SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Fracture theory for amorphous high polymers below glass transition temperature, considering viscoelastic effects on structural defect stress concentration
A new method of correlating radiation damage data is tested using actual measured data taken from the open literature. This method, the activation fluence method, was found to be as accurate as other contemporary models with which it was compared. The new method also has several advantages over the other methods. The method employs a new entity, the activation fluence (time-integrated specific activation rate), as the independent variables in a regression model. Temperature at which the irradiation takes place is also a variable. Although the method was tested for a specific type of damage (change in nil-ductility transition temperature for A302-B steel) it has no inherent restrictions and is limited only by the imagination of the user.
An extensive development and testing program on adhesive systems shows that: (1) A closed cell silicone rubber sponge bonded to substrates with thin bond lines of glass filled adhesive exhibits density and modulus values approximately one third that of solid silicone adhesives; (2) utilization of glass or phenolic microballoons as fillers in silicone adhesives reduces density but increases moduli of the vulcanized materials; (3) the silicone elastomer based adhesives appear to be complex systems rather than homogeneous, isotropic materials. Tensile, shear, and compression properties plotted versus temperature verify this conjecture; and (4) constant strain-stress relaxation tests on glass-filled adhesive show that stress relaxation is most pronounced near the glass transition temperature.
The work on the properties of thin boron films made by vacuum evaporation of elemental boron using an electron beam as the energy source is reported. The program aimed at characterizing the properties of vacuum evaporated films. The work was directed toward those variables considered to be important in affecting the tensile strength of the boron films. In general, the thickness of the films was less than 0.002 in. The temperature of the substrate on which the boron was condensed was found to be most important. Three distinctly different forms of boron deposit were produced. Although the transition temperature was not sharply defined, at substrate temperatures of less than approximately 600 deg C the boron deposits were amorphous to X-ray. If the substrate were highly polished, the deposits were black and mirror-like. For substrates with coefficients of thermal expansion close to that of boron, the deposits were then continuous and uncracked. The studies suggest that the potential continues to exist for film-type composites to have both high strength and high modulus.
The potential for utilizing surface coatings to inhibit the thermal oxidation of polymer matrix composites was studied. Isothermal, inert gas exposures of graphite/PMR-15 composites indicated that after an initial loss of weight, no significant amounts of thermal degradation products are given off during high temperature exposures in the absence of oxygen. As long as a coating remains effective, the composite material should remain stable. It was also found that the glass transition temperature T sub g of the matrix resin could be increased to values in excess of 400 C. This resulted in measured short beam shear strengths of 75.9 MPa (11 Ksi), flexural strengths of 1172 MPa (170 Ksi) and flexural moduli of 141 GPa (20.5 Msi) for the material at a test temperature of 371 C. The treatment that was used caused a decrease in the PMR-15 resin density from 1.31 to 1.29 gm/cc. It was concluded that state-of-the-art composites, protected by oxygen-impervious coatings, can be used as materials of construction with structural integrity to at least 371 C and possibly above.
The potential for utilizing surface coatings to inhibit the thermal oxidation of polymer matrix composites was studied. Isothermal, inert gas exposures of graphite/PMR-15 composites indicated that after an initial loss of weight, no significant amounts of thermal degradation products are given off during high temperature exposures in the absence of oxygen. As long as a coating remains effective, the composite material should remain stable. It was also found that the glass transition temperature T sub g of the matrix resin could be increased to values in excess of 400 C. This resulted in measured short beam shear strengths of 75.9 MPa (11 Ksi), flexural strengths of 1172 MPa (170 Ksi) and flexural moduli of 141 GPa (20.5 Msi) for the material at a test temperature of 371 C. The treatment that was used caused a decrease in the PMR-15 resin density from 1.31 to 1.29 gm/cc. It was concluded that state-of-the-art composites, protected by oxygen-impervious coatings, can be used as materials of construction with structural integrity to at least 371 C and possibly above.
The hygrothermal aging characteristics of an epoxy resin were characterized over 1 year, which included 908 temperature and humidity cycles. The epoxy resin quickly showed evidence of aging through color change and increased brittleness. The influence of aging on the material s glass transition temperature (Tg) was evaluated by Differential Scanning Calorimetry (DSC) and Dynamic Mechanical Analysis (DMA). The Tg remained relatively constant throughout the year long cyclic aging profile. The chemical composition was monitored by Fourier Transform Infrared Spectroscopy (FTIR) where evidence of chemical aging and advancement of cure was noted. The tensile strength of the resin was tested as it aged. This property was severely affected by the aging process in the form of reduced ductility and embrittlement. Detailed chemical evaluation suggests many aging mechanisms are taking place during exposure to hygrothermal conditions. This paper details the influence of processes such as: advancement of cure, chemical degradation, and physical aging on the chemical and physical properties of the epoxy resin.
Magnetoelectric (ME) composite thin films are promising candidates for novel applications in future nanoelectronics, spintronics, memory and other multifunctional devices as they exhibit much higher ME coupling and transition temperatures (Tc) than well-known single phase multiferroics discovered to date. Among the three types of multiferroic composite nanostructures, (2-2) layered and (1-3) vertically aligned composite nanostructures exhibit comparatively smaller ME coupling due to different shortcomings which restrict their use in many applications. Here we study the morphological, piezoresponse force microscopic (PFM), ferroelectric, magnetic, and magnetodielectric properties of 0-3 (magnetic nanoparticles (0) homogeneously distributed in ferroelectric matrices (3)) multiferroic composite thin films. The Pb(Fe 0.5 Nb 0.5 )O 3 (PFN) - Ni 0.65 Zn 0.35 Fe 2 O 4 (NZFO) particulate composite films were synthesized by pulsed laser deposition (PLD). These particulate composite thin films are completely c-axis oriented with very low surface roughness. We observed magnetic and ferroelectric T c above room temperature (RT) for all composite thin films. The PFN-NZFO 0-3 composites exhibit large polarization, high saturated magnetization with low coercive field, low dielectric loss along with magnetodielectric coupling at RT. These nanocomposites might be utilized in next generation nano/microelectronics and spintronic devices.
A model is described for predicting the wear behavior of whisker reinforced ceramics. The model was successfully applied to a silicon carbide whisker reinforced alumina ceramic composite subjected to sliding contact. The model compares the friction forces on the whiskers due to sliding, which act to pull or push them out of the matrix, to the clamping or compressive forces on the whiskers due to the matrix, which act to hold the whiskers in the composite. At low temperatures, the whiskers are held strongly in the matrix and are fractured into pieces during the wear process along with the matrix. At elevated temperatures differential thermal expansion between the whiskers and matrix can cause loosening of the whiskers and lead to pullout during the wear process and to higher wear. The model, which represents the combination of elastic stress analysis and a friction heating analysis, predicts a transition temperature at which the strength of the whiskers equals the clamping force holding them in the matrix. Above the transition the whiskers are pulled out of the matrix during sliding, and below the transition the whiskers are simply fractured. The existence of the transition gives rise to a dual wear mode or mechanism behavior for this material which was observed in laboratory experiments. The results from this model correlate well with experimentally observed behavior indicating that the model may be useful in obtaining a better understanding of material behavior and in making material improvements.
A model is described for predicting the wear behavior of whisker reinforced ceramics. The model was successfully applied to a silicon carbide whisker reinforced alumina ceramic composite subjected to sliding contact. The model compares the friction forces on the whiskers due to sliding, which act to pull or push them out of the matrix, to the clamping or compressive forces on the whiskers due to the matrix, which act to hold the whiskers in the composite. At low temperatures, the whiskers are held strongly in the matrix and are fractured into pieces during the wear process along with the matrix. At elevated temperatures differential thermal expansion between the whiskers and matrix can cause loosening of the whiskers and lead to pullout during the wear process and to higher wear. The model, which represents the combination of elastic stress analysis and a friction heating analysis, predicts a transition temperature at which the strength of the whiskers equals the clamping force holding them in the matrix. Above the transition the whiskers are pulled out of the matrix during sliding, and below the transition the whiskers are simply fractured. The existence of the transition gives rise to a dual wear mode or mechanism behavior for this material which was observed in laboratory experiments. The results from this model correlate well with experimentally observed behavior indicating that the model may be useful in obtaining a better understanding of material behavior and in making material improvements.
Electrons and holes can spontaneously form excitons and condense in a semimetal or semiconductor, as predicted decades ago. This type of Bose condensation can happen at much higher temperatures in comparison with dilute atomic gases. Two-dimensional (2D) materials with reduced Coulomb screening around the Fermi level are promising for realizing such a system. Here we report a change in the band structure accompanied by a phase transition at about 180 K in single-layer ZrTe 2 based on angle-resolved photoemission spectroscopy (ARPES) measurements. Below the transition temperature, gap opening and development of an ultra-flat band top around the zone center are observed. This gap and the phase transition are rapidly suppressed with extra carrier densities introduced by adding more layers or dopants on the surface. The results suggest the formation of an excitonic insulating ground state in single-layer ZrTe 2 , and the findings are rationalized by first-principles calculations and a self-consistent mean-field theory. Our study provides evidence for exciton condensation in a 2D semimetal and demonstrates strong dimensionality effects on the formation of intrinsic bound electron–hole pairs in solids.
The metal to insulator transition of NbO 2 has been predicted to be a result of a structural phase transition (SPT) governed by Peierls physics. However, direct observation of the SPT using experimental techniques is still restricted by the extremely high transition temperature (810 °C) and the proclivity for NbO 2 to oxidize into Nb 2 O 5 above 400 °C when exposed to air. In this work, we address these issues and employ temperature-dependent X-ray spectroscopy to describe the SPT of NbO 2 from the bulk to surface. Temperature-dependent extended X-ray absorption fine structure spectroscopy (T-EXAFS) reveals a gradual weakening of the bulk Nb dimers over a large temperature range, which is indicative of a second-order Peierls mechanism. From these measurements, we determine the critical dimer distance to be 2.77 Å. Our T-EXAFS observations are supported by density functional theory of the phonon dispersion and the electronic density of states of NbO 2 , which conclude that the dimerization is responsible for the insulating phase. The dimerization does not extend to the topmost layers, where an oxygen rich surface reconstruction is preferred irrespective of temperature even in extremely reducing environments; changes in the low-energy electron diffraction patterns are attributed to oxygen concentration and are independent of the underlying bulk phase transitions of NbO 2 .
Microstructure and defects strongly affect martensitic transformations in metallic alloys. Significant progress has been made in understanding the atomic-level processes that control the role of grain boundaries and precipitates in these solid-to-solid phase transformations. Yet, the role of dislocations and their structures on martensitic transformation temperature and the resulting microstructure remains unclear. Therefore, we used large-scale molecular dynamics simulations to study the forward and reverse transformation of a martensitic material modeled after Ni63Al37 under cyclic thermal loading. The simulations reveal that dislocations in the austenite phase act as one-dimensional seeds for the martensite phase, which is present at temperatures significantly above the martensite start value. We find a reduction in the dislocation density during cyclic thermal loading, which results in the increase in martensite and austenite transition temperatures, in agreement with experiments. Importantly, we extracted a critical martensitic nuclei size for developing stable domains and found that relatively low dislocation densities are needed to grow independent martensitic variants resulting in a multi-domain structure.
A series of N-methyl substituted aromatic polyamides derived from the secondary aromatic diamines, 4,4'-bis(methylamino)diphenylmethane, 3,3'-bis(methylamino) diphenylmethane, 4,4'-bis(methylamino)benzophenone or 3,3'-bis(methylamino)benzophenone and isophthaloyl dichloride, terphthaloyl dichloride or 3,3'diphenylmethane dicarboxylic acid dichloride was prepared by high temperature solution polymerization in s-tetrachloroethane. Compared to analogous unsubstituted and partially N-methylated aromatic polyamides, the full N-methylated polyamides exhibited significantly lower glass transition temperatures, reduced crystallinity, improved thermal stability and good solubility in chlorinated solvents.
The effects of electron radiation and elevated temperature on the matrix-dominated cyclic response of standard T300/934 and a chemically modified T300/934 graphite-epoxy are characterized. Both materials were subjected to 1.0 x 10 to the 10th rads of 1.0 MeV electron irradiation, under vacuum, to simulate 30 years in geosynchronous orbit. Cyclic tests were performed at room temperature and elevated temperature (121 C) on 4-ply unidirectional laminates to characterize the effects associated with irradiation and elevated temperature. Both materials exhibited energy dissipation in their response at elevated temperature. The irradiated modified material also exhibited energy dissipation at room temperature. The combination of elevated temperature and irradiation resulted in the most severe effects in the form of lower proportional limits, and greater energy dissipation. Dynamic-mechanical analysis demonstrated that the glass transition temperature, T(g), of the standard material was lowered 39 C by irradiation, wereas the T(g) of the modified material was lowered 28 C by irradiation. Thermomechanical analysis showed the occurrence of volatile products generated upon heating of the irradiated materials.
This paper reviews the properties of different substituted and unsubstituted polyquinoxalines (PQs) and polyphenylquinoxalines (PPQs), a family of high-performance high-temperature polymers that exhibit high potential for functional and structural applications, and discusses the synthesis of these polymers. Tables are presented of data on the apparent glass-transition temperatures of various PQs and PPQs and on their mechanical properties. Particular consideration is given to the laminate properties of PQ and PPQ composites with glass, boron, and carbon-graphite fibers. Also discussed are the structures and the properties of ladder- and step-ladder-type polymers.
An experimental study was undertaken to establish the viscoelastic behavior of 1M7/K3B composite in compression at elevated temperature. Creep compliance, strain recovery and the effects of physical aging on the time dependent response was measured for uniaxial loading at several isothermal conditions below the glass transition temperature (T(g)). The IM7/K3B composite is a graphite reinforced thermoplastic polyimide with a T(g) of approximately 240 C. In a composite, the two matrix dominated compliance terms associated with time dependent behavior occur in the transverse and shear directions. Linear viscoelasticity was used to characterize the creep/recovery behavior and superposition techniques were used to establish the physical aging related material constants. Creep strain was converted to compliance and measured as a function of test time and aging time. Results included creep compliance master curves, physical aging shift factors and shift rates. The description of the unique experimental techniques required for compressive testing is also given.
Associating polymers have recently attracted tremendous attention as self-healing polymers due to the dynamic reversibility of sticker association–dissociation processes. These sticker dynamics inevitably slow significantly as segmental dynamics decelerate below the glass transition temperature that limits the operational temperatures of associating polymers. Using broadband dielectric spectroscopy on a new set of associating polymers composed side chains of various lengths and terminal carboxylic-acid sticker functionality, we discovered an unexpected decoupling near the glass transition (T g ) between the slower backbone and fast sticker motions. These two motions have distinct activation energies for the motion of the sulfur linkage adjacent to the backbone (~22 to 26 kJ/mol) and the carboxylic acid groups (~5 to 8 kJ/mol). A second decoupling appears in the polymer with the longest side chain length at T g – 20 K, reflecting the dynamics of various carboxylic acid binding configurations. Furthermore, our findings open the door to design associating polymers with the capability of sticker association/dissociation at low temperatures.