Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “boundary effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Comparison of supercritical and conventional wing flutter characteristics

A wind-tunnel study is described in which it was attempted to compare the measured flutter boundaries of two dynamically similar aeroelastic models with identical planform, maximum thickness-to-chord ratio, and as nearly identical stiffness and mass distributions as possible, but with one wing having a supercritical airfoil and the other a conventional one. At subsonic Mach numbers, the flutter boundary for the supercritical wing was above that of the conventional wing, as predicted by flutter calculations using subsonic lifting theory. In the transonic region, however, the supercritical wing boundary decreases more rapidly and the minimum flutter point occurs at a dynamic pressure below the conventional wing boundary. Airfoil shape effects may account for some of the difference in the flutter boundaries of the two airfoils.

Farmer, M. G.↗
NASA NTRS1992

On the coupling between a supersonic boundary layer and a flexible surface

The coupling between a two-dimensional, supersonic, laminar boundary layer and a flexible surface is studied using direct numerical computations of the Navier-Stokes equations coupled with the plate equation. The flexible surface is forced to vibrate by plane acoustic waves at normal incidence emanated by a sound source located on the side of the flexible surface opposite to the boundary layer. The effect of the source excitation frequency on the surface vibration and boundary layer stability is analyzed. We find that, for frequencies near the fifth natural frequency of the surface or lower, large disturbances are introduced in the boundary layer which may alter its stability characteristics. The interaction between a stable two-dimensional disturbance of Tollmien-Schlichting (TS) type with the vibrating surface is also studied. We find that the disturbance level is higher over the vibrating flexible surface than that obtained when the surface is rigid, which indicates a strong coupling between flow and structure. However, in the absence of the sound source the disturbance level over the rigid and flexible surfaces are identical. This result is due to the high frequency of the TS disturbance which does not couple with the flexible surface.

Frendi, Abdelkader↗
NASA NTRS1992

On the coupling between a supersonic boundary layer and a flexible surface

The coupling between a two-dimensional, supersonic, laminar boundary layer and a flexible surface is studied using direct numerical computations of the Navier-Stokes equations coupled with the plate equation. The flexible surface is forced to vibrate by plane acoustic waves at normal incidence emanated by a sound source located on the side of the flexible surface opposite to the boundary layer. The effect of the source excitation frequency on the surface vibration and boundary layer stability is analyzed. We find that, for frequencies near the fifth natural frequency of the surface or lower, large disturbances are introduced in the boundary layer which may alter its stability characteristics. The interaction between a stable two-dimensional disturbance of Tollmien-Schlichting (TS) type with the vibrating surface is also studied. We find that the disturbance level is higher over the vrating flexible surface than that obtained when the surface is rig id, which indicates a strong coupling between flow and structure. However, in the absence of the sound source the disturbance level over the rigid and flexible surfaces are identical. This result is due to the high frequency of the TS disturbance which does not couple with the flexible surface.

Frendi, Abdelkader↗
NASA NTRS1959

Effect of Body Perturbations on Hypersonic Flow Over Slender Power Law Bodies

Hypersonic-slender-body theory, in the limit as the free-stream Mach number becomes infinite, is used to find the effect of slightly perturbing the surface of slender two-dimensional and axisymmetric power law bodies, The body perturbations are assumed to have a power law variation (with streamwise distance downstream of the nose of the body). Numerical results are presented for (1) the effect of boundary-layer development on two dimensional and axisymmetric bodies, (2) the effect of very small angles of attack (on tow[dimensional bodies), and (3) the effect of blunting the nose of very slender wedges and cones.

Mirels, Harold↗
NASA NTRS2010

Numerical Simulations of the Boundary Layer Transition Flight Experiment

Computational Fluid Dynamics (CFD) simulations were used to study the possible effects that the Boundary Layer Transition (BLT) Flight Experiments may have on the heating environment of the Space Shuttle during its entry to Earth. To investigate this issue, hypersonic calculations using the Data-Parallel Line Relaxation (DPLR) and Langley Aerothermodynamic Upwind Relaxation (LAURA) CFD codes were computed for a 0.75 tall protuberance at flight conditions of Mach 15 and 18. These initial results showed high surface heating on the BLT trip and the areas surrounding the protuberance. Since the predicted peak heating rates would exceed the thermal limits of the materials selected to construct the BLT trip, many changes to the geometry were attempted in order to reduce the surface heat flux. The following paper describes the various geometry revisions and the resulting heating environments predicted by the CFD codes.

Tang, Chun Y.↗
NASA NTRS1985

An investigation of the effects of the propeller slipstream of a laminar wing boundary layer

A research program is in progress to study the effects of the propeller slipstream on natural laminar flow. Flight and wind tunnel measurements of the wing boundary layer have been made using hot-film velocity sensor probes. The results show the boundary layer, at any given point, to alternate between laminar and turbulent states. This cyclic behavior is due to periodic external flow turbulence originating from the viscous wake of the propeller blades. Analytic studies show the cyclic laminar/turbulent boundary layer to result in a significantly lower wing section drag than a fully turbulent boundary layer. The application of natural laminar flow design philosophy yields drag reduction benefits in the slipstream affected regions of the airframe, as well as the unaffected regions.

Howard, R. M.↗
NASA NTRS1997

Effect of Free Stream Turbulence and Other Vortical Disturbances on a Laminar Boundary Layer

This paper is concerned with the effect of free-stream turbulence on the pretransitional flat-plate boundary layer. It is assumed that either the turbulence Reynolds number or the downstream distance (or both) is small enough so that the flow can be linearized. The dominant disturbances in the boundary layer, which are of the Klebanoff type, are governed by the linearized unsteady boundary-region equations, i.e., the Navier Stokes equations with the streamwise derivatives neglected in the viscous and pressure-gradient terms. The turbulence is represented as a superposition of vortical free-stream Fourier modes, and the corresponding individual Fourier component solutions to the boundary-region equations are obtained numerically. The results are then superposed to compute the root mean square of the fluctuating streamwise velocity in the boundary layer produced by the actual free-stream turbulence. The calculated boundary-layer disturbances are in good quantitative agreement with the experimentally observed Klebanoff modes when strong low-frequency anisotropic effects are included in the free-stream turbulence spectrum. We discuss some additional effects that may need to be accounted for in order to obtain a complete description of the Klebanoff modes.

Goldstein, Marvin E.↗
NASA NTRS1974

Use of multiple discrete wall jets for delaying boundary layer separation

The effectiveness of a spanwise array of small discrete blowing nozzles in preventing separation of a turbulent boundary layer was investigated experimentally. The spacing, axial location, and momentum flux of the nozzles were varied in a systematic way, and overall performance was measured for each combination. Extensive mean velocity profiles were measured for one selected combination. Overall diffusion achieved before separation was correlated successfully with a momentum flux excess parameter, and in terms of this parameter discrete nozzles, when advantageously placed, were found to perform somewhat better than an optimally placed two-dimensional jet slot.

Mclean, J. D.↗
NASA NTRS1981

The effect of oxygen concentration on the boundary-lubricating characteristics of a C ether and a polyphenyl ether to 300 C

Ball-on-disk sliding friction experiments were carried out at 17 m/min (100 rev/min) to investigate the effect of oxygen concentration varying from 20% (air) to 0.001% (nitrogen) on the boundary-lubricating characteristics of an unformulated C ether in the temperature range 20-300 C. Results were then compared with those obtained for a five-ring polyphenylether in air and in nitrogen. The C ether yielded lower wear and lower friction coefficients than a five-ring polyphenylether in both air and nitrogen over most of the temperature range. Friction polymer was observed around the wear scars of most test specimens, with much greater quantities of friction polymer produced in a low-oxygen environment. Thus, with respect to friction polymer production, the C ether behaved very much like the polyphenylether.

Jones, W. R., Jr.↗
NASA NTRS1981

Effect of driven-wall motion on a turbulent boundary layer

An acoustically driven wall model with amplitudes greater than 0.01 cm was used to study the effect of unsteady wall boundary conditions on the structure of a zero-pressure-gradient turbulent boundary layer. Hot-wire measurements showed large variations in fluctuation quantities (including Reynolds stress) along each model wave. These longitudinal variations decreased rapidly with increasing distance from the driven wall, but the average level of these fluctuations decreased only slightly even outside the boundary layer. When the acoustical fluctuations were subtracted, the remaining fluctuations were essentially the same as for the undriven model. It is concluded that there is no significant interaction between the acoustic and turbulent fluctuations.

Weinstein, L. M.↗
NASA NTRS1994

Navier-Stokes simulations of the effects of suction holes on a flat plate boundary layer

Direct numerical simulations (DNS) of the Navier-Stokes equations are employed to explore the effects of suction holes on transition in a laminar flat plate boundary layer. The Navier-Stokes equations are cast in vorticity-velocity form. Periodicity is imposed in spanwise direction; all other spatial derivatives are discretized with fourth order compact differences. An explicit fourth order Runge-Kutta scheme is employed for the time-integration of the vorticity transport equations. Suction is applied through a row of holes aligned in spanwise direction. For low suction strengths, each hole generates a pair of stable streamwise vortices. When the suction strength exceeds a critical value, the vortices become unstable. For high suction strengths, vortex shedding occurs right at the suction holes. Our numerical findings agree well with experimental observations.

Meitz, Hubert L.↗
NASA NTRS1978

Effect of perturbed flow on the transition from the supersonic laminar boundary layer to the turbulent

Results of experimental studies on the effect of various factors on the transition of a supersonic boundary layer are discussed. It is shown that in supersonic wind tunnels, a significant effect on the transition of the boundary layer on a model is exerted by the scale of acoustic perturbations, which is proportional to the boundary layer displacement thickness of the working section. Experimental data obtained over a wide range of variation of flow parameters in aerodynamically similar test installations with different dimensions of the working section are generalized by means of a correlation parameter based on the displacement thickness.

Kharitonov, A. M.↗
NASA NTRS1983

A study of the effects of Lebu devices on turbulent boundary layer drag

Initial measurements of the changes in local skin friction, velocity profile shape, and turbulence structure which result from the placement of tandem plates parallel to the wall in the outer region of thick turbulent boundary layers were made. Using a tunnel with a .75 m x 1.2 m x 7.3 m test section, which diverged so as to keep the pressure gradient less than 2x1000/ft, on the test wall, a skin friction reduction of approximately 30% was measured at xi/h = 62. This relaxed to a reduction of approximately 16% at xi/h = 124 for h/delta M = .6. The c sub f measurements for both the normal and modified boundary layers were obtained by measuring the slope of the velocity profile within the linear sublayer. Visual results indicated a continued presence of strong large eddy structure downstream of the devices. Local skin friction reduction of 12% at xi/h = 62 was also obtained with the manipulators above the boundary layer at y/delta m = 1.1.

Falco, R. E.↗
NASA NTRS1985

Numerical study of large-eddy breakup and its effect on the drag characteristics of boundary layers

The break-up of a field of eddies by a flat-plate obstacle embedded in a boundary layer is studied using numerical solutions to the two-dimensional Navier-Stokes equations. The flow is taken to be incompressible and unsteady. The flow field is initiated from rest. A train of eddies of predetermined size and strength are swept into the computational domain upstream of the plate. The undisturbed velocity profile is given by the Blasius solution. The disturbance vorticity generated at the plate and wall, plus that introduced with the eddies, mix with the background vorticity and is transported throughout the entire flow. All quantities are scaled by the plate length, the unidsturbed free-stream velocity, and the fluid kinematic viscosity. The Reynolds number is 1000, the Blasius boundary layer thickness is 2.0, and the plate is positioned a distance of 1.0 above the wall. The computational domain is four units high and sixteen units long.

Kinney, R. B.↗
NASA NTRS1986

Field study of the effect of orographic features on planetary boundary layer models

A flight program to measure the influence of orographic features on turbulent momentum, heat, and moisture fluxes was carried out. Characteristic wake flow patterns were observed in laboratory studies. While the upper level winds (above 10,000 ft msl) blow from west to east (perpendicular to the mountain range), flow patterns similar to flow from a backward-facing step are observed. When the upper level winds blow at 301 and 312 deg from true north (slightly oblique to the mountain range), experimental evidence suggests flow patterns typical of a vortex shed from the mountain range similar to a leading edge vortex from a delta wing aircraft. The observed flow patterns are analyzed. It is concluded that wake flow very similar to those observed in laboratory facilities can occur due to winds over mountain ranges. Results of studies in the laboratory may shed considerable insight to atmospheric boundary layer winds obstructed by orographic features.

Frost, Walter↗