Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “VORTEX”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

On the onset of three-dimensionality and time-dependence in the Goertler vortex problem

The instability of large amplitude Goertler vortices in a growing boundary layer is discussed in the fully nonlinear regime. It is shown that a three-dimensional breakdown to a flow with wavy vortex boundaries similar to that which occurs in the Taylor vortex problem takes place. However, the instability is confined to the thin shear layers which have been shown to trap the region of vortex activity. The disturbance eigenfunctions decay exponentially away from the center of these layers so that the upper and lower shear layers can support independent modes of instability. The structure of the instability, in particular its location and speed of downstream propagation, is found to be entirely consistent with recent experimental results. Furthermore, it is shown that the upper and lower layers support wavy vortex instabilities with quite different frequencies. This result is again consistent with the available experimental observations.

Hall, Philip↗

Viscous vortex flows

Several computational studies are currently being pursued that focus on various aspects of representing the entire lifetime of the viscous trailing vortex wakes generated by an aircraft. The formulation and subsequent near-wing development of the leading-edge vortices formed by a delta wing are being calculated at modest Reynolds numbers using a three-dimensional, time-dependent Navier-Stokes code. Another computational code was developed to focus on the roll-up, trajectory, and mutual interaction of trailing vortices further downstream from the wing using a two-dimensional, time-dependent, Navier-Stokes algorithm. To investigate the effect of a cross-wind ground shear flow on the drift and decay of the far-field trailing vortices, a code was developed that employs Euler equations along with matched asymptotic solutions for the decaying vortex filaments. And finally, to simulate the conditions far down stream after the onset of the Crow instability in the vortex wake, a full three-dimensional, time-dependent Navier-Stokes code was developed to study the behavior of interacting vortex rings.

Weston, R. P.↗

Roles of initial condition and vortex pairing in jet noise

Sound generation by vortex pairing in circular and elliptic cold-air jets at Mach 0.15-0.35 is investigated experimentally, with a focus on the effects of initial conditions. The results are presented in graphs and interpreted using the theory of vortex sound proposed by Moehring (1978) and vortex-filament models of jet coherent structure. Tripping the nozzle boundary layer is shown to (1) preempt formation of shear-layer vortices, (2) remove the sound they produce in later pairing, and (3) increase the diffusion of coherent vorticity in the vortex rings. Hence pairing noise should not be significant in practical jets, which are initially turbulent.

Bridges, J. E.↗

Navier-Stokes simulations of axisymmetric vortex rings

The solution of the incompressible Navier-Stokes equations by means of a spectral method is used in the present numerical investigation of viscous axisymmetric vortex rings, in the cases of a single ring over the 0.001-1000 Re number range, and a pair of interacting rings. The propagation speeds of vortex rings of varying Re are computed and compared with the results of Saffman's (1970) theory; the present error estimate is found to be smaller than Saffman's, and to decrease with increasing Re at fixed core/ring radius ratio. The 'leapfrogging' of two vortex rings of equal sign and Re=1000 each is observed, indicating severe strain of the vortex core through the first pass and merging during the second pass.

Stanaway, S. K.↗

Propagation of vortex rings and starting plumes in high and low g

The propagation of vortex rings and starting plumes during crystal growth in supercooled solutions was investigated in variable gravity environment created by acceleration-deceleration routine of a NASA's KC-135 flight. A specially designed crystal growth cell was used to study convection around crystals growing in supersaturated solutions of Na2SO4 and NaCl aboard the NASA KC-135. The results of vertical velocity measurements have shown that a continuously fed plume attains a higher velocity than the individual vortex ring. The results also indicated that the vortex ring decelerates as it propagates, and slows down much more rapidly than the starting plume, indicating a less efficient transport. It is suggested that inertial effects and buoyancy effects on vortex and plume propagation can be separated in the controlled environment of a Space Station borne centrifuge.

Hallett, J.↗

Interaction and merging of vortex filaments

The asymptotic solutions of Navier-Stokes equations for vortex filaments of finite strength with small effective vortical cores are summarized with special emphasis placed on the physical meaning and the practical limit to the applicability of the asymptotic solution. Finite-difference solutions of Navier-Stokes equations for the marging of the filament(s) are described with a focus on the development of the approximate boundary conditions for the computational domain. An efficiency study employing a model problem is used to assess the advantages of the present approximate boundary condition method over previously used techniques. Applications of the present method are presented for the motion and decay of a 3:1 elliptic vortex ring, and for the merging process of a pair of coaxial vortex rings. A numerical procedure for the problem of local merging of vortex filaments, which requires the asymptotic analysis as well as the numerical Navier-Stokes solver, is also presented.

Liu, C. H.↗

Three-dimensional mean flow experimental study of 'vortex unwinding'

A seven-hole flow-angularity pressure probe was used to assess the effectiveness of vortex unwinding in a turbulent boundary layer. The vortex center moved in the spanwise and vertical direction with increasing longitudinal distance. Initially, the vortex moved rapidly; it achieved 60 percent of its total 41 mm spanwise travel before it had completed half of its travel in the longitudinal direction. The flow was studied behind the single vortex combined with the most successful unwinder. The unwinder was found to be very effective in reducing the amount of secondary flow in the boundary layer.

Mcginley, Catherine B.↗

An experimental investigation of the ground vortex created by a moving jet

A 1 inch circular jet moving over a fixed ground board was studied in the NASA Langley Research Center Vortex Research Center. The jet passing over the ground board at a height of three nozzle diameters creates a ground vortex which was measured by a pattern of Endevco high response pressure transducers. The results are compared to existing data to determine the effect of the ground boundary eliminated by the moving jet. The penetration of the vortex both forward of and latterly to the impact point of the jet on the ground. The resulting ground vortex penetration forward of the impact point is reduced by approximately 30 percent and the lateral penetration is reduced by 50 percent over that experienced from a stationary jet over a stationary ground board with a free stream velocity.

Stewart, V. R.↗

Measurements of a supersonic turbulent vortex

Mean-flow measurements of a supersonic turbulent streamwise vortex are presented. This vortex was produced by the injection of a swirling flow along the centerline of a supersonic airstream at Mach 3. Directional Mach number distributions, obtained via a five-hole flow-angularity probe, reveal vortex characteristics similar to those of the incompressible case, even though rotational Mach numbers up to 0.8 were obtained. This work is the first step of a study of the supersonic vortex breakdown phenomenon.

Metwally, O. M.↗

Cross-linking of two antiparallel vortex tubes

The detailed mechanisms in vortex cross-linking are unveiled by adequately resolved, direct numerical simulation of two viscous vortex tubes. There are three characteristic phases: (1) inviscid induction followed by core flattening and stretching; (2) bridging of the two vortices by accumulation of annihilated and then cross-linked vortex lines; and (3) threading of the remnants of the initial vortex pair in between the two bridges as they pull apart. These phases and the role of threading (along with bridging) in the mixing and the enstrophy cascade are explained, and it is shown that the mechanism is insensitive to asymmetries.

Melander, M. V.↗

Interaction of an oscillating vortex with a turbulent boundary layer

An oscillating vortex embedded within a turbulent boundary layer was generated experimentally by forcing a periodic lateral translation of a half-delta wing vortex generator. The objective of the experiment was to investigate the possibility that a natural oscillation, or meander, might be responsible for flattened vortex cores observed in previous work, which could also have contaminated previous turbulence measurements. The effect of this forced oscillation was characterized by comparison of measurements of the mean velocities and Reynolds stresses at two streamwise stations, for cases with and without forcing. The Reynolds stresses were affected significantly by the forced oscillation, mainly through contributions from the individual production terms, provided that the vortex was not too diffuse.

Westphal, R. V.↗

Zero-Gravity Vortex Vent and PVT Gaging System

Space Station and satellite reservicing will require the ability to vent gas on orbit from liquid supply or storage tanks and to gage liquid quantity under microgravity conditions. In zero gravity, (zero-g) the vortex vent is capable of venting gas from a tank of liquid containing gas randomly distributed as bubbles. The concept uses a spinning impeller to create centrifugal force inside a vortex tube within a tank. This creates a gas pocket and forces the liquid through a venturi and back into the tank. Gas is then vented from the gas pocket through a liquid detector and then out through an exhaust port. If the liquid detector senses liquid in the vent line, the fluid is directed to the low-pressure port on the venturi and is returned to the tank. The advantages of this system is that it has no rotating seals and is compatible with most corrosive and cryogenic fluids. A prototype was designed and built at the NASA Johnson Space Center and flown on the KC-135 zero-g aircraft. During these test flights, where microgravity conditions are obtained for up to 30 sec, the prototype demonstrated that less than 0.10 percent of the volume of fluid vented was liquid when the tank was half full of liquid. The pressure volume temperature (PVT) gaging system is used in conjunction with the vortex vent to calculate the amount of liquid remaining in a tank under microgravity conditions. The PVT gaging system is used in conjunction with the vortex vent to gage liquid quantity in zero or low gravity. The system consists of a gas compressor, accumulator, and temperature and pressure instrumentation. To measure the liquid in a tank a small amount of gas is vented from the tank to the compressor and compressed into the accumulator. Pressure and temperature in the tank and accumulator are measured before and after the gas transfer occurs. Knowing the total volume of the tank, the volume of the accumulator, the volume of the intermediate lines, and initial and final pressures and temperatures, the mass of the gas leaving the tank is equated to the mass of the gas entering the accumulator. The volume of liquid remaining in the tank is calculated using the ideal gas law.

Downey, M. G.↗

Dynamics of a class of vortex rings

The contour dynamics method is extended to vortex rings with vorticity varying linearly from the symmetry axis. An elliptic core model is also developed to explain some of the basic physics. Passage and collisions of two identical rings are studied focusing on core deformation, sound generation and stirring of fluid elements. With respect to core deformation, not only the strain rate but how rapidly it varies is important and accounts for greater susceptibility to vortex tearing than in two dimensions. For slow strain, as a passage interaction is completed and the strain relaxes, the cores return to their original shape while permanent deformations remain for rapidly varying strain. For collisions, if the strain changes slowly the core shapes migrate through a known family of two-dimensional steady vortex pairs up to the limiting member of the family. Thereafter energy conservation does not allow the cores to maintain a constant shape. For rapidly varying strain, core deformation is severe and a head-tail structure in good agreement with experiments is formed. With respect to sound generation, good agreement with the measured acoustic signal for colliding rings is obtained and a feature previously thought to be due to viscous effects is shown to be an effect of inviscid core deformation alone. For passage interactions, a component of high frequency is present. Evidence for the importance of this noise source in jet noise spectra is provided. Finally, processes of fluid engulfment and rejection for an unsteady vortex ring are studied using the stable and unstable manifolds. The unstable manifold shows excellent agreement with flow visualization experiments for leapfrogging rings suggesting that it may be a good tool for numerical flow visualization in other time periodic flows.

Shariff, Karim↗

Ground evaluation of seeding an in-flight wingtip vortex using infrared imaging flow visualization technique

An experimental simulation of an in-flight wingtip vortical flow visualization technique uses infrared imaging to observe strong and concentrated vortices. This experiment is phase 1 of a two-phase infrared evaluation program. The system includes a vortex generator (model 320 Vortec Vortex Tube) which generates the required vortex. The mouth of the unit is mounted close to the free end of a half-inch diameter, sixteen and a half foot long stainless steel tubing (sized after tubing currently installed in the wings of an experimental Beechcraft Sundowner 180 aircraft). Dichloro difluoromethane (Freon-12) is entrained into the generated vortex. A breakdown of the vortices is indicated by the rapid diffusion and the resulting pattern is tracked using the infrared imager and video systems. Flow rates (volume and mass) are estimated at the laboratory and proposed flight conditions. The nominal flight altitude is expected to be 2500 feet.

Akinyanju, Ted↗

Tip vortex geometry of a hovering helicopter rotor in ground effect

The wide-field shadowgraph method has been used to photograph the tip vortices of a hovering helicopter rotor in ground effect. The shadowgraphs were used to obtain quantitative measurements of the rotor tip vortex geometry both in and out of ground effect. Many important phenomena are visible in the rotor wake using this method. These include the variation in descent and contraction rates of the tip vortices in ground effect, and the interaction between tip vortices in the far wake. The tip vortex geometry from the shadowgraphs is compared with the tip vortex geometry predicted using a free wake hover performance analysis. The free wake analysis accurately predicts the tip vortex geometry both in and out of ground effect. Performance data from the test is compared with the performance predicted using several methods, including the free wake analysis. All methods provided reasonable predictions for the helicopter performance in ground effect.

Light, Jeffrey S.↗

N2O as a dynamical tracer in the Arctic vortex

This paper reports N2O measurements obtained by the Airborne Tunable Laser Absorption Spectrometer from 14 flights of the NASA ER-2 aircraft during the 1989 Airborne Arctic Stratospheric Expedition field campaign. In the altitude range expected for ozone loss, N2O has a long photochemical lifetime, making it an excellent tracer of lower stratospheric air motions. As in the southern hemisphere, the zonal wind speed maximum and large gradients of potential vorticity and N2O identify the vortex edge. The N2O profiles inside the vortex indicate net descent relative to outside the vortex and to the summer polar lower stratosphere. The descent of the N2O profile during the Arctic night relative to the summer profile is comparable to the downward shift in the vertical profile observed in the 1987 Antarctic winter vortex. Winter profiles at the poles are very similar above the 435 K potential temperature surface, but divergent below.

Loewenstein, M.↗

Euler solutions for self-generated rotor blade-vortex interactions

A finite-difference procedure was developed, on the basis of the conservation form of the unsteady three-dimensional Euler equations, for the prediction of rotor blade-vortex interactions (BVIs). Numerical solution procedures were obtained for the analysis of the model parallel BVIs and the more realistic helicopter self-generated-rotor BVIs. It was found that, for self-generated subcritical interactions, the accuracy of the predicted leading edge pressures relied heavily on the user-specified vortex core radius and on the CAMRAD-code-predicted geometry of the interaction vortex elements and their relative orientation with respect to the blade. It was also found that the free-wake model used in CAMRAD to predict the tip vortex trajectory for use in the Euler solution yields lower streamwise and higher axial wake convective velocities than those inferred from the experimental data.

Hassan, A. A.↗

A numerical study of longitudinal vortex interaction with a boundary layer

A numerical study of vortex generator aerodynamics has been carried out with a reduced set of Navier-Stokes equations. These are used to model the physical process of longitudinal vortex interaction with a turbulent boundary layer on a flat plate in incompressible flow. Comparison with experimental data is used to validate the approach, and detailed predictions are made. Results show an increase in skin friction and a decrease in integral layer thicknesses where the flow is toward the wall, and the reverse where the flow is away from the wall. The major controlling parameters of vortex strength, spacing and height are each found to have optimum values for which the efficiency of boundary-layer thinning is maximized. Vortex core spreading and secondary vorticity produced in the layer are observed and studied, as well as circulation decay and other features of the flow.

Russell, D. A.↗