundary layer models was determined. The simplest type of boundary layer models that only consider time changes in the mean boundary layer quantities such as equivalent potential temperature and specific humidity, but neglect the details of the turbulent structure in the interior of the layer were used. They can be run with relatively few externally specified parameters: surface wind speed and divergence rate. Model verifications studies show that under certain conditions the mean atmospheric structure can be simulated very well.

Boers, R.↗
NASA NTRS2016

Acoustic Radiation From a Mach 14 Turbulent Boundary Layer

Direct numerical simulations (DNS) are used to examine the turbulence statistics and the radiation field generated by a high-speed turbulent boundary layer with a nominal freestream Mach number of 14 and wall temperature of 0:18 times the recovery temperature. The flow conditions fall within the range of nozzle exit conditions of the Arnold Engineering Development Center (AEDC) Hypervelocity Tunnel No. 9 facility. The streamwise domain size is approximately 200 times the boundary-layer thickness at the inlet, with a useful range of Reynolds number corresponding to Re 450 􀀀 650. Consistent with previous studies of turbulent boundary layer at high Mach numbers, the weak compressibility hypothesis for turbulent boundary layers remains applicable under this flow condition and the computational results confirm the validity of both the van Driest transformation and Morkovin's scaling. The Reynolds analogy is valid at the surface; the RMS of fluctuations in the surface pressure, wall shear stress, and heat flux is 24%, 53%, and 67% of the surface mean, respectively. The magnitude and dominant frequency of pressure fluctuations are found to vary dramatically within the inner layer (z/delta 0.< or approx. 0.08 or z+ < or approx. 50). The peak of the pre-multiplied frequency spectrum of the pressure fluctuation is f(delta)/U(sub infinity) approx. 2.1 at the surface and shifts to a lower frequency of f(delta)/U(sub infinity) approx. 0.7 in the free stream where the pressure signal is predominantly acoustic. The dominant frequency of the pressure spectrum shows a significant dependence on the freestream Mach number both at the wall and in the free stream.

Zhang, Chao↗
NASA NTRS1987

Boundary-layer equations in generalized curvilinear coordinates

A set of higher-order boundary-layer equations is derived valid for three-dimensional compressible flows. The equations are written in a generalized curvilinear coordinate system, in which the surface coordinates are nonorthogonal; the third axis is restricted to be normal to the surface. Also, higher-order viscous terms which are retained depend on the surface curvature of the body. Thus, the equations are suitable for the calculation of the boundary layer about arbitrary vehicles. As a starting point, the Navier-Stokes equations are derived in a tensorian notation. Then by means of an order-of-magnitude analysis, the boundary-layer equations are developed. To provide an interface between the analytical partial differentiation notation and the compact tensor notation, a brief review of the most essential theorems of the tensor analysis related to the equations of the fluid dynamics is given. Many useful quantities, such as the contravariant and the covariant metrics and the physical velocity components, are written in both notations.

Panaras, Argyris G.↗
NASA NTRS2013

Trip-Induced Transition Measurements in a Hypersonic Boundary Layer Using Molecular Tagging Velocimetry

Measurements of mean streamwise velocity, fluctuating streamwise velocity, and instantaneous streamwise velocity profiles in a hypersonic boundary layer were obtained over a 10-degree half-angle wedge model. A laser-induced fluorescence-based molecular tagging velocimetry technique was used to make the measurements. The nominal edge Mach number was 4.2. Velocity profiles were measured both in an untripped boundary layer and in the wake of a 4-mm diameter cylindrical tripping element centered 75.4 mm downstream of the sharp leading edge. Three different trip heights were investigated: k = 0.53 mm, k = 1.0 mm and k = 2.0 mm. The laminar boundary layer thickness at the position of the measurements was approximately 1 mm, though the exact thickness was dependent on Reynolds number and wall temperature. All of the measurements were made starting from a streamwise location approximately 18 mm downstream of the tripping element. This measurement region continued approximately 30 mm in the streamwise direction. Additionally, measurements were made at several spanwise locations. An analysis of flow features show how the magnitude, spatial location, and spatial growth of streamwise velocity instabilities are affected by parameters such as the ratio of trip height to boundary layer thickness and roughness Reynolds number. The fluctuating component of streamwise velocity measured along the centerline of the model increased from approximately 75 m/s with no trip to +/-225 m/s with a 0.53-mm trip, and to +/-240 m/s with a 1-mm trip, while holding the freestream Reynolds number constant. These measurements were performed in the 31-inch Mach 10 Air Tunnel at the NASA Langley Research Center.

Bathel, Brett F.↗