Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Thrust”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

Thrust stand evaluation of engine performance improvement algorithms in an F-15 airplane

Results are presented from the evaluation of the performance seeking control (PSC) optimization algorithm developed by Smith et al. (1990) for F-15 aircraft, which optimizes the quasi-steady-state performance of an F100 derivative turbofan engine for several modes of operation. The PSC algorithm uses onboard software engine model that calculates thrust, stall margin, and other unmeasured variables for use in the optimization. Comparisons are presented between the load cell measurements, PSC onboard model thrust calculations, and posttest state variable model computations. Actual performance improvements using the PSC algorithm are presented for its various modes. The results of using PSC algorithm are compared with similar test case results using the HIDEC algorithm.

Conners, Timothy R.↗

Examination of various turbulence models for application in liquid rocket thrust chambers

There is a large variety of turbulence models available. These models include direct numerical simulation, large eddy simulation, Reynolds stress/flux model, zero equation model, one equation model, two equation k-epsilon model, multiple-scale model, etc. Each turbulence model contains different physical assumptions and requirements. The natures of turbulence are randomness, irregularity, diffusivity and dissipation. The capabilities of the turbulence models, including physical strength, weakness, limitations, as well as numerical and computational considerations, are reviewed. Recommendations are made for the potential application of a turbulence model in thrust chamber and performance prediction programs. The full Reynolds stress model is recommended. In a workshop, specifically called for the assessment of turbulence models for applications in liquid rocket thrust chambers, most of the experts present were also in favor of the recommendation of the Reynolds stress model.

Hung, R. J.↗

Low thrust chemical rocket technology

An on-going technology program to improve the performance of low thrust chemical rockets for spacecraft on-board propulsion applications is reviewed. Improved performance and lifetime is sought by the development of new predictive tools to understand the combustion and flow physics, introduction of high temperature materials and improved component designs to optimize performance, and use of higher performance propellants. Improved predictive technology is sought through the comparison of both local and global predictions with experimental data. Predictions are based on both the RPLUS Navier-Stokes code with finite rate kinetics and the JANNAF methodology. Data were obtained with laser-based diagnostics along with global performance measurements. Results indicate that the modeling of the injector and the combustion process needs improvement in these codes and flow visualization with a technique such as 2-D laser induced fluorescence (LIF) would aid in resolving issues of flow symmetry and shear layer combustion processes. High temperature material fabrication processes are under development and small rockets are being designed, fabricated, and tested using these new materials. Rhenium coated with iridium for oxidation protection was produced by the Chemical Vapor Deposition (CVD) process and enabled an 800 K increase in rocket operating temperature. Performance gains with this material in rockets using Earth storable propellants (nitrogen tetroxide and monomethylhydrazine or hydrazine) were obtained through component redesign to eliminate fuel film cooling and its associated combustion inefficiency while managing head end thermal soakback. Material interdiffusion and oxidation characteristics indicated that the requisite lifetimes of tens of hours were available for thruster applications. Rockets were designed, fabricated, and tested with thrusts of 22, 62, 440 and 550 N. Performance improvements of 10 to 20 seconds specific impulse were demonstrated. Higher performance propellants were evaluated: Space storable propellants, including liquid oxygen (LOX) as the oxidizer with nitrogen hydrides or hydrocarbon as fuels. Specifically, a LOX/hydrazine engine was designed, fabricated, and shown to have a 95 pct theoretical c-star which translates into a projected vacuum specific impulse of 345 seconds at an area ratio of 204:1. Further performance improvment can be obtained by the use of LOX/hydrogen propellants, especially for manned spacecraft applications, and specific designs must be developed and advanced through flight qualification.

Schneider, Steven J.↗

Numerical simulation of STOL operations using thrust-vectoring

The flow field about a delta wing equipped with thrust reverser jets in slow speed flight near the ground has been computed. Results include the prediction of the flow about the delta wing at four fixed heights above the ground, and a simulated landing, in which the delta wing descends towards the ground. Comparison of computed and experimental lift coefficients indicates that the simulations can capture at least the qualitative trends in lift-loss encountered by thrust-vectoring aircraft operating in ground effect.

Chawla, Kalpana↗

Design and fabrication of a hydrogen/oxygen thrust chamber assembly

The combustion system for the Advance Expander Test Bed engine consists of a thrust mount, an injector with a H2-O2 torch igniter, a combustion chamber, and a conical nozzle extension. These components constitute the thrust chamber assembly. The design, fabrication, and testing of these components are described in detail.

Hernacki, Thomas R.↗

Fluidic scale model multi-plane thrust vector control test results

An experimental investigation has been conducted at the NASA Langley 16-Foot Transonic Tunnel Static Test Facility to determine the concept feasibility of using fluidics to achieve multiplane thrust vector control in a 2D convergent-divergent (2D-CD) fixed aperture nozzle. Pitch thrust vector control is achieved by injection of flow through a slot in the divergent flap into the primary nozzle flow stream. Yaw vector control results from secondary air delivered tangentially to vertical Coanda flaps. These flaps are offset laterally and aligned parallel to the primary nozzle side walls. All tests were conducted at static (no external flow) conditions. Flow visualization was conducted using a paint flow technique and Focus Schlieren. Significant levels of pitch deflection angles (19 deg) were achieved at low pressure ratios and practical levels (14 deg) resulted at typical intermediate power settings. The ability of the Coanda surface blowing concept to produce yaw deflection was limited to NPR not greater than 4.

Chiarelli, Charles↗

Computation of optimal low- and medium-thrust orbit transfers

This paper presents the formulation of the optimal low- and medium-thrust orbit transfer control problem, numerical methods for solution, and numerical solutions of the problem. The problem formulation is for final mass maximization and allows for second-harmonic oblateness, atmospheric drag, and 3D noncoplanar nonaligned elliptic terminal orbits. We set up examples to demonstrate the ability of two indirect methods to solve the resulting two point boundary value problems (TPBVP). The methods demonstrated are the multiple point shooting method as formulated in Oberle's (1987) subroutine BOUNDSCO, and the minimizing boundary-condition method (MBCM). We find that although both methods can converge solutions, there are tradeoffs to using either method. We present numerical solutions of planar transfers in which both the initial orbit exit and final orbit entry points have been optimized. These solutions include two- and three-burn transfers. The methods used show an ability to handle thrust down to at least T/W(o) = O(10 exp -3). They also show similar convergence abilities with or without the oblateness and drag terms. We discuss the issue of maximizing with respect to the final time and provide evidence that implies a local optimum at a maximum final time for a given number of burns.

Chuang, C.-H.↗

Deep space communications technology thrusts

The paper discusses the technology thrusts that are currently being developed for deep space missions as well as the expected dividends of these thrusts during the 1990's and beyond. Particular attention is given to Ka-band (32 GHz) development, channel coding, source coding, and optical communications. The ongoing development described here attempts to meet the telecommunications demands of future missions by stressing cooperative developments between ground networks and flight projects in order to optimize NASA's overall investment in solar system investment.

Yuen, Joseph H.↗

Static Thrust Analysis of the Lifting Airscrew

This report presents the results of a combined theoretical and experimental investigation conducted at the Georgia School of Technology on the static thrust of the lifting air screw of the type used in modern autogiros and helicopters. The theoretical part of this study is based on Glauert's analysis but certain modifications are made that further clarify and simplify the problem. Of these changes the elimination of the solidity as an independent parameter is the most important. The experimental data were obtained from tests on four rotor models of two, four, and five blades and, in general, agree quite well with the theoretical calculations. The theory indicates a method of evaluating scale effects on lifting air screws, and these corrections have been applied to the model results to derive general full-scale static thrust, torque, and figure-of-merit curves for constant-chord, constant-incidence rotors. Convenient charts are included that enable hovering flight performance to be calculated rapidly.

Knight, Montgomery↗

Performance of 4600-pound-thrust centrifugal-flow-type turbojet engine with water-alcohol injection at inlet

An experimental investigation of the effects of injecting a water-alcohol mixture of 2:1 at the compressor inlet of a centrifugal-flow type turbojet engine was conducted in an altitude test chamber at static sea-level conditions and at an altitude of 20,000 feet with a flight Mach number of 0.78 with an engine operating at rated speed. The net thrust was augmented by 0.16 for both flight conditions with a ratio of injected liquid to air flow of 0.05. Further increases in the liquid-air ratio did not give comparable increases in thrust.

Glasser, Philip W↗

Investigation of Thrust and Drag Characteristics of a Plug-type Exhaust Nozzle

An investigation was conducted in the 8- by 6-foot supersonic wind tunnel on the external and internal characteristics of a plug-type exhaust nozzle. Two positions of the center plug, one simulating a convergent nozzle and the other a convergent-divergent nozzle, were investigated. Data were obtained at free-stream Mach numbers of 0.1, 0.6, 1.6, and 2.0 over a pressure-ratio range of 1 to 20 and angles of attack of zero and 8 degrees. Results of this investigation indicated that the plug nozzle had thrust-minus-drag performance over the entire pressure-ratio range comparable with equivalent conventional nozzles. The effect of the exhaust jet on the external aerodynamics was similar to results observed for conventional nozzles. In addition, the thrust characteristics were generally insensitive to external flow and good agreement was noted with data obtained on comparable plug nozzles in quiescent air.

Hearth, Donald P↗

Static thrust of airplane propellers

Static thrust data from more than 100 airplane propeller tests are collected from various sources and combined in working charts, from which the static thrust coefficient may be readily determined. The available data cover practically all types of propellers and are in good agreement.

Diehl, Walter S↗

An analytical and experimental study of the effect of periodic blade twist on the thrust, torque, and flapping motion of an autogiro rotor

An analysis is made of the influence on autogiro rotor characteristics of a periodic blade twist that varies with the azimuth position of the rotor blade and the results are compared with experimental data. The analysis expresses the influence of this type of twist upon the thrust, torque, and flapping motion of the rotor. The check against experimental data shows that the periodic twist has a pronounced influence on the flapping motion and that this influence is accurately predicted by the analysis. The influence of the twist upon the thrust and torque could be demonstrated only indirectly, but its importance is indicated.

Wheatley, John B↗

Effect of Target-type Thrust Reverser on Transonic Aerodynamic Characteristics of a Single-engine Fighter Model

A brief investigation of a target-type thrust reverser on a single-engine fighter model has been conducted in the Langley 16-foot transonic tunnel at Mach numbers from 0.20 to 1.05.At Mach numbers of 0.80, 0.92, and 1.05, a hydrogen peroxide turbojet-engine simulator was operated with the thrust reverser extended. The angle of attack was varied from 0 degrees to 5 degrees at these Mach numbers. The Reynolds number of the free stream, based on the mean aerodynamic chord, was about 5 x 10(6). It was estimated that reversed jet operations separated the model boundary-layer flow over the upper surface of the horizontal tail and upper part of the afterbody. This resulted in a positive pitch increment due to reversed jet operation. Jet-on operation also tended to stabilize the severe lateral oscillations which occurred with the reverser extended and the jet off. It appeared that these jet-off oscillations were the result of an alternating separation and reattachment of the flow on the rearmost portions of the fuselage afterbody.

Swihert, John M↗

Dynamic Imbalance Would Counter Offcenter Thrust

Dynamic imbalance generated by offcenter thrust on rotating body eliminated by shifting some of mass of body to generate opposing dynamic imbalance. Technique proposed originally for spacecraft including massive crew module connected via long, lightweight intermediate structure to massive engine module, such that artificial gravitation in crew module generated by rotating spacecraft around axis parallel to thrust generated by engine. Also applicable to dynamic balancing of rotating terrestrial equipment to which offcenter forces applied.

Mccanna, Jason↗

Moving-base simulation evaluation of thrust margins for vertical landing for the NASA YAV-8B Harrier aircraft

A simulation experiment was conducted on Ames Research Center's Vertical Motion Simulator to evaluate the thrust margin for vertical landing required for the YAV-8B Harrier. Two different levels of ground effect were employed, representing the aircraft with or without lift improvement devices installed. In addition, two different inlet temperature profiles were included to cover a wide range of hot gas ingestion. For each ground effect and hot gas ingestion variant, vertical landings were performed at successively heavier weights, with the pilot assessing the acceptability of the operation in each case. Results are presented as a function of hover weight ratio and a metric of the mean ground effect and ingestion that reflect the increase in thrust margin required to provide acceptable control of sink rate during the descent to touchdown with increasing suck down and hot gas ingestion.

Franklin, James A.↗

Design and evaluation of single and dual flow thrust vector nozzles with post exit vanes

This Thrust Vectored Research project required that a 1/24 scale model of the F/A-18 High Alpha Research Vehicle, (HARV), propulsion system be constructed on the university campus. This propulsion system was designed for cold flow testing on a multicomponent test rig. Forces and moments were measured to study nozzle performance parameters. The flow visualization technique of color Schlieren photography was performed to investigate the flow phenomena at the nozzle exit. The flow interactions that were identified consisted of vane nozzleing between the outer and lower vanes and vane tip interference. The thrust vectoring system consisted of three asymmetrically spaced vanes installed circumferentially on a maximum afterburner nozzle. The performance of the nozzle was investigated with the outer and lower vanes equally deflected, (-10 deg is less than delta(sub v) is less than 25 deg), and with the upper vane fully retracted, (delta(sub v) equals -10 deg). The nozzle pressure ratio ranged from 4 to 6. The results indicated that a vane nozzleing effect developed at nozzle pressure ratios of 4 and 6 when the outer and lower vanes were deflected far enough into the flow field such that the increase in vane area accelerated the flow past the vanes causing distorted shock waves. This accelerated flow was a result of a pressure differential existing between the inside surface of the vane and the ambient pressure. The stagnation pressure that developed along the inside surface of the vane accelerated the flow past the vanes causing it to equalize with ambient pressure, thus providing distorted shock waves. A tip interference was present at the trailing edge of the upper vane as a result of low nozzle pressure, NPR 4, with high vane deflection, delta(sub v) equals 25 degrees, and also with a high nozzle pressure, NPR 6, and low vane deflections, delta(sub v) equals 15 degrees.

Carpenter, Thomas W.↗