Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Wing loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

Aerodynamic Loading Characteristics Including Effects of Aeroelasticity of a Thin-Trapezoidal-Wing-Body Combination at Mach Number of 1.43

Results have been obtained in the Langley 8-foot transonic pressure tunnel at a Mach number of 1.43 and at angles of attack from 0 deg to about 24 deg which indicate the static-aerodynamic-loads characteristics for a 2-percent-thick trapezoidal wing in combination with a body. Included are the effects of changing Reynolds number and of fixing boundary-layer transition. The results show that aerodynamic loading characteristics at a Mach number of 1.43 are similar to those reported in NACA RM L56Jl2a for the same configuration at a Mach number of 1.115. Reducing the Reynolds number resulted in reductions in the deflection of the wing and caused a slight increase in the relative loading over the outboard wing sections since the deflections were in a direction to unload the tip sections. Little or no effects were seen to result from fixing boundary-layer transition at a tunnel stagnation pressure of 1,950 pounds per square foot.

Kelly, Thomas C.↗

Dynamic deformation and fracture of single crystal silicon: Fracture modes, damage laws, and anisotropy

Impact fracture of single-crystal Si is critical to long-term reliability of electronic devices and solar cells for its wide use as components or substrates in semiconductor industry. Single-crystal Si is loaded along two different crystallographic directions with a split Hopkinson pressure bar integrated with an in situ x-ray imaging and diffraction system. Bulk stress histories are measured, simultaneously with x-ray phase contrast imaging (XPCI) and Laue diffraction. Damage evolution is quantified with grayscale maps from XPCI. Single-crystal Si exhibits pronounced anisotropy in fracture modes, and thus fracture strengths and damage evolution. For loading along [11¯ 0] and viewing along [001], (1¯1¯0)[11¯ 0] cleavage is activated and induces horizontal primary cracks followed by perpendicular wing cracks. However, for loading along [011¯] and viewing along [111], random nucleation and growth of shear and tensile-splitting crack networks lead to catastrophic failure of materials with no cleavage. The primary-wing crack mode leads to a lower characteristic fracture strength due to predamage, but a more concentrated strength distribution, i.e., a higher Weibull modulus, compared to the second loading case. Furthermore, the sequential primary cracking, wing cracking and wing-crack coalescence processes result in a gradual increase of damage with time, deviating from theoretical predictions. Particle size and aspect ratios of fragments are discussed with postmortem fragment analysis, which verifies fracture modes observed in XPCI.

36 MATERIALS SCIENCE↗

Numerical investigation of performance degradation of wings and rotors due to icing

The aerodynamic load characteristics and the performance degradation of moderate aspect ratio wings and rotors with simulated glaze leading-edge ice have been studied using a three-dimensional, compressible Navier-Stokes solver. The effect of a splitter plate at the wing root on both clean and iced wing configurations has been studied and the results are compared with the experiment. A significant difference has been observed with and without splitter plates in the magnitude of flow separation and aerodynamic loading at the inboard stations for the iced wing at 8-deg angle of attack. Inviscid calculations were performed and compared with viscous calculations to investigate whether the performance of iced swept wings can be inexpensively predicted using Euler methods. It is shown that inviscid calculations predict higher aerodynamic loading than viscous calculations, and cannot model separation effects. A typical nonlifting helicopter rotor in forward flight condition is also studied, and the penalty due to the leading-edge ice formation on the required torque is numerically demonstrated.

Kwon, Oh J.↗

Effect of a Nacelle on the Low-speed Aerodynamic Characteristics of a Swept-back Wing

Wind-tunnel tests of a simplified nacelle on a semispan wing having approximately 35 degrees of sweepback were made at low speeds to evaluate the effects of the nacelle on the aerodynamic characteristics of the wing. Force, moment, and pressure-distribution measurements are presented for the nacelle underslung and centrally mounted on the wing and mounted on a strut below the wing.

WING-NACELLE COMBINATIONS - AIRPLANES↗

The influence of time dependent flight and maneuver velocities and elastic or viscoelastic flexibilities on aerodynamic and stability derivatives

The advent of new structural concepts employing composites in primary load carrying aerospace structures in UAVs, MAVs, Boeing 787s, Airbus A380s, etc., necessitates the inclusion of flexibility as well as viscoelasticity in static structural and aero-viscoelastic analyses. Differences and similarities between aeroelasticity and aero-viscoelasticity have been investigated in [2]. An investigation is undertaken as to the dependence and sensitivity of aerodynamic and stability derivatives to elastic and viscoelastic structural flexibility and as to time dependent flight and maneuver velocities. Longitudinal, lateral and directional stabilities are investigated. It has been a well established fact that elastic lifting surfaces are subject to loss of control effectiveness and control reversal at certain flight speeds, which depend on aerodynamic, structural and material properties [5]. Such elastic analyses are extended to linear viscoelastic materials under quasi-static, dynamic, and sudden and gradual loading conditions. In elastic wings one of the critical static parameters is the velocity at which control reversal takes place (V{sub REV}{sup E}). Since elastic formulations constitute viscoelastic initial conditions, viscoelastic reversal may occur at speeds V{sub REV<}{sup ≧}V{sub REV}{sup E}, but furthermore does so in time at 0 < t{sub REV} ≤ ∞. The influence of the twin effects of viscoelastic and elastic materials and of variable flight velocities on longitudinal, lateral, directional and spin stabilities are also investigated. It has been a well established fact that elastic lifting surfaces are subject to loss of control effectiveness and control reversal at certain flight speeds, which depend on aerodynamic, structural and material properties [5]. Such elastic analyses are here extended to linear viscoelastic materials under quasi-static, dynamic, and sudden and gradual loading conditions. In elastic wings the critical parameter is the velocity at which control reversal takes place (V{sub REV}{sup E}). Since elastic formulations constitute viscoelastic initial conditions, viscoelastic reversal may occur at speeds V{sub REV<}{sup ≧}V{sub REV}{sup E}, but furthermore does so in time at 0 < t{sub REV} ≤ ∞. This paper reports on analytical analyses and simulations of the effects of flexibility and time dependent material properties (viscoelasticity) on aerodynamic derivatives and on lateral, longitudinal, directional and spin stability derivatives. Cases of both constant and variable flight and maneuver velocities are considered. Analytical results for maneuvers involving constant and time dependent rolling velocities are analyzed, discussed and evaluated. The relationships between rolling velocity p and aileron angular displacement β as well as control effectiveness are analyzed and discussed in detail for elastic and viscoelastic wings. Such analyses establish the roll effectiveness derivatives (∂[p(t)])/(V{sub ∞}∂β(t)) . Similar studies involving other stability and aerodynamic derivatives are also undertaken. The influence of the twin effects of viscoelastic and elastic materials and of variable flight, rolling, pitching and yawing velocities on longitudinal, lateral and directional are also investigated. Variable flight velocities, encountered during maneuvers, render the usually linear problem at constant velocities into a nonlinear one.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Investigation at Low Speeds of Deflectors and Spoilers as Gust Alleviators on a Model of the Bell X-5 Airplane with 35 Degree Swept Wings and on a High-aspect-ratio 35 Degree Swept-wing-fuselage Model

Results of an investigation at low speeds to determine the gust-alleviation capabilities (reduction in lift-curve slope) of spoilers and deflectors on a 35 degree swept-wing model of high aspect ratio and on a 1/4-scale model of the X-5 airplane with 35 degree swept wings indicate that deflector and spoiler-deflector types of controls can be designed to provide considerable gust alleviation for a swept-wing airplane while still maintaining stability and control.

CONTROLS, SPOILER - COMPLETE WINGS↗

Transonic Cruise Slotted Wing Design for Commercial Transport Aircraft using CDISC

A knowledge-based aerodynamic design method, CDISC, has been extended to enable the computational design of transonic cruise slotted wings for commercial transport aircraft. The cruise slotted wing is a multielement wing concept with a forward main element and an aft flap element, separated to form an intermediate slot. This slot favorably redirects airflow from the main element lower surface toward the low-momentum, upper-surface boundary layer of the flap. Relative to the supercritical wing, the cruise slotted wing enables greater aft loading that helps to reduce shock strength and transonic pressure drag. The cruise slotted wing may be considered a passive drag reduction technology with potential fuel-burn savings and increased vehicle range for next-generation aircraft. The current paper seeks to quantify the drag-saving benefits of cruise slotted wing technology in application to single-aisle commercial transport aircraft. A series of multielement design constraints were developed within CDISC for the design of a partial-span, cruise slotted wing for a Mach-0.8 variant of the Common Research Model. To mitigate the skin-friction drag penalty associated with cruise slotted wings, the design features a flap with natural laminar flow over approximately 75% of the flap surface area. Cruise drag estimates from the NASA USM3D-ME flow solver between a supercritical wing and the partial-span, cruise slotted wing design were within one drag count. Near-cruise, off-design analyses showed limited laminar-flow sensitivity to angle of attack and a more gradual drag rise compared to a supercritical wing. Based on this observed benefit, future work is motivated to design a cruise slotted wing with laminar flow on both wing elements to achieve a significant reduction in cruise drag while delaying drag divergence.

CDISC↗

Transonic Cruise Slotted Wing Design for Commercial Transport Aircraft using CDISC

A knowledge-based aerodynamic design method, CDISC, has been extended to enable the computational design of transonic cruise slotted wings for commercial transport aircraft. The cruise slotted wing is a multielement wing concept with a forward main element and an aft flap element, separated to form an intermediate slot. This slot favorably redirects airflow from the main element lower surface toward the low-momentum, upper-surface boundary layer of the flap. Relative to the supercritical wing, the cruise slotted wing enables greater aft loading that helps to reduce shock strength and transonic pressure drag. The cruise slotted wing may be considered a passive drag-reduction technology with potential fuel burn savings and increased vehicle range for next-generation aircraft. The current paper seeks to quantify the drag-saving benefits of cruise slotted wing technology in application to single-aisle commercial transport aircraft. A series of multielement design constraints were developed within CDISC for the design of a partial-span, cruise slotted wing for a Mach-0.8 variant of the Common Research Model. To mitigate the skin-friction drag penalty associated with cruise slotted wings, the design features a flap with natural laminar flow over approximately 75% of the flap surface area. Cruise drag estimates from the NASA USM3D flow solver between a supercritical wing and the partial-span, cruise slotted wing design were within one drag count. Near-cruise, off-design analyses showed limited laminar flow sensitivity to angle of attack and a more gradual drag rise compared to a supercritical wing. Based on this demonstrated benefit, future work is motivated to design a cruise slotted wing with natural laminar flow on both wing elements to achieve a significant reduction in cruise drag while providing delayed drag divergence.

CDISC↗

The use of a simplified structural model as an aid in the strain gage calibration of a complex wing

The use of a relatively simple structural model to characterize the load responses of strain gages located on various spars of a delta wing is examined. Strains measured during a laboratory load calibration of a wing structure are compared with calculations obtained from a simplified structural analysis model. Calculated and measured influence coefficient plots that show the shear, bending, and torsion characteristics of typical strain gage bridges are presented. Typical influence coefficient plots are shown for several load equations to illustrate the derivation of the equations from the component strain gage bridges. A relatively simple structural model was found to be effective in predicting the general nature of strain distributions and influence coefficient plots. The analytical processes are shown to be an aid in obtaining a good load calibration. The analytical processes cannot, however, be used in lieu of an actual load calibration of an aircraft wing.

Jenkins, J. M.↗

Accuracies of southwell and force/stiffness methods in the prediction of buckling strength of hypersonic aircraft wing tubular panels

Accuracies of the Southwell method and the force/stiffness (F/S) method are examined when the methods were used in the prediction of buckling loads of hypersonic aircraft wing tubular panels, based on nondestructive buckling test data. Various factors affecting the accuracies of the two methods were discussed. Effects of load cutoff point in the nondestructive buckling tests on the accuracies of the two methods were discussed in great detail. For the tubular panels under pure compression, the F/S method was found to give more accurate buckling load predictions than the Southwell method, which excessively overpredicts the buckling load. It was found that the Southwell method required a higher load cutoff point, as compared with the F/S method. In using the F/S method for predicting the buckling load of tubular panels under pure compression, the load cutoff point of approximately 50 percent of the critical load could give reasonably accurate predictions.

Ko, William L.↗

Effects of Body Shape on the Drag of a 45 degree Sweptback-Wing-Body Configuration at Mach Numbers from 0.90 to 1.43

An investigation was made of the effects of body shape on the drag of a 45 deg sweptback-wing-body combination at Mach numbers from 0.90 to 1.43. Both the expansion and compression fields induced by body indentation were swept back as the stream Mach number increased from 0.94. The line of zero pressure change was generally tangent to the Mach lines associated with the local velocities over the wing and body. The strength of the induced pressure fields over the wing were attenuated with spanwise distance and the major effects were limited to the inboard 60 percent of the wing semispan. Asymmetrical body indentation tended to increase the lift on the forward portion of the wing and reduce the lift on the rearward portion. This redistribution of lift had a favorable effect on the wave drag due to lift. Symmetrical body indentation reduced the drag loading near the wing-body juncture at all Mach numbers. The reduction in drag loading increased in spanwise extent as the Mach number increased and the line of zero induced pressure became more nearly aligned with the line of maximum wing thickness. Calculations of the wave drag due to thickness, the wave drag due to lift, and the vortex drag of the basic and symmetrical M = 1.2 body and wing combinations at an angle of attack of 0 deg predicted the effects of indentation within 11 percent of the wing-basic-body drag throughout the Mach number range from 1.0 to 1.43. Calculations of the wave drag due to thickness, the wave drag due to lift, and the vortex drag for the basic, symmetrical M = 1.2, and asymmetrical M = 1.4 body and wing combinations predicted the total pressure drag to within 8 percent of the experimental value at M = 1.43.

Olstad, Walter B.↗

Description of the HiMAT Tailored composite structure and laboratory measured vehicle shape under load

The aeroelastically tailored outer wing and canard of the highly maneuverable aircraft technology (HiMAT) vehicle are closely examined and a general description of the overall structure of the vehicle is provided. Test data in the form of laboratory measured twist under load and predicted twist from the HiMAT NASTRAN structural design program are compared. The results of this comparison indicate that the measured twist is generally less than the NASTRAN predicted twist. These discrepancies in twist predictions are attributed, at least in part, to the inability of current analytical composite materials programs to provide sufficiently accurate properties of matrix dominated laminates for input into structural programs such as NASTRAN.

Monaghan, R. C.↗