Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TUNNEL EFFECT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Elastic deformation effects on aerodynamic characteristics for a high-aspect-ratio supercritical-wing model

The results of an investigation of the deformations of a high-aspect-ratio, force/pressure, supercritical-wing model during wind tunnel tests and the effects these deformations have on the wing aerodynamics are presented. A finite element model of the wing was developed, and then, for conditions corresponding to wind tunnel test points, experimental aerodynamic loads and theoretical aerodynamic loads were applied to the finite element model. Comparisons were made between the results of these load conditions for changes in structural deflections and for changes in aerodynamic characteristics. The results show that the deformations are quite small and that the pressure data are not significantly affected by model deformation.

Watson, J. J.↗
NASA NTRS1970

Effects of Nose Bluntness on Aerodynamic Characteristics of Cruciform-Finned Missile Configuration at Mach 1.50 to 2.86

An investigation has been conducted in the Langley Unitary Plan wind tunnel to determine the effects of spherical nose bluntness on the aerodynamic characteristics of a typical cruciform-finned short-range missile configuration for roll angles of 0 deg and 45 deg and Mach numbers from 1.50 to 2.86. Also investigated was the effectiveness of a forward protruding nose spike in reducing the axial-force coefficient of a blunt-nose configuration. The results indicated that the effects of nose bluntness and nose spike on the longitudinal stability were small. For roll angles of both 0 deg and 45 deg, the greatest effects of nose bluntness on the aerodynamic-center location near zero angle of attack occurred at a Mach number of 2.86, where for each roll position, a rearward shift of approximately 3.5 percent of the body length occurred as bluntness was increased. Although large magnitudes of nose bluntness were accompanied by high axial-force coefficients, significant reductions in the axial-force coefficient of a blunt-nose configuration were achieved with the use of the nose spike. There were no noteworthy effects of nose bluntness on either the directional stability or side-force parameters. However, for high angles of attack at a Mach number of 1.50 increased nose bluntness generally resulted in decreased effective dihedral.

Jernell, L. S.↗
NASA NTRS1985

Effects of empennage surface location on aerodynamic characteristics of a twin-engine afterbody model with nonaxisymmetric nozzles

An investigation has been conducted in the Langley 16-Foot Transonic Tunnel to determine the effects of empennage surface location and vertical tail cant angle on the aft-end aerodynamic characteristics of a twin-engine fighter-type configuration. The configuration featured two-dimensional convergent-divergent nozzles and twin-vertical tails. The investigation was conducted with different empennage locations that included two horizontal and three vertical tail positions. Vertical tail cant angle was varied from -10 deg to 20 deg for one selected configuration. Tests were conducted at Mach number 0.60 to 1.20 and at angles of attack -3 to 9 deg. Nozzle pressure ratio was varied from jet off to approximately 9, depending upon Mach number. Tail interference effects were present throughout the range of Mach numbers tested and found to be either favorable or adverse, depending upon test condition and model configuration. At a Mach number of 0.90, adverse interference effects accounted for a significant percentage of total aft-end drag. Interference effects on the nozzle were generally favorable but became adverse as the horizontal tails were moved from a mid to an aft position. The configuration with nonaxisymmetric nozzles had lower total aft-end drag with tails-off than a similar configuration with axisymmetric nozzles at Mach numbers of 0.60 and 0.90.

Capone, Francis J.↗
NASA NTRS1990

Effect of tail size reductions on longitudinal aerodynamic characteristics of a three surface F-15 model with nonaxisymmetric nozzles

An investigation was conducted in the Langley 16-Foot Transonic Tunnel to determine the effects of horizontal and vertical tail size reductions on the longitudinal aerodynamic characteristics of a modified F-15 model with canards and 2-D convergent-divergent nozzles. Quantifying the drag decrease at low angles of attack produced by tail size reductions was the primary focus. The model was tested at Mach numbers of 0.40, 0.90, and 1.20 over an angle of attack of -2 degree to 10 degree. The nozzle exhaust flow was simulated using high pressure air at nozzle pressure ratios varying from 1.0 (jet off) to 7.5. Data were obtained on the baseline configuration with and without tails as well as with reduced horizontal and/or vertical tail sizes that were 75, 50, and 25 percent of the baseline tail areas.

Frassinelli, Mark C.↗
NASA NTRS1979

Two dimensional aerodynamic interference effects on oscillating airfoils with flaps in ventilated subsonic wind tunnels

The numerical computation of unsteady airloads acting upon thin airfoils with multiple leading and trailing-edge controls in two-dimensional ventilated subsonic wind tunnels is studied. The foundation of the computational method is strengthened with a new and more powerful mathematical existence and convergence theory for solving Cauchy singular integral equations of the first kind, and the method of convergence acceleration by extrapolation to the limit is introduced to analyze airfoils with flaps. New results are presented for steady and unsteady flow, including the effect of acoustic resonance between ventilated wind-tunnel walls and airfoils with oscillating flaps. The computer program TWODI is available for general use and a complete set of instructions is provided.

Fromme, J.↗
NASA NTRS1985

Effect of aileron deflections on the aerodynamic characteristics of a semispan model of a subsonic energy-efficient transport

An investigation was conducted in the Langley 8 Foot Transonic Pressure Tunnel to determine the effect of aileron deflections on the aerodynamic characteristics of a subsonic energy efficient transport (EET) model. The semispan model had an aspect ratio 10 supercritical wing and was configured with a conventionally located set of ailerons (i.e., a high speed aileron located inboard and a low speed aileron located outboard). Data for the model were taken over a Mach number range from 0.30 to 0.90 and an angle of attack range from approximately -2 deg to 10 deg. The Reynolds number was 2.5 million per foot for Mach number = 0.30 and 4 million per foot for the other Mach numbers. Model force and moment data, aileron effectiveness parameters, aileron hinge moment data, otherwise pressure distributions, and spanwise load data are presented.

Jacobs, P. F.↗
NASA NTRS1938

The Effect of Surface Irregularities on Wing Drag. I. Rivets and Spot Welds: Rivets and Spot Welds - 1

Tests have been conducted in the NACA 8-foot high-speed wind tunnel to determine the effect of exposed rivet heads and spot welds on wing drag. Most of the tests were made with an airfoil of 5-foot chord. The air speed was varied from 80 to 500 miles per hour and the lift coefficient from 0 to 0.30. The increases in the drag of the 5-foot airfoil varied from 6%, due to countersunk rivets, to 27%, due to 3/32-inch brazier-head rivets, with the rivets in a representative arrangement. The drag increases caused by protruding rivet heads were roughly proportional to the height of the heads. With the front row of rivets well forward, changes in spanwise pitch had negligible effects on drag unless the pitch was more than 2.5% of the chord. Data are presented for evaluating the drag reduction attained by removing rivets from the forward part of the wing surface; for example, it is shown that over 70% of the rivet drag is caused by the rivets on the forward 30% of the airfoil in a typical case.

Hood, Manley J.↗
NASA NTRS1974

Effects of Reynolds number and model support on the supersonic aerodynamic chacteristics of a 140 deg-included-angle cone

An investigation has been made in the Langley Unitary Plan wind tunnel to determine the effects of Reynolds number and sting-support interference on the static aerodynamic characteristics of a 140 deg-included-angle cone. Base pressures and forces and moments of the model were measured at Mach numbers of 1.50, 2.00, 2.94, and 4.00 for ratios of sting diameter to model diameter that varied from 0.125 to 0.500 through an angle-of-attack range from about minus 4 deg to 13 deg. The Reynolds number, based on model diameter 4.80 in. was varied from 161,000 to 415,000.

Trescot, C. D., Jr.↗
NASA NTRS1933

Effect of stabilizer location upon pitching and yawing moments in spins as shown by tests with the spinning balance

Tests were made with the spinning balance in a 5-foot wind tunnel to study the effect of stabilizer location upon the pitching and yawing moments given by the tail surfaces in spinning attitudes. The tests revealed that the horizontal surfaces, when in a normal location, seriously reduced the effectiveness of the fin and rudder, particularly at angles of attack of 50 degrees or more. The tests also revealed that a more forward or more rearward location gave no consistent or decided improvement; that a lower location greatly increased the shielding so that the yawing moment from the combination was in general less than that given by the bare fuselage; and that a higher location decreased the shielding and gave a favorable interference effect, particularly at the high angles of attack. Additional results regarding the stabilizer and the elevator are given.

Bamber, M J↗
NASA NTRS1948

Effects of a sweptback hydrofoil on the force and longitudinal stability characteristics of a typical high-speed airplane

An investigation was conducted in the Langley 8-foot high-speed tunnel to determine the effects of a sweptback hydrofoil on the force and longitudinal stability characteristics of a typical high-speed airplane. The Mach number range for this investigation was from 0.60 to 0.95 and at M = 1.20. The effects of the hydrofoil on the lift, drag, and pitching-moment characteristics are presented.

AIRPLANES - COMPONENTS IN COMBINATION↗
NASA NTRS1953

The Effects on Dynamic Lateral Stability and Control of Large Artificial Variations in the Rotary Stability Derivatives

This report presents the results of an investigation conducted in the Langley free-flight tunnel to determine the effects of large artificial variations of several rotary lateral-stability derivatives on the dynamic lateral stability and control characteristics of a 45 degree sweptback-wing airplane model. Calculations of the period and damping of the lateral motions and of the response to roll and yaw disturbances were made for correlation with the experimental results. The calculated results were in qualitative agreement with the experimental results in predicting the general trends in flight characteristics produced by large changes in the stability derivatives, but in some cases the theory with the assumption of zero lag was not in good quantitative agreement with the experimental results.

Schade, Robert O↗
NASA NTRS1960

Effects of Sweep Angle on the Boundary-Layer Stability Characteristics of an Untapered Wing at Low Speeds

An investigation was conducted in the Ames 12-Foot Low-Turbulence Pressure Tunnel to determine the effects of sweep on the boundary-layer stability characteristics of an untapered variable-sweep wing having an NACA 64(2)A015 section normal to the leading edge. Pressure distribution and transition were measured on the wing at low speeds at sweep angles of 0, 10, 20, 30, 40, and 50 deg. and at angles of attack from -3 to 3 deg. The investigation also included flow-visualization studies on the surface at sweep angles from 0 to 50 deg. and total pressure surveys in the boundary layer at a sweep angle of 30 deg. for angles of attack from -12 to 0 deg. It was found that sweep caused premature transition on the wing under certain conditions. This effect resulted from the formation of vortices in the boundary layer when a critical combination of sweep angle, pressure gradient, and stream Reynolds number was attained. A useful parameter in indicating the combined effect of these flow variables on vortex formation and on beginning transition is the crossflow Reynolds number. The critical values of crossflow Reynolds number for vortex formation found in this investigation range from about 135 to 190 and are in good agreement with those reported in previous investigations. The values of crossflow Reynolds number for beginning transitions were found to be between 190 and 260. For each condition (i.e., development of vortices and initiation of transition at a given location) the lower values in the specified ranges were obtained with a light coating of flow-visualization material on the surface. A method is presented for the rapid computation of crossflow Reynolds number on any swept surface for which the pressure distribution is known. From calculations based on this method, it was found that the maximum values of crossflow Reynolds number are attained under conditions of a strong pressure gradient and at a sweep angle of about 50 deg. Due to the primary dependence on pressure gradient, effects of sweep in causing premature transition are generally first encountered on the lower surfaces of wings operating at positive angles of attack.

Boltz, Frederick W.↗
NASA NTRS1994

Flow quality studies of the NASA Lewis Research Center Icing Research Tunnel diffuser

The purpose was to document the airflow characteristics in the diffuser of the NASA Lewis Research Center Icing Research Tunnel and to determine the effects of vortex generators on the flow quality in the diffuser. The results were used to determine how to improve the flow in this portion of the tunnel so that it can be more effectively used as an icing test section and such that overall tunnel efficiency can be improved. The demand for tunnel test time and the desire to test models that are too large for the test section were two of the drivers behind this diffuser study. For all vortex generator configurations tested, the flow quality was improved.

Arrington, E. Allen↗
NASA NTRS1971

Numerical calculation of transonic flow about slender bodies of revolution

A relaxation method is described for the numerical solution of the transonic small disturbance equation for flow about a slender body of revolution. Results for parabolic arc bodies, both with and without an attached sting, are compared with wind-tunnel measurements for a free-stream Mach number range from 0.90 to 1.20. The method is also used to show the effects of wind-tunnel wall interference by including boundary conditions representing porous-wall and open-jet wind-tunnel test sections.

Bailey, F. R.↗
NASA NTRS1958

Jet Effects on the Base Drag of a Cylindrical Afterbody with Extended Nozzles

A wind-tunnel investigation to determine the effects of both single and twin jets on base drag of a cylindrical body has been conducted at Mach numbers from 0.6 to 1.4. The plane of the jet exit was varied with respect to that of the afterbody. Jet total-pressure ratio ranged up to 20. Significant improvements in base drag were obtained by extending the plane of the jet exits beyond the afterbody base and by venting the base cavity to the external stream.

Nelson, William J↗
NASA NTRS1973

Effect of fin planform on the aerodynamic characteristics of a wingless missile with AFT cruciform controls at Mach 1.60, 2.36, and 2.86

An investigation was made in the Langley Unitary Plan wind tunnel to determine the effects of fin planform on the static longitudinal aerodynamic characteristics of a wingless maneuvering missile configuration having cruciform, all-movable, aft control surfaces. The tests were made at Mach numbers of 1.60, 2.36, and 2.86 through an angle of attack range from about -4 to 22 deg, at an angle of sideslip of 0 deg, and at a Reynolds number of 8.2 million based on model length. The pitch-control data were obtained at model roll angles of 0 and 45 deg. Control-surface forces and moments were also measured. Four alternate fin planforms were investigated.

Trescot, C. D., Jr.↗