Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Thermal Modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

Gas Generation Models for Thermal Runaway in Lithium Ion Batteries

A numerical model is implemented to study cell venting, internal pressure, and gas-phase dynamics behavior of Li-ion cells undergoing thermal runaway. A k-ɛ Reynolds-Averaged Navier-Stokes (RANS) model is adopted to describe the turbulent flow out of the cells, while the fluid dynamics inside the cells is described by Darcy-Forchheimer’s equation. Thermal abuse reactions and gas generation kinetics are described by a single-step lumped reaction model. A series of computational fluid dynamics (CFD) simulations are conducted on a single cell at various states-of-charge (100%, 50%, 25%) to demonstrate detailed flow and thermal behavior as a function of quantity of gas generated during cell venting. Venting events are categorized into two stages: i) breaching of the cell container and ii) thermal runaway reactions. It is shown that the cell response is dominated by the second stage since most of the gases are generated during thermal runaway. Also, the propensity for propagation is highly affected by state-of-charge (SOC). Cells at higher SOCs produce more heat and gas during the venting event, owing to higher mass and concentrations of reacting gases, and consequently reach higher internal cell pressures which increase the risk of side-wall breaching.

Kim, Jinyong↗

The solar simulation test of the ITALSAT thermal structural model

The ITALSAT structural/thermal model (STM) was submitted to a solar simulation test in order to verify the spacecraft thermal design and the thermal mathematical model which will be used to predict the on orbit temperatures. The STM was representative of the flight model in terms of configuration, structures, appendages and thermal hardware; dissipating dummy units were used to simulate the electronic units. The test consisted of the main phases: on station (beginning of life), on station (end of life), and transfer orbit. Preliminary results indicate that the test performances were satisfactory. The spacecraft measured temperatures were up to 15 degrees higher than the predicted ones. This imposes a careful correlation analysis in order to have reliable flight temperature predictions.

Giommi, M.↗

A Flow Rate Dependent 1D Model for Thermally Stratified Hot-Water Energy Storage

Stratified tank models are used to simulate thermal storage in applications such as residential or commercial hot-water storage tanks, chilled-water storage tanks, and solar thermal systems. The energy efficiency of these applications relates to the system components and the level of stratification maintained during various flow events in the tank. One-dimensional (1D) models are used in building energy simulations because of the short computation time but often do not include flow-rate dependent mixing. The accuracy of 1D models for plug flow, plug flow with axial conduction, and two convection eddy-diffusivity models were compared with experimental data sets for discharging a 50-gal residential tank and recharging the tank with hot water from an external hot-water source. A minimum and maximum relationship for the eddy diffusivity factor were found at Re <2100 and >10,000 for recirculation of hot water to the top of the tank and vertical tubes inletting cold water at the bottom. The root mean square error decreased from >4 °C to near 2 °C when considering flow-based mixing models during heating, while the exponential decay of the eddy diffusion results in a root mean square error reduction of 1 °C for cone-shaped diffusers that begin to relaminarize flow at the inlet.

1D flow model↗

Parametric Thermal Soak Model for Earth Entry Vehicles

The analysis and design of an Earth Entry Vehicle (EEV) is multidisciplinary in nature, requiring the application many disciplines. An integrated tool called Multi Mission System Analysis for Planetary Entry Descent and Landing or M-SAPE is being developed as part of Entry Vehicle Technology project under In-Space Technology program. Integration of a multidisciplinary problem is a challenging task. Automation of the execution process and data transfer among disciplines can be accomplished to provide significant benefits. Thermal soak analysis and temperature predictions of various interior components of entry vehicle, including the impact foam and payload container are part of the solution that M-SAPE will offer to spacecraft designers. The present paper focuses on the thermal soak analysis of an entry vehicle design based on the Mars Sample Return entry vehicle geometry and discusses a technical approach to develop parametric models for thermal soak analysis that will be integrated into M-SAPE. One of the main objectives is to be able to identify the important parameters and to develop correlation coefficients so that, for a given trajectory, can estimate the peak payload temperature based on relevant trajectory parameters and vehicle geometry. The models are being developed for two primary thermal protection (TPS) materials: 1) carbon phenolic that was used for Galileo and Pioneer Venus probes and, 2) Phenolic Impregnated Carbon Ablator (PICA), TPS material for Mars Science Lab mission. Several representative trajectories were selected from a very large trade space to include in the thermal analysis in order to develop an effective parametric thermal soak model. The selected trajectories covered a wide range of heatload and heatflux combinations. Non-linear, fully transient, thermal finite element simulations were performed for the selected trajectories to generate the temperature histories at the interior of the vehicle. Figure 1 shows the finite element model that was used for the simulations. The results indicate that it takes several hours for the thermal energy to soak into the interior of the vehicle and achieve maximum payload temperatures. In addition, a strong correlation between the heatload and peak payload container temperature is observed that will help establishing the parametric thermal soak model.

Agrawal, Parul↗

Thermal-mechanical modeling of nodular defect embedded within multilayer coatings

The initiation of laser damage within optical coatings can be better understood by thermal-mechanical modeling of coating defects. The result of this modeling shows that a high-temperature rise and thermal stress can be seen just inside the nodular defect compared to surrounding coating layers. The temperature rise and thermal stress tend to increase with seed diameter. Shallower seed tend to cause higher temperature rise and greater thermal stress. There is a critical seed depth at which thermal stress is largest. The composition of the seed resulting from different coating-material emission during evaporation can affect the temperature rise and thermal stress distribution.

36 MATERIALS SCIENCE↗

DEVELOPMENT OF BURN TEST SPECIFICATIONS FOR FIRE PROTECTION MATERIALS IN RAM PACKAGES

The regulations in 10 CFR 71 require that the radioactive material (RAM) packages must be able to withstand specific fire conditions given in 10 CFR 71.73 during Hypothetical Accident Conditions (HAC). This requirement is normally satisfied by extensive testing of full scale test specimens under required test conditions. Since fire test planning and execution is expensive and only provides a single snapshot into a package performance, every effort is made to minimize testing and supplement tests with results from computational thermal models. However, the accuracy of such thermal models depends heavily on the thermal properties of the fire insulating materials that are rarely available at the regulatory fire temperatures. To the best of authors knowledge no test standards exist that could be used to test the insulating materials and derive their thermal properties for the RAM package design. This paper presents a review of the existing industry fire testing standards and proposes testing methods that could serve as a standardized specification for testing fire insulating materials for use in RAM packages.

42 ENGINEERING↗

Coupled Reactor and Engine Nuclear Thermal Propulsion Modeling Methodology

The design and development process of a Nuclear Thermal Propulsion (NTP) system requires extensive multiphysics modeling to couple the neutron physics and thermal feedback effects to determine the reactor’s power shape. Propulsion system performance codes utilize this power shape to determine NTP key performance parameters. While the power shape is heavily dependent on the temperature profile and geometry of the reactor, many analyses either assume a constant power shape, or use neutronics analysis to determine a power shape for a specific reactor configuration. The development of a coupling interface for a propulsion system performance code and a Monte Carlo neutron transport code (OpenMC) allows for the reactor power shape to be calculated in an iteration loop. The interface utilizes a file share system to transfer geometry dimensions, temperatures, and material identifiers to OpenMC, which is used to perform a neutron transport simulation of a design like the government Testing Reference Design reactor. The interface is then able to post-process the results from OpenMC and use the same file share system to share a power shape and other important neutron transport parameters to the system performance code. Initial results show that neglecting the changes to power shape when comparing reactor configurations can yield inaccurate results. Furthermore, utilizing propellants other than hydrogen gas can cause significant changes to the power shape, and thus, the thermal performance of a specific reactor design. This methodology is being expanded to allow for multiple families of NTP reactors to be analyzed, including block moderator, particle bed, and NERVA-derived reactors.

multiphysics coupling↗

Coupled Reactor and Engine Nuclear Thermal Propulsion Modeling Methodology

The design and development process of a Nuclear Thermal Propulsion (NTP) system requires extensive multiphysics modeling to couple the neutron physics and thermal feedback effects to determine the reactor’s power shape. Propulsion system performance codes utilize this power shape to determine NTP key performance parameters. While the power shape is heavily dependent on the temperature profile and geometry of the reactor, many analyses either assume a constant power shape, or use neutronics analysis to determine a power shape for a specific reactor configuration. The development of a coupling interface for a propulsion system performance code and a Monte Carlo neutron transport code (OpenMC) allows for the reactor power shape to be calculated in an iteration loop. The interface utilizes a file share system to transfer geometry dimensions, temperatures, and material identifiers to OpenMC, which is used to perform a neutron transport simulation of a design like the government Testing Reference Design reactor. The interface is then able to post-process the results from OpenMC and use the same file share system to share a power shape and other important neutron transport parameters to the system performance code. Initial results show that neglecting the changes to power shape when comparing reactor configurations can yield inaccurate results. Furthermore, utilizing propellants other than hydrogen gas can cause significant changes to the power shape, and thus, the thermal performance of a specific reactor design. This methodology is being expanded to allow for multiple families of NTP reactors to be analyzed, including block moderator, particle bed, and NERVA-derived reactors.

multiphysics coupling↗

Thermal Integration of a Liquid Acquisition Device into a Cryogenic Feed System

Primary objectives of this effort were to define the following: (1) Approaches for quantification of the accumulation of thermal energy within a capillary screen liquid acquisition device (LAD) for a lunar lander upper stage during periods of up to 210 days on the lunar surface, (2) techniques for mitigating heat entrapment, and (3) perform initial testing, data evaluation. The technical effort was divided into the following categories: (1) Detailed thermal modeling of the LAD/feed system interactions using both COMSOL computational fluid device and standard codes, (2) FLOW-3D modeling of bulk liquid to provide interfacing conditions for the LAD thermal modeling, (3) condensation conditioning of capillary screens to stabilize surface tension retention capability, and (4) subscale testing of an integrated LAD/feed system. Substantial progress was achieved in the following technical areas: (1) Thermal modeling and experimental approaches for evaluating integrated cryogen LAD/feed systems, at both the system and component levels, (2) reduced gravity pressure control analyses, (3) analytical modeling and testing for capillary screen conditioning using condensation and wicking, and (4) development of rapid turnaround testing techniques for evaluating LAD/feed system thermal and fluid integration. A comprehensive effort, participants included a diverse cross section of representatives from academia, contractors, and multiple Marshall Space Flight Center organizations.

Hastings, L. J.↗

Verification and transfer of thermal pollution model. Volume 3: Verification of 3-dimensional rigid-lid model

The six-volume report: describes the theory of a three dimensional (3-D) mathematical thermal discharge model and a related one dimensional (1-D) model, includes model verification at two sites, and provides a separate user's manual for each model. The 3-D model has two forms: free surface and rigid lid. The former, verified at Anclote Anchorage (FL), allows a free air/water interface and is suited for significant surface wave heights compared to mean water depth; e.g., estuaries and coastal regions. The latter, verified at Lake Keowee (SC), is suited for small surface wave heights compared to depth (e.g., natural or man-made inland lakes) because surface elevation has been removed as a parameter. These models allow computation of time-dependent velocity and temperature fields for given initial conditions and time-varying boundary conditions. The free-surface model also provides surface height variations with time.

Lee, S. S.↗

Verification and transfer of thermal pollution model. Volume 5: Verification of 2-dimensional numerical model

The six-volume report: describes the theory of a three dimensional (3-D) mathematical thermal discharge model and a related one dimensional (1-D) model, includes model verification at two sites, and provides a separate user's manual for each model. The 3-D model has two forms: free surface and rigid lid. The former, verified at Anclote Anchorate (FL), allows a free air/water interface and is suited for significant surface wave heights compared to mean water depth; e.g., estuaries and coastal regions. The latter, verified at Lake Keowee (SC), is suited for small surface wave heights compared to depth (e.g., natural or man-made inland lakes) because surface elevation has been removed as a parameter. These models allow computation of time dependent velocity and temperature fields for given initial conditions and time-varying boundary conditions.

Lee, S. S.↗

Verification and transfer of thermal pollution model. Volume 6: User's manual for 1-dimensional numerical model

The six-volume report: describes the theory of a three dimensional (3-D) mathematical thermal discharge model and a related one dimensional (1-D) model, includes model verification at two sites, and provides a separate user's manual for each model. The 3-D model has two forms: free surface and rigid lid. The former, verified at Anclote Anchorage (FL), allows a free air/water interface and is suited for significant surface wave heights compared to mean water depth; e.g., estuaries and coastal regions. The latter, verified at Lake Keowee (SC), is suited for small surface wave heights compared to depth (e.g., natural or man-made inland lakes) because surface elevation has been removed as a parameter.

Lee, S. S.↗

Coupled Reactor and Engine Nuclear Thermal Propulsion Modeling Methodology

The design and development process of a Nuclear Thermal Propulsion (NTP) system requires extensive multiphysics modeling to couple the neutron physics and thermal feedback effects to determine the reactor’s power shape. Propulsion system performance codes utilize this power shape to determine NTP key performance parameters. While the power shape is heavily dependent on the temperature profile and geometry of the reactor, many analyses either assume a constant power shape, or use neutronics analysis to determine a power shape for a specific reactor configuration. The development of a coupling interface for a propulsion system performance code and a Monte Carlo neutron transport code (OpenMC) allows for the reactor power shape to be calculated in a Picard iteration.

Jacob Stonehill↗

Multi-Node Thermal System Model for Lithium-Ion Battery Packs: Preprint

Temperature is one of the main factors that controls the degradation in lithium ion batteries. Accurate knowledge and control of cell temperatures in a pack helps the battery management system (BMS) to maximize cell utilization and ensure pack safety and service life. In a pack with arrays of cells, a cells temperature is not only affected by its own thermal characteristics but also by its neighbors, the cooling system and pack configuration, which increase the noise level and the complexity of cell temperatures prediction. This work proposes to model lithium ion packs thermal behavior using a multi-node thermal network model, which predicts the cell temperatures by zones. The model was parametrized and validated using commercial lithium-ion battery packs. neighbors, the cooling system and pack configuration, which increase the noise level and the complexity of cell temperatures prediction. This work proposes to model lithium ion packs thermal behavior using a multi-node thermal network model, which predicts the cell temperatures by zones. The model was parametrized and validated using commercial lithium-ion battery packs.

25 ENERGY STORAGE↗

Comparison between Flownex and Corona thermal-hydraulic models for a single HTR prismatic fuel assembly - 18544

Computational tools and methodologies that can perform thermal-hydraulic analyses to reasonably predict the temperature distribution for the whole core of HTRs are useful for operational and safety analyses. In this paper, Flownex (a system code based on a one-dimensional thermal-fluid network methodology) and CORONA (Core Reliable Optimization and thermo-fluid Network Analysis) thermal-hydraulic models and results for a vertically stacked single fuel assembly will be compared. In Flownex, a basic unit cell containing part of the graphite and the associated fuel elements and coolant channels was developed. CORONA uses a basic unit cell concept for generating computational grids using several types of basic unit cells to model the heat transfer through the hexagonal blocks and a 1-D formulation to model the flow through the coolant channels. In CORONA, computational grids are generated using a combination of pre-generated mesh cells. The coolant channels and fuel rods are modelled explicitly. Flownex in contrast, models fuel and coolant channels implicitly by defining representative coolant channels, fuel rods and coated particle layers associated with each unit cell. Flownex can therefore model temperatures at coated particle level and also through each graphite block. The computational mesh employed by Flownex is much coarser than the mesh employed by CORONA. In both models, the helium gap between the fuel compact and the graphite block is modelled as stagnant. Flownex results were found to be of the same order of magnitude as those obtained using CORONA. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Verification and transfer of thermal pollution model. Volume 2: User's manual for 3-dimensional free-surface model

The six-volume report: describes the theory of a three-dimensional (3-D) mathematical thermal discharge model and a related one-dimensional (1-D) model, includes model verification at two sites, and provides a separate user's manual for each model. The 3-D model has two forms: free surface and rigid lid. The former, verified at Anclote Anchorage (FL), allows a free air/water interface and is suited for significant surface wave heights compared to mean water depth; e.g., estuaries and coastal regions. The latter, verified at Lake Keowee (SC), is suited for small surface wave heights compared to depth. These models allow computation of time-dependent velocity and temperature fields for given initial conditions and time-varying boundary conditions.

Lee, S. S.↗

Thermal 𝑅⁢𝐶 circuit model for resolving the thermal paradox

Thermal measurements of heat capacity and thermal conductivity in a wide range of insulators and superconductors exhibit a “thermal paradox”: a large linear specific heat reminiscent of neutral Fermi surfaces (associated with fractionalized quasiparticles) in nonmetallic samples that exhibit no corresponding linear temperature coefficient to the thermal conductivity. At first sight, these observations appear to support the formation of a continuum of thermally localized many-body excitations, a form of many-body localization that would be fascinating in its own right. Here, in this work, by mapping thermal conductivity measurements onto thermal 𝑅⁢𝐶 circuits, we argue that the development of extremely long thermal relaxation times, a “thermal bottleneck,” is likely in systems with either many-body localization or neutral Fermi surfaces due to the large ratio between the electron and phonon specific heat capacities. We present a reevaluation of thermal conductivity measurements in materials exhibiting a thermal paradox that can be used in future experiments to deliberate between these two exciting alternatives.

heat transfer↗