Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “WING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41
All sourcesNASA NTRSDOE OSTI
NASA NTRS2013

AMELIA CESTOL Test: Acoustic Characteristics of Circulation Control Wing with Leading- and Trailing-Edge Slot Blowing

The AMELIA Cruise-Efficient Short Take-off and Landing (CESTOL) configuration concept was developed to meet future requirements of reduced field length, noise, and fuel burn by researchers at Cal Poly, San Luis Obispo and Georgia Tech Research Institute under sponsorship by the NASA Fundamental Aeronautics Program (FAP), Subsonic Fixed Wing Project. The novel configuration includes leading- and trailing-edge circulation control wing (CCW), over-wing podded turbine propulsion simulation (TPS). Extensive aerodynamic measurements of forces, surfaces pressures, and wing surface skin friction measurements were recently measured over a wide range of test conditions in the Arnold Engineering Development Center(AEDC) National Full-Scale Aerodynamics Complex (NFAC) 40- by 80-Ft Wind Tunnel. Acoustic measurements of the model were also acquired for each configuration with 7 fixed microphones on a line under the left wing, and with a 48-element, 40-inch diameter phased microphone array under the right wing. This presentation will discuss acoustic characteristics of the CCW system for a variety of tunnel speeds (0 to 120 kts), model configurations (leading edge(LE) and/or trailing-edge(TE) slot blowing, and orientations (incidence and yaw) based on acoustic measurements acquired concurrently with the aerodynamic measurements. The flow coefficient, Cmu= mVSLOT/qSW varied from 0 to 0.88 at 40 kts, and from 0 to 0.15 at 120 kts. Here m is the slot mass flow rate, VSLOT is the slot exit velocity, q is dynamic pressure, and SW is wing surface area. Directivities at selected 1/3 octave bands will be compared with comparable measurements of a 2-D wing at GTRI, as will as microphone array near-field measurements of the right wing at maximum flow rate. The presentation will include discussion of acoustic sensor calibrations as well as characterization of the wind tunnel background noise environment.

Horne, William C.↗
NASA NTRS2015

Novel Control Effectors for Truss Braced Wing

At cruise flight conditions very high aspect ratio/low sweep truss braced wings (TBW) may be subject to design requirements that distinguish them from more highly swept cantilevered wings. High aspect ratio, short chord length and relative thinness of the airfoil sections all contribute to relatively low wing torsional stiffness. This may lead to aeroelastic issues such as aileron reversal and low flutter margins. In order to counteract these issues, high aspect ratio/low sweep wings may need to carry additional high speed control effectors to operate when outboard ailerons are in reversal and/or must carry additional structural weight to enhance torsional stiffness. The novel control effector evaluated in this study is a variable sweep raked wing tip with an aileron control surface. Forward sweep of the tip allows the aileron to align closely with the torsional axis of the wing and operate in a conventional fashion. Aft sweep of the tip creates a large moment arm from the aileron to the wing torsional axis greatly enhancing aileron reversal. The novelty comes from using this enhanced and controllable aileron reversal effect to provide roll control authority by acting as a servo tab and providing roll control through intentional twist of the wing. In this case the reduced torsional stiffness of the wing becomes an advantage to be exploited. The study results show that the novel control effector concept does provide roll control as described, but only for a restricted class of TBW aircraft configurations. For the configuration studied (long range, dual aisle, Mach 0.85 cruise) the novel control effector provides significant benefits including up to 12% reduction in fuel burn.

White, Edward V.↗
NASA NTRS2017

Computational Analysis of a Wing Designed for the X-57 Distributed Electric Propulsion Aircraft

A computational study of the wing for the distributed electric propulsion X-57 Maxwell airplane configuration at cruise and takeoff/landing conditions was completed. Two unstructured-mesh, Navier-Stokes computational fluid dynamics methods, FUN3D and USM3D, were used to predict the wing performance. The goal of the X-57 wing and distributed electric propulsion system design was to meet or exceed the required lift coefficient 3.95 for a stall speed of 58 knots, with a cruise speed of 150 knots at an altitude of 8,000 ft. The X-57 Maxwell airplane was designed with a small, high aspect ratio cruise wing that was designed for a high cruise lift coefficient (0.75) at angle of attack of 0deg. The cruise propulsors at the wingtip rotate counter to the wingtip vortex and reduce induced drag by 7.5 percent at an angle of attack of 0.6deg. The unblown maximum lift coefficient of the high-lift wing (with the 30deg flap setting) is 2.439. The stall speed goal performance metric was confirmed with a blown wing computed effective lift coefficient of 4.202. The lift augmentation from the high-lift, distributed electric propulsion system is 1.7. The predicted cruise wing drag coefficient of 0.02191 is 0.00076 above the drag allotted for the wing in the original estimate. However, the predicted drag overage for the wing would only use 10.1 percent of the original estimated drag margin, which is 0.00749.

Deere, Karen A.↗
NASA NTRS2015

Optimized Off-Design Performance of Flexible Wings with Continuous Trailing-Edge Flaps

This work assesses the potential aerodynamic performance benefits of a variable-camber, continuous-trailing-edge flap system on a generic transport aircraft at off-design conditions. A process to optimize transport wings while addressing static aeroelastic effects is presented. To establish a proper baseline, a transport wing is first aerodynamically optimized at a mid-cruise flight condition using an inviscid, aeroelastic analysis tool. The optimized wing is then analyzed at off-design cruise conditions. The optimization is repeated at these off-design conditions to determine how much performance is lost by the wing optimized solely for the mid-cruise condition. The full-span flap system is then adapted to improve performance of the mid-cruise-optimized wing at these off-design conditions. The measured improvement is quantified by a comparison with wings designed specifically for the off-design conditions. To evaluate the effects of aeroelasticity on the effectiveness of the flap system, this entire process is performed on both a conventionally stiff wing and a modern, more flexible wing. The results indicate that the flap system allows for recovery of near-optimal performance throughout cruise. The flap system is found to be advantageous even for modern wings with increased flexibility.

Rodriguez, David L.↗
NASA NTRS2014

Experimental Investigation of a Flexible Wing with a Variable Camber Continuous Trailing Edge Flap Design

This paper presents experimental results of a flexible wing wind tunnel model with a variable camber continuous trailing edge flap (VCCTEF) design for drag minimization, tested at the University of Washington Aeronautical Labo- ratory (UWAL). The wind tunnel test was designed to explore the relative merit of the VCCTEF concept for improved cruise efficiency through the use of low-cost aeroelastic model test techniques. The flexible wing model is a 10-scaled model of a typical transport wing and is constructed of woven fabric composites and foam core. The wing structural stiffness in bending is tailored to be half of the stiffness of a Boeing 757-era transport wing, while the torsional stiffness is about the same. This stiffness reduction results in a wing tip deflection of about 10 of the wing semi-span. The VCCTEF is a multi-segment flap design having three chordwise camber segments and five spanwise flap sections for a total of 15 individual flap elements. The three chordwise camber segments can be positioned appropriately to create a desired trailing edge camber. Elastomeric material is used to cover the gaps in between the spanwise flap sections, thereby creating a continuous trailing edge. Wind tunnel data indicate a high degree of data correlation and repeata- bility. The VCCTEF can achieve a drag reduction of up to 6.31 and an improvement in the lift-to-drag ratio (LD) of up to 4.85. The paper also presents two methods for estimating the lift coefficient of a rigid wing using a dynamic pressure correction and an aeroelastic deflection correction. Both methods provide good estimates of the rigid-wing lift coefficient.

Aerodynamics↗
NASA NTRS2015

Optimization for Load Alleviation of Truss-Braced Wing Aircraft with Variable Camber Continuous Trailing Edge Flap

This paper focuses on load alleviation optimization for a high aspect ratio truss braced wing (TBW) aircraft. The TBW aircraft model is based on the Subsonic Ultra Green Aircraft Research (SUGAR) concept developed by Boeing, with the wing structures of the model modified to include a novel aerodynamic control surface known as the Variable Camber Continuous Trailing Edge Flap (VCCTEF). The purpose of the study is to investigate the effectiveness of a Performance Adaptive Aeroelastic Wing (PAAW) technology, specifically the VCCTEF, for alleviating load on the TBW wing during flight maneuver. The specific flight maneuver under consideration in this study is a 2.5g pull-up maneuver. Constrained gradient-based optimization is conducted to tailor the deflections of the VC- CTEF such that bending moment along the wing is minimized at the 2.5g pull-up flight condition. Aerodynamic modeling for this study is conducted using a vortex-lattice method code called Vorlax. A non-linear finite element analysis (FEA) method is constructed for analyzing the structural deformation and resulting bending moment along the wing of the aircraft with the inclusion of effects from tension-stiffening due to axial loading in the truss. This study is the first phase of several, and involves optimization of a rigid wing aircraft for preliminary analysis. Future studies will incorporate flexible wing structures with aeroelastic interactions and deformations. The results of this first phase positively demonstrate the potential of utilizing the novel control surface on modern aircraft wing designs for shaping control in order to provide load alleviation during flight maneuver.

Lebofsky, Sonia↗
NASA NTRSDate not supplied

Effect of Geometric Fidelity on the Aerodynamics of a Swept Wing with Glaze Ice Accretion

Aerodynamic assessment of icing effects on swept wings is an important component of a larger effort to improve three-dimensional icing simulation capabilities. An understanding of ice-shape geometric fidelity on iced-wing aerodynamics and the associated flowfield features are needed to guide the development and validation of ice-accretion simulation tools. To this end, wind-tunnel testing was carried out for 8.9% and 13.3% scale semispan wing models based upon the Common Research Model airplane configuration. Various levels of geometric fidelity of an artificial ice shape representing a glaze-ice accretion on a swept wing were investigated. The highest fidelity artificial ice shape reproduced all of the three-dimensional features associated with the glaze ice accretion. The lowest fidelity artificial ice shapes were simple, spanwise-varying horn ice geometries intended to represent the maximum ice thickness on the wing upper surface. The results presented in this paper show that the addition of grit roughness to some lower-fidelity artificial ice shapes resulted in favorable lift and pitching moment comparisons to the wing with the highest fidelity artificial ice shape. In the range of 4.3 to 7.4 deg. angle of attack, surface oil flow visualization and pressure data show that the wing with the two lower fidelity simulations clearly demonstrated a leading edge vortex dominated flowfield, referred to as type I. For the wing with the high fidelity ice shape, the flowfield at lower angles of attack was characterized by streamwise-running, counter-rotating vortical flow referred to as type II. Between 6.4 and 7.4 deg. angle of attack, the effect of the type II flow structures was significantly altered and gave way to the type I leading edge vortex. This means that for angles of attack 7.4 deg. and higher, the wing with all three configurations exhibited the same type of flowfield. This helps to explain why there is reasonably good agreement in the lift and pitching moment coefficients among these configurations.

Aircraft icing↗
NASA NTRS2021

Pretest Computational Assessment of Boundary Layer Transition in the NASA Juncture Flow Model with an NACA 0015-Based Wing

The first two phases of the NASA Juncture Flow experiment were carried out on a DLR-F6 swept-wing model and were designed to provide “CFD validation-quality” data toward the assessment and improvement of existing CFD turbulence models in predicting onset and extent of three-dimensional separated flow near the wing-juncture trailing-edge region. The next phase of experiments will involve an NACA 0015-based swept wing, as prior risk reduction experiments had indicated that this wing shape resulted in reduced separation near the juncture region than the DLR-F6 wing, thus providing a better option to evaluate the ability of CFD models to predict incipient turbulent separation. The NACA 0015 measurements will also include IR thermography to infer the variation of transition front with respect to an increasing angle of attack. The primary objective of this work is to computationally make a preliminary assessment of the transition front on both surfaces of the NACA 0015 wing at a crank-chord-based Reynolds number of 2.4 x 106 for four different angles of attack, (0°, 2.5°, 5°, and 7.5°) and to determine the dominant mechanisms responsible for transition. This assessment includes both RANS-based transition models from NASA’s OVERFLOW 2.3b flow solver and linear parabolized stability equations (PSE) stability analysis based on the Langley Stability and Transition Analysis code, LASTRAC. Linear PSE results indicate that the upper surface of the wing is dominated by Tollmien- Schlichting (TS) instabilities, and that the laminar flow region shrinks from about 50% chord to a very small region just downstream of the attachment line as the angle of attack is increased from 0° to 7.5°. Consequently, the transition fronts predicted by the Spalart- Allmaras-based amplification factor transport (AFT-2017b) equation model (which accounts for the TS instabilities alone) and the Menter’s shear-stress transport equation (SST2003)- based Langtry-Menter transition model with ability to account for both TS and crossflow effects (LM2015) compare well with those predicted using linear PSE. On the lower surface of the wing, stationary crossflow (CF) instabilities begin to appear on the inboard portion of the wing in addition to the TS-instabilities for the larger angles of attack (5° and 7.5°), further reducing the laminar flow extent within the inboard region. The LM2015 model that accounts for CF effects is able to replicate this trend but appears to predict a slightly earlier transition. The outcome of this effort will inform the experiment and, when the actual experimental data become available, provide further opportunity to assess and improve the various transition models.

CFD modeling↗
NASA NTRS2021

Pretest Computational Assessment of Boundary Layer Transition in the NASA Juncture Flow Model with an NACA 0015-Based Wing

The first two phases of the NASA Juncture Flow experiment were carried out on a DLR-F6 swept-wing model and were designed to provide “CFD validation-quality” data toward the assessment and improvement of existing CFD turbulence models in predicting onset and extent of three-dimensional separated flow near the wing-juncture trailing-edge region. The next phase of experiments will involve an NACA 0015-based swept wing, as prior risk reduction experiments had indicated that this wing shape resulted in reduced separation near the juncture region than the DLR-F6 wing, thus providing a better option to evaluate the ability of CFD models to predict incipient turbulent separation. The NACA 0015 measurements will also include IR thermography to infer the variation of transition front with respect to an increasing angle of attack. The primary objective of this work is to computationally make a preliminary assessment of the transition front on both surfaces of the NACA 0015 wing at a crank-chord-based Reynolds number of 2.4 x 106 for four different angles of attack, (0°, 2.5°, 5°, and 7.5°) and to determine the dominant mechanisms responsible for transition. This assessment includes both RANS-based transition models from NASA’s OVERFLOW 2.3b flow solver and linear parabolized stability equations (PSE) stability analysis based on the Langley Stability and Transition Analysis code, LASTRAC. Linear PSE results indicate that the upper surface of the wing is dominated by Tollmien- Schlichting (TS) instabilities, and that the laminar flow region shrinks from about 50% chord to a very small region just downstream of the attachment line as the angle of attack is increased from 0° to 7.5°. Consequently, the transition fronts predicted by the Spalart- Allmaras-based amplification factor transport (AFT-2017b) equation model (which accounts for the TS instabilities alone) and the Menter’s shear-stress transport equation (SST2003)- based Langtry-Menter transition model with ability to account for both TS and crossflow effects (LM2015) compare well with those predicted using linear PSE. On the lower surface of the wing, stationary crossflow (CF) instabilities begin to appear on the inboard portion of the wing in addition to the TS-instabilities for the larger angles of attack (5° and 7.5°), further reducing the laminar flow extent within the inboard region. The LM2015 model that accounts for CF effects is able to replicate this trend but appears to predict a slightly earlier transition. The outcome of this effort will inform the experiment and, when the actual experimental data become available, provide further opportunity to assess and improve the various transition models.

CFD modeling↗
NASA NTRS1944

The Effects of a Highly Cambered Low-Drag Wing and of Auxiliary Flaps on the High-Speed Aerodynamic Characteristics of a Twin-Engine Pursuit Airplane Model

Results are presented for tests of two wings, an NACA 230-series wing and a highly-cambered NACA 66-series wing on a twin-engine pursuit airplane. Auxiliary control flaps were tested in combinations with each wing. Data showing comparison of high-speed aerodynamic characteristics of the model when equipped with each wing, the effect of the auxiliary control flaps on aerodynamic characteristics, and elevator effectiveness for the model with the 66-series wing are presented. High-speed aerodynamic characteristics of the model were improved with the 66-series wing.

AIRFOILS - NACA 66,2-416-66,2-616 - CHAR & MOMENTS↗
NASA NTRS1933

The Effects of Slots and Flaps on Lateral Control of a Low-wing Monoplane as Determined in Flight

This paper presents the results of flight tests made to determine the effect of slots and flaps on the lateral control of a low-wing monoplane. Maximum angular accelerations in roll and yaw produced by sudden application of the ailerons and maximum accelerations in yaw produced by sudden application of the rudder during gliding flight were recorded for the following wing arrangements: (a) no auxiliary device; (b) full-span slots; (c) plain flaps; (d) flaps and full-span slots; (e) wing-tip slots. Rolling- and yawing-moment coefficients were derived from the accelerations. The full span slots and the flaps each had about the same influence on the aileron rolling moments. At values of the lift coefficient obtainable with the plain wing, the effect of these devices was negligible. At the higher lift coefficients obtainable with these devices, the rolling-moment coefficients increased slightly but, despite this increase, the aileron effectiveness progressively decreased with increasing lift coefficient, owing to the corresponding reduction in air speed. In the range covered by the tests, the effectiveness of the controls was appreciably reduced by the wing-tip slots. The adverse yawing moment of the ailerons experienced at the large lift coefficients obtained with the flaps was appreciably less than at similar lift coefficients obtained with either full-span or wing-tip slots. The yawing moments produced by the rudder were only slightly affected by the use of the auxiliary devices. The airplane was found to be laterally unstable with all combinations tested. Because of the angular velocities acquired in the time taken to deflect the ailerons the rolling moments recorded in flight were only about two thirds the values that would have been obtained with the wing restrained as in wind-tunnel tests.

WING SLOTS↗
NASA NTRS1951

Investigation of the Effects of Twist and Camber on the Aerodynamic Characteristics of a 50 Degrees 38 Minutes Sweptback Wing of Aspect Ratio 2.98 : Transonic-bump Method

An investigation of two semispan wings swept back 50 degrees 38 minutes was conducted in the Langley high-speed 7- by 10-foot tunnel over a Mach number range of 0.68 to 1.15 by use of the transonic-bump technique. This paper presents the results of the investigation of wing-alone and wing-fuselage configurations of the two wings; one was an untwisted uncambered wing and the other was the same wing but incorporated twist and camber designed to give uniform load at a lift coefficient of 0.25 at a Mach number of 1.10. The semispan wings had their quarter-chord lines swept back 50 degrees 38 minutes, aspect ratios 2.98, taper ratios 0.45, and modified NACA 64A-series airfoil sections tapered in thickness. Lift, pitching moment, drag, and bending moment were obtained for these configurations.

WINGS, COMPLETE - DESIGN VARIABLES↗
DOE OSTI2020

Physical and behavioral adaptations to prevent overheating of the living wings of butterflies

The wings of Lepidoptera contain a matrix of living cells whose function requires appropriate temperatures. However, given their small thermal capacity, wings can overheat rapidly in the sun. Here we analyze butterfly wings across a wide range of simulated environmental conditions, and find that regions containing living cells are maintained at cooler temperatures. Diverse scale nanostructures and non-uniform cuticle thicknesses create a heterogeneous distribution of radiative cooling that selectively reduces the temperature of structures such as wing veins and androconial organs. These tissues are supplied by circulatory, neural and tracheal systems throughout the adult lifetime, indicating that the insect wing is a dynamic, living structure. Behavioral assays show that butterflies use wings to sense visible and infrared radiation, responding with specialized behaviors to prevent overheating of their wings. Our work highlights the physiological importance of wing temperature and how it is exquisitely regulated by structural and behavioral adaptations.

59 BASIC BIOLOGICAL SCIENCES↗
NASA NTRS1972

Wing optimization for space shuttle orbiter vehicles

The results were presented of a parametric study performed to determine the optimum wing geometry for a proposed space shuttle orbiter. The results of the study establish the minimum weight wing for a series of wing-fuselage combinations subject to constraints on aerodynamic heating, wing trailing edge sweep, and wing over-hang. The study consists of a generalized design evaluation which has the flexibility of arbitrarily varying those wing parameters which influence the vehicle system design and its performance. The study is structured to allow inputs of aerodynamic, weight, aerothermal, structural and material data in a general form so that the influence of these parameters on the design optimization process can be isolated and identified. This procedure displays the sensitivity of the system design of variations in wing geometry. The parameters of interest are varied in a prescribed fashion on a selected fuselage and the effect on the total vehicle weight is determined. The primary variables investigated are: wing loading, aspect ratio, leading edge sweep, thickness ratio, and taper ratio.

Surber, T. E.↗
NASA NTRS1974

Effects of air breathing engine plumes on SSV orbiter subsonic wing pressure distribution, volume 2

Data presented were obtained during wind tunnel tests of a 0.0405-scale model of the -89B ferry configuration of the space shuttle vehicle orbiter. These tests were conducted in the Rockwell International low speed wind tunnel (NAAL). The primary test objective was to investigate orbiter wing pressure distributions resulting from nacelle plumes above and below the wing. Three six-engine nacelle configurations were tested. One configuration has a twin-podded nacelle mounted above each wing and the others had one mounted below each wing. Both had a centerline twin-podded nacelle mounted below the wing. Wing pressure distribution was determined by locating static pressure bugs on the upper and lower surfaces of the left wing. Pressure bugs were also located on the upper and lower surfaces of the body flap and on the B12 afterbody fairing when it was installed. Base and balance cavity pressures were recorded and a strain gage instrumented beam in the right wing measured elevon hinge moments and normal forces.

Soard, T.↗
NASA NTRS1974

Effects of air breathing engine plumes on SSV orbiter subsonic wing pressure distribution (OA57B), volume 1

Data were obtained during wind tunnel tests of a 0.0405-scale model of the ferry configuration of the space shuttle vehicle orbiter conducted in a low speed wind tunnel during the time period of September 18 to September 23, 1973. The primary test objective was to investigate orbiter wing pressure distributions resulting from nacelle plumes above and below the wing. Three six-engine nacelle configurations were tested. One configuration had a twin-podded nacelle mounted above each wing and the others had one mounted below each wing. Both had a centerline twin-podded nacelle mounted below the wing. Wing pressure distribution was determined by locating static pressure bugs on the upper and lower surfaces of the left wing. Pressure bugs were also located on the upper and lower surfaces of the body flap and on the B12 afterbody fairing when it was installed. Base and balance cavity pressures were recorded and a strain gage instrumented beam in the right wing measured elevon hinge moments and normal forces.

Soard, T.↗
NASA NTRS1976

Effect of drooped-nose flaps on the experimental force and moment characteristics of an oblique wing

Six-component experimental force and moment data are presented for a low aspect ratio, oblique wing equipped with drooped-nose flaps and mounted on top of a body of revolution. These flaps were investigated on the downstream wing panel with the nose drooped 5 deg, 10 deg, 20 deg, and 30 deg, and on both wing panels with the nose drooped 30 deg. It was to determine if such flaps would make the moment curves more linear by controlling the flow separation on the downstream wing panel at high lift coefficients. The wing was elliptical in planform and had an aspect ratio of 6.0 (based on the unswept wing span). The wing was tested at sweep angles of 45 deg and 50 deg throughout the Mach number range from 0.25 to 0.95. The drooped-nose flaps alone were not effective in making the moment curves more linear; however, a previous study showed that Kruger nose flaps improved the linearity of the moment curves when the Kruger flaps were used on only the downstream wing panel equipped with drooped-nose flaps deflected 5 deg.

Hopkins, E. J.↗
NASA NTRS1977

Aileron and Krueger nose flap effectiveness measured on an oblique wing

The effects that deflection of conventional ailerons have on the lateral/directional characteristics of an oblique wing mounted on top of a body of revolution were measured. The wing had an aspect ratio of 6 (based on the unswept wing span) and was tested at various sweep angles ranging from 0 deg to 60 deg. Krueger nose flaps mounted on drooped-nose flaps were investigated on the downstream wing panel (for sweep angles of 45 deg and 60 deg) in an attempt to create more symmetrical spanwise wing stalling at high lift coefficients. The tests were conducted over a Mach number range of 0.25 to 1.4 and an angle-of-attack range from -3 deg to 28 deg. With the oblique wing in the swept position, considerable difference in the aileron effectiveness was measured for positive or negative differential aileron deflections. With the wing swept 45 deg at a Mach number of 0.8 and above, an extension of the span of the Krueger nose flaps on the downstream wing panel did not improve the linearity of the pitching-, rolling-, and yawing-moment curves.

Hopkins, E. J.↗